| chip soc/intel/skylake |
| |
| register "deep_s5_enable_ac" = "0" |
| register "deep_s5_enable_dc" = "0" |
| register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "GPP_C" |
| register "gpe0_dw1" = "GPP_D" |
| register "gpe0_dw2" = "GPP_E" |
| |
| # Set the fixed lpc ranges |
| # enable COMA at 3f8 and COMB at 3e8 (instead of the default 2f8) |
| # enable the embedded controller |
| register "lpc_iod" = "0x0070" |
| register "lpc_ioe" = "LPC_IOE_COMA_EN | LPC_IOE_COMB_EN | LPC_IOE_EC_62_66" |
| |
| # CPLD host command ranges are in 0x280-0x2BF |
| # EC PNP registers are at 0x6e and 0x6f |
| register "gen1_dec" = "0x003c0281" |
| register "gen3_dec" = "0x0004006d" |
| |
| # LPC serial IRQ |
| register "serirq_mode" = "SERIRQ_CONTINUOUS" |
| |
| # "Intel SpeedStep Technology" |
| register "eist_enable" = "1" |
| |
| # DPTF |
| register "dptf_enable" = "1" |
| |
| # FSP Configuration |
| register "ScsEmmcHs400Enabled" = "1" |
| register "SkipExtGfxScan" = "1" |
| register "SaGv" = "SaGv_Enabled" |
| register "HeciEnabled" = "0" |
| |
| register "SataSalpSupport" = "1" |
| register "SataPortsEnable" = "{ \ |
| [0] = 1, \ |
| [1] = 0, \ |
| [2] = 0, \ |
| [3] = 0, \ |
| [4] = 0, \ |
| [5] = 0, \ |
| [6] = 0, \ |
| [7] = 0, \ |
| }" |
| |
| # Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch |
| # SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s |
| register "PmConfigSlpS3MinAssert" = "2" |
| |
| # SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s |
| register "PmConfigSlpS4MinAssert" = "4" |
| |
| # SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s |
| register "PmConfigSlpSusMinAssert" = "3" |
| |
| # SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s |
| register "PmConfigSlpAMinAssert" = "3" |
| |
| # VR Settings Configuration for 4 Domains |
| #+----------------+-------+-------+-------+-------+ |
| #| Domain/Setting | SA | IA | GTUS | GTS | |
| #+----------------+-------+-------+-------+-------+ |
| #| Psi1Threshold | 20A | 20A | 20A | 20A | |
| #| Psi2Threshold | 5A | 5A | 5A | 5A | |
| #| Psi3Threshold | 1A | 1A | 1A | 1A | |
| #| Psi3Enable | 1 | 1 | 1 | 1 | |
| #| Psi4Enable | 1 | 1 | 1 | 1 | |
| #| ImonSlope | 0 | 0 | 0 | 0 | |
| #| ImonOffset | 0 | 0 | 0 | 0 | |
| #| IccMax | 5.1A | 32A | 35A | 31A | |
| #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | |
| #+----------------+-------+-------+-------+-------+ |
| register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ |
| .vr_config_enable = 1, \ |
| .psi1threshold = VR_CFG_AMP(20), \ |
| .psi2threshold = VR_CFG_AMP(5), \ |
| .psi3threshold = VR_CFG_AMP(1), \ |
| .psi3enable = 1, \ |
| .psi4enable = 1, \ |
| .imon_slope = 0, \ |
| .imon_offset = 0, \ |
| .icc_max = VR_CFG_AMP(5.1), \ |
| .voltage_limit = 1520 \ |
| }" |
| |
| register "domain_vr_config[VR_IA_CORE]" = "{ |
| .vr_config_enable = 1, \ |
| .psi1threshold = VR_CFG_AMP(20), \ |
| .psi2threshold = VR_CFG_AMP(5), \ |
| .psi3threshold = VR_CFG_AMP(1), \ |
| .psi3enable = 1, \ |
| .psi4enable = 1, \ |
| .imon_slope = 0, \ |
| .imon_offset = 0, \ |
| .icc_max = VR_CFG_AMP(32), \ |
| .voltage_limit = 1520 \ |
| }" |
| |
| register "domain_vr_config[VR_GT_UNSLICED]" = "{ |
| .vr_config_enable = 1, \ |
| .psi1threshold = VR_CFG_AMP(20), \ |
| .psi2threshold = VR_CFG_AMP(5), \ |
| .psi3threshold = VR_CFG_AMP(1), \ |
| .psi3enable = 1, \ |
| .psi4enable = 1, \ |
| .imon_slope = 0, \ |
| .imon_offset = 0, \ |
| .icc_max = VR_CFG_AMP(35),\ |
| .voltage_limit = 1520 \ |
| }" |
| |
| register "domain_vr_config[VR_GT_SLICED]" = "{ |
| .vr_config_enable = 1, \ |
| .psi1threshold = VR_CFG_AMP(20), \ |
| .psi2threshold = VR_CFG_AMP(5), \ |
| .psi3threshold = VR_CFG_AMP(1), \ |
| .psi3enable = 1, \ |
| .psi4enable = 1, \ |
| .imon_slope = 0, \ |
| .imon_offset = 0, \ |
| .icc_max = VR_CFG_AMP(31), \ |
| .voltage_limit = 1520 \ |
| }" |
| |
| # Send an extra VR mailbox command for the PS4 exit issue |
| register "SendVrMbxCmd" = "2" |
| |
| # Enable Root ports. |
| # PCIE Port 1 disabled |
| # PCIE Port 2 disabled |
| |
| # PCIE Port 3 x1 -> Module x1 : Mapped to PCIe 2 on the baseboard |
| register "PcieRpEnable[2]" = "1" |
| # Disable CLKREQ# |
| register "PcieRpClkReqSupport[2]" = "0" |
| # Set MaxPayload to 256 bytes |
| register "PcieRpMaxPayload[2]" = "RpMaxPayload_256" |
| # Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[2]" = "1" |
| # Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[2]" = "1" |
| # Disable Aspm |
| register "pcie_rp_aspm[2]" = "AspmDisabled" |
| |
| # PCIE Port 4 disabled |
| # PCIE Port 5 x1 -> MODULE i219 |
| |
| # PCIE Port 6 x1 -> BASEBOARD x1 i210 : Mapped to PCIe 4 on the baseboard |
| register "PcieRpEnable[5]" = "1" |
| register "PcieRpClkReqSupport[5]" = "0" |
| # Set MaxPayload to 256 bytes |
| register "PcieRpMaxPayload[5]" = "RpMaxPayload_256" |
| # Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[5]" = "1" |
| # Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[5]" = "1" |
| # Disable Aspm |
| register "pcie_rp_aspm[5]" = "AspmDisabled" |
| |
| # PCIE Port 7 Disabled |
| # PCIE Port 8 Disabled |
| |
| # PCIE Port 9 x4 -> BASEBOARD PEG0-3 FPGA |
| register "PcieRpEnable[8]" = "1" |
| # Disable CLKREQ# |
| register "PcieRpClkReqSupport[8]" = "0" |
| # Use Hot Plug subsystem |
| register "PcieRpHotPlug[8]" = "1" |
| # Set MaxPayload to 256 bytes |
| register "PcieRpMaxPayload[8]" = "RpMaxPayload_256" |
| # Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[8]" = "1" |
| # Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[8]" = "1" |
| # Disable Aspm |
| register "pcie_rp_aspm[8]" = "AspmDisabled" |
| |
| # USB 2.0 Enable all ports |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB-C Port 2 |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC1)" # USB3_TYPE-A Port 1 |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC1)" # USB3_TYPE-A Port 2 |
| register "usb2_ports[3]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB-C Port 1 |
| register "usb2_ports[4]" = "USB2_PORT_SHORT(OC_SKIP)" # M2 Port |
| register "usb2_ports[6]" = "USB2_PORT_SHORT(OC_SKIP)" # Audio board |
| |
| # USB 3.0 Enable Port 1-4. Port 5 & 6 Disabled |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB-C Port 2 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3_TYPE-A Port 1 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3_TYPE-A Port 2 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB-C Port 1 |
| |
| register "SsicPortEnable" = "0" |
| |
| # Must leave UART0 enabled or SD/eMMC will not work as PCI |
| register "SerialIoDevMode" = "{ \ |
| [PchSerialIoIndexI2C0] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexSpi0] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexSpi1] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexUart0] = PchSerialIoPci, \ |
| [PchSerialIoIndexUart1] = PchSerialIoDisabled, \ |
| [PchSerialIoIndexUart2] = PchSerialIoDisabled, \ |
| }" |
| |
| # Lock Down |
| register "common_soc_config" = "{ |
| .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, |
| }" |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on end # Integrated Graphics Device |
| device pci 04.0 on end # Thermal Subsystem |
| device pci 05.0 off end # SA IMGU |
| device pci 08.0 on end # Gaussian Mixture Model |
| device pci 14.0 on end # USB xHCI |
| device pci 14.1 on end # USB xDCI (OTG) |
| device pci 14.2 on end # Thermal Subsystem |
| device pci 14.3 off end # Camera |
| device pci 17.0 on end # SATA |
| device pci 1c.2 on end # PCI Express Port 3 x1 baseboard WWAN |
| device pci 1c.5 on end # PCI Express Port 6 x1 baseboard i210 |
| device pci 1d.0 on end # PCI Express Port 9 x4 FPGA |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.4 on end # eMMC |
| device pci 1f.0 on # LPC Interface |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| end # LPC Bridge |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 on end # Power Management Controller |
| device pci 1f.3 on end # HDA Controller for HDMI only |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.6 on end # GbE |
| end |
| end |