| /* SPDX-License-Identifier: GPL-2.0-only */ |
| /* This file is part of the coreboot project. */ |
| |
| #include <baseboard/variants.h> |
| #include <chip.h> |
| #include <delay.h> |
| #include <device/device.h> |
| #include <ec/google/chromeec/ec.h> |
| #include <gpio.h> |
| #include <timer.h> |
| |
| #define GPIO_HDMI_HPD GPP_E13 |
| #define GPIO_DP_HPD GPP_E14 |
| |
| /* TODO: This can be moved to common directory */ |
| static void wait_for_hpd(gpio_t gpio, long timeout) |
| { |
| struct stopwatch sw; |
| |
| printk(BIOS_INFO, "Waiting for HPD\n"); |
| stopwatch_init_msecs_expire(&sw, timeout); |
| while (!gpio_get(gpio)) { |
| if (stopwatch_expired(&sw)) { |
| printk(BIOS_WARNING, |
| "HPD not ready after %ldms. Abort.\n", timeout); |
| return; |
| } |
| mdelay(200); |
| } |
| printk(BIOS_INFO, "HPD ready after %lu ms\n", |
| stopwatch_duration_msecs(&sw)); |
| } |
| |
| void variant_ramstage_init(void) |
| { |
| static const long display_timeout_ms = 3000; |
| |
| /* This is reconfigured back to whatever FSP-S expects by |
| gpio_configure_pads. */ |
| gpio_input(GPIO_HDMI_HPD); |
| gpio_input(GPIO_DP_HPD); |
| if (display_init_required() |
| && !gpio_get(GPIO_HDMI_HPD) |
| && !gpio_get(GPIO_DP_HPD)) { |
| /* This has to be done before FSP-S runs. */ |
| if (google_chromeec_wait_for_displayport(display_timeout_ms)) |
| wait_for_hpd(GPIO_DP_HPD, display_timeout_ms); |
| } |
| } |
| |
| /* |
| * For type-C chargers, set PL2 to 90% of max power to account for |
| * cable loss and FET Rdson loss in the path from the source. |
| */ |
| #define SET_PSYSPL2(w) (9 * (w) / 10) |
| |
| #define PUFF_PL2 (35) |
| |
| #define PUFF_PSYSPL2 (58) |
| |
| #define PUFF_MAX_TIME_WINDOW 6 |
| #define PUFF_MIN_DUTYCYCLE 4 |
| |
| /* |
| * mainboard_set_power_limits |
| * |
| * Set Pl2 and SysPl2 values based on detected charger. |
| * Values are defined below but we use U22 value for all SKUs for now. |
| * definitions: |
| * x = no value entered. Use default value in parenthesis. |
| * will set 0 to anything that shouldn't be set. |
| * n = max value of power adapter. |
| * +-------------+-----+---------+-----------+-------+ |
| * | sku_id | PL2 | PsysPL2 | PsysPL3 | PL4 | |
| * +-------------+-----+---------+-----------+-------+ |
| * | i7 U42 | 51 | 81 | x(.85PL4) | x(82) | |
| * | celeron U22 | 35 | 58 | x(.85PL4) | x(51) | |
| * +-------------+-----+---------+-----------+-------+ |
| * For USB C charger: |
| * +-------------+-----+---------+---------+-------+ |
| * | Max Power(W)| PL2 | PsysPL2 | PsysPL3 | PL4 | |
| * +-------------+-----+---------+---------+-------+ |
| * | 60 (U42) | 44 | 54 | 54 | 54 | |
| * | 60 (U22) | 29 | 54 | 54 | x(43) | |
| * | n (U42) | 44 | .9n | .9n | .9n | |
| * | n (U22) | 29 | .9n | .9n | x(43) | |
| * +-------------+-----+---------+---------+-------+ |
| */ |
| static void mainboard_set_power_limits(config_t *conf) |
| { |
| enum usb_chg_type type; |
| u32 watts; |
| u16 volts_mv, current_ma; |
| u32 psyspl2 = PUFF_PSYSPL2; // default barrel jack value for U22 |
| int rv = google_chromeec_get_usb_pd_power_info(&type, ¤t_ma, &volts_mv); |
| |
| /* use SoC default value for PsysPL3 and PL4 unless we're on USB-PD*/ |
| conf->tdp_psyspl3 = 0; |
| conf->tdp_pl4 = 0; |
| |
| if (rv == 0 && type == USB_CHG_TYPE_PD) { |
| /* Detected USB-PD. Base on max value of adapter */ |
| watts = ((u32)current_ma * volts_mv) / 1000000; |
| psyspl2 = watts; |
| conf->tdp_psyspl3 = SET_PSYSPL2(psyspl2); |
| /* set max possible time window */ |
| conf->tdp_psyspl3_time = PUFF_MAX_TIME_WINDOW; |
| /* set minimum duty cycle */ |
| conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE; |
| conf->tdp_pl4 = SET_PSYSPL2(psyspl2); |
| } |
| |
| conf->tdp_pl2_override = PUFF_PL2; |
| /* set psyspl2 to 90% of max adapter power */ |
| conf->tdp_psyspl2 = SET_PSYSPL2(psyspl2); |
| } |
| |
| void variant_mainboard_enable(struct device *dev) |
| { |
| config_t *conf = config_of_soc(); |
| mainboard_set_power_limits(conf); |
| } |