| chip soc/intel/skylake |
| |
| # IGD Displays |
| register "gfx" = "GMA_STATIC_DISPLAYS(0)" |
| |
| register "gpu_pp_up_delay_ms" = "200" |
| register "gpu_pp_down_delay_ms" = " 50" |
| register "gpu_pp_cycle_delay_ms" = "500" |
| register "gpu_pp_backlight_on_delay_ms" = " 1" |
| register "gpu_pp_backlight_off_delay_ms" = "200" |
| |
| register "gpu_pch_backlight_pwm_hz" = "1000" |
| |
| # Enable deep Sx states |
| register "deep_s3_enable_ac" = "0" |
| register "deep_s3_enable_dc" = "0" |
| register "deep_s5_enable_ac" = "1" |
| register "deep_s5_enable_dc" = "1" |
| register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "GPP_B" |
| register "gpe0_dw1" = "GPP_D" |
| register "gpe0_dw2" = "GPP_E" |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| |
| # Enable "Intel Speed Shift Technology" |
| register "speed_shift_enable" = "1" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # FSP Configuration |
| register "ProbelessTrace" = "0" |
| register "SataSalpSupport" = "0" |
| register "SataMode" = "0" |
| register "SataPortsEnable[0]" = "0" |
| register "DspEnable" = "1" |
| register "IoBufferOwnership" = "3" |
| register "SsicPortEnable" = "0" |
| register "Cio2Enable" = "0" |
| register "ScsEmmcHs400Enabled" = "1" |
| register "PttSwitch" = "0" |
| register "SkipExtGfxScan" = "1" |
| register "HeciEnabled" = "0" |
| register "SaGv" = "3" |
| register "PmConfigSlpS3MinAssert" = "2" # 50ms |
| register "PmConfigSlpS4MinAssert" = "4" # 4s |
| register "PmConfigSlpSusMinAssert" = "3" # 4s |
| register "PmConfigSlpAMinAssert" = "3" # 2s |
| register "PmTimerDisabled" = "1" |
| |
| # Enable Root port 1 |
| register "PcieRpEnable[0]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[0]" = "1" |
| # RP 1 uses SRCCLKREQ1# |
| register "PcieRpClkReqNumber[0]" = "1" |
| |
| # Must leave UART0 enabled or SD/eMMC will not work as PCI |
| register "SerialIoDevMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| [PchSerialIoIndexSpi0] = PchSerialIoDisabled, |
| [PchSerialIoIndexSpi1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUart0] = PchSerialIoPci, |
| [PchSerialIoIndexUart1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUart2] = PchSerialIoSkipInit, |
| }" |
| |
| # I2C4 is 1.8V |
| register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" |
| |
| # PL2 override 25W |
| register "power_limits_config" = "{ |
| .tdp_pl2_override = 25, |
| }" |
| |
| # Send an extra VR mailbox command for the PS4 exit issue |
| register "SendVrMbxCmd" = "2" |
| |
| # Lock Down |
| register "common_soc_config" = "{ |
| .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, |
| }" |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on end # Integrated Graphics Device |
| device pci 04.0 on end # SA thermal subsystem |
| device pci 14.0 on end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.2 on end # Thermal Subsystem |
| device pci 15.0 on end # I2C #0 |
| device pci 15.1 on end # I2C #1 |
| device pci 15.2 off end # I2C #2 |
| device pci 15.3 off end # I2C #3 |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT Redirection |
| device pci 16.4 off end # Management Engine Interface 3 |
| device pci 17.0 off end # SATA |
| device pci 19.0 on end # UART #2 |
| device pci 19.1 off end # I2C #5 |
| device pci 19.2 on end # I2C #4 |
| device pci 1c.0 on |
| chip drivers/intel/wifi |
| register "wake" = "GPE0_DW0_16" |
| device pci 00.0 on end |
| end |
| end # PCI Express Port 1 |
| device pci 1c.1 off end # PCI Express Port 2 |
| device pci 1c.2 off end # PCI Express Port 3 |
| device pci 1c.3 off end # PCI Express Port 4 |
| device pci 1c.4 off end # PCI Express Port 5 |
| device pci 1c.5 off end # PCI Express Port 6 |
| device pci 1c.6 off end # PCI Express Port 7 |
| device pci 1c.7 off end # PCI Express Port 8 |
| device pci 1d.0 off end # PCI Express Port 9 |
| device pci 1d.1 off end # PCI Express Port 10 |
| device pci 1d.2 off end # PCI Express Port 11 |
| device pci 1d.3 off end # PCI Express Port 12 |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.1 off end # UART #1 |
| device pci 1e.2 off end # GSPI #0 |
| device pci 1e.3 off end # GSPI #1 |
| device pci 1e.4 on end # eMMC |
| device pci 1e.5 off end # SDIO |
| device pci 1e.6 off end # SDCard |
| device pci 1f.0 on |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| chip ec/google/chromeec |
| device pnp 0c09.0 on end |
| end |
| end # LPC Interface |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 on end # Power Management Controller |
| device pci 1f.3 on end # Intel HDA |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.6 off end # GbE |
| end |
| end |