| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| /* |
| * Include this file into a mainboard's DSDT _SB device tree and it will |
| * expose the F81803A SuperIO and some of its functionality. |
| * |
| * It allows the change of IO ports, IRQs and DMA settings on logical |
| * devices, disabling and reenabling logical devices and controlling power |
| * saving mode on logical devices or the whole chip. |
| * |
| * LDN State |
| * 0x1 UARTA Implemented, partially tested |
| * 0x2 UARTB Implemented, partially tested |
| * 0x4 HWM Not implemented |
| * 0x5 KBC Not implemented |
| * 0x6 GPIO6 Not implemented |
| * 0x7 WDT0&PLED Not implemented |
| * 0xa ACPI/PME/ERP Partially implemented |
| * |
| * Controllable through preprocessor defines: |
| * SUPERIO_DEV Device identifier for this SIO (e.g. SIO0) |
| * SUPERIO_PNP_BASE I/o address of the first PnP configuration register |
| * F81803A_SHOW_UARTA If defined, UARTA will be exposed. |
| * F81803A_SHOW_UARTB If defined, UARTB will be exposed. |
| * F81803A_SHOW_HWMON If defined, the hardware monitor will be exposed. |
| * F81803A_SHOW_PME If defined, the PME/EARP/ACPI will be exposed. |
| * |
| * Known issue: |
| * Do not enable UARTA and UARTB simultaneously, Linux boot will crash. |
| * Select one or the other. |
| */ |
| #undef SUPERIO_CHIP_NAME |
| #define SUPERIO_CHIP_NAME F81803A |
| #include <superio/acpi/pnp.asl> |
| |
| #undef PNP_DEFAULT_PSC |
| #define PNP_DEFAULT_PSC Return (0) /* no power management */ |
| |
| Device(SUPERIO_DEV) { |
| Name (_HID, EisaId("PNP0A05")) |
| Name (_STR, Unicode("Fintek F81803A Super I/O")) |
| Name (_UID, SUPERIO_UID(SUPERIO_DEV,)) |
| |
| /* Mutex for accesses to the configuration ports */ |
| Mutex(CRMX, 1) |
| |
| /* SuperIO configuration ports */ |
| OperationRegion (CREG, SystemIO, SUPERIO_PNP_BASE, 0x02) |
| Field (CREG, ByteAcc, NoLock, Preserve) |
| { |
| PNP_ADDR_REG, 8, |
| PNP_DATA_REG, 8 |
| } |
| IndexField (PNP_ADDR_REG, PNP_DATA_REG, ByteAcc, NoLock, Preserve) |
| { |
| Offset (0x07), |
| PNP_LOGICAL_DEVICE, 8, /* Logical device selector */ |
| Offset (0x30), |
| PNP_DEVICE_ACTIVE, 1, /* Logical device activation */ |
| Offset (0x60), |
| PNP_IO0_HIGH_BYTE, 8, /* First I/O port base - high byte */ |
| PNP_IO0_LOW_BYTE, 8, /* First I/O port base - low byte */ |
| Offset (0x62), |
| PNP_IO1_HIGH_BYTE, 8, /* Second I/O port base - high byte */ |
| PNP_IO1_LOW_BYTE, 8, /* Second I/O port base - low byte */ |
| Offset (0x70), |
| PNP_IRQ0, 8, /* First IRQ */ |
| offset(0xFB), |
| APC5, 8, /* PME ACPI Control Register 5 */ |
| } |
| |
| Method(_CRS) |
| { |
| /* Announce the used i/o ports to the OS */ |
| Return (ResourceTemplate () { |
| IO (Decode16, SUPERIO_PNP_BASE, SUPERIO_PNP_BASE, 0x01, 0x02) |
| }) |
| } |
| |
| #undef PNP_ENTER_MAGIC_1ST |
| #undef PNP_ENTER_MAGIC_2ND |
| #undef PNP_ENTER_MAGIC_3RD |
| #undef PNP_ENTER_MAGIC_4TH |
| #undef PNP_EXIT_MAGIC_1ST |
| #undef PNP_EXIT_SPECIAL_REG |
| #undef PNP_EXIT_SPECIAL_VAL |
| #define PNP_ENTER_MAGIC_1ST 0x87 |
| #define PNP_ENTER_MAGIC_2ND 0x87 |
| #define PNP_EXIT_MAGIC_1ST 0xaa |
| #include <superio/acpi/pnp_config.asl> |
| |
| #ifdef F81803A_SHOW_UARTA |
| #undef SUPERIO_UART_LDN |
| #undef SUPERIO_UART_PM_REG |
| #undef SUPERIO_UART_PM_VAL |
| #undef SUPERIO_UART_PM_LDN |
| #define SUPERIO_UART_LDN 1 |
| |
| Device (SUPERIO_ID(SER, SUPERIO_UART_LDN)) { |
| Name (_HID, EisaId ("PNP0501")) |
| Name (_UID, SUPERIO_UID(SER, SUPERIO_UART_LDN)) |
| |
| Method (_STA) |
| { |
| PNP_GENERIC_STA(SUPERIO_UART_LDN) |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x08, 0x08, IO0) |
| IRQNoFlags (IR0) {} |
| }) |
| ENTER_CONFIG_MODE (SUPERIO_UART_LDN) |
| PNP_READ_IO(PNP_IO0, CRS, IO0) |
| PNP_READ_IRQ(PNP_IRQ0, CRS, IR0) |
| EXIT_CONFIG_MODE () |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x03f8, 0x03f8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02f8, 0x02f8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x03e8, 0x03e8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x02e8, 0x02e8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (2,0) { |
| IO (Decode16, 0x0100, 0x0ff8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x00, 0x00, IO0) |
| IRQNoFlags (IR0) {} |
| }) |
| ENTER_CONFIG_MODE (SUPERIO_UART_LDN) |
| PNP_WRITE_IO(PNP_IO0, Arg0, IO0) |
| PNP_WRITE_IRQ(PNP_IRQ0, Arg0, IR0) |
| PNP_DEVICE_ACTIVE = 1 |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifdef F81803A_SHOW_UARTB |
| #undef SUPERIO_UART_LDN |
| #undef SUPERIO_UART_PM_REG |
| #undef SUPERIO_UART_PM_VAL |
| #undef SUPERIO_UART_PM_LDN |
| #define SUPERIO_UART_LDN 2 |
| |
| Device (SUPERIO_ID(SER, SUPERIO_UART_LDN)) { |
| Name (_HID, EisaId ("PNP0501")) |
| Name (_UID, SUPERIO_UID(SER, SUPERIO_UART_LDN)) |
| |
| Method (_STA) |
| { |
| PNP_GENERIC_STA(SUPERIO_UART_LDN) |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x08, 0x08, IO0) |
| IRQNoFlags (IR0) {} |
| }) |
| ENTER_CONFIG_MODE (SUPERIO_UART_LDN) |
| PNP_READ_IO(PNP_IO0, CRS, IO0) |
| PNP_READ_IRQ(PNP_IRQ0, CRS, IR0) |
| EXIT_CONFIG_MODE () |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x03f8, 0x03f8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02f8, 0x02f8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x03e8, 0x03e8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x02e8, 0x02e8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (2,0) { |
| IO (Decode16, 0x0100, 0x0ff8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x00, 0x00, IO0) |
| IRQNoFlags (IR0) {} |
| }) |
| ENTER_CONFIG_MODE (SUPERIO_UART_LDN) |
| PNP_WRITE_IO(PNP_IO0, Arg0, IO0) |
| PNP_WRITE_IRQ(PNP_IRQ0, Arg0, IR0) |
| PNP_DEVICE_ACTIVE = 1 |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifdef F81803A_SHOW_PME |
| #undef SUPERIO_PME_LDN |
| #define SUPERIO_PME_LDN 0x0A |
| |
| OperationRegion(APCx, SystemIO, APC5, 0x01) |
| Field(APCx, ByteAcc, Nolock, Preserve) /* bits in PME ACPI CONTROL Reg 5*/ |
| { |
| Offset(0x00), /*Control Reg 5 */ |
| , 7, |
| PSIN, 1 /* PSIN_FLAG */ |
| } |
| |
| /* routine to clear PSIN_FLAG in ACPI_CONTROL_REG_5 of SIO */ |
| Method(CPSI, 0, Serialized) |
| { |
| /* DBG0("SIO CPSI") */ |
| ENTER_CONFIG_MODE(SUPERIO_PME_LDN) |
| PSIN = 1 |
| EXIT_CONFIG_MODE() |
| } |
| #endif |
| } |