| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <amdblocks/acpimmio.h> |
| #include <amdblocks/espi.h> |
| #include <bootblock_common.h> |
| #include <baseboard/variants.h> |
| #include <console/console.h> |
| #include <delay.h> |
| #include <device/pci_ops.h> |
| #include <soc/pci_devs.h> |
| #include <timer.h> |
| |
| #define FC350_PCIE_INIT_DELAY_US (20 * USECS_PER_MSEC) |
| struct stopwatch pcie_init_timeout_sw; |
| |
| void mb_set_up_early_espi(void) |
| { |
| /* |
| * We don't need to initialize all of the GPIOs that are done |
| * in bootblock_mainboard_early_init(), but we need to release |
| * the EC eSPI reset and do the rest of the configuration. |
| * |
| * This will not be present in the normal boot flow. |
| */ |
| bootblock_mainboard_early_init(); |
| } |
| |
| void bootblock_mainboard_early_init(void) |
| { |
| uint32_t dword; |
| size_t base_num_gpios, override_num_gpios; |
| const struct soc_amd_gpio *base_gpios, *override_gpios; |
| |
| dword = pci_read_config32(SOC_LPC_DEV, 0x78); |
| dword &= 0xFFFFF9F3; |
| dword |= 0x200; |
| pci_write_config32(SOC_LPC_DEV, 0x78, dword); |
| pci_write_config32(SOC_LPC_DEV, 0x44, 0); |
| pci_write_config32(SOC_LPC_DEV, 0x48, 0); |
| |
| if (CONFIG(VBOOT_STARTS_BEFORE_BOOTBLOCK)) |
| return; |
| |
| base_gpios = variant_early_gpio_table(&base_num_gpios); |
| override_gpios = variant_early_override_gpio_table(&override_num_gpios); |
| |
| gpio_configure_pads_with_override(base_gpios, base_num_gpios, |
| override_gpios, override_num_gpios); |
| |
| /* Set a timer to make sure there's enough delay for |
| * the Fibocom 350 PCIe init |
| */ |
| stopwatch_init_usecs_expire(&pcie_init_timeout_sw, FC350_PCIE_INIT_DELAY_US); |
| printk(BIOS_DEBUG, "Bootblock configure eSPI\n"); |
| |
| dword = pm_read32(0x90); |
| dword |= 1 << 16; |
| pm_write32(0x90, dword); |
| |
| dword = pm_read32(0x74); |
| dword |= 3 << 10; |
| pm_write32(0x74, dword); |
| } |
| |
| void bootblock_mainboard_init(void) |
| { |
| size_t base_num_gpios, override_num_gpios; |
| const struct soc_amd_gpio *base_gpios, *override_gpios; |
| int i = 0; |
| |
| /* Make sure that at least 20ms has elapsed since enabling WWAN power |
| * in bootblock_mainboard_early_init. |
| * This is only applicable if verstage is not in the PSP and the board |
| * is using the fibocom 350 WLAN card, so this typically will not be hit. |
| */ |
| if (!CONFIG(VBOOT_STARTS_BEFORE_BOOTBLOCK) && variant_has_pcie_wwan()) { |
| while (!stopwatch_expired(&pcie_init_timeout_sw)) { |
| mdelay(1); |
| i++; |
| }; |
| if (i) |
| printk(BIOS_DEBUG, "Delayed %d ms for PCIe\n", i); |
| } |
| |
| base_gpios = variant_bootblock_gpio_table(&base_num_gpios); |
| override_gpios = variant_bootblock_override_gpio_table(&override_num_gpios); |
| |
| gpio_configure_pads_with_override(base_gpios, base_num_gpios, override_gpios, |
| override_num_gpios); |
| |
| /* FPMCU check needs to happen after EC initialization for FW_CONFIG bits */ |
| if (variant_has_fpmcu()) |
| variant_fpmcu_reset(); |
| } |