| fw_config |
| field DB_USB 0 2 |
| option USB_ABSENT 0 |
| option USB3_PS8815 1 |
| end |
| field STYLUS 5 |
| option STYLUS_ABSENT 0 |
| option STYLUS_PRESENT 1 |
| end |
| field AUDIO_AMP 7 9 |
| option UNPROVISIONED 0 |
| option MAX98360_ALC5682VS_I2S_2WAY 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # FIVR configurations for brya are disabled since the board doesn't have V1p05 and Vnn |
| # bypass rails implemented. |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| }" |
| |
| register "usb2_ports[0]" = "USB2_PORT_EMPTY" |
| register "usb2_ports[3]" = "USB2_PORT_EMPTY" |
| register "usb3_ports[3]" = "USB3_PORT_EMPTY" |
| |
| register "tcss_ports[0]" = "TCSS_PORT_EMPTY" |
| |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "serial_io_gspi_mode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| }" |
| |
| # As per Intel Advisory doc#723158, the change is required to prevent possible |
| # display flickering issue. |
| register "usb2_phy_sus_pg_disable" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C3 | Touchscreen | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 550, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 550, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 550, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 550, |
| .fall_time_ns = 400, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 160, |
| .scl_hcnt = 70, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| device domain 0 on |
| device ref igpu on |
| chip drivers/gfx/generic |
| register "device_count" = "6" |
| # DDIA for eDP |
| register "device[0].name" = ""LCD0"" |
| # Internal panel on the first port of the graphics chip |
| register "device[0].type" = "panel" |
| # DDIB for HDMI |
| register "device[1].name" = ""DD01"" |
| # TCP0 (DP-1) is unused for any ports but still enumerated in the kernel, so GFX device is added for TCP0 |
| register "device[2].name" = ""DD02"" |
| # TCP1 (DP-2) for port C1 |
| register "device[3].name" = ""DD03"" |
| register "device[2].use_pld" = "true" |
| register "device[2].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| # TCP2 (DP-3) for port C2 |
| register "device[4].name" = ""DD04"" |
| register "device[4].use_pld" = "true" |
| register "device[4].pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| # TCP3 (DP-4) is unused for any ports but still enumerated in the kernel, so GFX device is added for TCP3 |
| register "device[5].name" = ""DD05"" |
| device generic 0 on end |
| end |
| end # Integrated Graphics Device |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DRAM_SOC"" |
| register "options.tsr[1].desc" = ""Ambient"" |
| register "options.tsr[2].desc" = ""Charger"" |
| |
| ## Active Policy |
| register "policies.active" = "{ |
| [0] = { |
| .target = DPTF_TEMP_SENSOR_1, |
| .thresholds = { |
| TEMP_PCT(48, 76), |
| TEMP_PCT(40, 66), |
| TEMP_PCT(38, 53), |
| TEMP_PCT(36, 43), |
| TEMP_PCT(34, 39), |
| TEMP_PCT(32, 33), |
| } |
| } |
| }" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 90, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 60, 5000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 70, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(TEMP_SENSOR_0, 80, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_1, 70, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_2, 80, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 13000, |
| .max_power = 15000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 55000, |
| .max_power = 55000, |
| .time_window_min = 32 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 90, 6700, 220, 2200, }, |
| [1] = { 80, 5800, 180, 1800, }, |
| [2] = { 70, 5000, 145, 1450, }, |
| [3] = { 60, 4900, 115, 1150, }, |
| [4] = { 50, 3838, 90, 900, }, |
| [5] = { 40, 2904, 55, 550, }, |
| [6] = { 30, 2337, 30, 300, }, |
| [7] = { 20, 1608, 15, 150, }, |
| [8] = { 10, 800, 10, 100, }, |
| [9] = { 0, 0, 0, 50, } |
| }" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref tbt_pcie_rp0 off end |
| device ref tbt_pcie_rp1 off end |
| device ref tbt_pcie_rp2 off end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma0 off end |
| device ref tcss_dma1 off end |
| device ref pcie_rp6 off end |
| device ref pcie_rp8 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end #PCIE8 SD card |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_AMP MAX98360_ALC5682VS_I2S_2WAY |
| end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end #I2C1 |
| device ref i2c3 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "300" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_A7)" |
| register "key.wake_gpe" = "GPE0_DW0_08" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on |
| probe STYLUS STYLUS_PRESENT |
| end |
| end |
| end #I2C3 |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end #I2C5 |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn1 as mux_conn[0] |
| use conn2 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 2 alias conn2 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| register "usb_lpm_incapable" = "true" |
| device ref tcss_usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb3_port1 on end |
| end |
| end |
| end |
| end |
| end |
| end |