| chip soc/intel/alderlake |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "pmc_gpe0_dw0" = "GPP_B" |
| register "pmc_gpe0_dw1" = "GPP_D" |
| register "pmc_gpe0_dw2" = "GPP_E" |
| |
| # Enable HECI1 interface |
| register "HeciEnabled" = "1" |
| |
| # FSP configuration |
| |
| # Enable CNVi BT |
| register "CnviBtCore" = "true" |
| |
| # Sagv Configuration |
| register "SaGv" = "SaGv_Enabled" |
| |
| register "usb2_ports[0]" = "USB2_PORT_MID(OC0)" # Type-C Port1 |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC0)" # Type-C Port2 |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC3)" # Type-C Port3 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # M.2 WWAN |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC3)" # Type-C Port4 |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # FPS connector |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC0)" # USB3/2 Type A port1 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC0)" # USB3/2 Type A port2 |
| register "usb2_ports[8]" = "USB2_PORT_MID(OC3)" # USB3/2 Type A port3 |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # M.2 WLAN |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC3)" # USB3/2 Type A port1 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)" # USB3/2 Type A port2 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC0)" # USB3/2 Type A port3 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # M.2 WWAN |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| # EC memory map range is 0x900-0x9ff |
| register "gen3_dec" = "0x00fc0901" |
| |
| # This disabled autonomous GPIO power management, otherwise |
| # old cr50 FW only supports short pulses; need to clarify |
| # the minimum PCH IRQ pulse width with Intel, b/180111628 |
| register "gpio_override_pm" = "1" |
| register "gpio_pm[COMM_0]" = "0" |
| register "gpio_pm[COMM_1]" = "0" |
| register "gpio_pm[COMM_2]" = "0" |
| register "gpio_pm[COMM_4]" = "0" |
| register "gpio_pm[COMM_5]" = "0" |
| |
| # Enable PCH PCIE RP 5 using CLK 2 |
| register "pch_pcie_rp[PCH_RP(5)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_CLK_REQ_DETECT, |
| }" |
| |
| # Enable PCH PCIE RP 6 using CLK 5 |
| register "pch_pcie_rp[PCH_RP(6)]" = "{ |
| .clk_src = 5, |
| .clk_req = 5, |
| .flags = PCIE_RP_CLK_REQ_DETECT, |
| }" |
| |
| # Enable PCH PCIE RP 8 using free running CLK (0x80) |
| # Clock source is shared with LAN and hence marked as free running. |
| register "pch_pcie_rp[PCH_RP(8)]" = "{ |
| .flags = PCIE_RP_CLK_SRC_UNUSED, |
| }" |
| register "pcie_clk_config_flag[6]" = "PCIE_CLK_FREE_RUNNING" |
| |
| # Enable PCH PCIE RP 9 using CLK 1 |
| register "pch_pcie_rp[PCH_RP(9)]" = "{ |
| .clk_src = 1, |
| .clk_req = 1, |
| .flags = PCIE_RP_CLK_REQ_DETECT, |
| }" |
| |
| # Enable PCH PCIE RP 11 for optane |
| register "pch_pcie_rp[PCH_RP(11)]" = "{ |
| .flags = PCIE_RP_CLK_SRC_UNUSED, |
| }" |
| |
| # Hybrid storage mode |
| register "HybridStorageMode" = "1" |
| |
| # Enable CPU PCIE RP 1 using CLK 0 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 0, |
| .clk_src = 0, |
| }" |
| |
| # Enable CPU PCIE RP 2 using CLK 3 |
| register "cpu_pcie_rp[CPU_RP(2)]" = "{ |
| .clk_req = 3, |
| .clk_src = 3, |
| }" |
| |
| # Enable CPU PCIE RP 3 using CLK 4 |
| register "cpu_pcie_rp[CPU_RP(3)]" = "{ |
| .clk_req = 4, |
| .clk_src = 4, |
| }" |
| |
| register "SataSalpSupport" = "1" |
| |
| register "SataPortsEnable" = "{ |
| [0] = 1, |
| [1] = 1, |
| [2] = 1, |
| [3] = 1, |
| }" |
| |
| register "SataPortsDevSlp" = "{ |
| [0] = 1, |
| [1] = 1, |
| [2] = 1, |
| [3] = 1, |
| }" |
| |
| # Enable EDP in PortA |
| register "DdiPortAConfig" = "1" |
| # Enable HDMI in Port B |
| register "ddi_ports_config" = "{ |
| [DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| }" |
| |
| # TCSS USB3 |
| register "TcssAuxOri" = "0" |
| |
| register "s0ix_enable" = "1" |
| register "dptf_enable" = "1" |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "SerialIoGSpiMode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoPci, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI2] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI3] = PchSerialIoDisabled, |
| }" |
| |
| register "SerialIoGSpiCsMode" = "{ |
| [PchSerialIoIndexGSPI0] = 0, |
| [PchSerialIoIndexGSPI1] = 0, |
| [PchSerialIoIndexGSPI2] = 0, |
| [PchSerialIoIndexGSPI3] = 0, |
| }" |
| |
| register "SerialIoGSpiCsState" = "{ |
| [PchSerialIoIndexGSPI0] = 0, |
| [PchSerialIoIndexGSPI1] = 0, |
| [PchSerialIoIndexGSPI2] = 0, |
| [PchSerialIoIndexGSPI3] = 0, |
| }" |
| |
| register "SerialIoUartMode" = "{ |
| [PchSerialIoIndexUART0] = PchSerialIoSkipInit, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoDisabled, |
| }" |
| |
| # HD Audio |
| register "PchHdaDspEnable" = "1" |
| register "PchHdaIDispLinkTmode" = "HDA_TMODE_8T" |
| register "PchHdaIDispLinkFrequency" = "HDA_LINKFREQ_96MHZ" |
| register "PchHdaIDispCodecEnable" = "1" |
| |
| register "CnviBtAudioOffload" = "true" |
| |
| # Intel Common SoC Config |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| # FIVR configurations |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .v1p05_voltage_mv = 1050, |
| .vnn_voltage_mv = 1050, |
| .vnn_sx_voltage_mv = 1050, |
| .v1p05_icc_max_ma = 500, |
| .vnn_icc_max_ma = 500, |
| }" |
| |
| device domain 0 on |
| device ref pcie5 on end |
| device ref igpu on end |
| device ref dtt on |
| chip drivers/intel/dptf |
| |
| ## sensor information |
| register "options.tsr[0].desc" = ""Ambient"" |
| register "options.tsr[1].desc" = ""Battery"" |
| register "options.tsr[2].desc" = ""DDR"" |
| register "options.tsr[3].desc" = ""Skin"" |
| |
| ## Active Policy |
| # TODO: below values are initial reference values only |
| register "policies.active" = "{ |
| [0] = { |
| .target = DPTF_CPU, |
| .thresholds = { |
| TEMP_PCT(95, 90), |
| TEMP_PCT(90, 80), |
| } |
| }, |
| [1] = { |
| .target = DPTF_TEMP_SENSOR_0, |
| .thresholds = { |
| TEMP_PCT(80, 90), |
| TEMP_PCT(70, 80), |
| } |
| } |
| }" |
| |
| ## Passive Policy |
| # TODO: below values are initial reference values only |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 10000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 85, 50000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 85, 50000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 85, 50000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 85, 50000), |
| }" |
| |
| ## Critical Policy |
| # TODO: below values are initial reference values only |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 95, SHUTDOWN), |
| }" |
| |
| ## Power Limits Control |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 35000, |
| .max_power = 45000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 56000, |
| .max_power = 56000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 90, 6700, 220, 2200, }, |
| [1] = { 80, 5800, 180, 1800, }, |
| [2] = { 70, 5000, 145, 1450, }, |
| [3] = { 60, 4900, 115, 1150, }, |
| [4] = { 50, 3838, 90, 900, }, |
| [5] = { 40, 2904, 55, 550, }, |
| [6] = { 30, 2337, 30, 300, }, |
| [7] = { 20, 1608, 15, 150, }, |
| [8] = { 10, 800, 10, 100, }, |
| [9] = { 0, 0, 0, 50, } |
| }" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "2" |
| register "cio2_lanes_used" = "{2,2}" |
| register "cio2_lane_endpoint[0]" = ""^I2C5.CAM1"" |
| register "cio2_lane_endpoint[1]" = ""^I2C1.CAM0"" |
| register "cio2_prt[0]" = "2" |
| register "cio2_prt[1]" = "1" |
| device generic 0 on end |
| end |
| end |
| device ref pcie4_0 on end |
| device ref pcie4_1 on end |
| device ref tbt_pcie_rp0 on end |
| device ref tbt_pcie_rp1 on end |
| device ref tbt_pcie_rp2 on end |
| device ref tbt_pcie_rp3 on end |
| device ref crashlog off end |
| device ref tcss_xhci on end |
| device ref tcss_dma0 on end |
| device ref tcss_dma1 on end |
| device ref xhci on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port10 on end |
| end |
| end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on end |
| device ref i2c1 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "450000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "0" #IMGCLKOUT_0 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_B23" #power_enable |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_R5" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "4" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "3" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF VCM"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C1.CAM0.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0C on end |
| end |
| end |
| device ref i2c2 on end |
| device ref i2c3 on end |
| device ref heci1 on end |
| device ref sata on end |
| device ref i2c5 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM1"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "450000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_E16" #power_enable |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_E15" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "4" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "3" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| end |
| device ref pcie_rp1 on end |
| device ref pcie_rp3 on end # W/A to FSP issue |
| device ref pcie_rp4 on end # W/A to FSP issue |
| device ref pcie_rp5 on end |
| device ref pcie_rp6 on end |
| device ref pcie_rp8 on end |
| device ref pcie_rp9 on end |
| device ref pcie_rp11 on end |
| device ref uart0 on end |
| device ref gspi0 on end |
| device ref p2sb on end |
| device ref hda on |
| chip drivers/intel/soundwire |
| device generic 0 on |
| chip drivers/soundwire/alc711 |
| # SoundWire Link 0 ID 1 |
| register "desc" = ""Headset Codec"" |
| device generic 0.1 on end |
| end |
| end |
| end |
| end |
| device ref smbus on end |
| end |
| end |