| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| |
| /* |
| * JEDEC Standard No. 21-C |
| * Annex K: Serial Presence Detect (SPD) for DDR3 SDRAM Modules 2014 |
| * http://www.jedec.org/sites/default/files/docs/4_01_02_11R24.pdf |
| */ |
| |
| #ifndef DEVICE_DRAM_DDR3L_H |
| #define DEVICE_DRAM_DDR3L_H |
| |
| /** |
| * @file ddr3.h |
| * |
| * \brief Utilities for decoding DDR3 SPDs |
| */ |
| |
| #include <spd.h> |
| #include <device/dram/common.h> |
| #include <types.h> |
| |
| /** |
| * Convenience definitions for SPD offsets |
| * |
| * @{ |
| */ |
| #define SPD_DIMM_MOD_ID1 117 |
| #define SPD_DIMM_MOD_ID2 118 |
| #define SPD_DIMM_SERIAL_NUM 122 |
| #define SPD_DIMM_SERIAL_LEN 4 |
| #define SPD_DIMM_PART_NUM 128 |
| #define SPD_DIMM_PART_LEN 18 |
| /** @} */ |
| |
| /** |
| * \brief Convenience macro for enabling printk with CONFIG(DEBUG_RAM_SETUP) |
| * |
| * Use this macro instead of printk(); for verbose RAM initialization messages. |
| * When CONFIG(DEBUG_RAM_SETUP) is not selected, these messages are automatically |
| * disabled. |
| * @{ |
| */ |
| #if CONFIG(DEBUG_RAM_SETUP) |
| #define printram(x, ...) printk(BIOS_DEBUG, x, ##__VA_ARGS__) |
| #else |
| #define printram(x, ...) |
| #endif |
| /** @} */ |
| |
| /* |
| * Module type (byte 3, bits 3:0) of SPD |
| * This definition is specific to DDR3. DDR2 SPDs have a different structure. |
| */ |
| enum spd_dimm_type_ddr3 { |
| SPD_DDR3_DIMM_TYPE_UNDEFINED = 0x00, |
| SPD_DDR3_DIMM_TYPE_RDIMM = 0x01, |
| SPD_DDR3_DIMM_TYPE_UDIMM = 0x02, |
| SPD_DDR3_DIMM_TYPE_SO_DIMM = 0x03, |
| SPD_DDR3_DIMM_TYPE_MICRO_DIMM = 0x04, |
| SPD_DDR3_DIMM_TYPE_MINI_RDIMM = 0x05, |
| SPD_DDR3_DIMM_TYPE_MINI_UDIMM = 0x06, |
| SPD_DDR3_DIMM_TYPE_MINI_CDIMM = 0x07, |
| SPD_DDR3_DIMM_TYPE_72B_SO_UDIMM = 0x08, |
| SPD_DDR3_DIMM_TYPE_72B_SO_RDIMM = 0x09, |
| SPD_DDR3_DIMM_TYPE_72B_SO_CDIMM = 0x0a, |
| SPD_DDR3_DIMM_TYPE_LRDIMM = 0x0b, |
| SPD_DDR3_DIMM_TYPE_16B_SO_DIMM = 0x0c, |
| SPD_DDR3_DIMM_TYPE_32B_SO_DIMM = 0x0d, |
| /* Masks to bits 3:0 to give the dimm type */ |
| SPD_DDR3_DIMM_TYPE_MASK = 0x0f, |
| }; |
| |
| /** |
| * \brief DIMM flags |
| * |
| * Characteristic flags for the DIMM, as presented by the SPD |
| */ |
| union dimm_flags_ddr3_st { |
| /* The whole point of the union/struct construct is to allow us to clear |
| * all the bits with one line: flags.raw = 0. |
| * We do not care how these bits are ordered */ |
| struct { |
| /* Indicates if rank 1 of DIMM uses a mirrored pin mapping. See: |
| * Annex K: Serial Presence Detect (SPD) for DDR3 SDRAM */ |
| unsigned int pins_mirrored:1; |
| /* Module can work at 1.50V - All DIMMS must be 1.5V operable */ |
| unsigned int operable_1_50V:1; |
| /* Module can work at 1.35V */ |
| unsigned int operable_1_35V:1; |
| /* Module can work at 1.20V */ |
| unsigned int operable_1_25V:1; |
| /* Has an 8-bit bus extension, meaning the DIMM supports ECC */ |
| unsigned int is_ecc:1; |
| /* DLL-Off Mode Support */ |
| unsigned int dll_off_mode:1; |
| /* Indicates a drive strength of RZQ/6 (40 Ohm) is supported */ |
| unsigned int rzq6_supported:1; |
| /* Indicates a drive strength of RZQ/7 (35 Ohm) is supported */ |
| unsigned int rzq7_supported:1; |
| /* Partial Array Self Refresh */ |
| unsigned int pasr:1; |
| /* On-die Thermal Sensor Readout */ |
| unsigned int odts:1; |
| /* Auto Self Refresh */ |
| unsigned int asr:1; |
| /* Extended temperature range supported */ |
| unsigned int ext_temp_range:1; |
| /* Operating at extended temperature requires 2X refresh rate */ |
| unsigned int ext_temp_refresh:1; |
| /* Thermal sensor incorporated */ |
| unsigned int therm_sensor:1; |
| }; |
| unsigned int raw; |
| }; |
| |
| /** |
| * \brief DIMM characteristics |
| * |
| * The characteristics of each DIMM, as presented by the SPD |
| */ |
| struct dimm_attr_ddr3_st { |
| enum spd_memory_type dram_type; |
| enum spd_dimm_type_ddr3 dimm_type; |
| u16 cas_supported; |
| /* Flags extracted from SPD */ |
| union dimm_flags_ddr3_st flags; |
| /* SDRAM width */ |
| u8 width; |
| /* Number of ranks */ |
| u8 ranks; |
| /* Number or row address bits */ |
| u8 row_bits; |
| /* Number or column address bits */ |
| u8 col_bits; |
| /* Size of module in MiB */ |
| u32 size_mb; |
| /* Latencies are in units of 1/256 ns */ |
| u32 tCK; |
| u32 tAA; |
| u32 tWR; |
| u32 tRCD; |
| u32 tRRD; |
| u32 tRP; |
| u32 tRAS; |
| u32 tRC; |
| u32 tRFC; |
| u32 tWTR; |
| u32 tRTP; |
| u32 tFAW; |
| u32 tCWL; |
| u16 tCMD; |
| |
| u8 reference_card; |
| /* XMP: Module voltage in mV */ |
| u16 voltage; |
| /* XMP: max DIMMs per channel supported (1-4) */ |
| u8 dimms_per_channel; |
| /* Manufacturer ID */ |
| u16 manufacturer_id; |
| /* ASCII part number - NULL terminated */ |
| u8 part_number[17]; |
| /* Serial number */ |
| u8 serial[SPD_DIMM_SERIAL_LEN]; |
| }; |
| |
| enum ddr3_xmp_profile { |
| DDR3_XMP_PROFILE_1 = 0, |
| DDR3_XMP_PROFILE_2 = 1, |
| }; |
| |
| typedef u8 spd_raw_data[256]; |
| |
| u16 spd_ddr3_calc_crc(u8 *spd, int len); |
| u16 spd_ddr3_calc_unique_crc(u8 *spd, int len); |
| int spd_decode_ddr3(struct dimm_attr_ddr3_st *dimm, spd_raw_data spd_data); |
| int spd_dimm_is_registered_ddr3(enum spd_dimm_type_ddr3 type); |
| void dram_print_spd_ddr3(const struct dimm_attr_ddr3_st *dimm); |
| int spd_xmp_decode_ddr3(struct dimm_attr_ddr3_st *dimm, |
| spd_raw_data spd, |
| enum ddr3_xmp_profile profile); |
| enum cb_err spd_add_smbios17(const u8 channel, const u8 slot, |
| const u16 selected_freq, |
| const struct dimm_attr_ddr3_st *info); |
| |
| #endif /* DEVICE_DRAM_DDR3L_H */ |