| # SPDX-License-Identifier: GPL-2.0-or-later |
| fw_config |
| field FP 0 |
| option FP_ABSENT 0 |
| option FP_PRESENT 1 |
| end |
| field STYLUS 1 |
| option STYLUS_ABSENT 0 |
| option STYLUS_PRESENT 1 |
| end |
| end |
| |
| chip soc/amd/mendocino |
| |
| register "i2c[0]" = "{ |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_hcnt = 120, |
| .scl_lcnt = 220, |
| .sda_hold = 90, |
| } |
| }" |
| |
| device domain 0 on |
| |
| register "dxio_tx_vboost_enable" = "1" |
| |
| device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A |
| device ref xhci_1 on # XHCI1 controller |
| chip drivers/usb/acpi |
| device ref xhci_1_root_hub on # XHCI1 root hub |
| chip drivers/usb/acpi |
| device ref usb3_port3 on # USB 3.1 port3 |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, CENTER, ACPI_PLD_GROUP(3, 1))" |
| device usb 3.2 on end |
| end |
| end # USB 3.1 port3 |
| end |
| chip drivers/usb/acpi |
| device ref usb2_port3 on # USB 2 port3 |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, CENTER, ACPI_PLD_GROUP(3, 1))" |
| device usb 2.2 on end |
| end |
| end # USB 2 port3 |
| end |
| end # XHCI1 root hub |
| end |
| end # XHCI1 controller |
| end # Internal GPP Bridge 0 to Bus A |
| end # domain |
| |
| device ref i2c_0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_40)" |
| register "wake" = "GEVENT_20" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end # I2C0 |
| device ref i2c_1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_29)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)" |
| register "generic.stop_delay_ms" = "150" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPIO_3)" |
| register "key.dev_name" = ""EJCT"" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| register "key.debounce_interval" = "100" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ" |
| device generic 0 on |
| probe STYLUS STYLUS_PRESENT |
| end |
| end |
| end # I2C1 |
| device ref i2c_2 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "2" |
| register "probed" = "1" |
| device i2c 2a on end |
| end |
| end # I2C2 |
| |
| device ref uart_1 on |
| chip drivers/uart/acpi |
| register "name" = ""CRFP"" |
| register "desc" = ""Fingerprint Reader"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cros-ec-uart"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_24)" |
| register "wake" = "GEVENT_15" |
| register "uart" = "ACPI_UART_RAW_DEVICE(3000000, 64)" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_12)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_4)" |
| register "enable_delay_ms" = "3" |
| device generic 0 alias fpmcu on |
| probe FP FP_PRESENT |
| end |
| end |
| end # UART1 |
| |
| # Set Package Power Parameters |
| register "thermctl_limit_degreeC" = "90" |
| |
| # STT settings |
| register "stt_control" = "1" |
| register "stt_pcb_sensor_count" = "2" |
| register "stt_error_coeff" = "0x21" |
| register "stt_error_rate_coefficient" = "0x2666" |
| register "stt_min_limit" = "15000" |
| register "stt_skin_temp_apu" = "0x3000" |
| |
| # STT default mode |
| register "stt_m1" = "0xfed2" |
| register "stt_m2" = "0x5f9" |
| register "stt_c_apu" = "0xfbf8" |
| register "stt_alpha_apu" = "0x4ccd" |
| |
| # STT tablet mode |
| register "stt_m1_tablet" = "0x208" |
| register "stt_m2_tablet" = "0x1f5" |
| register "stt_c_apu_tablet" = "0xa2" |
| register "stt_alpha_apu_tablet" = "0x199a" |
| |
| end # chip soc/amd/mendocino |