| uses CONFIG_HAVE_MP_TABLE |
| uses CONFIG_HAVE_ACPI_TABLES |
| uses CONFIG_HAVE_ACPI_RESUME |
| uses CONFIG_HAVE_PIRQ_TABLE |
| uses CONFIG_HAVE_FALLBACK_BOOT |
| uses CONFIG_HAVE_OPTION_TABLE |
| uses CONFIG_IRQ_SLOT_COUNT |
| uses CONFIG_MAX_CPUS |
| uses CONFIG_LOGICAL_CPUS |
| uses CONFIG_MAX_PHYSICAL_CPUS |
| uses CONFIG_IOAPIC |
| uses CONFIG_SMP |
| uses CONFIG_ROM_PAYLOAD |
| uses CONFIG_COMPRESSED_PAYLOAD_LZMA |
| uses CONFIG_PRECOMPRESSED_PAYLOAD |
| uses CONFIG_STACK_SIZE |
| uses CONFIG_HEAP_SIZE |
| uses CONFIG_USE_OPTION_TABLE |
| uses CONFIG_LB_CKS_RANGE_START |
| uses CONFIG_LB_CKS_RANGE_END |
| uses CONFIG_LB_CKS_LOC |
| uses CONFIG_MAINBOARD_PART_NUMBER |
| uses CONFIG_MAINBOARD_VENDOR |
| uses CONFIG_MAINBOARD |
| uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID |
| uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID |
| uses CONFIG_RAMBASE |
| uses CONFIG_TTYS0_BAUD |
| uses CONFIG_TTYS0_BASE |
| uses CONFIG_TTYS0_LCS |
| uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL |
| uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL |
| uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL |
| uses CONFIG_CONSOLE_SERIAL8250 |
| uses CONFIG_UDELAY_TSC |
| uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 |
| uses CONFIG_HAVE_INIT_TIMER |
| uses CONFIG_GDB_STUB |
| uses CONFIG_CROSS_COMPILE |
| uses CC |
| uses HOSTCC |
| uses CONFIG_OBJCOPY |
| uses CONFIG_CONSOLE_VGA |
| uses CONFIG_PCI_ROM_RUN |
| uses CONFIG_DEBUG |
| #uses CONFIG_CPU_OPT |
| uses CONFIG_IDE |
| |
| ## These are defined in target Config.lb, don't add here |
| uses CONFIG_USE_FALLBACK_IMAGE |
| uses CONFIG_ROM_SIZE |
| uses CONFIG_ROM_IMAGE_SIZE |
| uses CONFIG_FALLBACK_SIZE |
| uses COREBOOT_EXTRA_VERSION |
| |
| ## These are defined in mainboard Config.lb, don't add here |
| uses CONFIG_ROM_SECTION_SIZE |
| uses CONFIG_ROM_SECTION_OFFSET |
| uses CONFIG_ROMBASE |
| uses CONFIG_XIP_ROM_SIZE |
| uses CONFIG_XIP_ROM_BASE |
| |
| ### |
| ### Build options |
| ### |
| |
| ## |
| ## CONFIG_ROM_SIZE is the size of boot ROM that this board will use. |
| ## |
| default CONFIG_ROM_SIZE=2097152 |
| default CONFIG_ROM_IMAGE_SIZE = 65536 |
| |
| ## |
| ## Build code for the fallback boot? |
| ## |
| default CONFIG_HAVE_FALLBACK_BOOT=1 |
| default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE |
| |
| |
| ## Delay timer options |
| ## |
| default CONFIG_UDELAY_TSC=1 |
| default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 |
| |
| ## |
| ## Build code to export a programmable irq routing table |
| ## |
| default CONFIG_HAVE_PIRQ_TABLE=1 |
| default CONFIG_IRQ_SLOT_COUNT=12 |
| |
| ## |
| ## Build code to export an x86 MP table |
| ## Useful for specifying IRQ routing values |
| ## |
| default CONFIG_HAVE_MP_TABLE=1 |
| |
| ## Build code to export ACPI tables? |
| default CONFIG_HAVE_ACPI_TABLES=1 |
| |
| ## |
| ## Build code to export a CMOS option table? |
| ## |
| default CONFIG_HAVE_OPTION_TABLE=0 |
| |
| ## CMOS checksum definitions (units == bytes) |
| ## These must match the checksum record in cmos.layout |
| default CONFIG_LB_CKS_RANGE_START=128 |
| default CONFIG_LB_CKS_RANGE_END=130 |
| default CONFIG_LB_CKS_LOC=131 |
| |
| ## |
| ## Build code for SMP support |
| ## Only worry about 2 micro processors |
| ## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs, |
| ## so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4. |
| ## |
| default CONFIG_SMP=1 |
| default CONFIG_MAX_CPUS=2 |
| default CONFIG_LOGICAL_CPUS=0 |
| default CONFIG_MAX_PHYSICAL_CPUS=2 |
| |
| # VGA Console |
| # NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS |
| # to VGA.rom |
| default CONFIG_CONSOLE_VGA=0 |
| default CONFIG_PCI_ROM_RUN=0 |
| |
| ## |
| ## Build code to setup a generic IOAPIC |
| ## |
| default CONFIG_IOAPIC=1 |
| |
| ## |
| ## Motherboard identification |
| ## |
| default CONFIG_MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT" |
| default CONFIG_MAINBOARD_VENDOR="Intel" |
| default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086 |
| default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480 |
| |
| ### |
| ### coreboot layout values |
| ### |
| |
| ## |
| ## Use a small 8K stack |
| ## |
| default CONFIG_STACK_SIZE=0x2000 |
| |
| ## |
| ## Use a small 16K heap |
| ## |
| default CONFIG_HEAP_SIZE=0x4000 |
| |
| ## |
| ## CMOS settings not currently supported due to conflicts with factory BIOS |
| ## |
| default CONFIG_USE_OPTION_TABLE = 0 |
| |
| ## |
| ## Coreboot C code runs at this location in RAM |
| ## |
| default CONFIG_RAMBASE=0x00004000 |
| |
| ## |
| ## Load the payload from the ROM |
| ## |
| default CONFIG_ROM_PAYLOAD = 1 |
| |
| ### |
| ### Defaults of options that you may want to override in the target config file |
| ### |
| |
| ## |
| ## The default compiler |
| ## |
| default CC="$(CONFIG_CROSS_COMPILE)gcc -m32" |
| default HOSTCC="gcc" |
| |
| ## |
| ## Disable the gdb stub by default |
| ## |
| default CONFIG_GDB_STUB=0 |
| |
| ## |
| ## The Serial Console |
| ## |
| |
| # To Enable the Serial Console |
| default CONFIG_CONSOLE_SERIAL8250=1 |
| |
| ## Select the serial console baud rate |
| default CONFIG_TTYS0_BAUD=115200 |
| #default CONFIG_TTYS0_BAUD=57600 |
| #default CONFIG_TTYS0_BAUD=38400 |
| #default CONFIG_TTYS0_BAUD=19200 |
| #default CONFIG_TTYS0_BAUD=9600 |
| #default CONFIG_TTYS0_BAUD=4800 |
| #default CONFIG_TTYS0_BAUD=2400 |
| #default CONFIG_TTYS0_BAUD=1200 |
| |
| # Select the serial console base port |
| default CONFIG_TTYS0_BASE=0x3f8 |
| |
| # Select the serial protocol |
| # This defaults to 8 data bits, 1 stop bit, and no parity |
| default CONFIG_TTYS0_LCS=0x3 |
| |
| ## |
| ### Select the coreboot loglevel |
| ## |
| ## EMERG 1 system is unusable |
| ## ALERT 2 action must be taken immediately |
| ## CRIT 3 critical conditions |
| ## ERR 4 error conditions |
| ## WARNING 5 warning conditions |
| ## NOTICE 6 normal but significant condition |
| ## INFO 7 informational |
| ## CONFIG_DEBUG 8 debug-level messages |
| ## SPEW 9 Way too many details |
| |
| ## Request this level of debugging output |
| default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8 |
| ## At a maximum only compile in this level of debugging |
| default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8 |
| |
| ## |
| ## Select power on after power fail setting |
| default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" |
| |
| ## Things we may not have |
| default CONFIG_IDE=1 |
| |
| default CONFIG_DEBUG=1 |
| # default CONFIG_CPU_OPT="-g" |
| |
| ### End Options.lb |
| end |