| fw_config |
| field DB_USB 0 1 |
| option DB_NONE 0 |
| option DB_1C_1A 1 |
| option DB_1C_LTE 2 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "SaGv" = "SaGv_Enabled" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
| |
| device domain 0 on |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "1" |
| device generic 0 on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN6915"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/i2c/sx9324 |
| register "desc" = ""SAR Proximity Sensor"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" |
| register "speed" = "I2C_SPEED_FAST" |
| register "uid" = "1" |
| register "reg_gnrl_ctrl0" = "0x16" |
| register "reg_gnrl_ctrl1" = "0x21" |
| register "reg_afe_ctrl0" = "0x00" |
| register "reg_afe_ctrl1" = "0x10" |
| register "reg_afe_ctrl2" = "0x00" |
| register "reg_afe_ctrl3" = "0x00" |
| register "reg_afe_ctrl4" = "0x07" |
| register "reg_afe_ctrl5" = "0x00" |
| register "reg_afe_ctrl6" = "0x00" |
| register "reg_afe_ctrl7" = "0x07" |
| register "reg_afe_ctrl8" = "0x12" |
| register "reg_afe_ctrl9" = "0x0f" |
| register "reg_prox_ctrl0" = "0x12" |
| register "reg_prox_ctrl1" = "0x12" |
| register "reg_prox_ctrl2" = "0x90" |
| register "reg_prox_ctrl3" = "0x60" |
| register "reg_prox_ctrl4" = "0x0c" |
| register "reg_prox_ctrl5" = "0x12" |
| register "reg_prox_ctrl6" = "0x3c" |
| register "reg_prox_ctrl7" = "0x58" |
| register "reg_adv_ctrl0" = "0x00" |
| register "reg_adv_ctrl1" = "0x00" |
| register "reg_adv_ctrl2" = "0x00" |
| register "reg_adv_ctrl3" = "0x00" |
| register "reg_adv_ctrl4" = "0x00" |
| register "reg_adv_ctrl5" = "0x05" |
| register "reg_adv_ctrl6" = "0x00" |
| register "reg_adv_ctrl7" = "0x00" |
| register "reg_adv_ctrl8" = "0x00" |
| register "reg_adv_ctrl9" = "0x00" |
| register "reg_adv_ctrl10" = "0x5c" |
| register "reg_adv_ctrl11" = "0x52" |
| register "reg_adv_ctrl12" = "0xb5" |
| register "reg_adv_ctrl13" = "0x00" |
| register "reg_adv_ctrl14" = "0x80" |
| register "reg_adv_ctrl15" = "0x0c" |
| register "reg_adv_ctrl16" = "0x38" |
| register "reg_adv_ctrl17" = "0x56" |
| register "reg_adv_ctrl18" = "0x33" |
| register "reg_adv_ctrl19" = "0xf0" |
| register "reg_adv_ctrl20" = "0xf0" |
| device i2c 28 on |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0C on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/nau8825 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" |
| register "jkdet_enable" = "1" |
| register "jkdet_pull_enable" = "0" |
| register "jkdet_polarity" = "1" # ActiveLow |
| register "vref_impedance" = "2" # 125kOhm |
| register "micbias_voltage" = "6" # 2.754 |
| register "sar_threshold_num" = "4" |
| register "sar_threshold[0]" = "0x0c" |
| register "sar_threshold[1]" = "0x1c" |
| register "sar_threshold[2]" = "0x38" |
| register "sar_threshold[3]" = "0x60" |
| register "sar_hysteresis" = "1" |
| register "sar_voltage" = "0" # VDDA |
| register "sar_compare_time" = "0" # 500ns |
| register "sar_sampling_time" = "0" # 2us |
| register "short_key_debounce" = "2" # 100ms |
| register "jack_insert_debounce" = "7" # 512ms |
| register "jack_eject_debounce" = "7" # 512ms |
| device i2c 1a on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref tcss_usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(4, 1)" |
| device ref usb2_port4 on |
| probe DB_USB DB_1C_1A |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F12)" |
| register "reset_off_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "20" |
| device ref usb2_port4 on |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(4, 1)" |
| device ref usb3_port2 on |
| probe DB_USB DB_1C_1A |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port2 on |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| end |
| end |
| end |
| end |
| end |