| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2008-2009 coresystems GmbH |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pci_ids.h> |
| #include <pc80/mc146818rtc.h> |
| #include <pc80/isa-dma.h> |
| #include <pc80/i8259.h> |
| #include <arch/io.h> |
| #include <arch/ioapic.h> |
| #include <arch/acpi.h> |
| #include <cpu/cpu.h> |
| #include "pch.h" |
| |
| #define NMI_OFF 0 |
| |
| #define ENABLE_ACPI_MODE_IN_COREBOOT 0 |
| #define TEST_SMM_FLASH_LOCKDOWN 0 |
| |
| typedef struct southbridge_intel_bd82x6x_config config_t; |
| |
| static void pch_enable_apic(struct device *dev) |
| { |
| int i; |
| u32 reg32; |
| volatile u32 *ioapic_index = (volatile u32 *)(IO_APIC_ADDR); |
| volatile u32 *ioapic_data = (volatile u32 *)(IO_APIC_ADDR + 0x10); |
| |
| /* Enable ACPI I/O and power management. |
| * Set SCI IRQ to IRQ9 |
| */ |
| pci_write_config8(dev, ACPI_CNTL, 0x80); |
| |
| *ioapic_index = 0; |
| *ioapic_data = (1 << 25); |
| |
| /* affirm full set of redirection table entries ("write once") */ |
| *ioapic_index = 1; |
| reg32 = *ioapic_data; |
| *ioapic_index = 1; |
| *ioapic_data = reg32; |
| |
| *ioapic_index = 0; |
| reg32 = *ioapic_data; |
| printk(BIOS_DEBUG, "Southbridge APIC ID = %x\n", (reg32 >> 24) & 0x0f); |
| if (reg32 != (1 << 25)) |
| die("APIC Error\n"); |
| |
| printk(BIOS_SPEW, "Dumping IOAPIC registers\n"); |
| for (i=0; i<3; i++) { |
| *ioapic_index = i; |
| printk(BIOS_SPEW, " reg 0x%04x:", i); |
| reg32 = *ioapic_data; |
| printk(BIOS_SPEW, " 0x%08x\n", reg32); |
| } |
| |
| *ioapic_index = 3; /* Select Boot Configuration register. */ |
| *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */ |
| } |
| |
| static void pch_enable_serial_irqs(struct device *dev) |
| { |
| /* Set packet length and toggle silent mode bit for one frame. */ |
| pci_write_config8(dev, SERIRQ_CNTL, |
| (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0)); |
| #if !CONFIG_SERIRQ_CONTINUOUS_MODE |
| pci_write_config8(dev, SERIRQ_CNTL, |
| (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0)); |
| #endif |
| } |
| |
| /* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control |
| * 0x00 - 0000 = Reserved |
| * 0x01 - 0001 = Reserved |
| * 0x02 - 0010 = Reserved |
| * 0x03 - 0011 = IRQ3 |
| * 0x04 - 0100 = IRQ4 |
| * 0x05 - 0101 = IRQ5 |
| * 0x06 - 0110 = IRQ6 |
| * 0x07 - 0111 = IRQ7 |
| * 0x08 - 1000 = Reserved |
| * 0x09 - 1001 = IRQ9 |
| * 0x0A - 1010 = IRQ10 |
| * 0x0B - 1011 = IRQ11 |
| * 0x0C - 1100 = IRQ12 |
| * 0x0D - 1101 = Reserved |
| * 0x0E - 1110 = IRQ14 |
| * 0x0F - 1111 = IRQ15 |
| * PIRQ[n]_ROUT[7] - PIRQ Routing Control |
| * 0x80 - The PIRQ is not routed. |
| */ |
| |
| static void pch_pirq_init(device_t dev) |
| { |
| device_t irq_dev; |
| /* Get the chip configuration */ |
| config_t *config = dev->chip_info; |
| |
| pci_write_config8(dev, PIRQA_ROUT, config->pirqa_routing); |
| pci_write_config8(dev, PIRQB_ROUT, config->pirqb_routing); |
| pci_write_config8(dev, PIRQC_ROUT, config->pirqc_routing); |
| pci_write_config8(dev, PIRQD_ROUT, config->pirqd_routing); |
| |
| pci_write_config8(dev, PIRQE_ROUT, config->pirqe_routing); |
| pci_write_config8(dev, PIRQF_ROUT, config->pirqf_routing); |
| pci_write_config8(dev, PIRQG_ROUT, config->pirqg_routing); |
| pci_write_config8(dev, PIRQH_ROUT, config->pirqh_routing); |
| |
| /* Eric Biederman once said we should let the OS do this. |
| * I am not so sure anymore he was right. |
| */ |
| |
| for(irq_dev = all_devices; irq_dev; irq_dev = irq_dev->next) { |
| u8 int_pin=0, int_line=0; |
| |
| if (!irq_dev->enabled || irq_dev->path.type != DEVICE_PATH_PCI) |
| continue; |
| |
| int_pin = pci_read_config8(irq_dev, PCI_INTERRUPT_PIN); |
| |
| switch (int_pin) { |
| case 1: /* INTA# */ int_line = config->pirqa_routing; break; |
| case 2: /* INTB# */ int_line = config->pirqb_routing; break; |
| case 3: /* INTC# */ int_line = config->pirqc_routing; break; |
| case 4: /* INTD# */ int_line = config->pirqd_routing; break; |
| } |
| |
| if (!int_line) |
| continue; |
| |
| pci_write_config8(irq_dev, PCI_INTERRUPT_LINE, int_line); |
| } |
| } |
| |
| static void pch_gpi_routing(device_t dev) |
| { |
| /* Get the chip configuration */ |
| config_t *config = dev->chip_info; |
| u32 reg32 = 0; |
| |
| /* An array would be much nicer here, or some |
| * other method of doing this. |
| */ |
| reg32 |= (config->gpi0_routing & 0x03) << 0; |
| reg32 |= (config->gpi1_routing & 0x03) << 2; |
| reg32 |= (config->gpi2_routing & 0x03) << 4; |
| reg32 |= (config->gpi3_routing & 0x03) << 6; |
| reg32 |= (config->gpi4_routing & 0x03) << 8; |
| reg32 |= (config->gpi5_routing & 0x03) << 10; |
| reg32 |= (config->gpi6_routing & 0x03) << 12; |
| reg32 |= (config->gpi7_routing & 0x03) << 14; |
| reg32 |= (config->gpi8_routing & 0x03) << 16; |
| reg32 |= (config->gpi9_routing & 0x03) << 18; |
| reg32 |= (config->gpi10_routing & 0x03) << 20; |
| reg32 |= (config->gpi11_routing & 0x03) << 22; |
| reg32 |= (config->gpi12_routing & 0x03) << 24; |
| reg32 |= (config->gpi13_routing & 0x03) << 26; |
| reg32 |= (config->gpi14_routing & 0x03) << 28; |
| reg32 |= (config->gpi15_routing & 0x03) << 30; |
| |
| pci_write_config32(dev, 0xb8, reg32); |
| } |
| |
| static void pch_power_options(device_t dev) |
| { |
| u8 reg8; |
| u16 reg16, pmbase; |
| u32 reg32; |
| const char *state; |
| /* Get the chip configuration */ |
| config_t *config = dev->chip_info; |
| |
| int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL; |
| int nmi_option; |
| |
| /* Which state do we want to goto after g3 (power restored)? |
| * 0 == S0 Full On |
| * 1 == S5 Soft Off |
| * |
| * If the option is not existent (Laptops), use Kconfig setting. |
| */ |
| get_option(&pwr_on, "power_on_after_fail"); |
| |
| reg16 = pci_read_config16(dev, GEN_PMCON_3); |
| reg16 &= 0xfffe; |
| switch (pwr_on) { |
| case MAINBOARD_POWER_OFF: |
| reg16 |= 1; |
| state = "off"; |
| break; |
| case MAINBOARD_POWER_ON: |
| reg16 &= ~1; |
| state = "on"; |
| break; |
| case MAINBOARD_POWER_KEEP: |
| reg16 &= ~1; |
| state = "state keep"; |
| break; |
| default: |
| state = "undefined"; |
| } |
| |
| reg16 &= ~(3 << 4); /* SLP_S4# Assertion Stretch 4s */ |
| reg16 |= (1 << 3); /* SLP_S4# Assertion Stretch Enable */ |
| |
| reg16 &= ~(1 << 10); |
| reg16 |= (1 << 11); /* SLP_S3# Min Assertion Width 50ms */ |
| |
| reg16 |= (1 << 12); /* Disable SLP stretch after SUS well */ |
| |
| pci_write_config16(dev, GEN_PMCON_3, reg16); |
| printk(BIOS_INFO, "Set power %s after power failure.\n", state); |
| |
| /* Set up NMI on errors. */ |
| reg8 = inb(0x61); |
| reg8 &= 0x0f; /* Higher Nibble must be 0 */ |
| reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */ |
| // reg8 &= ~(1 << 2); /* PCI SERR# Enable */ |
| reg8 |= (1 << 2); /* PCI SERR# Disable for now */ |
| outb(reg8, 0x61); |
| |
| reg8 = inb(0x70); |
| nmi_option = NMI_OFF; |
| get_option(&nmi_option, "nmi"); |
| if (nmi_option) { |
| printk(BIOS_INFO, "NMI sources enabled.\n"); |
| reg8 &= ~(1 << 7); /* Set NMI. */ |
| } else { |
| printk(BIOS_INFO, "NMI sources disabled.\n"); |
| reg8 |= ( 1 << 7); /* Can't mask NMI from PCI-E and NMI_NOW */ |
| } |
| outb(reg8, 0x70); |
| |
| /* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */ |
| reg16 = pci_read_config16(dev, GEN_PMCON_1); |
| reg16 &= ~(3 << 0); // SMI# rate 1 minute |
| reg16 &= ~(1 << 10); // Disable BIOS_PCI_EXP_EN for native PME |
| #if DEBUG_PERIODIC_SMIS |
| /* Set DEBUG_PERIODIC_SMIS in pch.h to debug using |
| * periodic SMIs. |
| */ |
| reg16 |= (3 << 0); // Periodic SMI every 8s |
| #endif |
| pci_write_config16(dev, GEN_PMCON_1, reg16); |
| |
| // Set the board's GPI routing. |
| pch_gpi_routing(dev); |
| |
| pmbase = pci_read_config16(dev, 0x40) & 0xfffe; |
| |
| outl(config->gpe0_en, pmbase + GPE0_EN); |
| outw(config->alt_gp_smi_en, pmbase + ALT_GP_SMI_EN); |
| |
| /* Set up power management block and determine sleep mode */ |
| reg32 = inl(pmbase + 0x04); // PM1_CNT |
| reg32 &= ~(7 << 10); // SLP_TYP |
| reg32 |= (1 << 0); // SCI_EN |
| outl(reg32, pmbase + 0x04); |
| |
| /* Clear magic status bits to prevent unexpected wake */ |
| reg32 = RCBA32(0x3310); |
| reg32 |= (1 << 4)|(1 << 5)|(1 << 0); |
| RCBA32(0x3310) = reg32; |
| |
| reg32 = RCBA32(0x3f02); |
| reg32 &= ~0xf; |
| RCBA32(0x3f02) = reg32; |
| } |
| |
| static void pch_rtc_init(struct device *dev) |
| { |
| u8 reg8; |
| int rtc_failed; |
| |
| reg8 = pci_read_config8(dev, GEN_PMCON_3); |
| rtc_failed = reg8 & RTC_BATTERY_DEAD; |
| if (rtc_failed) { |
| reg8 &= ~RTC_BATTERY_DEAD; |
| pci_write_config8(dev, GEN_PMCON_3, reg8); |
| } |
| printk(BIOS_DEBUG, "rtc_failed = 0x%x\n", rtc_failed); |
| |
| rtc_init(rtc_failed); |
| } |
| |
| /* CougarPoint PCH Power Management init */ |
| static void cpt_pm_init(struct device *dev) |
| { |
| printk(BIOS_DEBUG, "CougarPoint PM init\n"); |
| pci_write_config8(dev, 0xa9, 0x47); |
| RCBA32_AND_OR(0x2238, ~0UL, (1 << 6)|(1 << 0)); |
| RCBA32_AND_OR(0x228c, ~0UL, (1 << 0)); |
| RCBA16_AND_OR(0x1100, ~0UL, (1 << 13)|(1 << 14)); |
| RCBA16_AND_OR(0x0900, ~0UL, (1 << 14)); |
| RCBA32(0x2304) = 0xc0388400; |
| RCBA32_AND_OR(0x2314, ~0UL, (1 << 5)|(1 << 18)); |
| RCBA32_AND_OR(0x2320, ~0UL, (1 << 15)|(1 << 1)); |
| RCBA32_AND_OR(0x3314, ~0x1f, 0xf); |
| RCBA32(0x3318) = 0x050f0000; |
| RCBA32(0x3324) = 0x04000000; |
| RCBA32_AND_OR(0x3340, ~0UL, 0xfffff); |
| RCBA32_AND_OR(0x3344, ~0UL, (1 << 1)); |
| RCBA32(0x3360) = 0x0001c000; |
| RCBA32(0x3368) = 0x00061100; |
| RCBA32(0x3378) = 0x7f8fdfff; |
| RCBA32(0x337c) = 0x000003fc; |
| RCBA32(0x3388) = 0x00001000; |
| RCBA32(0x3390) = 0x0001c000; |
| RCBA32(0x33a0) = 0x00000800; |
| RCBA32(0x33b0) = 0x00001000; |
| RCBA32(0x33c0) = 0x00093900; |
| RCBA32(0x33cc) = 0x24653002; |
| RCBA32(0x33d0) = 0x062108fe; |
| RCBA32_AND_OR(0x33d4, 0xf000f000, 0x00670060); |
| RCBA32(0x3a28) = 0x01010000; |
| RCBA32(0x3a2c) = 0x01010404; |
| RCBA32(0x3a80) = 0x01041041; |
| RCBA32_AND_OR(0x3a84, ~0x0000ffff, 0x00001001); |
| RCBA32_AND_OR(0x3a84, ~0UL, (1 << 24)); /* SATA 2/3 disabled */ |
| RCBA32_AND_OR(0x3a88, ~0UL, (1 << 0)); /* SATA 4/5 disabled */ |
| RCBA32(0x3a6c) = 0x00000001; |
| RCBA32_AND_OR(0x2344, 0x00ffff00, 0xff00000c); |
| RCBA32_AND_OR(0x80c, ~(0xff << 20), 0x11 << 20); |
| RCBA32(0x33c8) = 0; |
| RCBA32_AND_OR(0x21b0, ~0UL, 0xf); |
| } |
| |
| /* PantherPoint PCH Power Management init */ |
| static void ppt_pm_init(struct device *dev) |
| { |
| printk(BIOS_DEBUG, "PantherPoint PM init\n"); |
| pci_write_config8(dev, 0xa9, 0x47); |
| RCBA32_AND_OR(0x2238, ~0UL, (1 << 0)); |
| RCBA32_AND_OR(0x228c, ~0UL, (1 << 0)); |
| RCBA16_AND_OR(0x1100, ~0UL, (1 << 13)|(1 << 14)); |
| RCBA16_AND_OR(0x0900, ~0UL, (1 << 14)); |
| RCBA32(0x2304) = 0xc03b8400; |
| RCBA32_AND_OR(0x2314, ~0UL, (1 << 5)|(1 << 18)); |
| RCBA32_AND_OR(0x2320, ~0UL, (1 << 15)|(1 << 1)); |
| RCBA32_AND_OR(0x3314, ~0x1f, 0xf); |
| RCBA32(0x3318) = 0x054f0000; |
| RCBA32(0x3324) = 0x04000000; |
| RCBA32_AND_OR(0x3340, ~0UL, 0xfffff); |
| RCBA32_AND_OR(0x3344, ~0UL, (1 << 1)|(1 << 0)); |
| RCBA32(0x3360) = 0x0001c000; |
| RCBA32(0x3368) = 0x00061100; |
| RCBA32(0x3378) = 0x7f8fdfff; |
| RCBA32(0x337c) = 0x000003fd; |
| RCBA32(0x3388) = 0x00001000; |
| RCBA32(0x3390) = 0x0001c000; |
| RCBA32(0x33a0) = 0x00000800; |
| RCBA32(0x33b0) = 0x00001000; |
| RCBA32(0x33c0) = 0x00093900; |
| RCBA32(0x33cc) = 0x24653002; |
| RCBA32(0x33d0) = 0x067388fe; |
| RCBA32_AND_OR(0x33d4, 0xf000f000, 0x00670060); |
| RCBA32(0x3a28) = 0x01010000; |
| RCBA32(0x3a2c) = 0x01010404; |
| RCBA32(0x3a80) = 0x01040000; |
| RCBA32_AND_OR(0x3a84, ~0x0000ffff, 0x00001001); |
| RCBA32_AND_OR(0x3a84, ~0UL, (1 << 24)); /* SATA 2/3 disabled */ |
| RCBA32_AND_OR(0x3a88, ~0UL, (1 << 0)); /* SATA 4/5 disabled */ |
| RCBA32(0x3a6c) = 0x00000001; |
| RCBA32_AND_OR(0x2344, 0x00ffff00, 0xff00000c); |
| RCBA32_AND_OR(0x80c, ~(0xff << 20), 0x11 << 20); |
| RCBA32_AND_OR(0x33a4, ~0UL, (1 << 0)); |
| RCBA32(0x33c8) = 0; |
| RCBA32_AND_OR(0x21b0, ~0UL, 0xf); |
| } |
| |
| static void enable_hpet(void) |
| { |
| u32 reg32; |
| |
| /* Move HPET to default address 0xfed00000 and enable it */ |
| reg32 = RCBA32(HPTC); |
| reg32 |= (1 << 7); // HPET Address Enable |
| reg32 &= ~(3 << 0); |
| RCBA32(HPTC) = reg32; |
| } |
| |
| static void enable_clock_gating(device_t dev) |
| { |
| u32 reg32; |
| u16 reg16; |
| |
| RCBA32_AND_OR(0x2234, ~0UL, 0xf); |
| |
| reg16 = pci_read_config16(dev, GEN_PMCON_1); |
| reg16 |= (1 << 2) | (1 << 11); |
| pci_write_config16(dev, GEN_PMCON_1, reg16); |
| |
| pch_iobp_update(0xEB007F07, ~0UL, (1 << 31)); |
| pch_iobp_update(0xEB004000, ~0UL, (1 << 7)); |
| pch_iobp_update(0xEC007F07, ~0UL, (1 << 31)); |
| pch_iobp_update(0xEC004000, ~0UL, (1 << 7)); |
| |
| reg32 = RCBA32(CG); |
| reg32 |= (1 << 31); |
| reg32 |= (1 << 29) | (1 << 28); |
| reg32 |= (1 << 27) | (1 << 26) | (1 << 25) | (1 << 24); |
| reg32 |= (1 << 16); |
| reg32 |= (1 << 17); |
| reg32 |= (1 << 18); |
| reg32 |= (1 << 22); |
| reg32 |= (1 << 23); |
| reg32 &= ~(1 << 20); |
| reg32 |= (1 << 19); |
| reg32 |= (1 << 0); |
| reg32 |= (0xf << 1); |
| RCBA32(CG) = reg32; |
| |
| RCBA32_OR(0x38c0, 0x7); |
| RCBA32_OR(0x36d4, 0x6680c004); |
| RCBA32_OR(0x3564, 0x3); |
| } |
| |
| #if CONFIG_HAVE_SMI_HANDLER |
| static void pch_lock_smm(struct device *dev) |
| { |
| #if TEST_SMM_FLASH_LOCKDOWN |
| u8 reg8; |
| #endif |
| |
| if (acpi_slp_type != 3) { |
| #if ENABLE_ACPI_MODE_IN_COREBOOT |
| printk(BIOS_DEBUG, "Enabling ACPI via APMC:\n"); |
| outb(0xe1, 0xb2); // Enable ACPI mode |
| printk(BIOS_DEBUG, "done.\n"); |
| #else |
| printk(BIOS_DEBUG, "Disabling ACPI via APMC:\n"); |
| outb(0x1e, 0xb2); // Disable ACPI mode |
| printk(BIOS_DEBUG, "done.\n"); |
| #endif |
| } |
| |
| /* Don't allow evil boot loaders, kernels, or |
| * userspace applications to deceive us: |
| */ |
| smm_lock(); |
| |
| #if TEST_SMM_FLASH_LOCKDOWN |
| /* Now try this: */ |
| printk(BIOS_DEBUG, "Locking BIOS to RO... "); |
| reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ |
| printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", |
| (reg8&1)?"rw":"ro"); |
| reg8 &= ~(1 << 0); /* clear BIOSWE */ |
| pci_write_config8(dev, 0xdc, reg8); |
| reg8 |= (1 << 1); /* set BLE */ |
| pci_write_config8(dev, 0xdc, reg8); |
| printk(BIOS_DEBUG, "ok.\n"); |
| reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ |
| printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", |
| (reg8&1)?"rw":"ro"); |
| |
| printk(BIOS_DEBUG, "Writing:\n"); |
| *(volatile u8 *)0xfff00000 = 0x00; |
| printk(BIOS_DEBUG, "Testing:\n"); |
| reg8 |= (1 << 0); /* set BIOSWE */ |
| pci_write_config8(dev, 0xdc, reg8); |
| |
| reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ |
| printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", |
| (reg8&1)?"rw":"ro"); |
| printk(BIOS_DEBUG, "Done.\n"); |
| #endif |
| } |
| #endif |
| |
| static void pch_disable_smm_only_flashing(struct device *dev) |
| { |
| u8 reg8; |
| |
| printk(BIOS_SPEW, "Enabling BIOS updates outside of SMM... "); |
| reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ |
| reg8 &= ~(1 << 5); |
| pci_write_config8(dev, 0xdc, reg8); |
| } |
| |
| static void pch_fixups(struct device *dev) |
| { |
| u8 gen_pmcon_2; |
| |
| /* Indicate DRAM init done for MRC S3 to know it can resume */ |
| gen_pmcon_2 = pci_read_config8(dev, GEN_PMCON_2); |
| gen_pmcon_2 |= (1 << 7); |
| pci_write_config8(dev, GEN_PMCON_2, gen_pmcon_2); |
| |
| /* |
| * Enable DMI ASPM in the PCH |
| */ |
| RCBA32_AND_OR(0x2304, ~(1 << 10), 0); |
| RCBA32_OR(0x21a4, (1 << 11)|(1 << 10)); |
| RCBA32_OR(0x21a8, 0x3); |
| } |
| |
| static void pch_decode_init(struct device *dev) |
| { |
| config_t *config = dev->chip_info; |
| |
| printk(BIOS_DEBUG, "pch_decode_init\n"); |
| |
| pci_write_config32(dev, LPC_GEN1_DEC, config->gen1_dec); |
| pci_write_config32(dev, LPC_GEN2_DEC, config->gen2_dec); |
| pci_write_config32(dev, LPC_GEN3_DEC, config->gen3_dec); |
| pci_write_config32(dev, LPC_GEN4_DEC, config->gen4_dec); |
| } |
| |
| static void lpc_init(struct device *dev) |
| { |
| printk(BIOS_DEBUG, "pch: lpc_init\n"); |
| |
| /* Set the value for PCI command register. */ |
| pci_write_config16(dev, PCI_COMMAND, 0x000f); |
| |
| /* IO APIC initialization. */ |
| pch_enable_apic(dev); |
| |
| pch_enable_serial_irqs(dev); |
| |
| /* Setup the PIRQ. */ |
| pch_pirq_init(dev); |
| |
| /* Setup power options. */ |
| pch_power_options(dev); |
| |
| /* Initialize power management */ |
| switch (pch_silicon_type()) { |
| case PCH_TYPE_CPT: /* CougarPoint */ |
| cpt_pm_init(dev); |
| break; |
| case PCH_TYPE_PPT: /* PantherPoint */ |
| ppt_pm_init(dev); |
| break; |
| default: |
| printk(BIOS_ERR, "Unknown Chipset: 0x%04x\n", dev->device); |
| } |
| |
| /* Set the state of the GPIO lines. */ |
| //gpio_init(dev); |
| |
| /* Initialize the real time clock. */ |
| pch_rtc_init(dev); |
| |
| /* Initialize ISA DMA. */ |
| isa_dma_init(); |
| |
| /* Initialize the High Precision Event Timers, if present. */ |
| enable_hpet(); |
| |
| /* Initialize Clock Gating */ |
| enable_clock_gating(dev); |
| |
| setup_i8259(); |
| |
| /* The OS should do this? */ |
| /* Interrupt 9 should be level triggered (SCI) */ |
| i8259_configure_irq_trigger(9, 1); |
| |
| pch_disable_smm_only_flashing(dev); |
| |
| #if CONFIG_HAVE_SMI_HANDLER |
| pch_lock_smm(dev); |
| #endif |
| |
| pch_fixups(dev); |
| } |
| |
| static void pch_lpc_read_resources(device_t dev) |
| { |
| struct resource *res; |
| |
| /* Get the normal PCI resources of this device. */ |
| pci_dev_read_resources(dev); |
| |
| /* Add an extra subtractive resource for both memory and I/O. */ |
| res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0)); |
| res->base = 0; |
| res->size = 0x1000; |
| res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | |
| IORESOURCE_ASSIGNED | IORESOURCE_FIXED; |
| |
| res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0)); |
| res->base = 0xff800000; |
| res->size = 0x00800000; /* 8 MB for flash */ |
| res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | |
| IORESOURCE_ASSIGNED | IORESOURCE_FIXED; |
| |
| res = new_resource(dev, 3); /* IOAPIC */ |
| res->base = IO_APIC_ADDR; |
| res->size = 0x00001000; |
| res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED; |
| } |
| |
| static void pch_lpc_enable_resources(device_t dev) |
| { |
| pch_decode_init(dev); |
| return pci_dev_enable_resources(dev); |
| } |
| |
| static void pch_lpc_enable(device_t dev) |
| { |
| /* Enable PCH Display Port */ |
| RCBA16(DISPBDF) = 0x0010; |
| RCBA32_OR(FD2, PCH_ENABLE_DBDF); |
| |
| pch_enable(dev); |
| } |
| |
| static void set_subsystem(device_t dev, unsigned vendor, unsigned device) |
| { |
| if (!vendor || !device) { |
| pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, |
| pci_read_config32(dev, PCI_VENDOR_ID)); |
| } else { |
| pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, |
| ((device & 0xffff) << 16) | (vendor & 0xffff)); |
| } |
| } |
| |
| static struct pci_operations pci_ops = { |
| .set_subsystem = set_subsystem, |
| }; |
| |
| static struct device_operations device_ops = { |
| .read_resources = pch_lpc_read_resources, |
| .set_resources = pci_dev_set_resources, |
| .enable_resources = pch_lpc_enable_resources, |
| .init = lpc_init, |
| .enable = pch_lpc_enable, |
| .scan_bus = scan_static_bus, |
| .ops_pci = &pci_ops, |
| }; |
| |
| |
| /* IDs for LPC device of Intel 6 series Chipset and |
| * Intel C200 Series Chipset according to specification |
| * update from August 2011 |
| */ |
| |
| static const unsigned short pci_device_ids[] = { 0x1c46, 0x1c47, 0x1c49, 0x1c4a, |
| 0x1c4b, 0x1c4c, 0x1c4d, 0x1c4e, |
| 0x1c4f, 0x1c50, 0x1c52, 0x1c54, |
| 0x1e55, 0x1c56, 0x1c5c, 0x1e5d, |
| 0x1e5e, 0x1e5f, |
| 0 }; |
| |
| static const struct pci_driver pch_lpc __pci_driver = { |
| .ops = &device_ops, |
| .vendor = PCI_VENDOR_ID_INTEL, |
| .devices = pci_device_ids, |
| }; |
| |
| |