| /* this setupcpu function comes from: */ |
| /*==============================================================================*/ |
| /* FILE : start16.asm*/ |
| /**/ |
| /* DESC : A 16 bit mode assembly language startup program, intended for*/ |
| /* use with on Aspen SC520 platforms.*/ |
| /**/ |
| /* 11/16/2000 Added support for the NetSC520*/ |
| /* 12/28/2000 Modified to boot linux image*/ |
| /**/ |
| /* =============================================================================*/ |
| /* */ |
| /* Copyright 2000 Advanced Micro Devices, Inc. */ |
| /* */ |
| /* This software is the property of Advanced Micro Devices, Inc (AMD) which */ |
| /* specifically grants the user the right to modify, use and distribute this */ |
| /* software provided this COPYRIGHT NOTICE is not removed or altered. All */ |
| /* other rights are reserved by AMD. */ |
| /* */ |
| /* THE MATERIALS ARE PROVIDED "AS IS" WITHOUT ANY EXPRESS OR IMPLIED WARRANTY */ |
| /* OF ANY KIND INCLUDING WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT OF */ |
| /* THIRD-PARTY INTELLECTUAL PROPERTY, OR FITNESS FOR ANY PARTICULAR PURPOSE.*/ |
| /* IN NO EVENT SHALL AMD OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER*/ |
| /* (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS*/ |
| /* INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY*/ |
| /* TO USE THE MATERIALS, EVEN IF AMD HAS BEEN ADVISED OF THE POSSIBILITY OF*/ |
| /* SUCH DAMAGES. BECAUSE SOME JURSIDICTIONS PROHIBIT THE EXCLUSION OR*/ |
| /* LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE*/ |
| /* LIMITATION MAY NOT APPLY TO YOU.*/ |
| /**/ |
| /* AMD does not assume any responsibility for any errors that may appear in*/ |
| /* the Materials nor any responsibility to support or update the Materials.*/ |
| /* AMD retains the right to make changes to its test specifications at any*/ |
| /* time, without notice.*/ |
| /**/ |
| /* So that all may benefit from your experience, please report any problems */ |
| /* or suggestions about this software back to AMD. Please include your name, */ |
| /* company, telephone number, AMD product requiring support and question or */ |
| /* problem encountered. */ |
| /* */ |
| /* Advanced Micro Devices, Inc. Worldwide support and contact */ |
| /* Embedded Processor Division information available at: */ |
| /* Systems Engineering epd.support@amd.com*/ |
| /* 5204 E. Ben White Blvd. -or-*/ |
| /* Austin, TX 78741 http://www.amd.com/html/support/techsup.html*/ |
| /* ============================================================================*/ |
| |
| |
| #define OUTC(addr, val) *(unsigned char *)(addr) = (val) |
| |
| /* sadly, romcc can't quite handle what we want, so we do this ugly thing */ |
| #define drcctl (( volatile unsigned char *)0xfffef010) |
| #define drcmctl (( volatile unsigned char *)0xfffef012) |
| #define drccfg (( volatile unsigned char *)0xfffef014) |
| |
| #define drcbendadr (( volatile unsigned long *)0xfffef018) |
| #define eccctl (( volatile unsigned char *)0xfffef020) |
| #define dbctl (( volatile unsigned char *)0xfffef040) |
| |
| void setupsc520(void) |
| { |
| volatile unsigned char *cp; |
| volatile unsigned short *sp; |
| volatile unsigned long *edi; |
| |
| /* do this to see if MMCR will start acting right. we suspect |
| * you have to do SOMETHING to get things going. I'm really |
| * starting to hate this processor. |
| */ |
| |
| /* no, that did not help. I wonder what will? |
| * outl(0x800df0cb, 0xfffc); |
| */ |
| |
| /* well, this is special! You have to do SHORT writes to the |
| * locations, even though they are CHAR in size and CHAR aligned |
| * and technically, a SHORT write will result in -- yoo ha! -- |
| * over writing the next location! Thanks to the u-boot guys |
| * for a reference code I can use. with these short pointers, |
| * it now reliably comes up after power cycle with printk. Ah yi |
| * yi. |
| */ |
| |
| /* turn off the write buffer*/ |
| /* per the note above, make this a short? Let's try it. */ |
| sp = (unsigned short *)0xfffef040; |
| *sp = 0; |
| |
| /* as per the book: */ |
| /* PAR register setup */ |
| /* set up the PAR registers as they are on the MSM586SEG */ |
| /* moved to auto.c by Stepan, Ron says: */ |
| /* NOTE: move this to mainboard.c ASAP */ |
| setup_pars(); |
| |
| /* CPCSF register */ |
| sp = (unsigned short *)0xfffefc24; |
| *sp = 0xfe; |
| |
| /* ADDDECTL */ |
| sp = (unsigned short *)0xfffefc80; |
| *sp = 0x10; |
| |
| /* byte writes in AMD assembly */ |
| /* we do short anyway, since u-boot does ... */ |
| /*set the GP CS offset*/ |
| sp = (unsigned short *)0xfffefc08; |
| *sp = 0x00001; |
| /*set the GP CS width*/ |
| sp = (unsigned short *)0xfffefc09; |
| *sp = 0x00003; |
| |
| /* short writes in AMD assembly */ |
| /*set the GP CS width*/ |
| sp = (unsigned short *)0xfffefc0a; |
| *sp = 0x00001; |
| /*set the RD pulse width*/ |
| sp = (unsigned short *)0xfffefc0b; |
| *sp = 0x00003; |
| /*set the GP RD offset */ |
| sp = (unsigned short *)0xfffefc0c; |
| *sp = 0x00001; |
| /*set the GP WR pulse width*/ |
| sp = (unsigned short *)0xfffefc0d; |
| *sp = 0x00003; |
| /*set the GP WR offset*/ |
| sp = (unsigned short *)0xfffefc0e; |
| *sp = 0x00001; |
| |
| |
| /* set up the GP IO pins*/ |
| /*set the GPIO directionreg*/ |
| sp = (unsigned short *)0xfffefc2c; |
| *sp = 0x00000; |
| /*set the GPIO directionreg*/ |
| sp = (unsigned short *)0xfffefc2a; |
| *sp = 0x00000; |
| /*set the GPIO pin function 31-16 reg*/ |
| sp = (unsigned short *)0xfffefc22; |
| *sp = 0x0FFFF; |
| /*set the GPIO pin function 15-0 reg*/ |
| sp = (unsigned short *)0xfffefc20; |
| *sp = 0x0FFFF; |
| |
| |
| /* the 0x80 led should now be working*/ |
| outb(0xaa, 0x80); |
| #if 0 |
| /* wtf are 680 leds ... */ |
| par = (unsigned long *) 0xfffef0c4; |
| *par = 0x28000680; |
| /* well? */ |
| outb(0x55, 0x80); |
| #endif |
| |
| /* set the uart baud rate clocks to the normal 1.8432 MHz.*/ |
| /* enable interrupts here? Why not? */ |
| cp = (unsigned char *)0xfffefcc0; |
| *cp = 4 | 3; /* uart 1 clock source */ |
| cp = (unsigned char *)0xfffefcc4; |
| *cp = 4; /* uart 2 clock source */ |
| |
| #if 0 |
| /*; set the interrupt mapping registers.*/ |
| cp = (unsigned char *)0x0fffefd20; |
| *cp = 0x01; |
| |
| cp = (unsigned char *)0x0fffefd28; |
| *cp = 0x0c; |
| |
| cp = (unsigned char *)0x0fffefd29; |
| *cp = 0x0b; |
| |
| cp = (unsigned char *)0x0fffefd30; |
| *cp = 0x07; |
| |
| cp = (unsigned char *)0x0fffefd43; |
| *cp = 0x03; |
| |
| cp = (unsigned char *)0x0fffefd51; |
| *cp = 0x02; |
| #endif |
| |
| /* Stepan says: This needs to go to the msm586seg code */ |
| /* "enumerate" the PCI. Mainly set the interrupt bits on the PCnetFast. */ |
| outl(0xcf8, 0x08000683c); |
| outl(0xcfc, 0xc); /* set the interrupt line */ |
| |
| |
| /* Set the SC520 PCI host bridge to target mode to |
| * allow external bus mastering events |
| */ |
| /* index the status command register on device 0*/ |
| outl(0x0cf8,0x080000004); |
| outl(0xcfc, 0x2); /*set the memory access enable bit*/ |
| OUTC(0x0fffef072, 1); /* enable req bits in SYSARBMENB */ |
| } |
| |
| |
| /* |
| * |
| * |
| */ |
| |
| |
| |
| #define CACHELINESZ 0x00000010 /* size of our cache line (read buffer)*/ |
| |
| #define COL11_ADR *(unsigned int *)0x0e001e00 /* 11 col addrs*/ |
| #define COL10_ADR *(unsigned int *)0x0e000e00 /* 10 col addrs*/ |
| #define COL09_ADR *(unsigned int *)0x0e000600 /* 9 col addrs*/ |
| #define COL08_ADR *(unsigned int *)0x0e000200 /* 8 col addrs*/ |
| |
| #define ROW14_ADR *(unsigned int *)0x0f000000 /* 14 row addrs*/ |
| #define ROW13_ADR *(unsigned int *)0x07000000 /* 13 row addrs*/ |
| #define ROW12_ADR *(unsigned int *)0x03000000 /* 12 row addrs*/ |
| #define ROW11_ADR *(unsigned int *)0x01000000 /* 11 row addrs/also bank switch*/ |
| #define ROW10_ADR *(unsigned int *)0x00000000 /* 10 row addrs/also bank switch*/ |
| |
| #define COL11_DATA 0x0b0b0b0b /* 11 col addrs*/ |
| #define COL10_DATA 0x0a0a0a0a /* 10 col data*/ |
| #define COL09_DATA 0x09090909 /* 9 col data*/ |
| #define COL08_DATA 0x08080808 /* 8 col data*/ |
| |
| #define ROW14_DATA 0x3f3f3f3f /* 14 row data (MASK)*/ |
| #define ROW13_DATA 0x1f1f1f1f /* 13 row data (MASK)*/ |
| #define ROW12_DATA 0x0f0f0f0f /* 12 row data (MASK)*/ |
| #define ROW11_DATA 0x07070707 /* 11 row data/also bank switch (MASK)*/ |
| #define ROW10_DATA 0xaaaaaaaa /* 10 row data/also bank switch (MASK)*/ |
| |
| void |
| dummy_write(void){ |
| volatile unsigned short *ptr = (volatile unsigned short *)CACHELINESZ; |
| *ptr = 0; |
| } |
| |
| void sc520_udelay(int microseconds) { |
| volatile int x; |
| for(x = 0; x < 1000; x++) |
| ; |
| } |
| |
| /* looks like we define this now */ |
| void |
| udelay(int microseconds) { |
| sc520_udelay(microseconds); |
| } |
| |
| |
| static void dumpram(void){ |
| print_err("ctl "); print_err_hex8(*drcctl); print_err("\r\n"); |
| print_err("mctl "); print_err_hex8(*drcmctl); print_err("\r\n"); |
| print_err("cfg "); print_err_hex8(*drccfg); print_err("\r\n"); |
| |
| print_err("bendadr0 "); print_err_hex8(*drcbendadr); print_err("\r\n"); |
| print_err("bendadr1 "); print_err_hex8(*drcbendadr); print_err("\r\n"); |
| print_err("bendadr2 "); print_err_hex8(*drcbendadr); print_err("\r\n"); |
| print_err("bendadr3"); print_err_hex8(*drcbendadr); print_err("\r\n"); |
| } |
| |
| /* there is a lot of silliness in the amd code, and it is |
| * causing romcc real headaches, so we're going to be be a little |
| * less silly. |
| * so, the order of ops is: |
| * for i in 3 to 0 |
| * see if bank is there. |
| * if we can write a word, and read it back, to hell with paranoia |
| * the bank is there. So write the magic byte, read it back, and |
| * use that to get size, etc. Try to keep things very simple, |
| * so people can actually follow the damned code. |
| */ |
| |
| /* cache is assumed to be disabled */ |
| int sizemem(void) |
| { |
| |
| int rows,banks, cols, i, bank; |
| unsigned char al; |
| volatile unsigned long *lp = (volatile unsigned long *) CACHELINESZ; |
| unsigned long l; |
| /* initialize dram controller registers */ |
| /* disable write buffer/read-ahead buffer */ |
| *dbctl = 0; |
| /* no ecc interrupts of any kind. */ |
| *eccctl = 0; |
| /* Set SDRAM timing for slowest speed. */ |
| *drcmctl = 0x1e; |
| |
| /* setup dram register for all banks |
| * with max cols and max banks |
| * this is the oldest trick in the book. You are going to set up for max rows |
| * and cols, then do a write, then see if the data is wrapped to low memory. |
| * you can actually tell by which data gets to which low memory, |
| * exactly how many rows and cols you have. |
| */ |
| *drccfg=0xbbbb; |
| |
| /* setup loop to do 4 external banks starting with bank 3 */ |
| *drcbendadr=0x0ff000000; |
| /* for now, set it up for one loop of bank 0. Just to get it to go at all. */ |
| *drcbendadr=0x0ff; |
| |
| /* issue a NOP to all DRAMs */ |
| /* Setup DRAM control register with Disable refresh, |
| * disable write buffer Test Mode and NOP command select |
| */ |
| *drcctl=0x01; |
| |
| /* dummy write for NOP to take effect */ |
| dummy_write(); |
| print_err("NOP\n"); |
| /* 100? 200? */ |
| udelay(100); |
| print_err("after sc520_udelay\r\n"); |
| |
| /* issue all banks precharge */ |
| *drcctl=0x02; |
| print_err("set *drcctl to 2 \r\n"); |
| dummy_write(); |
| print_err("PRE\n"); |
| |
| /* issue 2 auto refreshes to all banks */ |
| *drcctl=0x04; |
| dummy_write(); |
| print_err("AUTO1\n"); |
| dummy_write(); |
| print_err("AUTO2\n"); |
| |
| /* issue LOAD MODE REGISTER command */ |
| *drcctl=0x03; |
| dummy_write(); |
| print_err("LOAD MODE REG\n"); |
| |
| *drcctl=0x04; |
| for (i=0; i<8; i++) /* refresh 8 times */{ |
| dummy_write(); |
| print_err("dummy write\r\n"); |
| } |
| print_err("8 dummy writes\n"); |
| |
| /* set control register to NORMAL mode */ |
| *drcctl=0x00; |
| print_err("normal\n"); |
| |
| print_err("HI done normal\r\n"); |
| |
| print_err("sizemem\n"); |
| for(bank = 3; bank >= 0; bank--) { |
| print_err("Try to assign to l\r\n"); |
| *lp = 0xdeadbeef; |
| print_err("assigned l ... \r\n"); |
| if (*lp != 0xdeadbeef) { |
| print_err(" no memory at bank "); |
| // print_err_hex8(bank); |
| // print_err(" value "); print_err_hex32(*lp); |
| print_err("\r\n"); |
| // continue; |
| } |
| *drcctl = 2; |
| dummy_write(); |
| *drccfg = *drccfg >> 4; |
| l = *drcbendadr; |
| l >>= 8; |
| *drcbendadr = l; |
| print_err("loop around\r\n"); |
| *drcctl = 0; |
| dummy_write(); |
| } |
| #if 0 |
| /* enable last bank and setup ending address |
| * register for max ram in last bank |
| */ |
| *drcbendadr=0x0ff000000; |
| |
| |
| // dumpram(); |
| |
| /* issue a NOP to all DRAMs */ |
| /* Setup DRAM control register with Disable refresh, |
| * disable write buffer Test Mode and NOP command select |
| */ |
| *drcctl=0x01; |
| |
| /* dummy write for NOP to take effect */ |
| dummy_write(); |
| print_err("NOP\n"); |
| /* 100? 200? */ |
| //sc520_udelay(100); |
| print_err("after sc520_udelay\r\n"); |
| |
| /* issue all banks precharge */ |
| *drcctl=0x02; |
| print_err("set *drcctl to 2 \r\n"); |
| dummy_write(); |
| print_err("PRE\n"); |
| |
| /* issue 2 auto refreshes to all banks */ |
| *drcctl=0x04; |
| dummy_write(); |
| print_err("AUTO1\n"); |
| dummy_write(); |
| print_err("AUTO2\n"); |
| |
| /* issue LOAD MODE REGISTER command */ |
| *drcctl=0x03; |
| dummy_write(); |
| print_err("LOAD MODE REG\n"); |
| |
| *drcctl=0x04; |
| for (i=0; i<8; i++) /* refresh 8 times */{ |
| dummy_write(); |
| print_err("dummy write\r\n"); |
| } |
| print_err("8 dummy writes\n"); |
| |
| /* set control register to NORMAL mode */ |
| *drcctl=0x00; |
| print_err("normal\n"); |
| |
| print_err("HI done normal\r\n"); |
| bank = 3; |
| |
| |
| /* this is really ugly, it is right from assembly code. |
| * we need to clean it up later |
| */ |
| |
| start: |
| /* write col 11 wrap adr */ |
| COL11_ADR=COL11_DATA; |
| if(COL11_ADR!=COL11_DATA) |
| goto bad_ram; |
| |
| print_err("11\n"); |
| /* write col 10 wrap adr */ |
| COL10_ADR=COL10_DATA; |
| if(COL10_ADR!=COL10_DATA) |
| goto bad_ram; |
| print_err("10\n"); |
| |
| /* write col 9 wrap adr */ |
| COL09_ADR=COL09_DATA; |
| if(COL09_ADR!=COL09_DATA) |
| goto bad_ram; |
| print_err("9\n"); |
| |
| /* write col 8 wrap adr */ |
| COL08_ADR=COL08_DATA; |
| if(COL08_ADR!=COL08_DATA) |
| goto bad_ram; |
| print_err("8\n"); |
| |
| /* write row 14 wrap adr */ |
| ROW14_ADR=ROW14_DATA; |
| if(ROW14_ADR!=ROW14_DATA) |
| goto bad_ram; |
| print_err("14\n"); |
| |
| /* write row 13 wrap adr */ |
| ROW13_ADR=ROW13_DATA; |
| if(ROW13_ADR!=ROW13_DATA) |
| goto bad_ram; |
| print_err("13\n"); |
| |
| /* write row 12 wrap adr */ |
| ROW12_ADR=ROW12_DATA; |
| if(ROW12_ADR!=ROW12_DATA) |
| goto bad_ram; |
| print_err("12\n"); |
| |
| /* write row 11 wrap adr */ |
| ROW11_ADR=ROW11_DATA; |
| if(ROW11_ADR!=ROW11_DATA) |
| goto bad_ram; |
| print_err("11\n"); |
| |
| /* write row 10 wrap adr */ |
| ROW10_ADR=ROW10_DATA; |
| if(ROW10_ADR!=ROW10_DATA) |
| goto bad_ram; |
| print_err("10\n"); |
| |
| /* |
| * read data @ row 12 wrap adr to determine # banks, |
| * and read data @ row 14 wrap adr to determine # rows. |
| * if data @ row 12 wrap adr is not AA, 11 or 12 we have bad RAM. |
| * if data @ row 12 wrap == AA, we only have 2 banks, NOT 4 |
| * if data @ row 12 wrap == 11 or 12, we have 4 banks |
| */ |
| |
| banks=2; |
| if (ROW12_ADR != ROW10_DATA) { |
| banks=4; |
| print_err("4b\n"); |
| if(ROW12_ADR != ROW11_DATA) { |
| if(ROW12_ADR != ROW12_DATA) |
| goto bad_ram; |
| } |
| } |
| |
| /* validate row mask */ |
| rows=ROW14_ADR; |
| if (rows<ROW11_DATA) |
| goto bad_ram; |
| if (rows>ROW14_DATA) |
| goto bad_ram; |
| /* verify all 4 bytes of dword same */ |
| /* |
| if(rows&0xffff!=(rows>>16)&0xffff) |
| goto bad_ram; |
| if(rows&0xff!=(rows>>8)&0xff) |
| goto bad_ram; |
| */ |
| /* now just get one of them */ |
| rows &= 0xff; |
| print_err("rows"); print_err_hex32(rows); print_err("\n"); |
| /* validate column data */ |
| cols=COL11_ADR; |
| if(cols<COL08_DATA) |
| goto bad_ram; |
| if (cols>COL11_DATA) |
| goto bad_ram; |
| /* verify all 4 bytes of dword same */ |
| /* |
| if(cols&0xffff!=(cols>>16)&0xffff) |
| goto bad_ram; |
| if(cols&0xff!=(cols>>8)&0xff) |
| goto bad_ram; |
| */ |
| print_err("cols"); print_err_hex32(cols); print_err("\n"); |
| cols -= COL08_DATA; |
| |
| /* cols now is in the range of 0 1 2 3 ... |
| */ |
| i = cols&3; |
| // i = cols + rows; |
| |
| /* wacky end addr calculation */ |
| /* |
| al = 3; |
| al -= (i & 0xff);k |
| */ |
| |
| /* what a fookin' mess this is */ |
| if(banks==4) |
| i+=8; /* <-- i holds merged value */ |
| /* i now has the col width in bits 0-1 and the bank count (2 or 4) |
| * in bit 3. |
| * this is the format for the drccfg register |
| */ |
| |
| /* fix ending addr mask*/ |
| /*FIXME*/ |
| /* let's just go with this to start ... see if we can get ANYWHERE */ |
| /* need to get end addr. Need to do it with the bank in mind. */ |
| /* |
| al = 3; |
| al -= i&3; |
| *drcbendaddr = rows >> al; |
| print_err("computed ending_adr = "); print_err_hex8(ending_adr); |
| print_err("\r\n"); |
| |
| */ |
| bad_reinit: |
| /* issue all banks recharge */ |
| *drcctl=0x02; |
| dummy_write(); |
| |
| /* update ending address register */ |
| // *drcbendadr = ending_adr; |
| |
| /* update config register */ |
| *drccfg &= ~(0xff << bank*4); |
| if (ending_adr) |
| *drccfg = ((banks == 4 ? 8 : 0) | cols & 3)<< (bank*4); |
| // dumpram(); |
| /* skip the rest for now */ |
| // bank = 0; |
| // *drccfg=*drccfg&YYY|ZZZZ; |
| |
| if(bank!=0) { |
| bank--; |
| // drcbendaddr--; |
| *drcbendaddr = 0xff000000; |
| //*(&*drcbendadr+XXYYXX)=0xff; |
| goto start; |
| } |
| |
| /* set control register to NORMAL mode */ |
| *drcctl=0x18; |
| dummy_write(); |
| return bank; |
| |
| bad_ram: |
| print_info("bad ram!\r\n"); |
| /* you are here because the read-after-write failed, |
| * in most cases because: no ram in that bank! |
| * set badbank to 1 and go to reinit |
| */ |
| ending_adr = 0; |
| goto bad_reinit; |
| while(1) |
| print_err("DONE NEXTBANK\r\n"); |
| #endif |
| } |
| |
| /* note: based on AMD code*/ |
| /* This code is known to work on the digital logic board and on the technologic |
| * systems ts5300 |
| */ |
| int staticmem(void) |
| { |
| volatile unsigned long *zero = (unsigned long *) CACHELINESZ; |
| |
| /* set up 0x18 .. **/ |
| *drcbendadr = 0x88; |
| *drcmctl = 0x1e; |
| *drccfg = 0x9; |
| /* nop mode */ |
| *drcctl = 0x1; |
| /* do the dummy write */ |
| *zero = 0; |
| |
| /* precharge */ |
| *drcctl = 2; |
| *zero = 0; |
| |
| /* two autorefreshes */ |
| *drcctl = 4; |
| *zero = 0; |
| print_debug("one zero out on refresh\r\n"); |
| *zero = 0; |
| print_debug("two zero out on refresh\r\n"); |
| |
| /* load mode register */ |
| *drcctl = 3; |
| *zero = 0; |
| print_debug("DONE the load mode reg\r\n"); |
| |
| /* normal mode */ |
| *drcctl = 0x0; |
| *zero = 0; |
| print_debug("DONE one last write and then turn on refresh etc\r\n"); |
| *drcctl = 0x18; |
| *zero = 0; |
| print_debug("DONE the normal\r\n"); |
| *zero = 0xdeadbeef; |
| if (*zero != 0xdeadbeef) |
| print_debug("NO LUCK\r\n"); |
| else |
| print_debug("did a store and load ...\r\n"); |
| //print_err_hex32(*zero); |
| // print_err(" zero is now "); print_err_hex32(*zero); print_err("\r\n"); |
| } |