| /* This was originally for the e7500, modified for e7501 |
| * The primary differences are that 7501 apparently can |
| * support single channel RAM (i haven't tested), |
| * CAS1.5 is no longer supported, The ECC scrubber |
| * now supports a mode to zero RAM and init ECC in one step |
| * and the undocumented registers at 0x80 require new |
| * (undocumented) values determined by guesswork and |
| * comparison w/ OEM BIOS values. |
| * Steven James 02/06/2003 |
| */ |
| |
| /* converted to C 6/2004 yhlu */ |
| |
| #include <assert.h> |
| #include <spd.h> |
| #include <sdram_mode.h> |
| #include <stdlib.h> |
| #include "e7501.h" |
| |
| /*----------------------------------------------------------------------------- |
| Definitions: |
| -----------------------------------------------------------------------------*/ |
| |
| // Uncomment this to enable run-time checking of DIMM parameters |
| // for dual-channel operation |
| // Unfortunately the code seems to chew up several K of space. |
| //#define VALIDATE_DIMM_COMPATIBILITY |
| |
| #if CONFIG_DEBUG_RAM_SETUP |
| #define RAM_DEBUG_MESSAGE(x) print_debug(x) |
| #define RAM_DEBUG_HEX32(x) print_debug_hex32(x) |
| #define RAM_DEBUG_HEX8(x) print_debug_hex8(x) |
| #define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0)) |
| #else |
| #define RAM_DEBUG_MESSAGE(x) |
| #define RAM_DEBUG_HEX32(x) |
| #define RAM_DEBUG_HEX8(x) |
| #define DUMPNORTH() |
| #endif |
| |
| #define E7501_SDRAM_MODE (SDRAM_BURST_INTERLEAVED | SDRAM_BURST_4) |
| #define SPD_ERROR "Error reading SPD info\n" |
| |
| // NOTE: This used to be 0x100000. |
| // That doesn't work on systems where A20M# is asserted, because |
| // attempts to access 0x1000NN end up accessing 0x0000NN. |
| #define RCOMP_MMIO 0x200000 |
| |
| struct dimm_size { |
| unsigned long side1; |
| unsigned long side2; |
| }; |
| |
| static const uint32_t refresh_frequency[] = { |
| /* Relative frequency (array value) of each E7501 Refresh Mode Select |
| * (RMS) value (array index) |
| * 0 == least frequent refresh (longest interval between refreshes) |
| * [0] disabled -> 0 |
| * [1] 15.6 usec -> 2 |
| * [2] 7.8 usec -> 3 |
| * [3] 64 usec -> 1 |
| * [4] reserved -> 0 |
| * [5] reserved -> 0 |
| * [6] reserved -> 0 |
| * [7] 64 clocks -> 4 |
| */ |
| 0, 2, 3, 1, 0, 0, 0, 4 |
| }; |
| |
| static const uint32_t refresh_rate_map[] = { |
| /* Map the JEDEC spd refresh rates (array index) to E7501 Refresh Mode |
| * Select values (array value) |
| * These are all the rates defined by JESD21-C Appendix D, Rev. 1.0 |
| * The E7501 supports only 15.6 us (1), 7.8 us (2), 64 us (3), and |
| * 64 clock (481 ns) (7) refresh. |
| * [0] == 15.625 us -> 15.6 us |
| * [1] == 3.9 us -> 481 ns |
| * [2] == 7.8 us -> 7.8 us |
| * [3] == 31.3 us -> 15.6 us |
| * [4] == 62.5 us -> 15.6 us |
| * [5] == 125 us -> 64 us |
| */ |
| 1, 7, 2, 1, 1, 3 |
| }; |
| |
| #define MAX_SPD_REFRESH_RATE ((sizeof(refresh_rate_map) / sizeof(uint32_t)) - 1) |
| |
| // SPD parameters that must match for dual-channel operation |
| static const uint8_t dual_channel_parameters[] = { |
| SPD_MEMORY_TYPE, |
| SPD_MODULE_VOLTAGE, |
| SPD_NUM_COLUMNS, |
| SPD_NUM_ROWS, |
| SPD_NUM_DIMM_BANKS, |
| SPD_PRIMARY_SDRAM_WIDTH, |
| SPD_NUM_BANKS_PER_SDRAM |
| }; |
| |
| /* |
| * Table: constant_register_values |
| */ |
| static const long constant_register_values[] = { |
| /* SVID - Subsystem Vendor Identification Register |
| * 0x2c - 0x2d |
| * [15:00] Subsytem Vendor ID (Indicates system board vendor) |
| */ |
| /* SID - Subsystem Identification Register |
| * 0x2e - 0x2f |
| * [15:00] Subsystem ID |
| */ |
| // Not everyone wants to be Super Micro Computer, Inc. |
| // The mainboard should set this if desired. |
| // 0x2c, 0, (0x15d9 << 0) | (0x3580 << 16), |
| |
| /* Undocumented |
| * (DRAM Read Timing Control, if similar to 855PM?) |
| * 0x80 - 0x81 |
| * This register has something to do with CAS latencies, |
| * possibily this is the real chipset control. |
| * At 0x00 CAS latency 1.5 works. |
| * At 0x06 CAS latency 2.5 works. |
| * At 0x01 CAS latency 2.0 works. |
| */ |
| /* This is still undocumented in e7501, but with different values |
| * CAS 2.0 values taken from Intel BIOS settings, others are a guess |
| * and may be terribly wrong. Old values preserved as comments until I |
| * figure this out for sure. |
| * e7501 docs claim that CAS1.5 is unsupported, so it may or may not |
| * work at all. |
| * Steven James 02/06/2003 |
| */ |
| /* NOTE: values now configured in configure_e7501_cas_latency() based |
| * on SPD info and total number of DIMMs (per Intel) |
| */ |
| |
| /* FDHC - Fixed DRAM Hole Control |
| * 0x58 |
| * [7:7] Hole_Enable |
| * 0 == No memory Hole |
| * 1 == Memory Hole from 15MB to 16MB |
| * [6:0] Reserved |
| * |
| * PAM - Programmable Attribute Map |
| * 0x59 [1:0] Reserved |
| * 0x59 [5:4] 0xF0000 - 0xFFFFF |
| * 0x5A [1:0] 0xC0000 - 0xC3FFF |
| * 0x5A [5:4] 0xC4000 - 0xC7FFF |
| * 0x5B [1:0] 0xC8000 - 0xCBFFF |
| * 0x5B [5:4] 0xCC000 - 0xCFFFF |
| * 0x5C [1:0] 0xD0000 - 0xD3FFF |
| * 0x5C [5:4] 0xD4000 - 0xD7FFF |
| * 0x5D [1:0] 0xD8000 - 0xDBFFF |
| * 0x5D [5:4] 0xDC000 - 0xDFFFF |
| * 0x5E [1:0] 0xE0000 - 0xE3FFF |
| * 0x5E [5:4] 0xE4000 - 0xE7FFF |
| * 0x5F [1:0] 0xE8000 - 0xEBFFF |
| * 0x5F [5:4] 0xEC000 - 0xEFFFF |
| * 00 == DRAM Disabled (All Access go to memory mapped I/O space) |
| * 01 == Read Only (Reads to DRAM, Writes to memory mapped I/O space) |
| * 10 == Write Only (Writes to DRAM, Reads to memory mapped I/O space) |
| * 11 == Normal (All Access go to DRAM) |
| */ |
| |
| // Map all legacy ranges to DRAM |
| 0x58, 0xcccccf7f, (0x00 << 0) | (0x30 << 8) | (0x33 << 16) | (0x33 << 24), |
| 0x5C, 0xcccccccc, (0x33 << 0) | (0x33 << 8) | (0x33 << 16) | (0x33 << 24), |
| |
| /* DRB - DRAM Row Boundary Registers |
| * 0x60 - 0x6F |
| * An array of 8 byte registers, which hold the ending |
| * memory address assigned to each pair of DIMMS, in 64MB |
| * granularity. |
| */ |
| // Conservatively say each row has 64MB of ram, we will fix this up later |
| // NOTE: These defaults allow us to prime all of the DIMMs on the board |
| // without jumping through 36-bit adddressing hoops, even if the |
| // total memory is > 4 GB. Changing these values may break do_ram_command()! |
| 0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24), |
| 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24), |
| |
| /* DRA - DRAM Row Attribute Register |
| * 0x70 Row 0,1 |
| * 0x71 Row 2,3 |
| * 0x72 Row 4,5 |
| * 0x73 Row 6,7 |
| * [7:7] Device width for Odd numbered rows |
| * 0 == 8 bits wide x8 |
| * 1 == 4 bits wide x4 |
| * [6:4] Row Attributes for Odd numbered rows |
| * 010 == 8KB (for dual-channel) |
| * 011 == 16KB (for dual-channel) |
| * 100 == 32KB (for dual-channel) |
| * 101 == 64KB (for dual-channel) |
| * Others == Reserved |
| * [3:3] Device width for Even numbered rows |
| * 0 == 8 bits wide x8 |
| * 1 == 4 bits wide x4 |
| * [2:0] Row Attributes for Even numbered rows |
| * 010 == 8KB (for dual-channel) |
| * 011 == 16KB (for dual-channel) |
| * 100 == 32KB (for dual-channel) |
| * 101 == 64KB (This page size appears broken) |
| * Others == Reserved |
| */ |
| // NOTE: overridden by configure_e7501_row_attributes(), later |
| 0x70, 0x00000000, 0, |
| |
| /* DRT - DRAM Timing Register |
| * 0x78 |
| * [31:30] Reserved |
| * [29:29] Back to Back Write-Read Turn Around |
| * 0 == 3 clocks between WR-RD commands |
| * 1 == 2 clocks between WR-RD commands |
| * [28:28] Back to Back Read-Write Turn Around |
| * 0 == 5 clocks between RD-WR commands |
| * 1 == 4 clocks between RD-WR commands |
| * [27:27] Back to Back Read Turn Around |
| * 0 == 4 clocks between RD commands |
| * 1 == 3 clocks between RD commands |
| * [26:24] Read Delay (tRD) |
| * 000 == 7 clocks |
| * 001 == 6 clocks |
| * 010 == 5 clocks |
| * Others == Reserved |
| * [23:19] Reserved |
| * [18:16] DRAM idle timer |
| * 000 == infinite |
| * 011 == 16 dram clocks |
| * 001 == 0 clocks |
| * [15:11] Reserved |
| * [10:09] Active to Precharge (tRAS) |
| * 00 == 7 clocks |
| * 01 == 6 clocks |
| * 10 == 5 clocks |
| * 11 == Reserved |
| * [08:06] Reserved |
| * [05:04] Cas Latency (tCL) |
| * 00 == 2.5 Clocks |
| * 01 == 2.0 Clocks |
| * 10 == Reserved (was 1.5 Clocks for E7500) |
| * 11 == Reserved |
| * [03:03] Write Ras# to Cas# Delay (tRCD) |
| * 0 == 3 DRAM Clocks |
| * 1 == 2 DRAM Clocks |
| * [02:01] Read RAS# to CAS# Delay (tRCD) |
| * 00 == reserved |
| * 01 == reserved |
| * 10 == 3 DRAM Clocks |
| * 11 == 2 DRAM Clocks |
| * [00:00] DRAM RAS# to Precharge (tRP) |
| * 0 == 3 DRAM Clocks |
| * 1 == 2 DRAM Clocks |
| */ |
| |
| // Some earlier settings: |
| /* Most aggressive settings possible */ |
| // 0x78, 0xc0fff8c4, (1<<29)|(1<<28)|(1<<27)|(2<<24)|(2<<9)|CAS_LATENCY|(1<<3)|(1<<1)|(1<<0), |
| // 0x78, 0xc0f8f8c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0), |
| // 0x78, 0xc0f8f9c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|CAS_LATENCY|(1<<3)|(3<<1)|(1<<0), |
| |
| // The only things we need to set here are DRAM idle timer, Back-to-Back Read Turnaround, and |
| // Back-to-Back Write-Read Turnaround. All others are configured based on SPD. |
| 0x78, 0xD7F8FFFF, (1 << 29) | (1 << 27) | (1 << 16), |
| |
| /* FIXME why was I attempting to set a reserved bit? */ |
| /* 0x0100040f */ |
| |
| /* DRC - DRAM Contoller Mode Register |
| * 0x7c |
| * [31:30] Reserved |
| * [29:29] Initialization Complete |
| * 0 == Not Complete |
| * 1 == Complete |
| * [28:23] Reserved |
| * [22:22] Channels |
| * 0 == Single channel |
| * 1 == Dual Channel |
| * [21:20] DRAM Data Integrity Mode |
| * 00 == Disabled, no ECC |
| * 01 == Reserved |
| * 10 == Error checking, using chip-kill, with correction |
| * 11 == Reserved |
| * [19:18] DRB Granularity (Read-Only) |
| * 00 == 32 MB quantities (single channel mode) |
| * 01 == 64 MB quantities (dual-channel mode) |
| * 10 == Reserved |
| * 11 == Reserved |
| * [17:17] (Intel Undocumented) should always be set to 1 (SJM: comment inconsistent with current setting, below) |
| * [16:16] Command Per Clock - Address/Control Assertion Rule (CPC) |
| * 0 == 2n Rule |
| * 1 == 1n rule |
| * [15:11] Reserved |
| * [10:08] Refresh mode select |
| * 000 == Refresh disabled |
| * 001 == Refresh interval 15.6 usec |
| * 010 == Refresh interval 7.8 usec |
| * 011 == Refresh interval 64 usec |
| * 111 == Refresh every 64 clocks (fast refresh) |
| * [07:07] Reserved |
| * [06:04] Mode Select (SMS) |
| * 000 == Reserved (was Self Refresh Mode in E7500) |
| * 001 == NOP Command |
| * 010 == All Banks Precharge |
| * 011 == Mode Register Set |
| * 100 == Extended Mode Register Set |
| * 101 == Reserved |
| * 110 == CBR Refresh |
| * 111 == Normal Operation |
| * [03:00] Reserved |
| */ |
| // .long 0x7c, 0xffcefcff, (1<<22)|(2 << 20)|(1 << 16)| (0 << 8), |
| // .long 0x7c, 0xff8cfcff, (1<<22)|(2 << 20)|(1 << 17)|(1 << 16)| (0 << 8), |
| // .long 0x7c, 0xff80fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 17)|(1 << 16)| (0 << 8), |
| |
| // Default to dual-channel mode, ECC, 1-clock address/cmd hold |
| // NOTE: configure_e7501_dram_controller_mode() configures further |
| 0x7c, 0xff8ef8ff, (1 << 22) | (2 << 20) | (1 << 16) | (0 << 8), |
| |
| /* Another Intel undocumented register |
| * 0x88 - 0x8B |
| * [31:31] Purpose unknown |
| * [26:26] Master DLL Reset? |
| * 0 == Normal operation? |
| * 1 == Reset? |
| * [07:07] Periodic memory recalibration? |
| * 0 == Disabled? |
| * 1 == Enabled? |
| * [04:04] Receive FIFO RE-Sync? |
| * 0 == Normal operation? |
| * 1 == Reset? |
| */ |
| // NOTE: Some factory BIOSs don't do this. |
| // Doesn't seem to matter either way. |
| 0x88, 0xffffff00, 0x80, |
| |
| /* CLOCK_DIS - CK/CK# Disable Register |
| * 0x8C |
| * [7:7] DDR Frequency |
| * 0 == 100 MHz (200 MHz data rate) |
| * 1 == 133 MHz (266 MHz data rate) |
| * [6:4] Reserved |
| * [3:3] CK3 |
| * 0 == Enable |
| * 1 == Disable |
| * [2:2] CK2 |
| * 0 == Enable |
| * 1 == Disable |
| * [1:1] CK1 |
| * 0 == Enable |
| * 1 == Disable |
| * [0:0] CK0 |
| * 0 == Enable |
| * 1 == Disable |
| */ |
| // NOTE: Disable all clocks initially; turn ones we need back on |
| // in enable_e7501_clocks() |
| 0x8C, 0xfffffff0, 0xf, |
| |
| /* TOLM - Top of Low Memory Register |
| * 0xC4 - 0xC5 |
| * [15:11] Top of low memory (TOLM) |
| * The address below 4GB that should be treated as RAM, |
| * on a 128MB granularity. |
| * [10:00] Reserved |
| */ |
| /* REMAPBASE - Remap Base Address Regsiter |
| * 0xC6 - 0xC7 |
| * [15:10] Reserved |
| * [09:00] Remap Base Address [35:26] 64M aligned |
| * Bits [25:0] are assumed to be 0. |
| */ |
| |
| // NOTE: TOLM overridden by configure_e7501_ram_addresses() |
| 0xc4, 0xfc0007ff, (0x2000 << 0) | (0x3ff << 16), |
| |
| /* REMAPLIMIT - Remap Limit Address Register |
| * 0xC8 - 0xC9 |
| * [15:10] Reserved |
| * [09:00] Remap Limit Address [35:26] 64M aligned |
| * When remaplimit < remapbase the remap window is disabled. |
| */ |
| 0xc8, 0xfffffc00, 0, |
| |
| /* DVNP - Device Not Present Register |
| * 0xE0 - 0xE1 |
| * [15:05] Reserved |
| * [04:04] Device 4 Function 1 Present |
| * 0 == Present |
| * 1 == Absent |
| * [03:03] Device 3 Function 1 Present |
| * 0 == Present |
| * 1 == Absent |
| * [02:02] Device 2 Function 1 Present |
| * 0 == Present |
| * 1 == Absent |
| * [01:01] Reserved |
| * [00:00] Device 0 Function 1 Present |
| * 0 == Present |
| * 1 == Absent |
| */ |
| |
| // Enable D0:D1, disable D2:F1, D3:F1, D4:F1 |
| 0xe0, 0xffffffe2, (1 << 4) | (1 << 3) | (1 << 2) | (0 << 0), |
| |
| // Undocumented |
| 0xd8, 0xffff9fff, 0x00000000, |
| |
| // Undocumented - this is pure conjecture based on similarity to 855PM |
| /* MCHTST - MCH Test Register |
| * 0xF4 - 0xF7 |
| * [31:31] Purpose unknown |
| * [30:30] Purpose unknown |
| * [29:23] Unknown - not used? |
| * [22:22] System Memory MMR Enable |
| * 0 == Disable: mem space and BAR at 0x14 are not accessible |
| * 1 == Enable: mem space and BAR at 0x14 are accessible |
| * [21:20] Purpose unknown |
| * [19:02] Unknown - not used? |
| * [01:01] D6EN (Device #6 enable) |
| * 0 == Disable |
| * 1 == Enable |
| * [00:00] Unknown - not used? |
| */ |
| |
| 0xf4, 0x3f8ffffd, 0x40300002, |
| |
| #ifdef SUSPICIOUS_LOOKING_CODE |
| // SJM: Undocumented. |
| // This will access D2:F0:0x50, is this correct?? |
| 0x1050, 0xffffffcf, 0x00000030, |
| #endif |
| }; |
| |
| /* DDR RECOMP tables */ |
| |
| // Slew table for 1x drive? |
| static const uint32_t maybe_1x_slew_table[] = { |
| 0x44332211, 0xc9776655, 0xffffffff, 0xffffffff, |
| 0x22111111, 0x55444332, 0xfffca876, 0xffffffff, |
| }; |
| |
| // Slew table for 2x drive? |
| static const uint32_t maybe_2x_slew_table[] = { |
| 0x00000000, 0x76543210, 0xffffeca8, 0xffffffff, |
| 0x21000000, 0xa8765432, 0xffffffec, 0xffffffff, |
| }; |
| |
| // Pull Up / Pull Down offset table, if analogous to IXP2800? |
| static const uint32_t maybe_pull_updown_offset_table[] = { |
| 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, |
| 0x88888888, 0x88888888, 0x88888888, 0x88888888, |
| }; |
| |
| /*----------------------------------------------------------------------------- |
| Delay functions: |
| -----------------------------------------------------------------------------*/ |
| |
| #define SLOW_DOWN_IO inb(0x80) |
| //#define SLOW_DOWN_IO udelay(40); |
| |
| /* Estimate that SLOW_DOWN_IO takes about 50&76us */ |
| /* delay for 200us */ |
| |
| #if 1 |
| static void do_delay(void) |
| { |
| int i; |
| for (i = 0; i < 16; i++) { |
| SLOW_DOWN_IO; |
| } |
| } |
| |
| #define DO_DELAY do_delay() |
| #else |
| #define DO_DELAY \ |
| udelay(200) |
| #endif |
| |
| #define EXTRA_DELAY DO_DELAY |
| |
| static void die_on_spd_error(int spd_return_value) |
| { |
| if (spd_return_value < 0) |
| die("Error reading SPD info\n"); |
| } |
| |
| /*----------------------------------------------------------------------------- |
| Serial presence detect (SPD) functions: |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Calculate the page size for each physical bank of the DIMM: |
| * log2(page size) = (# columns) + log2(data width) |
| * |
| * NOTE: Page size is the total number of data bits in a row. |
| * |
| * @param dimm_socket_address SMBus address of DIMM socket to interrogate. |
| * @return log2(page size) for each side of the DIMM. |
| */ |
| static struct dimm_size sdram_spd_get_page_size(uint16_t dimm_socket_address) |
| { |
| uint16_t module_data_width; |
| int value; |
| struct dimm_size pgsz; |
| |
| pgsz.side1 = 0; |
| pgsz.side2 = 0; |
| |
| // Side 1 |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); |
| if (value < 0) |
| goto hw_err; |
| pgsz.side1 = value & 0xf; // # columns in bank 1 |
| |
| /* Get the module data width and convert it to a power of two */ |
| value = |
| spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_MSB); |
| if (value < 0) |
| goto hw_err; |
| module_data_width = (value & 0xff) << 8; |
| |
| value = |
| spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_LSB); |
| if (value < 0) |
| goto hw_err; |
| module_data_width |= (value & 0xff); |
| |
| pgsz.side1 += log2(module_data_width); |
| |
| /* side two */ |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); |
| if (value < 0) |
| goto hw_err; |
| if (value > 2) |
| die("Bad SPD value\n"); |
| if (value == 2) { |
| |
| pgsz.side2 = pgsz.side1; // Assume symmetric banks until we know differently |
| value = |
| spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); |
| if (value < 0) |
| goto hw_err; |
| if ((value & 0xf0) != 0) { |
| // Asymmetric banks |
| pgsz.side2 -= value & 0xf; /* Subtract out columns on side 1 */ |
| pgsz.side2 += (value >> 4) & 0xf; /* Add in columns on side 2 */ |
| } |
| } |
| |
| return pgsz; |
| |
| hw_err: |
| die(SPD_ERROR); |
| return pgsz; // Never reached |
| } |
| |
| /** |
| * Read the width in bits of each DIMM side's DRAMs via SPD (i.e. 4, 8, 16). |
| * |
| * @param dimm_socket_address SMBus address of DIMM socket to interrogate. |
| * @return Width in bits of each DIMM side's DRAMs. |
| */ |
| static struct dimm_size sdram_spd_get_width(uint16_t dimm_socket_address) |
| { |
| int value; |
| struct dimm_size width; |
| |
| width.side1 = 0; |
| width.side2 = 0; |
| |
| value = |
| spd_read_byte(dimm_socket_address, SPD_PRIMARY_SDRAM_WIDTH); |
| die_on_spd_error(value); |
| |
| width.side1 = value & 0x7f; // Mask off bank 2 flag |
| |
| if (value & 0x80) { |
| width.side2 = width.side1 << 1; // Bank 2 exists and is double-width |
| } else { |
| // If bank 2 exists, it's the same width as bank 1 |
| value = |
| spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); |
| die_on_spd_error(value); |
| |
| #ifdef ROMCC_IF_BUG_FIXED |
| if (value == 2) |
| width.side2 = width.side1; |
| #else |
| switch (value) { |
| case 2: |
| width.side2 = width.side1; |
| break; |
| |
| default: |
| break; |
| } |
| #endif |
| } |
| |
| return width; |
| } |
| |
| /** |
| * Calculate the log base 2 size in bits of both DIMM sides. |
| * |
| * log2(# bits) = (# columns) + log2(data width) + |
| * (# rows) + log2(banks per SDRAM) |
| * |
| * Note that it might be easier to use SPD byte 31 here, it has the DIMM size |
| * as a multiple of 4MB. The way we do it now we can size both sides of an |
| * asymmetric DIMM. |
| * |
| * @param dimm_socket_address SMBus address of DIMM socket to interrogate. |
| * @return log2(number of bits) for each side of the DIMM. |
| */ |
| static struct dimm_size spd_get_dimm_size(unsigned dimm_socket_address) |
| { |
| int value; |
| |
| // Start with log2(page size) |
| struct dimm_size sz = sdram_spd_get_page_size(dimm_socket_address); |
| |
| if (sz.side1 > 0) { |
| |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_ROWS); |
| die_on_spd_error(value); |
| |
| sz.side1 += value & 0xf; |
| |
| if (sz.side2 > 0) { |
| |
| // Double-sided DIMM |
| if (value & 0xF0) |
| sz.side2 += value >> 4; // Asymmetric |
| else |
| sz.side2 += value; // Symmetric |
| } |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_NUM_BANKS_PER_SDRAM); |
| die_on_spd_error(value); |
| |
| value = log2(value); |
| sz.side1 += value; |
| if (sz.side2 > 0) |
| sz.side2 += value; |
| } |
| |
| return sz; |
| } |
| |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| |
| /** |
| * Determine whether two DIMMs have the same value for an SPD parameter. |
| * |
| * @param spd_byte_number The SPD byte number to compare in both DIMMs. |
| * @param dimm0_address SMBus address of the 1st DIMM socket to interrogate. |
| * @param dimm1_address SMBus address of the 2nd DIMM socket to interrogate. |
| * @return 1 if both DIMM sockets report the same value for the specified |
| * SPD parameter, 0 if the values differed or an error occurred. |
| */ |
| static uint8_t are_spd_values_equal(uint8_t spd_byte_number, |
| uint16_t dimm0_address, |
| uint16_t dimm1_address) |
| { |
| uint8_t bEqual = 0; |
| int dimm0_value = spd_read_byte(dimm0_address, spd_byte_number); |
| int dimm1_value = spd_read_byte(dimm1_address, spd_byte_number); |
| |
| if ((dimm0_value >= 0) && (dimm1_value >= 0) |
| && (dimm0_value == dimm1_value)) |
| bEqual = 1; |
| |
| return bEqual; |
| } |
| #endif |
| |
| /** |
| * Scan for compatible DIMMs. |
| * |
| * The code in this module only supports dual-channel operation, so we test |
| * that compatible DIMMs are paired. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @return A bitmask indicating which of the possible sockets for each channel |
| * was found to contain a compatible DIMM. |
| * Bit 0 corresponds to the closest socket for channel 0 |
| * Bit 1 to the next socket for channel 0 |
| * ... |
| * Bit MAX_DIMM_SOCKETS_PER_CHANNEL-1 to the last socket for channel 0 |
| * Bit MAX_DIMM_SOCKETS_PER_CHANNEL is the closest socket for channel 1 |
| * ... |
| * Bit 2*MAX_DIMM_SOCKETS_PER_CHANNEL-1 is the last socket for channel 1 |
| */ |
| static uint8_t spd_get_supported_dimms(const struct mem_controller *ctrl) |
| { |
| int i; |
| uint8_t dimm_mask = 0; |
| |
| // Have to increase size of dimm_mask if this assertion is violated |
| ASSERT(MAX_DIMM_SOCKETS_PER_CHANNEL <= 4); |
| |
| // Find DIMMs we can support on channel 0. |
| // Then see if the corresponding channel 1 DIMM has the same parameters, |
| // since we only support dual-channel. |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { |
| |
| uint16_t channel0_dimm = ctrl->channel0[i]; |
| uint16_t channel1_dimm = ctrl->channel1[i]; |
| uint8_t bDualChannel = 1; |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| struct dimm_size page_size; |
| struct dimm_size sdram_width; |
| #endif |
| int spd_value; |
| |
| if (channel0_dimm == 0) |
| continue; // No such socket on this mainboard |
| |
| if (spd_read_byte(channel0_dimm, SPD_MEMORY_TYPE) != |
| SPD_MEMORY_TYPE_SDRAM_DDR) |
| continue; |
| |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| if (spd_read_byte(channel0_dimm, SPD_MODULE_VOLTAGE) != |
| SPD_VOLTAGE_SSTL2) |
| continue; // Unsupported voltage |
| |
| // E7501 does not support unregistered DIMMs |
| spd_value = |
| spd_read_byte(channel0_dimm, SPD_MODULE_ATTRIBUTES); |
| if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) |
| continue; |
| |
| // Must support burst = 4 for dual-channel operation on E7501 |
| // NOTE: for single-channel, burst = 8 is required |
| spd_value = |
| spd_read_byte(channel0_dimm, |
| SPD_SUPPORTED_BURST_LENGTHS); |
| if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0)) |
| continue; |
| |
| page_size = sdram_spd_get_page_size(channel0_dimm); |
| sdram_width = sdram_spd_get_width(channel0_dimm); |
| |
| // Validate DIMM page size |
| // The E7501 only supports page sizes of 4, 8, 16, or 32 KB per channel |
| // NOTE: 4 KB = 32 Kb = 2^15 |
| // 32 KB = 262 Kb = 2^18 |
| |
| if ((page_size.side1 < 15) || (page_size.side1 > 18)) |
| continue; |
| |
| // If DIMM is double-sided, verify side2 page size |
| if (page_size.side2 != 0) { |
| if ((page_size.side2 < 15) |
| || (page_size.side2 > 18)) |
| continue; |
| } |
| // Validate SDRAM width |
| // The E7501 only supports x4 and x8 devices |
| |
| if ((sdram_width.side1 != 4) && (sdram_width.side1 != 8)) |
| continue; |
| |
| // If DIMM is double-sided, verify side2 width |
| if (sdram_width.side2 != 0) { |
| if ((sdram_width.side2 != 4) |
| && (sdram_width.side2 != 8)) |
| continue; |
| } |
| #endif |
| // Channel 0 DIMM looks compatible. |
| // Now see if it is paired with the proper DIMM on channel 1. |
| |
| ASSERT(channel1_dimm != 0); // No such socket on this mainboard?? |
| |
| // NOTE: unpopulated DIMMs cause read to fail |
| spd_value = |
| spd_read_byte(channel1_dimm, SPD_MODULE_ATTRIBUTES); |
| if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) { |
| |
| print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n"); |
| continue; |
| } |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| spd_value = |
| spd_read_byte(channel1_dimm, |
| SPD_SUPPORTED_BURST_LENGTHS); |
| if (!(spd_value & SPD_BURST_LENGTH_4) || (spd_value < 0)) |
| continue; |
| |
| int j; |
| for (j = 0; j < sizeof(dual_channel_parameters); ++j) { |
| if (!are_spd_values_equal |
| (dual_channel_parameters[j], channel0_dimm, |
| channel1_dimm)) { |
| |
| bDualChannel = 0; |
| break; |
| } |
| } |
| #endif |
| |
| // Code around ROMCC bug in optimization of "if" statements |
| #ifdef ROMCC_IF_BUG_FIXED |
| if (bDualChannel) { |
| // Made it through all the checks, this DIMM pair is usable |
| dimm_mask |= ((1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i))); |
| } else |
| print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n"); |
| #else |
| switch (bDualChannel) { |
| case 0: |
| print_debug("Skipping un-matched DIMMs - only dual-channel operation supported\n"); |
| break; |
| |
| default: |
| // Made it through all the checks, this DIMM pair is usable |
| dimm_mask |= (1 << i) | (1 << (MAX_DIMM_SOCKETS_PER_CHANNEL + i)); |
| break; |
| } |
| #endif |
| } |
| |
| return dimm_mask; |
| } |
| |
| /*----------------------------------------------------------------------------- |
| SDRAM configuration functions: |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Send the specified command to all DIMMs. |
| * |
| * @param command Specifies the command to be sent to the DIMMs. |
| * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the |
| * register value in JEDEC format. |
| */ |
| static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits) |
| { |
| int i; |
| uint32_t dram_controller_mode; |
| uint8_t dimm_start_64M_multiple = 0; |
| uint16_t e7501_mode_bits = jedec_mode_bits; |
| |
| // Configure the RAM command |
| dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); |
| dram_controller_mode &= 0xFFFFFF8F; |
| dram_controller_mode |= command; |
| pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); |
| |
| // RAM_COMMAND_NORMAL is an exception. |
| // It affects only the memory controller and does not need to be "sent" to the DIMMs. |
| |
| if (command != RAM_COMMAND_NORMAL) { |
| |
| // Send the command to all DIMMs by accessing a memory location within each |
| // NOTE: for mode select commands, some of the location address bits |
| // are part of the command |
| |
| // Map JEDEC mode bits to E7501 |
| if (command == RAM_COMMAND_MRS) { |
| // Host address lines [15:5] map to DIMM address lines [12:11, 9:1] |
| // The E7501 hard-sets DIMM address lines 10 & 0 to zero |
| |
| ASSERT(!(jedec_mode_bits & 0x0401)); |
| |
| e7501_mode_bits = ((jedec_mode_bits & 0x1800) << (15 - 12)) | // JEDEC bits 11-12 move to bits 14-15 |
| ((jedec_mode_bits & 0x03FE) << (13 - 9)); // JEDEC bits 1-9 move to bits 5-13 |
| |
| } else if (command == RAM_COMMAND_EMRS) { |
| // Host address lines [15:3] map to DIMM address lines [12:0] |
| e7501_mode_bits = jedec_mode_bits <<= 3; |
| } else |
| ASSERT(jedec_mode_bits == 0); |
| |
| dimm_start_64M_multiple = 0; |
| |
| for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) { |
| |
| uint8_t dimm_end_64M_multiple = |
| pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i); |
| if (dimm_end_64M_multiple > dimm_start_64M_multiple) { |
| |
| // This code assumes DRAM row boundaries are all set below 4 GB |
| // NOTE: 0x40 * 64 MB == 4 GB |
| ASSERT(dimm_start_64M_multiple < 0x40); |
| |
| // NOTE: 2^26 == 64 MB |
| |
| uint32_t dimm_start_address = |
| dimm_start_64M_multiple << 26; |
| |
| RAM_DEBUG_MESSAGE(" Sending RAM command to 0x"); |
| RAM_DEBUG_HEX32(dimm_start_address + e7501_mode_bits); |
| RAM_DEBUG_MESSAGE("\n"); |
| |
| read32(dimm_start_address + e7501_mode_bits); |
| |
| // Set the start of the next DIMM |
| dimm_start_64M_multiple = |
| dimm_end_64M_multiple; |
| } |
| } |
| } |
| } |
| |
| /** |
| * Set the mode register of all DIMMs. |
| * |
| * The proper CAS# latency setting is added to the mode bits specified |
| * by the caller. |
| * |
| * @param jedec_mode_bits For the MRS & EMRS commands, bits 0-12 contain the |
| * register value in JEDEC format. |
| */ |
| static void set_ram_mode(uint16_t jedec_mode_bits) |
| { |
| ASSERT(!(jedec_mode_bits & SDRAM_CAS_MASK)); |
| |
| uint32_t dram_cas_latency = |
| pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; |
| |
| switch (dram_cas_latency) { |
| case DRT_CAS_2_5: |
| jedec_mode_bits |= SDRAM_CAS_2_5; |
| break; |
| |
| case DRT_CAS_2_0: |
| jedec_mode_bits |= SDRAM_CAS_2_0; |
| break; |
| |
| default: |
| BUG(); |
| break; |
| } |
| |
| do_ram_command(RAM_COMMAND_MRS, jedec_mode_bits); |
| } |
| |
| /*----------------------------------------------------------------------------- |
| DIMM-independant configuration functions: |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Configure the E7501's DRAM Row Boundary (DRB) registers for the memory |
| * present in the specified DIMM. |
| * |
| * @param dimm_log2_num_bits Specifies log2(number of bits) for each side of |
| * the DIMM. |
| * @param total_dram_64M_multiple Total DRAM in the system (as a multiple of |
| * 64 MB) for DIMMs < dimm_index. |
| * @param dimm_index Which DIMM pair is being processed |
| * (0..MAX_DIMM_SOCKETS_PER_CHANNEL). |
| * @return New multiple of 64 MB total DRAM in the system. |
| */ |
| static uint8_t configure_dimm_row_boundaries(struct dimm_size dimm_log2_num_bits, uint8_t total_dram_64M_multiple, unsigned dimm_index) |
| { |
| int i; |
| |
| ASSERT(dimm_index < MAX_DIMM_SOCKETS_PER_CHANNEL); |
| |
| // DIMM sides must be at least 32 MB |
| ASSERT(dimm_log2_num_bits.side1 >= 28); |
| ASSERT((dimm_log2_num_bits.side2 == 0) |
| || (dimm_log2_num_bits.side2 >= 28)); |
| |
| // In dual-channel mode, we are called only once for each pair of DIMMs. |
| // Each time we process twice the capacity of a single DIMM. |
| |
| // Convert single DIMM capacity to paired DIMM capacity |
| // (multiply by two ==> add 1 to log2) |
| dimm_log2_num_bits.side1++; |
| if (dimm_log2_num_bits.side2 > 0) |
| dimm_log2_num_bits.side2++; |
| |
| // Add the capacity of side 1 this DIMM pair (as a multiple of 64 MB) |
| // to the total capacity of the system |
| // NOTE: 64 MB == 512 Mb, and log2(512 Mb) == 29 |
| |
| total_dram_64M_multiple += (1 << (dimm_log2_num_bits.side1 - 29)); |
| |
| // Configure the boundary address for the row on side 1 |
| pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (dimm_index << 1), |
| total_dram_64M_multiple); |
| |
| // If the DIMMs are double-sided, add the capacity of side 2 this DIMM pair |
| // (as a multiple of 64 MB) to the total capacity of the system |
| if (dimm_log2_num_bits.side2 >= 29) |
| total_dram_64M_multiple += |
| (1 << (dimm_log2_num_bits.side2 - 29)); |
| |
| // Configure the boundary address for the row (if any) on side 2 |
| pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (dimm_index << 1), |
| total_dram_64M_multiple); |
| |
| // Update boundaries for rows subsequent to these. |
| // These settings will be overridden by a subsequent call if a populated physical slot exists |
| |
| for (i = dimm_index + 1; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { |
| pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (i << 1), |
| total_dram_64M_multiple); |
| pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (i << 1), |
| total_dram_64M_multiple); |
| } |
| |
| return total_dram_64M_multiple; |
| } |
| |
| /** |
| * Set the E7501's DRAM row boundary addresses & its Top Of Low Memory (TOLM). |
| * |
| * If necessary, set up a remap window so we don't waste DRAM that ordinarily |
| * would lie behind addresses reserved for memory-mapped I/O. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). |
| */ |
| static void configure_e7501_ram_addresses(const struct mem_controller |
| *ctrl, uint8_t dimm_mask) |
| { |
| int i; |
| uint8_t total_dram_64M_multiple = 0; |
| |
| // Configure the E7501's DRAM row boundaries |
| // Start by zeroing out the temporary initial configuration |
| pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_0, 0); |
| pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_4, 0); |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { |
| |
| uint16_t dimm_socket_address = ctrl->channel0[i]; |
| struct dimm_size sz; |
| |
| if (!(dimm_mask & (1 << i))) |
| continue; // This DIMM not present |
| |
| sz = spd_get_dimm_size(dimm_socket_address); |
| |
| RAM_DEBUG_MESSAGE("dimm size ="); |
| RAM_DEBUG_HEX32((u32)sz.side1); |
| RAM_DEBUG_MESSAGE(" "); |
| RAM_DEBUG_HEX32((u32)sz.side2); |
| RAM_DEBUG_MESSAGE("\n"); |
| |
| if (sz.side1 == 0) |
| die("Bad SPD value\n"); |
| |
| total_dram_64M_multiple = |
| configure_dimm_row_boundaries(sz, total_dram_64M_multiple, i); |
| } |
| |
| // Configure the Top Of Low Memory (TOLM) in the E7501 |
| // This address must be a multiple of 128 MB that is less than 4 GB. |
| // NOTE: 16-bit wide TOLM register stores only the highest 5 bits of a 32-bit address |
| // in the highest 5 bits. |
| |
| // We set TOLM to the smaller of 0xC0000000 (3 GB) or the total DRAM in the system. |
| // This reserves addresses from 0xC0000000 - 0xFFFFFFFF for non-DRAM purposes |
| // such as flash and memory-mapped I/O. |
| |
| // If there is more than 3 GB of DRAM, we define a remap window which |
| // makes the DRAM "behind" the reserved region available above the top of physical |
| // memory. |
| |
| // NOTE: 0xC0000000 / (64 MB) == 0x30 |
| |
| if (total_dram_64M_multiple <= 0x30) { |
| |
| // <= 3 GB total RAM |
| |
| /* I should really adjust all of this in C after I have resources |
| * to all of the pci devices. |
| */ |
| |
| // Round up to 128MB granularity |
| // SJM: Is "missing" 64 MB of memory a potential issue? Should this round down? |
| |
| uint8_t total_dram_128M_multiple = |
| (total_dram_64M_multiple + 1) >> 1; |
| |
| // Convert to high 16 bits of address |
| uint16_t top_of_low_memory = |
| total_dram_128M_multiple << 11; |
| |
| pci_write_config16(PCI_DEV(0, 0, 0), TOLM, |
| top_of_low_memory); |
| |
| } else { |
| |
| // > 3 GB total RAM |
| |
| // Set defaults for > 4 GB DRAM, i.e. remap a 1 GB (= 0x10 * 64 MB) range of memory |
| uint16_t remap_base = total_dram_64M_multiple; // A[25:0] == 0 |
| uint16_t remap_limit = total_dram_64M_multiple + 0x10 - 1; // A[25:0] == 0xF |
| |
| // Put TOLM at 3 GB |
| |
| pci_write_config16(PCI_DEV(0, 0, 0), TOLM, 0xc000); |
| |
| // Define a remap window to make the RAM that would appear from 3 GB - 4 GB |
| // visible just beyond 4 GB or the end of physical memory, whichever is larger |
| // NOTE: 16-bit wide REMAP registers store only the highest 10 bits of a 36-bit address, |
| // (i.e. a multiple of 64 MB) in the lowest 10 bits. |
| // NOTE: 0x100000000 / (64 MB) == 0x40 |
| |
| if (total_dram_64M_multiple < 0x40) { |
| remap_base = 0x40; // 0x100000000 |
| remap_limit = |
| 0x40 + (total_dram_64M_multiple - 0x30) - 1; |
| } |
| |
| pci_write_config16(PCI_DEV(0, 0, 0), REMAPBASE, |
| remap_base); |
| pci_write_config16(PCI_DEV(0, 0, 0), REMAPLIMIT, |
| remap_limit); |
| } |
| } |
| |
| /** |
| * If we're configured to use ECC, initialize the SDRAM and clear the E7501's |
| * ECC error flags. |
| */ |
| static void initialize_ecc(void) |
| { |
| uint32_t dram_controller_mode; |
| |
| /* Test to see if ECC support is enabled */ |
| dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); |
| dram_controller_mode >>= 20; |
| dram_controller_mode &= 3; |
| if (dram_controller_mode == 2) { |
| |
| uint8_t byte; |
| |
| RAM_DEBUG_MESSAGE("Initializing ECC state...\n"); |
| /* Initialize ECC bits , use ECC zero mode (new to 7501) */ |
| pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x06); |
| pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x07); |
| |
| // Wait for scrub cycle to complete |
| do { |
| byte = |
| pci_read_config8(PCI_DEV(0, 0, 0), MCHCFGNS); |
| } while ((byte & 0x08) == 0); |
| |
| pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, byte & 0xfc); |
| RAM_DEBUG_MESSAGE("ECC state initialized.\n"); |
| |
| /* Clear the ECC error bits */ |
| pci_write_config8(PCI_DEV(0, 0, 1), DRAM_FERR, 0x03); |
| pci_write_config8(PCI_DEV(0, 0, 1), DRAM_NERR, 0x03); |
| |
| // Clear DRAM Interface error bits (write-one-clear) |
| pci_write_config32(PCI_DEV(0, 0, 1), FERR_GLOBAL, 1 << 18); |
| pci_write_config32(PCI_DEV(0, 0, 1), NERR_GLOBAL, 1 << 18); |
| |
| // Start normal ECC scrub |
| pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 5); |
| } |
| |
| } |
| |
| /** |
| * Program the DRAM Timing register (DRT) of the E7501 (except for CAS# |
| * latency, which is assumed to have been programmed already), based on the |
| * parameters of the various installed DIMMs. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). |
| */ |
| static void configure_e7501_dram_timing(const struct mem_controller *ctrl, |
| uint8_t dimm_mask) |
| { |
| int i; |
| uint32_t dram_timing; |
| int value; |
| uint8_t slowest_row_precharge = 0; |
| uint8_t slowest_ras_cas_delay = 0; |
| uint8_t slowest_active_to_precharge_delay = 0; |
| uint32_t current_cas_latency = |
| pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; |
| |
| // CAS# latency must be programmed beforehand |
| ASSERT((current_cas_latency == DRT_CAS_2_0) |
| || (current_cas_latency == DRT_CAS_2_5)); |
| |
| // Each timing parameter is determined by the slowest DIMM |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS; i++) { |
| uint16_t dimm_socket_address; |
| |
| if (!(dimm_mask & (1 << i))) |
| continue; // This DIMM not present |
| |
| if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) |
| dimm_socket_address = ctrl->channel0[i]; |
| else |
| dimm_socket_address = |
| ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL]; |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_MIN_ROW_PRECHARGE_TIME); |
| if (value < 0) |
| goto hw_err; |
| if (value > slowest_row_precharge) |
| slowest_row_precharge = value; |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_MIN_RAS_TO_CAS_DELAY); |
| if (value < 0) |
| goto hw_err; |
| if (value > slowest_ras_cas_delay) |
| slowest_ras_cas_delay = value; |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY); |
| if (value < 0) |
| goto hw_err; |
| if (value > slowest_active_to_precharge_delay) |
| slowest_active_to_precharge_delay = value; |
| } |
| |
| // NOTE for timing parameters: |
| // At 133 MHz, 1 clock == 7.52 ns |
| |
| /* Read the initial state */ |
| dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); |
| |
| /* Trp */ |
| |
| // E7501 supports only 2 or 3 clocks for tRP |
| if (slowest_row_precharge > ((22 << 2) | (2 << 0))) |
| die("unsupported DIMM tRP"); // > 22.5 ns: 4 or more clocks |
| else if (slowest_row_precharge > (15 << 2)) |
| dram_timing &= ~(1 << 0); // > 15.0 ns: 3 clocks |
| else |
| dram_timing |= (1 << 0); // <= 15.0 ns: 2 clocks |
| |
| /* Trcd */ |
| |
| // E7501 supports only 2 or 3 clocks for tRCD |
| // Use the same value for both read & write |
| dram_timing &= ~((1 << 3) | (3 << 1)); |
| if (slowest_ras_cas_delay > ((22 << 2) | (2 << 0))) |
| die("unsupported DIMM tRCD"); // > 22.5 ns: 4 or more clocks |
| else if (slowest_ras_cas_delay > (15 << 2)) |
| dram_timing |= (2 << 1); // > 15.0 ns: 3 clocks |
| else |
| dram_timing |= ((1 << 3) | (3 << 1)); // <= 15.0 ns: 2 clocks |
| |
| /* Tras */ |
| |
| // E7501 supports only 5, 6, or 7 clocks for tRAS |
| // 5 clocks ~= 37.6 ns, 6 clocks ~= 45.1 ns, 7 clocks ~= 52.6 ns |
| dram_timing &= ~(3 << 9); |
| |
| if (slowest_active_to_precharge_delay > 52) |
| die("unsupported DIMM tRAS"); // > 52 ns: 8 or more clocks |
| else if (slowest_active_to_precharge_delay > 45) |
| dram_timing |= (0 << 9); // 46-52 ns: 7 clocks |
| else if (slowest_active_to_precharge_delay > 37) |
| dram_timing |= (1 << 9); // 38-45 ns: 6 clocks |
| else |
| dram_timing |= (2 << 9); // < 38 ns: 5 clocks |
| |
| /* Trd */ |
| |
| /* Set to a 7 clock read delay. This is for 133Mhz |
| * with a CAS latency of 2.5 if 2.0 a 6 clock |
| * delay is good */ |
| |
| dram_timing &= ~(7 << 24); // 7 clocks |
| if (current_cas_latency == DRT_CAS_2_0) |
| dram_timing |= (1 << 24); // 6 clocks |
| |
| /* |
| * Back to Back Read-Write Turn Around |
| */ |
| /* Set to a 5 clock back to back read to write turn around. |
| * 4 is a good delay if the CAS latency is 2.0 */ |
| |
| dram_timing &= ~(1 << 28); // 5 clocks |
| if (current_cas_latency == DRT_CAS_2_0) |
| dram_timing |= (1 << 28); // 4 clocks |
| |
| pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); |
| |
| return; |
| |
| hw_err: |
| die(SPD_ERROR); |
| } |
| |
| /** |
| * Determine the shortest CAS# latency that the E7501 and all DIMMs have in |
| * common, and program the E7501 to use it. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). |
| */ |
| static void configure_e7501_cas_latency(const struct mem_controller *ctrl, |
| uint8_t dimm_mask) |
| { |
| int i; |
| int value; |
| uint32_t dram_timing; |
| uint16_t maybe_dram_read_timing; |
| uint32_t dword; |
| |
| // CAS# latency bitmasks in SPD_ACCEPTABLE_CAS_LATENCIES format |
| // NOTE: E7501 supports only 2.0 and 2.5 |
| uint32_t system_compatible_cas_latencies = |
| SPD_CAS_LATENCY_2_0 | SPD_CAS_LATENCY_2_5; |
| uint32_t current_cas_latency; |
| uint32_t dimm_compatible_cas_latencies; |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS; i++) { |
| |
| uint16_t dimm_socket_address; |
| |
| if (!(dimm_mask & (1 << i))) |
| continue; // This DIMM not usable |
| |
| if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) |
| dimm_socket_address = ctrl->channel0[i]; |
| else |
| dimm_socket_address = |
| ctrl->channel1[i - MAX_DIMM_SOCKETS_PER_CHANNEL]; |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_ACCEPTABLE_CAS_LATENCIES); |
| if (value < 0) |
| goto hw_err; |
| |
| dimm_compatible_cas_latencies = value & 0x7f; // Start with all supported by DIMM |
| current_cas_latency = 1 << log2(dimm_compatible_cas_latencies); // Max supported by DIMM |
| |
| // Can we support the highest CAS# latency? |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_MIN_CYCLE_TIME_AT_CAS_MAX); |
| if (value < 0) |
| goto hw_err; |
| |
| // NOTE: At 133 MHz, 1 clock == 7.52 ns |
| if (value > 0x75) { |
| // Our bus is too fast for this CAS# latency |
| // Remove it from the bitmask of those supported by the DIMM that are compatible |
| dimm_compatible_cas_latencies &= ~current_cas_latency; |
| } |
| // Can we support the next-highest CAS# latency (max - 0.5)? |
| |
| current_cas_latency >>= 1; |
| if (current_cas_latency != 0) { |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_SDRAM_CYCLE_TIME_2ND); |
| if (value < 0) |
| goto hw_err; |
| if (value > 0x75) |
| dimm_compatible_cas_latencies &= |
| ~current_cas_latency; |
| } |
| // Can we support the next-highest CAS# latency (max - 1.0)? |
| current_cas_latency >>= 1; |
| if (current_cas_latency != 0) { |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_SDRAM_CYCLE_TIME_3RD); |
| if (value < 0) |
| goto hw_err; |
| if (value > 0x75) |
| dimm_compatible_cas_latencies &= |
| ~current_cas_latency; |
| } |
| // Restrict the system to CAS# latencies compatible with this DIMM |
| system_compatible_cas_latencies &= |
| dimm_compatible_cas_latencies; |
| |
| /* go to the next DIMM */ |
| } |
| |
| /* After all of the arduous calculation setup with the fastest |
| * cas latency I can use. |
| */ |
| |
| dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); |
| dram_timing &= ~(DRT_CAS_MASK); |
| |
| maybe_dram_read_timing = |
| pci_read_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL); |
| maybe_dram_read_timing &= 0xF00C; |
| |
| if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) { |
| dram_timing |= DRT_CAS_2_0; |
| maybe_dram_read_timing |= 0xBB1; |
| } else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) { |
| |
| uint32_t dram_row_attributes = |
| pci_read_config32(PCI_DEV(0, 0, 0), DRA); |
| |
| dram_timing |= DRT_CAS_2_5; |
| |
| // At CAS# 2.5, DRAM Read Timing (if that's what it its) appears to need a slightly |
| // different value if all DIMM slots are populated |
| |
| if ((dram_row_attributes & 0xff) |
| && (dram_row_attributes & 0xff00) |
| && (dram_row_attributes & 0xff0000) |
| && (dram_row_attributes & 0xff000000)) { |
| |
| // All slots populated |
| maybe_dram_read_timing |= 0x0882; |
| } else { |
| // Some unpopulated slots |
| maybe_dram_read_timing |= 0x0662; |
| } |
| } else |
| die("No CAS# latencies compatible with all DIMMs!!\n"); |
| |
| pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); |
| |
| /* set master DLL reset */ |
| dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); |
| dword |= (1 << 26); |
| pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); |
| |
| dword &= 0x0c0007ff; /* patch try register 88 is undocumented tnz */ |
| dword |= 0xd2109800; |
| |
| pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); |
| |
| pci_write_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL, |
| maybe_dram_read_timing); |
| |
| dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); /* reset master DLL reset */ |
| dword &= ~(1 << 26); |
| pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); |
| |
| return; |
| |
| hw_err: |
| die(SPD_ERROR); |
| } |
| |
| /** |
| * Configure the refresh interval so that we refresh no more often than |
| * required by the "most needy" DIMM. Also disable ECC if any of the DIMMs |
| * don't support it. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). |
| */ |
| static void configure_e7501_dram_controller_mode(const struct |
| mem_controller *ctrl, |
| uint8_t dimm_mask) |
| { |
| int i; |
| |
| // Initial settings |
| uint32_t controller_mode = |
| pci_read_config32(PCI_DEV(0, 0, 0), DRC); |
| uint32_t system_refresh_mode = (controller_mode >> 8) & 7; |
| |
| // Code below assumes that most aggressive settings are in |
| // force when we are called, either via E7501 reset defaults |
| // or by sdram_set_registers(): |
| // - ECC enabled |
| // - No refresh |
| |
| ASSERT((controller_mode & (3 << 20)) == (2 << 20)); // ECC |
| ASSERT(!(controller_mode & (7 << 8))); // Refresh |
| |
| /* Walk through _all_ dimms and find the least-common denominator for: |
| * - ECC support |
| * - refresh rates |
| */ |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS; i++) { |
| |
| uint32_t dimm_refresh_mode; |
| int value; |
| uint16_t dimm_socket_address; |
| |
| if (!(dimm_mask & (1 << i))) { |
| continue; // This DIMM not usable |
| } |
| |
| if (i < MAX_DIMM_SOCKETS_PER_CHANNEL) |
| dimm_socket_address = ctrl->channel0[i]; |
| else |
| dimm_socket_address = |
| ctrl->channel1[i - |
| MAX_DIMM_SOCKETS_PER_CHANNEL]; |
| |
| // Disable ECC mode if any one of the DIMMs does not support ECC |
| // SJM: Should we just die here? E7501 datasheet says non-ECC DIMMs aren't supported. |
| |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_DIMM_CONFIG_TYPE); |
| die_on_spd_error(value); |
| if (value != ERROR_SCHEME_ECC) { |
| controller_mode &= ~(3 << 20); |
| } |
| |
| value = spd_read_byte(dimm_socket_address, SPD_REFRESH); |
| die_on_spd_error(value); |
| value &= 0x7f; // Mask off self-refresh bit |
| if (value > MAX_SPD_REFRESH_RATE) { |
| print_err("unsupported refresh rate\n"); |
| continue; |
| } |
| // Get the appropriate E7501 refresh mode for this DIMM |
| dimm_refresh_mode = refresh_rate_map[value]; |
| if (dimm_refresh_mode > 7) { |
| print_err("unsupported refresh rate\n"); |
| continue; |
| } |
| // If this DIMM requires more frequent refresh than others, |
| // update the system setting |
| if (refresh_frequency[dimm_refresh_mode] > |
| refresh_frequency[system_refresh_mode]) |
| system_refresh_mode = dimm_refresh_mode; |
| |
| #ifdef SUSPICIOUS_LOOKING_CODE |
| // SJM NOTE: This code doesn't look right. SPD values are an order of magnitude smaller |
| // than the clock period of the memory controller. Also, no other northbridge |
| // looks at SPD_CMD_SIGNAL_INPUT_HOLD_TIME. |
| |
| // Switch to 2 clocks for address/command if required by any one of the DIMMs |
| // NOTE: At 133 MHz, 1 clock == 7.52 ns |
| value = |
| spd_read_byte(dimm_socket_address, |
| SPD_CMD_SIGNAL_INPUT_HOLD_TIME); |
| die_on_spd_error(value); |
| if (value >= 0xa0) { /* At 133MHz this constant should be 0x75 */ |
| controller_mode &= ~(1 << 16); /* Use two clock cyles instead of one */ |
| } |
| #endif |
| |
| /* go to the next DIMM */ |
| } |
| |
| controller_mode |= (system_refresh_mode << 8); |
| |
| // Configure the E7501 |
| pci_write_config32(PCI_DEV(0, 0, 0), DRC, controller_mode); |
| } |
| |
| /** |
| * Configure the E7501's DRAM Row Attributes (DRA) registers based on DIMM |
| * parameters read via SPD. This tells the controller the width of the SDRAM |
| * chips on each DIMM side (x4 or x8) and the page size of each DIMM side |
| * (4, 8, 16, or 32 KB). |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| * @param dimm_mask Bitmask of populated DIMMs, spd_get_supported_dimms(). |
| */ |
| static void configure_e7501_row_attributes(const struct mem_controller |
| *ctrl, uint8_t dimm_mask) |
| { |
| int i; |
| uint32_t row_attributes = 0; |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { |
| |
| uint16_t dimm_socket_address = ctrl->channel0[i]; |
| struct dimm_size page_size; |
| struct dimm_size sdram_width; |
| |
| if (!(dimm_mask & (1 << i))) |
| continue; // This DIMM not usable |
| |
| // Get the relevant parameters via SPD |
| page_size = sdram_spd_get_page_size(dimm_socket_address); |
| sdram_width = sdram_spd_get_width(dimm_socket_address); |
| |
| // Update the DRAM Row Attributes. |
| // Page size is encoded as log2(page size in bits) - log2(8 Kb) |
| // NOTE: 8 Kb = 2^13 |
| row_attributes |= (page_size.side1 - 13) << (i << 3); // Side 1 of each DIMM is an EVEN row |
| |
| if (sdram_width.side2 > 0) |
| row_attributes |= (page_size.side2 - 13) << ((i << 3) + 4); // Side 2 is ODD |
| |
| // Set x4 flags if appropriate |
| if (sdram_width.side1 == 4) { |
| row_attributes |= 0x08 << (i << 3); |
| } |
| |
| if (sdram_width.side2 == 4) { |
| row_attributes |= 0x08 << ((i << 3) + 4); |
| } |
| |
| /* go to the next DIMM */ |
| } |
| |
| /* Write the new row attributes register */ |
| pci_write_config32(PCI_DEV(0, 0, 0), DRA, row_attributes); |
| } |
| |
| /* |
| * Enable clock signals for populated DIMM sockets and disable them for |
| * unpopulated sockets (to reduce EMI). |
| * |
| * @param dimm_mask Bitmask of populated DIMMs, see spd_get_supported_dimms(). |
| */ |
| static void enable_e7501_clocks(uint8_t dimm_mask) |
| { |
| int i; |
| uint8_t clock_disable = pci_read_config8(PCI_DEV(0, 0, 0), CKDIS); |
| |
| for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { |
| |
| uint8_t socket_mask = 1 << i; |
| |
| if (dimm_mask & socket_mask) |
| clock_disable &= ~socket_mask; // DIMM present, enable clock |
| else |
| clock_disable |= socket_mask; // DIMM absent, disable clock |
| } |
| |
| pci_write_config8(PCI_DEV(0, 0, 0), CKDIS, clock_disable); |
| } |
| |
| /* DIMM-dedependent configuration functions */ |
| |
| /** |
| * DDR Receive FIFO RE-Sync (?) |
| */ |
| static void RAM_RESET_DDR_PTR(void) |
| { |
| uint8_t byte; |
| byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); |
| byte |= (1 << 4); |
| pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); |
| |
| byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); |
| byte &= ~(1 << 4); |
| pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); |
| } |
| |
| /** |
| * Set E7501 registers that are either independent of DIMM specifics, or |
| * establish default settings that will be overridden when we learn the |
| * specifics. |
| * |
| * This sets PCI configuration registers to known good values based on the |
| * table 'constant_register_values', which are a triple of configuration |
| * register offset, mask, and bits to set. |
| */ |
| static void ram_set_d0f0_regs(void) |
| { |
| int i; |
| int num_values = ARRAY_SIZE(constant_register_values); |
| |
| ASSERT((num_values % 3) == 0); // Bad table? |
| |
| for (i = 0; i < num_values; i += 3) { |
| |
| uint32_t register_offset = constant_register_values[i]; |
| uint32_t bits_to_mask = constant_register_values[i + 1]; |
| uint32_t bits_to_set = constant_register_values[i + 2]; |
| uint32_t register_value; |
| |
| // It's theoretically possible to set values for something other than D0:F0, |
| // but it's not typically done here |
| ASSERT(!(register_offset & 0xFFFFFF00)); |
| |
| // bits_to_mask and bits_to_set should not reference the same bits |
| // Again, not strictly an error, but flagged as a potential bug |
| ASSERT((bits_to_mask & bits_to_set) == 0); |
| |
| register_value = |
| pci_read_config32(PCI_DEV(0, 0, 0), register_offset); |
| register_value &= bits_to_mask; |
| register_value |= bits_to_set; |
| |
| pci_write_config32(PCI_DEV(0, 0, 0), register_offset, |
| register_value); |
| } |
| } |
| |
| /** |
| * Copy 64 bytes from one location to another. |
| * |
| * @param src_addr TODO |
| * @param dst_addr TODO |
| */ |
| static void write_8dwords(const uint32_t *src_addr, uint32_t dst_addr) |
| { |
| int i; |
| for (i = 0; i < 8; i++) { |
| write32(dst_addr, *src_addr); |
| src_addr++; |
| dst_addr += sizeof(uint32_t); |
| } |
| } |
| |
| /** |
| * Set the E7501's (undocumented) RCOMP registers. |
| * |
| * Per the 855PM datasheet and IXP2800 HW Initialization Reference Manual, |
| * RCOMP registers appear to affect drive strength, pullup/pulldown offset, |
| * and slew rate of various signal groups. |
| * |
| * Comments below are conjecture based on apparent similarity between the |
| * E7501 and these two chips. |
| */ |
| static void ram_set_rcomp_regs(void) |
| { |
| uint32_t dword; |
| uint8_t maybe_strength_control; |
| |
| RAM_DEBUG_MESSAGE("Setting RCOMP registers.\n"); |
| |
| /*enable access to the rcomp bar */ |
| dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); |
| dword |= (1 << 22); |
| pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); |
| |
| // Set the RCOMP MMIO base address |
| pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, RCOMP_MMIO); |
| |
| // Block RCOMP updates while we configure the registers |
| dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); |
| dword |= (1 << 9); |
| write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); |
| |
| /* Begin to write the RCOMP registers */ |
| |
| // Set CMD and DQ/DQS strength to 2x (?) |
| maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0x88; |
| maybe_strength_control |= 0x44; |
| write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control); |
| |
| write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x80); |
| write16(RCOMP_MMIO + 0x42, 0); |
| |
| write_8dwords(maybe_1x_slew_table, RCOMP_MMIO + 0x60); |
| |
| // NOTE: some factory BIOS set 0x9088 here. Seems to work either way. |
| write16(RCOMP_MMIO + 0x40, 0); |
| |
| // Set RCVEnOut# strength to 2x (?) |
| maybe_strength_control = read8(RCOMP_MMIO + MAYBE_RCVENSTR) & 0xF8; |
| maybe_strength_control |= 4; |
| write8(RCOMP_MMIO + MAYBE_RCVENSTR, maybe_strength_control); |
| |
| write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x1c0); |
| write16(RCOMP_MMIO + 0x50, 0); |
| |
| // Set CS# strength for x4 SDRAM to 2x (?) |
| maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0xF8; |
| maybe_strength_control |= 4; |
| write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control); |
| |
| write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x140); |
| write16(RCOMP_MMIO + 0x48, 0); |
| |
| // Set CKE strength for x4 SDRAM to 2x (?) |
| maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0xF8; |
| maybe_strength_control |= 4; |
| write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control); |
| |
| write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xa0); |
| write16(RCOMP_MMIO + 0x44, 0); |
| |
| // Set CK strength for x4 SDRAM to 1x (?) |
| maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0xF8; |
| maybe_strength_control |= 1; |
| write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control); |
| |
| write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x180); |
| write16(RCOMP_MMIO + 0x4c, 0); |
| |
| write8(RCOMP_MMIO + 0x2c, 0xff); |
| |
| // Set the digital filter length to 8 (?) |
| dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); |
| |
| // NOTE: Some factory BIOS don't do this. |
| // Doesn't seem to matter either way. |
| dword &= ~2; |
| |
| dword |= 1; |
| write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); |
| |
| /* Wait 40 usec */ |
| SLOW_DOWN_IO; |
| |
| /* unblock updates */ |
| dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); |
| dword &= ~(1 << 9); |
| write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); |
| |
| // Force a RCOMP measurement cycle? |
| dword |= (1 << 8); |
| write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); |
| dword &= ~(1 << 8); |
| write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); |
| |
| /* Wait 40 usec */ |
| SLOW_DOWN_IO; |
| |
| /*disable access to the rcomp bar */ |
| dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); |
| dword &= ~(1 << 22); |
| pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); |
| |
| } |
| |
| /*----------------------------------------------------------------------------- |
| Public interface: |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Go through the JEDEC initialization sequence for all DIMMs, then enable |
| * refresh and initialize ECC and memory to zero. Upon exit, SDRAM is up |
| * and running. |
| * |
| * @param controllers Not used. |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| */ |
| static void sdram_enable(int controllers, |
| const struct mem_controller *ctrl) |
| { |
| uint8_t dimm_mask = pci_read_config16(PCI_DEV(0, 0, 0), SKPD); |
| uint32_t dram_controller_mode; |
| |
| if (dimm_mask == 0) |
| return; |
| |
| /* 1 & 2 Power up and start clocks */ |
| RAM_DEBUG_MESSAGE("Ram Enable 1\n"); |
| RAM_DEBUG_MESSAGE("Ram Enable 2\n"); |
| |
| /* A 200us delay is needed */ |
| DO_DELAY; EXTRA_DELAY; |
| |
| /* 3. Apply NOP */ |
| RAM_DEBUG_MESSAGE("Ram Enable 3\n"); |
| do_ram_command(RAM_COMMAND_NOP, 0); |
| EXTRA_DELAY; |
| |
| /* 4 Precharge all */ |
| RAM_DEBUG_MESSAGE("Ram Enable 4\n"); |
| do_ram_command(RAM_COMMAND_PRECHARGE, 0); |
| EXTRA_DELAY; |
| /* wait until the all banks idle state... */ |
| |
| /* 5. Issue EMRS to enable DLL */ |
| RAM_DEBUG_MESSAGE("Ram Enable 5\n"); |
| do_ram_command(RAM_COMMAND_EMRS, |
| SDRAM_EXTMODE_DLL_ENABLE | |
| SDRAM_EXTMODE_DRIVE_NORMAL); |
| EXTRA_DELAY; |
| |
| /* 6. Reset DLL */ |
| RAM_DEBUG_MESSAGE("Ram Enable 6\n"); |
| set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_DLL_RESET); |
| EXTRA_DELAY; |
| /* Ensure a 200us delay between the DLL reset in step 6 and the final |
| * mode register set in step 9. |
| * Infineon needs this before any other command is sent to the ram. |
| */ |
| DO_DELAY; EXTRA_DELAY; |
| |
| /* 7 Precharge all */ |
| RAM_DEBUG_MESSAGE("Ram Enable 7\n"); |
| do_ram_command(RAM_COMMAND_PRECHARGE, 0); |
| EXTRA_DELAY; |
| |
| /* 8 Now we need 2 AUTO REFRESH / CBR cycles to be performed */ |
| RAM_DEBUG_MESSAGE("Ram Enable 8\n"); |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| |
| /* And for good luck 6 more CBRs */ |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| EXTRA_DELAY; |
| |
| /* 9 mode register set */ |
| RAM_DEBUG_MESSAGE("Ram Enable 9\n"); |
| set_ram_mode(E7501_SDRAM_MODE | SDRAM_MODE_NORMAL); |
| EXTRA_DELAY; |
| |
| /* 10 DDR Receive FIFO RE-Sync */ |
| RAM_DEBUG_MESSAGE("Ram Enable 10\n"); |
| RAM_RESET_DDR_PTR(); |
| EXTRA_DELAY; |
| |
| /* 11 normal operation */ |
| RAM_DEBUG_MESSAGE("Ram Enable 11\n"); |
| do_ram_command(RAM_COMMAND_NORMAL, 0); |
| EXTRA_DELAY; |
| |
| // Reconfigure the row boundaries and Top of Low Memory |
| // to match the true size of the DIMMs |
| configure_e7501_ram_addresses(ctrl, dimm_mask); |
| |
| /* Finally enable refresh */ |
| dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); |
| dram_controller_mode |= (1 << 29); |
| pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); |
| EXTRA_DELAY; |
| initialize_ecc(); |
| |
| dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); /* FCS_EN */ |
| dram_controller_mode |= (1 << 17); // NOTE: undocumented reserved bit |
| pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); |
| |
| RAM_DEBUG_MESSAGE("Northbridge following SDRAM init:\n"); |
| DUMPNORTH(); |
| } |
| |
| /** |
| * Configure SDRAM controller parameters that depend on characteristics of the |
| * DIMMs installed in the system. These characteristics are read from the |
| * DIMMs via the standard Serial Presence Detect (SPD) interface. |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| */ |
| static void sdram_set_spd_registers(const struct mem_controller *ctrl) |
| { |
| uint8_t dimm_mask; |
| |
| RAM_DEBUG_MESSAGE("Reading SPD data...\n"); |
| |
| dimm_mask = spd_get_supported_dimms(ctrl); |
| |
| if (dimm_mask == 0) { |
| print_debug("No usable memory for this controller\n"); |
| } else { |
| enable_e7501_clocks(dimm_mask); |
| |
| RAM_DEBUG_MESSAGE("setting based on SPD data...\n"); |
| |
| configure_e7501_row_attributes(ctrl, dimm_mask); |
| configure_e7501_dram_controller_mode(ctrl, dimm_mask); |
| configure_e7501_cas_latency(ctrl, dimm_mask); |
| RAM_RESET_DDR_PTR(); |
| |
| configure_e7501_dram_timing(ctrl, dimm_mask); |
| DO_DELAY; |
| RAM_DEBUG_MESSAGE("done\n"); |
| } |
| |
| /* NOTE: configure_e7501_ram_addresses() is NOT called here. |
| * We want to keep the default 64 MB/row mapping until sdram_enable() is called, |
| * even though the default mapping is almost certainly incorrect. |
| * The default mapping makes it easy to initialize all of the DIMMs |
| * even if the total system memory is > 4 GB. |
| * |
| * Save the dimm_mask for when sdram_enable is called, so it can call |
| * configure_e7501_ram_addresses() without having to regenerate the bitmask |
| * of usable DIMMs. |
| */ |
| pci_write_config16(PCI_DEV(0, 0, 0), SKPD, dimm_mask); |
| } |
| |
| /** |
| * Do basic RAM setup that does NOT depend on serial presence detect |
| * information (i.e. independent of DIMM specifics). |
| * |
| * @param ctrl PCI addresses of memory controller functions, and SMBus |
| * addresses of DIMM slots on the mainboard. |
| */ |
| static void sdram_set_registers(const struct mem_controller *ctrl) |
| { |
| RAM_DEBUG_MESSAGE("Northbridge prior to SDRAM init:\n"); |
| DUMPNORTH(); |
| |
| ram_set_rcomp_regs(); |
| ram_set_d0f0_regs(); |
| } |