| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2011 Sven Schnelle <svens@stackframe.org> |
| * Copyright (C) 2013 Vladimir Serbinenko <phcoder@gmail.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #define __SIMPLE_DEVICE__ |
| #include <console/console.h> |
| #include <arch/io.h> |
| #include <device/pnp_ops.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pnp.h> |
| #include <delay.h> |
| #include "dock.h" |
| #include <superio/nsc/pc87382/pc87382.h> |
| |
| #include <southbridge/intel/i82801ix/i82801ix.h> |
| #include <ec/lenovo/h8/h8.h> |
| #include <ec/acpi/ec.h> |
| |
| struct pin_config { |
| u8 port; |
| u8 mode; |
| }; |
| |
| static int poll_clk_stable(pnp_devfn_t dev, int timeout) |
| { |
| /* Enable 14.318MHz CLK on CLKIN */ |
| pnp_write_config(dev, 0x29, 0xa0); |
| while(!(pnp_read_config(dev, 0x29) & 0x10) && timeout--) |
| udelay(1000); |
| if (!timeout) |
| return 1; |
| |
| return 0; |
| } |
| |
| static int gpio_init(pnp_devfn_t gpio, u16 gpio_base, |
| const struct pin_config pincfg[], int num_cfgs) |
| { |
| int i; |
| |
| /* Enable GPIO LDN. */ |
| pnp_set_logical_device(gpio); |
| pnp_set_iobase(gpio, PNP_IDX_IO0, gpio_base); |
| pnp_set_enable(gpio, 1); |
| |
| for (i = 0; i < num_cfgs; i++) { |
| pnp_write_config(gpio, 0xf0, pincfg[i].port); |
| pnp_write_config(gpio, 0xf1, pincfg[i].mode); |
| pnp_write_config(gpio, 0xf2, 0x0); |
| } |
| return 0; |
| } |
| |
| static const pnp_devfn_t l_dlpc = PNP_DEV(0x164e, PC87382_DOCK); |
| static const pnp_devfn_t l_gpio = PNP_DEV(0x164e, PC87382_GPIO); |
| |
| static int pc87382_init(pnp_devfn_t dlpc, u16 dlpc_base) |
| { |
| /* Maximum 3300 LCLKs at 14.318MHz */ |
| int timeout = 230; |
| |
| /* Enable LPC bridge LDN. */ |
| pnp_set_logical_device(dlpc); |
| pnp_set_iobase(dlpc, PNP_IDX_IO0, dlpc_base); |
| pnp_set_enable(dlpc, 1); |
| |
| /* Reset docking state */ |
| outb(0x00, dlpc_base); |
| outb(0x07, dlpc_base); |
| while (!(inb(dlpc_base) & 8) && timeout--) |
| udelay(1); |
| if (!timeout) |
| return 1; |
| |
| return 0; |
| } |
| |
| static void pc87382_close(pnp_devfn_t dlpc) |
| { |
| pnp_set_logical_device(dlpc); |
| |
| /* Disconnect LPC bus */ |
| u16 dlpc_base = pnp_read_iobase(dlpc, PNP_IDX_IO0); |
| if (dlpc_base) { |
| outb(0x00, dlpc_base); |
| pnp_set_enable(dlpc, 0); |
| } |
| } |
| |
| static const struct pin_config local_gpio[] = { |
| {0x00, 3}, {0x01, 3}, {0x02, 0}, {0x03, 3}, |
| {0x04, 4}, {0x20, 4}, {0x21, 4}, {0x23, 4}, |
| }; |
| |
| /* Enable internal clock and configure GPIO LDN */ |
| int pc87382_early(void) |
| { |
| /* Wake-up time is 33 msec (maximum). */ |
| if (poll_clk_stable(l_gpio, 33) != 0) |
| return 1; |
| |
| /* Set up GPIOs */ |
| if (gpio_init(l_gpio, DLPC_GPIO_BASE, |
| local_gpio, ARRAY_SIZE(local_gpio)) != 0) { |
| return 1; |
| } |
| |
| return 0; |
| } |
| |
| static int pc87382_connect(void) |
| { |
| u8 reg; |
| |
| reg = inb(DLPC_GPDO0); |
| reg |= D_PLTRST | D_LPCPD; |
| /* Deassert D_PLTRST# and D_LPCPD# */ |
| outb(reg, DLPC_GPDO0); |
| |
| if (pc87382_init(l_dlpc, DLPC_CONTROL) != 0) |
| return 1; |
| |
| /* Assert D_PLTRST# */ |
| reg &= ~D_PLTRST; |
| outb(reg, DLPC_GPDO0); |
| udelay(1000); |
| |
| /* Deassert D_PLTRST# */ |
| reg |= D_PLTRST; |
| outb(reg, DLPC_GPDO0); |
| mdelay(10); |
| |
| return 0; |
| } |
| |
| static void pc87382_disconnect(void) |
| { |
| pc87382_close(l_dlpc); |
| |
| /* Assert D_PLTRST# and D_LPCPD# */ |
| u8 reg = inb(DLPC_GPDO0); |
| reg &= ~(D_PLTRST | D_LPCPD); |
| outb(reg, DLPC_GPDO0); |
| } |
| |
| /* Returns 3bit dock id */ |
| static u8 dock_identify(void) |
| { |
| u8 id; |
| |
| /* Make sure GPIO LDN is configured first ! */ |
| id = (inb(DLPC_GPDI0) >> 4) & 1; |
| id |= (inb(DLPC_GPDI2) & 3) << 1; |
| |
| return id; |
| } |
| |
| /* Docking station side. */ |
| |
| #include <superio/nsc/pc87384/pc87384.h> |
| |
| static const pnp_devfn_t r_gpio = PNP_DEV(SUPERIO_DEV, PC87384_GPIO); |
| static const pnp_devfn_t r_serial = PNP_DEV(SUPERIO_DEV, PC87384_SP1); |
| |
| static const struct pin_config remote_gpio[] = { |
| {0x00, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| {0x01, PC87384_GPIO_PIN_TYPE_PUSH_PULL | PC87384_GPIO_PIN_OE}, |
| {0x02, PC87384_GPIO_PIN_TYPE_PUSH_PULL | PC87384_GPIO_PIN_OE}, |
| {0x03, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| {0x04, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| {0x05, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| {0x06, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| {0x07, PC87384_GPIO_PIN_DEBOUNCE | PC87384_GPIO_PIN_PULLUP}, |
| }; |
| |
| static int pc87384_init(void) |
| { |
| if (poll_clk_stable(r_gpio, 1000) != 0) |
| return 1; |
| |
| /* set GPIO pins to Serial/Parallel Port |
| * functions |
| */ |
| pnp_write_config(r_gpio, 0x22, 0xa9); |
| |
| /* enable serial port */ |
| |
| if (CONFIG_TTYS0_BASE > 0) { |
| pnp_set_logical_device(r_serial); |
| pnp_set_iobase(r_serial, PNP_IDX_IO0, CONFIG_TTYS0_BASE); |
| pnp_set_enable(r_serial, 1); |
| } |
| |
| if (gpio_init(r_gpio, DOCK_GPIO_BASE, |
| remote_gpio, ARRAY_SIZE(remote_gpio)) != 0) |
| return 1; |
| |
| /* no GPIO events enabled for PORT0 */ |
| outb(0x00, DOCK_GPIO_BASE + 0x02); |
| /* clear GPIO events on PORT0 */ |
| outb(0xff, DOCK_GPIO_BASE + 0x03); |
| outb(0xff, DOCK_GPIO_BASE + 0x04); |
| |
| /* no GPIO events enabled for PORT1 */ |
| outb(0x00, DOCK_GPIO_BASE + 0x06); |
| /* clear GPIO events on PORT1*/ |
| outb(0xff, DOCK_GPIO_BASE + 0x07); |
| outb(0x1f, DOCK_GPIO_BASE + 0x08); |
| |
| outb(0xfd, DOCK_GPIO_BASE + 0x00); |
| |
| return 0; |
| } |
| |
| /* Mainboard */ |
| |
| void dock_connect(void) |
| { |
| const u8 id = dock_identify(); |
| |
| /* Dock type 2505 doesn't have serial, LPT port or LEDs */ |
| if (id == DOCK_TYPE_NONE || id == DOCK_TYPE_2505) |
| return; |
| |
| if (pc87382_connect() != 0 || pc87384_init() != 0) { |
| pc87382_disconnect(); |
| return; |
| } |
| |
| ec_write(H8_LED_CONTROL, |
| H8_LED_CONTROL_OFF | H8_LED_CONTROL_DOCK_LED1); |
| ec_write(H8_LED_CONTROL, |
| H8_LED_CONTROL_ON | H8_LED_CONTROL_DOCK_LED2); |
| } |
| |
| void dock_disconnect(void) |
| { |
| pc87382_disconnect(); |
| |
| ec_write(H8_LED_CONTROL, |
| H8_LED_CONTROL_OFF | H8_LED_CONTROL_DOCK_LED1); |
| ec_write(H8_LED_CONTROL, |
| H8_LED_CONTROL_OFF | H8_LED_CONTROL_DOCK_LED2); |
| } |
| |
| void dock_info(void) |
| { |
| const u8 id = dock_identify(); |
| |
| if (id != DOCK_TYPE_NONE) |
| printk(BIOS_DEBUG, "DOCK: is present: id=%d\n", id); |
| else |
| printk(BIOS_DEBUG, "DOCK: not connected\n"); |
| } |