| /** @file |
| |
| Copyright (c) 2023, Intel Corporation. All rights reserved.<BR> |
| |
| Redistribution and use in source and binary forms, with or without modification, |
| are permitted provided that the following conditions are met: |
| |
| * Redistributions of source code must retain the above copyright notice, this |
| list of conditions and the following disclaimer. |
| * Redistributions in binary form must reproduce the above copyright notice, this |
| list of conditions and the following disclaimer in the documentation and/or |
| other materials provided with the distribution. |
| * Neither the name of Intel Corporation nor the names of its contributors may |
| be used to endorse or promote products derived from this software without |
| specific prior written permission. |
| |
| THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
| AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
| ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE |
| LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
| CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
| SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS |
| INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN |
| CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) |
| ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF |
| THE POSSIBILITY OF SUCH DAMAGE. |
| |
| This file is automatically generated. Please do NOT modify !!! |
| |
| **/ |
| |
| #ifndef __FSPSUPD_H__ |
| #define __FSPSUPD_H__ |
| |
| #include <FspUpd.h> |
| |
| #pragma pack(1) |
| |
| |
| /// |
| /// Azalia Header structure |
| /// |
| typedef struct { |
| UINT16 VendorId; ///< Codec Vendor ID |
| UINT16 DeviceId; ///< Codec Device ID |
| UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision. |
| UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI. |
| UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer. |
| UINT32 Reserved; ///< Reserved for future use. Must be set to 0. |
| } AZALIA_HEADER; |
| |
| /// |
| /// Audio Azalia Verb Table structure |
| /// |
| typedef struct { |
| AZALIA_HEADER Header; ///< AZALIA PCH header |
| UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header |
| } AUDIO_AZALIA_VERB_TABLE; |
| |
| /// |
| /// Refer to the definition of PCH_INT_PIN |
| /// |
| typedef enum { |
| SiPchNoInt, ///< No Interrupt Pin |
| SiPchIntA, |
| SiPchIntB, |
| SiPchIntC, |
| SiPchIntD |
| } SI_PCH_INT_PIN; |
| /// |
| /// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device. |
| /// |
| typedef struct { |
| UINT8 Device; ///< Device number |
| UINT8 Function; ///< Device function |
| UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN) |
| UINT8 Irq; ///< IRQ to be set for device. |
| } SI_PCH_DEVICE_INTERRUPT_CONFIG; |
| |
| #define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices |
| |
| |
| /** Fsp S Configuration |
| **/ |
| typedef struct { |
| |
| /** Offset 0x0040 - Logo Pointer |
| Points to PEI Display Logo Image |
| **/ |
| UINT32 LogoPtr; |
| |
| /** Offset 0x0044 - Logo Size |
| Size of PEI Display Logo Image |
| **/ |
| UINT32 LogoSize; |
| |
| /** Offset 0x0048 - Blt Buffer Address |
| Address of Blt buffer |
| **/ |
| UINT32 BltBufferAddress; |
| |
| /** Offset 0x004C - Blt Buffer Size |
| Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of |
| EFI_GRAPHICS_OUTPUT_BLT_PIXEL) |
| **/ |
| UINT32 BltBufferSize; |
| |
| /** Offset 0x0050 - Graphics Configuration Ptr |
| Points to VBT |
| **/ |
| UINT32 GraphicsConfigPtr; |
| |
| /** Offset 0x0054 - Enable Device 4 |
| Enable/disable Device 4 |
| $EN_DIS |
| **/ |
| UINT8 Device4Enable; |
| |
| /** Offset 0x0055 - Show SPI controller |
| Enable/disable to show SPI controller. |
| $EN_DIS |
| **/ |
| UINT8 ShowSpiController; |
| |
| /** Offset 0x0056 - Reserved |
| **/ |
| UINT8 Reserved0[2]; |
| |
| /** Offset 0x0058 - MicrocodeRegionBase |
| Memory Base of Microcode Updates |
| **/ |
| UINT32 MicrocodeRegionBase; |
| |
| /** Offset 0x005C - MicrocodeRegionSize |
| Size of Microcode Updates |
| **/ |
| UINT32 MicrocodeRegionSize; |
| |
| /** Offset 0x0060 - Turbo Mode |
| Enable/Disable processor Turbo Mode. 0:disable, <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 TurboMode; |
| |
| /** Offset 0x0061 - Enable SATA SALP Support |
| Enable/disable SATA Aggressive Link Power Management. |
| $EN_DIS |
| **/ |
| UINT8 SataSalpSupport; |
| |
| /** Offset 0x0062 - Enable SATA ports |
| Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1, |
| and so on. |
| **/ |
| UINT8 SataPortsEnable[8]; |
| |
| /** Offset 0x006A - Enable SATA DEVSLP Feature |
| Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each |
| port, byte0 for port0, byte1 for port1, and so on. |
| **/ |
| UINT8 SataPortsDevSlp[8]; |
| |
| /** Offset 0x0072 - Reserved |
| **/ |
| UINT8 Reserved1[34]; |
| |
| /** Offset 0x0094 - Enable USB2 ports |
| Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for |
| port1, and so on. |
| **/ |
| UINT8 PortUsb20Enable[16]; |
| |
| /** Offset 0x00A4 - Enable USB3 ports |
| Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for |
| port1, and so on. |
| **/ |
| UINT8 PortUsb30Enable[10]; |
| |
| /** Offset 0x00AE - Enable xDCI controller |
| Enable/disable to xDCI controller. |
| $EN_DIS |
| **/ |
| UINT8 XdciEnable; |
| |
| /** Offset 0x00AF - Reserved |
| **/ |
| UINT8 Reserved2; |
| |
| /** Offset 0x00B0 - Address of PCH_DEVICE_INTERRUPT_CONFIG table. |
| The address of the table of PCH_DEVICE_INTERRUPT_CONFIG. |
| **/ |
| UINT32 DevIntConfigPtr; |
| |
| /** Offset 0x00B4 - Number of DevIntConfig Entry |
| Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr |
| must not be NULL. |
| **/ |
| UINT8 NumOfDevIntConfig; |
| |
| /** Offset 0x00B5 - PIRQx to IRQx Map Config |
| PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for |
| PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy |
| 8259 PCI mode. |
| **/ |
| UINT8 PxRcConfig[8]; |
| |
| /** Offset 0x00BD - Select GPIO IRQ Route |
| GPIO IRQ Select. The valid value is 14 or 15. |
| **/ |
| UINT8 GpioIrqRoute; |
| |
| /** Offset 0x00BE - Select SciIrqSelect |
| SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only. |
| **/ |
| UINT8 SciIrqSelect; |
| |
| /** Offset 0x00BF - Select TcoIrqSelect |
| TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23. |
| **/ |
| UINT8 TcoIrqSelect; |
| |
| /** Offset 0x00C0 - Enable/Disable Tco IRQ |
| Enable/disable TCO IRQ |
| $EN_DIS |
| **/ |
| UINT8 TcoIrqEnable; |
| |
| /** Offset 0x00C1 - PCH HDA Verb Table Entry Number |
| Number of Entries in Verb Table. |
| **/ |
| UINT8 PchHdaVerbTableEntryNum; |
| |
| /** Offset 0x00C2 - Reserved |
| **/ |
| UINT8 Reserved3[2]; |
| |
| /** Offset 0x00C4 - PCH HDA Verb Table Pointer |
| Pointer to Array of pointers to Verb Table. |
| **/ |
| UINT32 PchHdaVerbTablePtr; |
| |
| /** Offset 0x00C8 - PCH HDA Codec Sx Wake Capability |
| Capability to detect wake initiated by a codec in Sx |
| **/ |
| UINT8 PchHdaCodecSxWakeCapability; |
| |
| /** Offset 0x00C9 - Enable SATA |
| Enable/disable SATA controller. |
| $EN_DIS |
| **/ |
| UINT8 SataEnable; |
| |
| /** Offset 0x00CA - SATA Mode |
| Select SATA controller working mode. |
| 0:AHCI, 1:RAID |
| **/ |
| UINT8 SataMode; |
| |
| /** Offset 0x00CB - SPIn Device Mode |
| Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available |
| modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden |
| **/ |
| UINT8 SerialIoSpiMode[7]; |
| |
| /** Offset 0x00D2 - SPI<N> Chip Select Polarity |
| Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow, |
| 1:SerialIoSpiCsActiveHigh |
| **/ |
| UINT8 SerialIoSpiCsPolarity[14]; |
| |
| /** Offset 0x00E0 - SPI<N> Chip Select Enable |
| 0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled |
| **/ |
| UINT8 SerialIoSpiCsEnable[14]; |
| |
| /** Offset 0x00EE - SPIn Default Chip Select Output |
| Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available |
| options: 0:CS0, 1:CS1 |
| **/ |
| UINT8 SerialIoSpiDefaultCsOutput[7]; |
| |
| /** Offset 0x00F5 - SPIn Default Chip Select Mode HW/SW |
| Sets Default CS Mode Hardware or Software. N represents controller index: SPI0, |
| SPI1, ... Available options: 0:HW, 1:SW |
| **/ |
| UINT8 SerialIoSpiCsMode[7]; |
| |
| /** Offset 0x00FC - SPIn Default Chip Select State Low/High |
| Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ... |
| Available options: 0:Low, 1:High |
| **/ |
| UINT8 SerialIoSpiCsState[7]; |
| |
| /** Offset 0x0103 - Reserved |
| **/ |
| UINT8 Reserved4[141]; |
| |
| /** Offset 0x0190 - UARTn Device Mode |
| Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available |
| modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom, |
| 4:SerialIoUartSkipInit |
| **/ |
| UINT8 SerialIoUartMode[7]; |
| |
| /** Offset 0x0197 - Reserved |
| **/ |
| UINT8 Reserved5; |
| |
| /** Offset 0x0198 - Default BaudRate for each Serial IO UART |
| Set default BaudRate Supported from 0 - default to 6000000 |
| **/ |
| UINT32 SerialIoUartBaudRate[7]; |
| |
| /** Offset 0x01B4 - Default ParityType for each Serial IO UART |
| Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity |
| **/ |
| UINT8 SerialIoUartParity[7]; |
| |
| /** Offset 0x01BB - Default DataBits for each Serial IO UART |
| Set default word length. 0: Default, 5,6,7,8 |
| **/ |
| UINT8 SerialIoUartDataBits[7]; |
| |
| /** Offset 0x01C2 - Default StopBits for each Serial IO UART |
| Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: |
| TwoStopBits |
| **/ |
| UINT8 SerialIoUartStopBits[7]; |
| |
| /** Offset 0x01C9 - Power Gating mode for each Serial IO UART that works in COM mode |
| Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto |
| **/ |
| UINT8 SerialIoUartPowerGating[7]; |
| |
| /** Offset 0x01D0 - Enable Dma for each Serial IO UART that supports it |
| Set DMA/PIO mode. 0: Disabled, 1: Enabled |
| **/ |
| UINT8 SerialIoUartDmaEnable[7]; |
| |
| /** Offset 0x01D7 - Enables UART hardware flow control, CTS and RTS lines |
| Enables UART hardware flow control, CTS and RTS lines. |
| **/ |
| UINT8 SerialIoUartAutoFlow[7]; |
| |
| /** Offset 0x01DE - Reserved |
| **/ |
| UINT8 Reserved6[2]; |
| |
| /** Offset 0x01E0 - SerialIoUartRtsPinMuxPolicy |
| Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS* |
| for possible values. |
| **/ |
| UINT32 SerialIoUartRtsPinMuxPolicy[7]; |
| |
| /** Offset 0x01FC - SerialIoUartCtsPinMuxPolicy |
| Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS* |
| for possible values. |
| **/ |
| UINT32 SerialIoUartCtsPinMuxPolicy[7]; |
| |
| /** Offset 0x0218 - SerialIoUartRxPinMuxPolicy |
| Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for |
| possible values. |
| **/ |
| UINT32 SerialIoUartRxPinMuxPolicy[7]; |
| |
| /** Offset 0x0234 - SerialIoUartTxPinMuxPolicy |
| Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for |
| possible values. |
| **/ |
| UINT32 SerialIoUartTxPinMuxPolicy[7]; |
| |
| /** Offset 0x0250 - Serial IO UART DBG2 table |
| Enable or disable Serial Io UART DBG2 table, default is Disable; <b>0: Disable;</b> |
| 1: Enable. |
| **/ |
| UINT8 SerialIoUartDbg2[7]; |
| |
| /** Offset 0x0257 - I2Cn Device Mode |
| Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available |
| modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden |
| **/ |
| UINT8 SerialIoI2cMode[8]; |
| |
| /** Offset 0x025F - Reserved |
| **/ |
| UINT8 Reserved7; |
| |
| /** Offset 0x0260 - Serial IO I2C SDA Pin Muxing |
| Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for |
| possible values. |
| **/ |
| UINT32 PchSerialIoI2cSdaPinMux[8]; |
| |
| /** Offset 0x0280 - Serial IO I2C SCL Pin Muxing |
| Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for |
| possible values. |
| **/ |
| UINT32 PchSerialIoI2cSclPinMux[8]; |
| |
| /** Offset 0x02A0 - PCH SerialIo I2C Pads Termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination |
| respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on. |
| **/ |
| UINT8 PchSerialIoI2cPadsTermination[8]; |
| |
| /** Offset 0x02A8 - I3C Device Mode |
| Selects I3c operation mode. Available modes: 0:SerialIoI3cDisabled, 1:SerialIoI3cPci, |
| 2:SerialIoI3cPhantom (only applicable to I3C1, controlls GPIO enabling) |
| **/ |
| UINT8 SerialIoI3cMode[2]; |
| |
| /** Offset 0x02AA - Reserved |
| **/ |
| UINT8 Reserved8[38]; |
| |
| /** Offset 0x02D0 - ISH GP GPIO Pin Muxing |
| Determines ISH GP GPIO Pin muxing. See GPIO_*_MUXING_ISH_GP_x_GPIO_*. 'x' are GP_NUMBER |
| **/ |
| UINT32 IshGpGpioPinMuxing[12]; |
| |
| /** Offset 0x0300 - ISH UART Rx Pin Muxing |
| Determines ISH UART Rx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_TXD_* |
| **/ |
| UINT32 IshUartRxPinMuxing[3]; |
| |
| /** Offset 0x030C - ISH UART Tx Pin Muxing |
| Determines ISH UART Tx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_RXD_* |
| **/ |
| UINT32 IshUartTxPinMuxing[3]; |
| |
| /** Offset 0x0318 - ISH UART Rts Pin Muxing |
| Select ISH UART Rts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_RTS_* for possible values. |
| **/ |
| UINT32 IshUartRtsPinMuxing[3]; |
| |
| /** Offset 0x0324 - ISH UART Rts Pin Muxing |
| Select ISH UART Cts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_CTS_* for possible values. |
| **/ |
| UINT32 IshUartCtsPinMuxing[3]; |
| |
| /** Offset 0x0330 - ISH I2C SDA Pin Muxing |
| Select ISH I2C SDA Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SDA_* for possible values. |
| **/ |
| UINT32 IshI2cSdaPinMuxing[3]; |
| |
| /** Offset 0x033C - ISH I2C SCL Pin Muxing |
| Select ISH I2C SCL Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SCL_* for possible values. |
| **/ |
| UINT32 IshI2cSclPinMuxing[3]; |
| |
| /** Offset 0x0348 - Reserved |
| **/ |
| UINT8 Reserved9[8]; |
| |
| /** Offset 0x0350 - ISH SPI MOSI Pin Muxing |
| Select ISH SPI MOSI Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MOSI_* for possible values. |
| **/ |
| UINT32 IshSpiMosiPinMuxing[2]; |
| |
| /** Offset 0x0358 - ISH SPI MISO Pin Muxing |
| Select ISH SPI MISO Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MISO_* for possible values. |
| **/ |
| UINT32 IshSpiMisoPinMuxing[2]; |
| |
| /** Offset 0x0360 - ISH SPI CLK Pin Muxing |
| Select ISH SPI CLK Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CLK_* for possible values. |
| **/ |
| UINT32 IshSpiClkPinMuxing[2]; |
| |
| /** Offset 0x0368 - ISH SPI CS#N Pin Muxing |
| Select ISH SPI CS#N Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CS<N>_* for possible |
| values. N-SPI number, 0-1. |
| **/ |
| UINT32 IshSpiCsPinMuxing[4]; |
| |
| /** Offset 0x0378 - ISH GP GPIO Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo GP#N GPIO pads termination |
| respectively. #N are GP_NUMBER, not strictly relate to indexes of this table. Index |
| 0-23 -> ISH_GP_0-23, Index 24-25 -> ISH_GP_30-31 |
| **/ |
| UINT8 IshGpGpioPadTermination[12]; |
| |
| /** Offset 0x0384 - ISH UART Rx Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rx pads termination |
| respectively. #N-byte for each controller, byte0 for UART0 Rx, byte1 for UART1 |
| Rx, and so on. |
| **/ |
| UINT8 IshUartRxPadTermination[3]; |
| |
| /** Offset 0x0387 - ISH UART Tx Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Tx pads termination |
| respectively. #N-byte for each controller, byte0 for UART0 Tx, byte1 for UART1 |
| Tx, and so on. |
| **/ |
| UINT8 IshUartTxPadTermination[3]; |
| |
| /** Offset 0x038A - ISH UART Rts Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rts pads termination |
| respectively. #N-byte for each controller, byte0 for UART0 Rts, byte1 for UART1 |
| Rts, and so on. |
| **/ |
| UINT8 IshUartRtsPadTermination[3]; |
| |
| /** Offset 0x038D - ISH UART Rts Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Cts pads termination |
| respectively. #N-byte for each controller, byte0 for UART0 Cts, byte1 for UART1 |
| Cts, and so on. |
| **/ |
| UINT8 IshUartCtsPadTermination[3]; |
| |
| /** Offset 0x0390 - ISH I2C SDA Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Sda pads termination |
| respectively. #N-byte for each controller, byte0 for I2C0 Sda, byte1 for I2C1 Sda, |
| and so on. |
| **/ |
| UINT8 IshI2cSdaPadTermination[3]; |
| |
| /** Offset 0x0393 - Reserved |
| **/ |
| UINT8 Reserved10; |
| |
| /** Offset 0x0394 - ISH I2C SCL Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Scl pads termination |
| respectively. #N-byte for each controller, byte0 for I2C0 Scl, byte1 for I2C1 Scl, |
| and so on. |
| **/ |
| UINT8 IshI2cSclPadTermination[3]; |
| |
| /** Offset 0x0397 - Reserved |
| **/ |
| UINT8 Reserved11; |
| |
| /** Offset 0x0398 - ISH SPI MOSI Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Mosi pads termination |
| respectively. #N-byte for each controller, byte0 for SPI0 Mosi, byte1 for SPI1 |
| Mosi, and so on. |
| **/ |
| UINT8 IshSpiMosiPadTermination[2]; |
| |
| /** Offset 0x039A - ISH SPI MISO Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Miso pads termination |
| respectively. #N-byte for each controller, byte0 for SPI0 Miso, byte1 for SPI1 |
| Miso, and so on. |
| **/ |
| UINT8 IshSpiMisoPadTermination[2]; |
| |
| /** Offset 0x039C - ISH SPI CLK Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Clk pads termination |
| respectively. #N-byte for each controller, byte0 for SPI0 Clk, byte1 for SPI1 Clk, |
| and so on. |
| **/ |
| UINT8 IshSpiClkPadTermination[2]; |
| |
| /** Offset 0x039E - ISH SPI CS#N Pad termination |
| 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, |
| 0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Cs#M pads termination |
| respectively. N*M-byte for each controller, byte0 for SPI0 Cs0, byte1 for SPI1 |
| Cs1, SPI1 Cs0, byte2, SPI1 Cs1, byte3 |
| **/ |
| UINT8 IshSpiCsPadTermination[4]; |
| |
| /** Offset 0x03A2 - Enable PCH ISH SPI Cs#N pins assigned |
| Set if ISH SPI Cs#N pins are to be enabled by BIOS. 0: Disable; 1: Enable. N-Cs |
| number: 0-1 |
| **/ |
| UINT8 PchIshSpiCsEnable[4]; |
| |
| /** Offset 0x03A6 - USB Per Port HS Preemphasis Bias |
| USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, |
| 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port. |
| **/ |
| UINT8 Usb2PhyPetxiset[16]; |
| |
| /** Offset 0x03B6 - USB Per Port HS Transmitter Bias |
| USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, |
| 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port. |
| **/ |
| UINT8 Usb2PhyTxiset[16]; |
| |
| /** Offset 0x03C6 - USB Per Port HS Transmitter Emphasis |
| USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON, |
| 10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port. |
| **/ |
| UINT8 Usb2PhyPredeemp[16]; |
| |
| /** Offset 0x03D6 - USB Per Port Half Bit Pre-emphasis |
| USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis. |
| One byte for each port. |
| **/ |
| UINT8 Usb2PhyPehalfbit[16]; |
| |
| /** Offset 0x03E6 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment |
| Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value |
| in arrary can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxDeEmphEnable[10]; |
| |
| /** Offset 0x03F0 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting |
| USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16], |
| <b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxDeEmph[10]; |
| |
| /** Offset 0x03FA - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment |
| Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value |
| in arrary can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxDownscaleAmpEnable[10]; |
| |
| /** Offset 0x0404 - USB 3.0 TX Output Downscale Amplitude Adjustment |
| USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default |
| = 00h</b>. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxDownscaleAmp[10]; |
| |
| /** Offset 0x040E |
| **/ |
| UINT8 PchUsb3HsioCtrlAdaptOffsetCfgEnable[10]; |
| |
| /** Offset 0x0418 |
| **/ |
| UINT8 PchUsb3HsioFilterSelNEnable[10]; |
| |
| /** Offset 0x0422 |
| **/ |
| UINT8 PchUsb3HsioFilterSelPEnable[10]; |
| |
| /** Offset 0x042C |
| **/ |
| UINT8 PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10]; |
| |
| /** Offset 0x0436 |
| **/ |
| UINT8 PchUsb3HsioCtrlAdaptOffsetCfg[10]; |
| |
| /** Offset 0x0440 |
| **/ |
| UINT8 PchUsb3HsioOlfpsCfgPullUpDwnRes[10]; |
| |
| /** Offset 0x044A |
| **/ |
| UINT8 PchUsb3HsioFilterSelN[10]; |
| |
| /** Offset 0x0454 |
| **/ |
| UINT8 PchUsb3HsioFilterSelP[10]; |
| |
| /** Offset 0x045E - Enable LAN |
| Enable/disable LAN controller. |
| $EN_DIS |
| **/ |
| UINT8 PchLanEnable; |
| |
| /** Offset 0x045F - Enable PCH TSN |
| Enable/disable TSN on the PCH. |
| $EN_DIS |
| **/ |
| UINT8 PchTsnEnable; |
| |
| /** Offset 0x0460 - TSN Link Speed |
| Set TSN Link Speed. |
| 0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps |
| **/ |
| UINT8 PchTsnLinkSpeed; |
| |
| /** Offset 0x0461 - Reserved |
| **/ |
| UINT8 Reserved12[19]; |
| |
| /** Offset 0x0474 - PCIe PTM enable/disable |
| Enable/disable Precision Time Measurement for PCIE Root Ports. |
| **/ |
| UINT8 PciePtm[29]; |
| |
| /** Offset 0x0491 - Reserved |
| **/ |
| UINT8 Reserved13[29]; |
| |
| /** Offset 0x04AE - USB PDO Programming |
| Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming |
| during later phase. 1: enable, 0: disable |
| $EN_DIS |
| **/ |
| UINT8 UsbPdoProgramming; |
| |
| /** Offset 0x04AF - Reserved |
| **/ |
| UINT8 Reserved14[5]; |
| |
| /** Offset 0x04B4 - Power button debounce configuration |
| Debounce time for PWRBTN in microseconds. For values not supported by HW, they will |
| be rounded down to closest supported on. 0: disable, 250-1024000us: supported range |
| **/ |
| UINT32 PmcPowerButtonDebounce; |
| |
| /** Offset 0x04B8 - Reserved |
| **/ |
| UINT8 Reserved15; |
| |
| /** Offset 0x04B9 - PCH eSPI Link Configuration Lock (SBLCL) |
| Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI target |
| addresseses from range 0x0 - 0x7FF |
| $EN_DIS |
| **/ |
| UINT8 PchEspiLockLinkConfiguration; |
| |
| /** Offset 0x04BA - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states |
| Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 |
| **/ |
| UINT8 PchFivrExtV1p05RailEnabledStates; |
| |
| /** Offset 0x04BB - Mask to enable the platform configuration of external V1p05 VR rail |
| External V1P05 Rail Supported Configuration |
| **/ |
| UINT8 PchFivrExtV1p05RailSupportedVoltageStates; |
| |
| /** Offset 0x04BC - External V1P05 Voltage Value that will be used in S0i2/S0i3 states |
| Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...) |
| **/ |
| UINT16 PchFivrExtV1p05RailVoltage; |
| |
| /** Offset 0x04BE - External V1P05 Icc Max Value |
| Granularity of this setting is 1mA and maximal possible value is 200mA |
| **/ |
| UINT8 PchFivrExtV1p05RailIccMax; |
| |
| /** Offset 0x04BF - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states |
| Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 |
| **/ |
| UINT8 PchFivrExtVnnRailEnabledStates; |
| |
| /** Offset 0x04C0 - Mask to enable the platform configuration of external Vnn VR rail |
| External Vnn Rail Supported Configuration |
| **/ |
| UINT8 PchFivrExtVnnRailSupportedVoltageStates; |
| |
| /** Offset 0x04C1 - Reserved |
| **/ |
| UINT8 Reserved16; |
| |
| /** Offset 0x04C2 - External Vnn Voltage Value that will be used in S0ix/Sx states |
| Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420 |
| **/ |
| UINT16 PchFivrExtVnnRailVoltage; |
| |
| /** Offset 0x04C4 - External Vnn Icc Max Value that will be used in S0ix/Sx states |
| Granularity of this setting is 1mA and maximal possible value is 200mA |
| **/ |
| UINT8 PchFivrExtVnnRailIccMax; |
| |
| /** Offset 0x04C5 - Mask to enable the usage of external Vnn VR rail in Sx states |
| Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in |
| Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5 |
| **/ |
| UINT8 PchFivrExtVnnRailSxEnabledStates; |
| |
| /** Offset 0x04C6 - External Vnn Voltage Value that will be used in Sx states |
| Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments |
| (0=0mV, 1=2.5mV, 2=5mV...) |
| **/ |
| UINT16 PchFivrExtVnnRailSxVoltage; |
| |
| /** Offset 0x04C8 - External Vnn Icc Max Value that will be used in Sx states |
| Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting |
| is 1mA and maximal possible value is 200mA |
| **/ |
| UINT8 PchFivrExtVnnRailSxIccMax; |
| |
| /** Offset 0x04C9 - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage |
| This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX |
| to low current mode voltage. |
| **/ |
| UINT8 PchFivrVccinAuxLowToHighCurModeVolTranTime; |
| |
| /** Offset 0x04CA - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage |
| This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX |
| to retention mode voltage. |
| **/ |
| UINT8 PchFivrVccinAuxRetToHighCurModeVolTranTime; |
| |
| /** Offset 0x04CB - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage |
| This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX |
| to retention mode voltage. |
| **/ |
| UINT8 PchFivrVccinAuxRetToLowCurModeVolTranTime; |
| |
| /** Offset 0x04CC - Transition time in microseconds from Off (0V) to High Current Mode Voltage |
| This field has 1us resolution. When value is 0 Transition to 0V is disabled. |
| **/ |
| UINT16 PchFivrVccinAuxOffToHighCurModeVolTranTime; |
| |
| /** Offset 0x04CE - PMC Debug Message Enable |
| When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW |
| will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix |
| $EN_DIS |
| **/ |
| UINT8 PmcDbgMsgEn; |
| |
| /** Offset 0x04CF - Reserved |
| **/ |
| UINT8 Reserved17; |
| |
| /** Offset 0x04D0 - Pointer to ChipsetInit Binary |
| ChipsetInit Binary Pointer. |
| **/ |
| UINT32 ChipsetInitBinPtr; |
| |
| /** Offset 0x04D4 - Length of ChipsetInit Binary |
| ChipsetInit Binary Length. |
| **/ |
| UINT32 ChipsetInitBinLen; |
| |
| /** Offset 0x04D8 - Reserved |
| **/ |
| UINT8 Reserved18[16]; |
| |
| /** Offset 0x04E8 - FIVR Dynamic Power Management |
| Enable/Disable FIVR Dynamic Power Management. |
| $EN_DIS |
| **/ |
| UINT8 PchFivrDynPm; |
| |
| /** Offset 0x04E9 - Reserved |
| **/ |
| UINT8 Reserved19; |
| |
| /** Offset 0x04EA - External V1P05 Icc Max Value |
| Granularity of this setting is 1mA and maximal possible value is 500mA |
| **/ |
| UINT16 PchFivrExtV1p05RailIccMaximum; |
| |
| /** Offset 0x04EC - External Vnn Icc Max Value that will be used in S0ix/Sx states |
| Granularity of this setting is 1mA and maximal possible value is 500mA |
| **/ |
| UINT16 PchFivrExtVnnRailIccMaximum; |
| |
| /** Offset 0x04EE - External Vnn Icc Max Value that will be used in Sx states |
| Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting |
| is 1mA and maximal possible value is 500mA |
| **/ |
| UINT16 PchFivrExtVnnRailSxIccMaximum; |
| |
| /** Offset 0x04F0 - Reserved |
| **/ |
| UINT8 Reserved20[14]; |
| |
| /** Offset 0x04FE - CNVi Configuration |
| This option allows for automatic detection of Connectivity Solution. [Auto Detection] |
| assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi. |
| 0:Disable, 1:Auto |
| **/ |
| UINT8 CnviMode; |
| |
| /** Offset 0x04FF - CNVi Wi-Fi Core |
| Enable/Disable CNVi Wi-Fi Core, Default is ENABLE. 0: DISABLE, 1: ENABLE |
| $EN_DIS |
| **/ |
| UINT8 CnviWifiCore; |
| |
| /** Offset 0x0500 - CNVi BT Core |
| Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE |
| $EN_DIS |
| **/ |
| UINT8 CnviBtCore; |
| |
| /** Offset 0x0501 - CNVi BT Audio Offload |
| Enable/Disable BT Audio Offload, Default is ENABLE. 0: DISABLE, 1: ENABLE |
| $EN_DIS |
| **/ |
| UINT8 CnviBtAudioOffload; |
| |
| /** Offset 0x0502 - Reserved |
| **/ |
| UINT8 Reserved21[2]; |
| |
| /** Offset 0x0504 - CNVi RF_RESET pin muxing |
| Select CNVi RF_RESET# pin depending on board routing. LP/P/M: GPP_A8 = 0x2942E408(default) |
| or GPP_F4 = 0x194CE404. H/S: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h. |
| **/ |
| UINT32 CnviRfResetPinMux; |
| |
| /** Offset 0x0508 - CNVi CLKREQ pin muxing |
| Select CNVi CLKREQ pin depending on board routing. LP/P/M: GPP_A9 = 0x3942E609(default) |
| or GPP_F5 = 0x394CE605. H/S: 0. Refer to GPIO_*_MUXING_CNVI_CRF_XTAL_CLKREQ_* in |
| GpioPins*.h. |
| **/ |
| UINT32 CnviClkreqPinMux; |
| |
| /** Offset 0x050C - Enable Host C10 reporting through eSPI |
| Enable/disable Host C10 reporting to Device via eSPI Virtual Wire. |
| $EN_DIS |
| **/ |
| UINT8 PchEspiHostC10ReportEnable; |
| |
| /** Offset 0x050D - PCH USB2 PHY Power Gating enable |
| 1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY |
| Sus Well PG |
| $EN_DIS |
| **/ |
| UINT8 PmcUsb2PhySusPgEnable; |
| |
| /** Offset 0x050E - PCH USB OverCurrent mapping enable |
| 1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin |
| mapping allow for NOA usage of OC pins |
| $EN_DIS |
| **/ |
| UINT8 PchUsbOverCurrentEnable; |
| |
| /** Offset 0x050F - Espi Lgmr Memory Range decode |
| This option enables or disables espi lgmr |
| $EN_DIS |
| **/ |
| UINT8 PchEspiLgmrEnable; |
| |
| /** Offset 0x0510 - External V1P05 Control Ramp Timer value |
| Hold off time to be used when changing the v1p05_ctrl for external bypass value in us |
| **/ |
| UINT8 PchFivrExtV1p05RailCtrlRampTmr; |
| |
| /** Offset 0x0511 - External VNN Control Ramp Timer value |
| Hold off time to be used when changing the vnn_ctrl for external bypass value in us |
| **/ |
| UINT8 PchFivrExtVnnRailCtrlRampTmr; |
| |
| /** Offset 0x0512 - Set SATA DEVSLP GPIO Reset Config |
| Set SATA DEVSLP GPIO Reset Config per port. 0x00 - GpioResetDefault, 0x01 - GpioResumeReset, |
| 0x03 - GpioHostDeepReset, 0x05 - GpioPlatformReset, 0x07 - GpioDswReset. One byte |
| for each port, byte0 for port0, byte1 for port1, and so on. |
| **/ |
| UINT8 SataPortsDevSlpResetConfig[8]; |
| |
| /** Offset 0x051A - PCHHOT# pin |
| Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 PchHotEnable; |
| |
| /** Offset 0x051B - SATA LED |
| SATA LED indicating SATA controller activity. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 SataLedEnable; |
| |
| /** Offset 0x051C - VRAlert# Pin |
| When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling |
| to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 PchPmVrAlert; |
| |
| /** Offset 0x051D - AMT Switch |
| Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality. |
| $EN_DIS |
| **/ |
| UINT8 AmtEnabled; |
| |
| /** Offset 0x051E - WatchDog Timer Switch |
| Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting |
| is invalid if AmtEnabled is 0. |
| $EN_DIS |
| **/ |
| UINT8 WatchDogEnabled; |
| |
| /** Offset 0x051F - PET Progress |
| Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive |
| PET Events. Setting is invalid if AmtEnabled is 0. |
| $EN_DIS |
| **/ |
| UINT8 FwProgress; |
| |
| /** Offset 0x0520 - SOL Switch |
| Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx. |
| Setting is invalid if AmtEnabled is 0. |
| $EN_DIS |
| **/ |
| UINT8 AmtSolEnabled; |
| |
| /** Offset 0x0521 - Reserved |
| **/ |
| UINT8 Reserved22; |
| |
| /** Offset 0x0522 - OS Timer |
| 16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0. |
| **/ |
| UINT16 WatchDogTimerOs; |
| |
| /** Offset 0x0524 - BIOS Timer |
| 16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0. |
| **/ |
| UINT16 WatchDogTimerBios; |
| |
| /** Offset 0x0526 - PCH PCIe root port connection type |
| 0: built-in device, 1:slot |
| **/ |
| UINT8 PcieRpSlotImplemented[29]; |
| |
| /** Offset 0x0543 - PCIE RP Access Control Services Extended Capability |
| Enable/Disable PCIE RP Access Control Services Extended Capability |
| **/ |
| UINT8 PcieRpAcsEnabled[29]; |
| |
| /** Offset 0x0560 - PCIE RP Clock Power Management |
| Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal |
| can still be controlled by L1 PM substates mechanism |
| **/ |
| UINT8 PcieRpEnableCpm[29]; |
| |
| /** Offset 0x057D - Reserved |
| **/ |
| UINT8 Reserved23[3]; |
| |
| /** Offset 0x0580 - PCIE RP Detect Timeout Ms |
| The number of milliseconds within 0~65535 in reference code will wait for link to |
| exit Detect state for enabled ports before assuming there is no device and potentially |
| disabling the port. |
| **/ |
| UINT16 PcieRpDetectTimeoutMs[29]; |
| |
| /** Offset 0x05BA - ModPHY SUS Power Domain Dynamic Gating |
| Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on |
| PCH-H. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 PmcModPhySusPgEnable; |
| |
| /** Offset 0x05BB - V1p05-PHY supply external FET control |
| Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY |
| supply. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 PmcV1p05PhyExtFetControlEn; |
| |
| /** Offset 0x05BC - V1p05-IS supply external FET control |
| Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS |
| supply. 0: disable, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 PmcV1p05IsExtFetControlEn; |
| |
| /** Offset 0x05BD - Enable/Disable PavpEnable |
| Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable |
| $EN_DIS |
| **/ |
| UINT8 PavpEnable; |
| |
| /** Offset 0x05BE - Enable/Disable PeiGraphicsPeimInit |
| <b>Enable(Default):</b> FSP will initialize the framebuffer and provide it via EFI_PEI_GRAPHICS_INFO_HOB. |
| Disable: FSP will NOT initialize the framebuffer. |
| $EN_DIS |
| **/ |
| UINT8 PeiGraphicsPeimInit; |
| |
| /** Offset 0x05BF - Enable D3 Hot in TCSS |
| This policy will enable/disable D3 hot support in IOM |
| $EN_DIS |
| **/ |
| UINT8 D3HotEnable; |
| |
| /** Offset 0x05C0 - Enable or disable GNA device |
| 0=Disable, 1(Default)=Enable |
| $EN_DIS |
| **/ |
| UINT8 GnaEnable; |
| |
| /** Offset 0x05C1 - Reserved |
| **/ |
| UINT8 Reserved24[3]; |
| |
| /** Offset 0x05C4 - TypeC port GPIO setting |
| GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined |
| in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Mtl |
| = MeteorLake) |
| **/ |
| UINT32 IomTypeCPortPadCfg[12]; |
| |
| /** Offset 0x05F4 - CPU USB3 Port Over Current Pin |
| Describe the specific over current pin number of USBC Port N. |
| **/ |
| UINT8 CpuUsb3OverCurrentPin[8]; |
| |
| /** Offset 0x05FC - Enable D3 Cold in TCSS |
| This policy will enable/disable D3 cold support in IOM |
| $EN_DIS |
| **/ |
| UINT8 D3ColdEnable; |
| |
| /** Offset 0x05FD - Enable/Disable PCIe tunneling for USB4 |
| Enable/Disable PCIe tunneling for USB4, default is enable |
| $EN_DIS |
| **/ |
| UINT8 ITbtPcieTunnelingForUsb4; |
| |
| /** Offset 0x05FE - Enable/Disable SkipFspGop |
| Enable: Skip FSP provided GOP driver, Disable(Default): Use FSP provided GOP driver |
| $EN_DIS |
| **/ |
| UINT8 SkipFspGop; |
| |
| /** Offset 0x05FF - Enable/Disable VPU Device |
| Enable(Default): Enable VPU Device, Disable: Disable VPU Device |
| $EN_DIS |
| **/ |
| UINT8 VpuEnable; |
| |
| /** Offset 0x0600 - TC State in TCSS |
| This TC C-State Limit in IOM |
| **/ |
| UINT8 TcCstateLimit; |
| |
| /** Offset 0x0601 - Reserved |
| **/ |
| UINT8 Reserved25[3]; |
| |
| /** Offset 0x0604 - Intel Graphics VBT (Video BIOS Table) Size |
| Size of Internal Graphics VBT Image |
| **/ |
| UINT32 VbtSize; |
| |
| /** Offset 0x0608 - Platform LID Status for LFP Displays. |
| LFP Display Lid Status (LID_STATUS enum): 0 (Default): LidClosed, 1: LidOpen. |
| 0: LidClosed, 1: LidOpen |
| **/ |
| UINT8 LidStatus; |
| |
| /** Offset 0x0609 - Reserved |
| **/ |
| UINT8 Reserved26[8]; |
| |
| /** Offset 0x0611 - Enable VMD controller |
| Enable/disable to VMD controller.0: Disable; 1: Enable(Default) |
| $EN_DIS |
| **/ |
| UINT8 VmdEnable; |
| |
| /** Offset 0x0612 - Enable VMD Global Mapping |
| Enable/disable to VMD controller.0: Disable(Default); 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 VmdGlobalMapping; |
| |
| /** Offset 0x0613 - Map port under VMD |
| Map/UnMap port under VMD |
| $EN_DIS |
| **/ |
| UINT8 VmdPort[31]; |
| |
| /** Offset 0x0632 - Reserved |
| **/ |
| UINT8 Reserved27[31]; |
| |
| /** Offset 0x0651 - VMD Port Device |
| VMD Root port device number. |
| **/ |
| UINT8 VmdPortDev[31]; |
| |
| /** Offset 0x0670 - VMD Port Func |
| VMD Root port function number. |
| **/ |
| UINT8 VmdPortFunc[31]; |
| |
| /** Offset 0x068F - Reserved |
| **/ |
| UINT8 Reserved28; |
| |
| /** Offset 0x0690 - VMD Variable |
| VMD Variable Pointer. |
| **/ |
| UINT32 VmdVariablePtr; |
| |
| /** Offset 0x0694 - Temporary CfgBar address for VMD |
| VMD Variable Pointer. |
| **/ |
| UINT32 VmdCfgBarBase; |
| |
| /** Offset 0x0698 - Temporary MemBar1 address for VMD |
| VMD Variable Pointer. |
| **/ |
| UINT32 VmdMemBar1Base; |
| |
| /** Offset 0x069C - Temporary MemBar2 address for VMD |
| VMD Variable Pointer. |
| **/ |
| UINT32 VmdMemBar2Base; |
| |
| /** Offset 0x06A0 - Reserved |
| **/ |
| UINT8 Reserved29; |
| |
| /** Offset 0x06A1 - Enable/Disable PMC-PD Solution |
| This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution |
| $EN_DIS |
| **/ |
| UINT8 PmcPdEnable; |
| |
| /** Offset 0x06A2 - TCSS Aux Orientation Override Enable |
| Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides |
| **/ |
| UINT16 TcssAuxOri; |
| |
| /** Offset 0x06A4 - TCSS HSL Orientation Override Enable |
| Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides |
| **/ |
| UINT16 TcssHslOri; |
| |
| /** Offset 0x06A6 - USB override in IOM |
| This policy will enable/disable USB Connect override in IOM |
| $EN_DIS |
| **/ |
| UINT8 UsbOverride; |
| |
| /** Offset 0x06A7 - ITBT Root Port Enable |
| ITBT Root Port Enable, 0:Disable, 1:Enable |
| 0:Disable, 1:Enable |
| **/ |
| UINT8 ITbtPcieRootPortEn[4]; |
| |
| /** Offset 0x06AB - TCSS USB Port Enable |
| Bits 0, 1, ... max Type C port control enables |
| **/ |
| UINT8 UsbTcPortEn; |
| |
| /** Offset 0x06AC - ITBTForcePowerOn Timeout value |
| ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000. |
| 100 = 100 ms. |
| **/ |
| UINT16 ITbtForcePowerOnTimeoutInMs; |
| |
| /** Offset 0x06AE - ITbtConnectTopology Timeout value |
| ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range |
| is 0-10000. 100 = 100 ms. |
| **/ |
| UINT16 ITbtConnectTopologyTimeoutInMs; |
| |
| /** Offset 0x06B0 - VCCST request for IOM |
| This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5 |
| $EN_DIS |
| **/ |
| UINT8 VccSt; |
| |
| /** Offset 0x06B1 - Reserved |
| **/ |
| UINT8 Reserved30; |
| |
| /** Offset 0x06B2 - ITBT DMA LTR |
| TCSS DMA1, DMA2 LTR value |
| **/ |
| UINT16 ITbtDmaLtr[2]; |
| |
| /** Offset 0x06B6 - Reserved |
| **/ |
| UINT8 Reserved31; |
| |
| /** Offset 0x06B7 - Enable/Disable PTM |
| This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports |
| $EN_DIS |
| **/ |
| UINT8 PtmEnabled[4]; |
| |
| /** Offset 0x06BB - PCIE RP Ltr Enable |
| Latency Tolerance Reporting Mechanism. |
| **/ |
| UINT8 SaPcieItbtRpLtrEnable[4]; |
| |
| /** Offset 0x06BF - PCIE RP Snoop Latency Override Mode |
| Latency Tolerance Reporting, Snoop Latency Override Mode. |
| **/ |
| UINT8 SaPcieItbtRpSnoopLatencyOverrideMode[4]; |
| |
| /** Offset 0x06C3 - PCIE RP Snoop Latency Override Multiplier |
| Latency Tolerance Reporting, Snoop Latency Override Multiplier. |
| **/ |
| UINT8 SaPcieItbtRpSnoopLatencyOverrideMultiplier[4]; |
| |
| /** Offset 0x06C7 - Reserved |
| **/ |
| UINT8 Reserved32; |
| |
| /** Offset 0x06C8 - PCIE RP Snoop Latency Override Value |
| Latency Tolerance Reporting, Snoop Latency Override Value. |
| **/ |
| UINT16 SaPcieItbtRpSnoopLatencyOverrideValue[4]; |
| |
| /** Offset 0x06D0 - PCIE RP Non Snoop Latency Override Mode |
| Latency Tolerance Reporting, Non-Snoop Latency Override Mode. |
| **/ |
| UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMode[4]; |
| |
| /** Offset 0x06D4 - PCIE RP Non Snoop Latency Override Multiplier |
| Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. |
| **/ |
| UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4]; |
| |
| /** Offset 0x06D8 - PCIE RP Non Snoop Latency Override Value |
| Latency Tolerance Reporting, Non-Snoop Latency Override Value. |
| **/ |
| UINT16 SaPcieItbtRpNonSnoopLatencyOverrideValue[4]; |
| |
| /** Offset 0x06E0 - Force LTR Override |
| Force LTR Override. |
| **/ |
| UINT8 SaPcieItbtRpForceLtrOverride[4]; |
| |
| /** Offset 0x06E4 - PCIE RP Ltr Config Lock |
| 0: Disable; 1: Enable. |
| **/ |
| UINT8 SaPcieItbtRpLtrConfigLock[4]; |
| |
| /** Offset 0x06E8 - Enable or Disable TXT |
| Enables utilization of additional hardware capabilities provided by Intel (R) Trusted |
| Execution Technology. Changes require a full power cycle to take effect. <b>0: |
| Disable</b>, 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 TxtEnable; |
| |
| /** Offset 0x06E9 - Reserved |
| **/ |
| UINT8 Reserved33[3]; |
| |
| /** Offset 0x06EC - CpuBistData |
| Pointer CPU BIST Data |
| **/ |
| UINT32 CpuBistData; |
| |
| /** Offset 0x06F0 - CpuMpPpi |
| <b>Optional</b> pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI. |
| If not NULL, FSP will use the boot loader's implementation of multiprocessing. |
| See section 5.1.4 of the FSP Integration Guide for more details. |
| **/ |
| UINT32 CpuMpPpi; |
| |
| /** Offset 0x06F4 - Reserved |
| **/ |
| UINT8 Reserved34[4]; |
| |
| /** Offset 0x06F8 - PpinSupport to view Protected Processor Inventory Number |
| PPIN Feature Support to view Protected Processor Inventory Number. Disable to turn |
| off this feature. When 'PPIN Enable Mode' is selected, this shows second option |
| where feature can be enabled based on EOM (End of Manufacturing) flag or it is |
| always enabled |
| 0: Disable, 1: Enable, 2: Auto |
| **/ |
| UINT8 PpinSupport; |
| |
| /** Offset 0x06F9 - Reserved |
| **/ |
| UINT8 Reserved35; |
| |
| /** Offset 0x06FA - Smbios Type4 Max Speed Override |
| Provide the option for platform to override the MaxSpeed field of Smbios Type 4. |
| If this value is not zero, it dominates the field. |
| **/ |
| UINT16 SmbiosType4MaxSpeedOverride; |
| |
| /** Offset 0x06FC - Advanced Encryption Standard (AES) feature |
| Enable or Disable Advanced Encryption Standard (AES) feature; </b>0: Disable; <b>1: Enable |
| $EN_DIS |
| **/ |
| UINT8 AesEnable; |
| |
| /** Offset 0x06FD - AvxDisable |
| Enable/Disable the AVX and AVX2 Instructions |
| 0: Enable, 1: Disable |
| **/ |
| UINT8 AvxDisable; |
| |
| /** Offset 0x06FE - Reserved |
| **/ |
| UINT8 Reserved36[58]; |
| |
| /** Offset 0x0738 - Enable Power Optimizer |
| Enable DMI Power Optimizer on PCH side. |
| $EN_DIS |
| **/ |
| UINT8 PchPwrOptEnable; |
| |
| /** Offset 0x0739 - PCH Flash Protection Ranges Write Enble |
| Write or erase is blocked by hardware. |
| **/ |
| UINT8 PchWriteProtectionEnable[5]; |
| |
| /** Offset 0x073E - PCH Flash Protection Ranges Read Enble |
| Read is blocked by hardware. |
| **/ |
| UINT8 PchReadProtectionEnable[5]; |
| |
| /** Offset 0x0743 - Reserved |
| **/ |
| UINT8 Reserved37; |
| |
| /** Offset 0x0744 - PCH Protect Range Limit |
| Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for |
| limit comparison. |
| **/ |
| UINT16 PchProtectedRangeLimit[5]; |
| |
| /** Offset 0x074E - PCH Protect Range Base |
| Left shifted address by 12 bits with address bits 11:0 are assumed to be 0. |
| **/ |
| UINT16 PchProtectedRangeBase[5]; |
| |
| /** Offset 0x0758 - Enable Pme |
| Enable Azalia wake-on-ring. |
| $EN_DIS |
| **/ |
| UINT8 PchHdaPme; |
| |
| /** Offset 0x0759 - HD Audio Link Frequency |
| HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz. |
| 0: 6MHz, 1: 12MHz, 2: 24MHz |
| **/ |
| UINT8 PchHdaLinkFrequency; |
| |
| /** Offset 0x075A - Enable PCH ISH SPI Cs0 pins assigned |
| Set if ISH SPI Cs0 pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshSpiCs0Enable[1]; |
| |
| /** Offset 0x075B - Enable PCH Io Apic Entry 24-119 |
| 0: Disable; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 PchIoApicEntry24_119; |
| |
| /** Offset 0x075C - PCH Io Apic ID |
| This member determines IOAPIC ID. Default is 0x02. |
| **/ |
| UINT8 PchIoApicId; |
| |
| /** Offset 0x075D - Enable PCH ISH SPI pins assigned |
| Set if ISH SPI native pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshSpiEnable[1]; |
| |
| /** Offset 0x075E - Enable PCH ISH UART pins assigned |
| Set if ISH UART native pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshUartEnable[2]; |
| |
| /** Offset 0x0760 - Enable PCH ISH I2C pins assigned |
| Set if ISH I2C native pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshI2cEnable[3]; |
| |
| /** Offset 0x0763 - Enable PCH ISH I3C pins assigned |
| Set if ISH I3C native pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshI3cEnable; |
| |
| /** Offset 0x0764 - Enable PCH ISH GP pins assigned |
| Set if ISH GP native pins are to be enabled by BIOS. 0: Disable; 1: Enable. |
| **/ |
| UINT8 PchIshGpEnable[12]; |
| |
| /** Offset 0x0770 - PCH ISH PDT Unlock Msg |
| 0: False; 1: True. |
| $EN_DIS |
| **/ |
| UINT8 PchIshPdtUnlock; |
| |
| /** Offset 0x0771 - Reserved |
| **/ |
| UINT8 Reserved38; |
| |
| /** Offset 0x0772 - Enable PCH Lan LTR capabilty of PCH internal LAN |
| 0: Disable; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 PchLanLtrEnable; |
| |
| /** Offset 0x0773 - Enable LOCKDOWN BIOS LOCK |
| Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region |
| protection. |
| $EN_DIS |
| **/ |
| UINT8 PchLockDownBiosLock; |
| |
| /** Offset 0x0774 - PCH Compatibility Revision ID |
| This member describes whether or not the CRID feature of PCH should be enabled. |
| $EN_DIS |
| **/ |
| UINT8 PchCrid; |
| |
| /** Offset 0x0775 - RTC BIOS Interface Lock |
| Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed. |
| $EN_DIS |
| **/ |
| UINT8 RtcBiosInterfaceLock; |
| |
| /** Offset 0x0776 - RTC Cmos Memory Lock |
| Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper |
| and and lower 128-byte bank of RTC RAM. |
| $EN_DIS |
| **/ |
| UINT8 RtcMemoryLock; |
| |
| /** Offset 0x0777 - Enable PCIE RP HotPlug |
| Indicate whether the root port is hot plug available. |
| **/ |
| UINT8 PcieRpHotPlug[29]; |
| |
| /** Offset 0x0794 - Enable PCIE RP Pm Sci |
| Indicate whether the root port power manager SCI is enabled. |
| $EN_DIS |
| **/ |
| UINT8 PcieRpPmSci[29]; |
| |
| /** Offset 0x07B1 - Enable PCIE RP Transmitter Half Swing |
| Indicate whether the Transmitter Half Swing is enabled. |
| **/ |
| UINT8 PcieRpTransmitterHalfSwing[29]; |
| |
| /** Offset 0x07CE - Enable PCIE RP Clk Req Detect |
| Probe CLKREQ# signal before enabling CLKREQ# based power management. |
| **/ |
| UINT8 PcieRpClkReqDetect[29]; |
| |
| /** Offset 0x07EB - PCIE RP Advanced Error Report |
| Indicate whether the Advanced Error Reporting is enabled. |
| **/ |
| UINT8 PcieRpAdvancedErrorReporting[29]; |
| |
| /** Offset 0x0808 - PCIE RP Unsupported Request Report |
| Indicate whether the Unsupported Request Report is enabled. |
| **/ |
| UINT8 PcieRpUnsupportedRequestReport[29]; |
| |
| /** Offset 0x0825 - PCIE RP Fatal Error Report |
| Indicate whether the Fatal Error Report is enabled. |
| **/ |
| UINT8 PcieRpFatalErrorReport[29]; |
| |
| /** Offset 0x0842 - PCIE RP No Fatal Error Report |
| Indicate whether the No Fatal Error Report is enabled. |
| **/ |
| UINT8 PcieRpNoFatalErrorReport[29]; |
| |
| /** Offset 0x085F - PCIE RP Correctable Error Report |
| Indicate whether the Correctable Error Report is enabled. |
| **/ |
| UINT8 PcieRpCorrectableErrorReport[29]; |
| |
| /** Offset 0x087C - PCIE RP System Error On Fatal Error |
| Indicate whether the System Error on Fatal Error is enabled. |
| **/ |
| UINT8 PcieRpSystemErrorOnFatalError[29]; |
| |
| /** Offset 0x0899 - PCIE RP System Error On Non Fatal Error |
| Indicate whether the System Error on Non Fatal Error is enabled. |
| **/ |
| UINT8 PcieRpSystemErrorOnNonFatalError[29]; |
| |
| /** Offset 0x08B6 - PCIE RP System Error On Correctable Error |
| Indicate whether the System Error on Correctable Error is enabled. |
| **/ |
| UINT8 PcieRpSystemErrorOnCorrectableError[29]; |
| |
| /** Offset 0x08D3 - PCIE RP Max Payload |
| Max Payload Size supported, Default 256B, see enum PCH_PCIE_MAX_PAYLOAD. |
| **/ |
| UINT8 PcieRpMaxPayload[29]; |
| |
| /** Offset 0x08F0 - Touch Host Controller Assignment |
| Assign THC 0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0, 0x2:ThcAssignmentThc1 |
| **/ |
| UINT8 ThcAssignment[2]; |
| |
| /** Offset 0x08F2 - Reserved |
| **/ |
| UINT8 Reserved39[122]; |
| |
| /** Offset 0x096C - PCIE RP Pcie Speed |
| Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see: |
| PCIE_SPEED). |
| **/ |
| UINT8 PcieRpPcieSpeed[29]; |
| |
| /** Offset 0x0989 - PCIE RP Physical Slot Number |
| Indicates the slot number for the root port. Default is the value as root port index. |
| **/ |
| UINT8 PcieRpPhysicalSlotNumber[29]; |
| |
| /** Offset 0x09A6 - PCIE RP Completion Timeout |
| The root port completion timeout(see: PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default. |
| **/ |
| UINT8 PcieRpCompletionTimeout[29]; |
| |
| /** Offset 0x09C3 - PCIE RP Aspm |
| The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is |
| PchPcieAspmAutoConfig. |
| **/ |
| UINT8 PcieRpAspm[29]; |
| |
| /** Offset 0x09E0 - PCIE RP L1 Substates |
| The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL). |
| Default is PchPcieL1SubstatesL1_1_2. |
| **/ |
| UINT8 PcieRpL1Substates[29]; |
| |
| /** Offset 0x09FD - PCIE RP Ltr Enable |
| Latency Tolerance Reporting Mechanism. |
| **/ |
| UINT8 PcieRpLtrEnable[29]; |
| |
| /** Offset 0x0A1A - PCIE RP Ltr Config Lock |
| 0: Disable; 1: Enable. |
| **/ |
| UINT8 PcieRpLtrConfigLock[29]; |
| |
| /** Offset 0x0A37 - PCIE RP override default settings for EQ |
| Choose PCIe EQ method |
| $EN_DIS |
| **/ |
| UINT8 PcieEqOverrideDefault[29]; |
| |
| /** Offset 0x0A54 - Reserved |
| **/ |
| UINT8 Reserved40[3767]; |
| |
| /** Offset 0x190B - PCIE RP Enable Peer Memory Write |
| This member describes whether Peer Memory Writes are enabled on the platform. |
| $EN_DIS |
| **/ |
| UINT8 PcieEnablePeerMemoryWrite[12]; |
| |
| /** Offset 0x1917 - PCIE Compliance Test Mode |
| Compliance Test Mode shall be enabled when using Compliance Load Board. |
| $EN_DIS |
| **/ |
| UINT8 PcieComplianceTestMode; |
| |
| /** Offset 0x1918 - PCIE Rp Function Swap |
| Allows BIOS to use root port function number swapping when root port of function |
| 0 is disabled. |
| $EN_DIS |
| **/ |
| UINT8 PcieRpFunctionSwap; |
| |
| /** Offset 0x1919 - Reserved |
| **/ |
| UINT8 Reserved41; |
| |
| /** Offset 0x191A - PCH Pm PME_B0_S5_DIS |
| When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1. |
| $EN_DIS |
| **/ |
| UINT8 PchPmPmeB0S5Dis; |
| |
| /** Offset 0x191B - PCIE IMR |
| Enables Isolated Memory Region for PCIe. |
| $EN_DIS |
| **/ |
| UINT8 PcieRpImrEnabled; |
| |
| /** Offset 0x191C - PCIE IMR port number |
| Selects PCIE root port number for IMR feature. |
| **/ |
| UINT8 PcieRpImrSelection; |
| |
| /** Offset 0x191D - PCH Pm Wol Enable Override |
| Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register. |
| $EN_DIS |
| **/ |
| UINT8 PchPmWolEnableOverride; |
| |
| /** Offset 0x191E - PCH Pm WoW lan Enable |
| Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register. |
| $EN_DIS |
| **/ |
| UINT8 PchPmWoWlanEnable; |
| |
| /** Offset 0x191F - Reserved |
| **/ |
| UINT8 Reserved42[4]; |
| |
| /** Offset 0x1923 - PCH Pm Slp S3 Min Assert |
| SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms. |
| **/ |
| UINT8 PchPmSlpS3MinAssert; |
| |
| /** Offset 0x1924 - PCH Pm Slp S4 Min Assert |
| SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s. |
| **/ |
| UINT8 PchPmSlpS4MinAssert; |
| |
| /** Offset 0x1925 - PCH Pm Slp Sus Min Assert |
| SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s. |
| **/ |
| UINT8 PchPmSlpSusMinAssert; |
| |
| /** Offset 0x1926 - PCH Pm Slp A Min Assert |
| SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s. |
| **/ |
| UINT8 PchPmSlpAMinAssert; |
| |
| /** Offset 0x1927 - USB Overcurrent Override for VISA |
| This option overrides USB Over Current enablement state that USB OC will be disabled |
| after enabling this option. Enable when VISA pin is muxed with USB OC |
| $EN_DIS |
| **/ |
| UINT8 PchEnableDbcObs; |
| |
| /** Offset 0x1928 - PCH Pm Slp Strch Sus Up |
| Enable SLP_X Stretching After SUS Well Power Up. |
| $EN_DIS |
| **/ |
| UINT8 PchPmSlpStrchSusUp; |
| |
| /** Offset 0x1929 - PCH Pm Slp Lan Low Dc |
| Enable/Disable SLP_LAN# Low on DC Power. |
| $EN_DIS |
| **/ |
| UINT8 PchPmSlpLanLowDc; |
| |
| /** Offset 0x192A - PCH Pm Pwr Btn Override Period |
| PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s. |
| **/ |
| UINT8 PchPmPwrBtnOverridePeriod; |
| |
| /** Offset 0x192B - PCH Pm Disable Native Power Button |
| Power button native mode disable. |
| $EN_DIS |
| **/ |
| UINT8 PchPmDisableNativePowerButton; |
| |
| /** Offset 0x192C - PCH Pm ME_WAKE_STS |
| Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register. |
| $EN_DIS |
| **/ |
| UINT8 PchPmMeWakeSts; |
| |
| /** Offset 0x192D - PCH Pm WOL_OVR_WK_STS |
| Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register. |
| $EN_DIS |
| **/ |
| UINT8 PchPmWolOvrWkSts; |
| |
| /** Offset 0x192E - PCH Pm Reset Power Cycle Duration |
| Could be customized in the unit of second. Please refer to EDS for all support settings. |
| 0 is default, 1 is 1 second, 2 is 2 seconds, ... |
| **/ |
| UINT8 PchPmPwrCycDur; |
| |
| /** Offset 0x192F - PCH Pm Pcie Pll Ssc |
| Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No |
| BIOS override. |
| **/ |
| UINT8 PchPmPciePllSsc; |
| |
| /** Offset 0x1930 - PCH Legacy IO Low Latency Enable |
| Set to enable low latency of legacy IO. <b>0: Disable</b>, 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 PchLegacyIoLowLatency; |
| |
| /** Offset 0x1931 - PCH Sata Pwr Opt Enable |
| SATA Power Optimizer on PCH side. |
| $EN_DIS |
| **/ |
| UINT8 SataPwrOptEnable; |
| |
| /** Offset 0x1932 - PCH Sata eSATA Speed Limit |
| When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed. |
| $EN_DIS |
| **/ |
| UINT8 EsataSpeedLimit; |
| |
| /** Offset 0x1933 - PCH Sata Speed Limit |
| Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault. |
| **/ |
| UINT8 SataSpeedLimit; |
| |
| /** Offset 0x1934 - Enable SATA Port HotPlug |
| Enable SATA Port HotPlug. |
| **/ |
| UINT8 SataPortsHotPlug[8]; |
| |
| /** Offset 0x193C - Enable SATA Port Interlock Sw |
| Enable SATA Port Interlock Sw. |
| **/ |
| UINT8 SataPortsInterlockSw[8]; |
| |
| /** Offset 0x1944 - Enable SATA Port External |
| Enable SATA Port External. |
| **/ |
| UINT8 SataPortsExternal[8]; |
| |
| /** Offset 0x194C - Enable SATA Port SpinUp |
| Enable the COMRESET initialization Sequence to the device. |
| **/ |
| UINT8 SataPortsSpinUp[8]; |
| |
| /** Offset 0x1954 - Enable SATA Port Solid State Drive |
| 0: HDD; 1: SSD. |
| **/ |
| UINT8 SataPortsSolidStateDrive[8]; |
| |
| /** Offset 0x195C - Enable SATA Port Enable Dito Config |
| Enable DEVSLP Idle Timeout settings (DmVal, DitoVal). |
| **/ |
| UINT8 SataPortsEnableDitoConfig[8]; |
| |
| /** Offset 0x1964 - Enable SATA Port DmVal |
| DITO multiplier. Default is 15. |
| **/ |
| UINT8 SataPortsDmVal[8]; |
| |
| /** Offset 0x196C - Reserved |
| **/ |
| UINT8 Reserved43[2]; |
| |
| /** Offset 0x196E - Enable SATA Port DmVal |
| DEVSLP Idle Timeout (DITO), Default is 625. |
| **/ |
| UINT16 SataPortsDitoVal[8]; |
| |
| /** Offset 0x197E - Enable SATA Port ZpOdd |
| Support zero power ODD. |
| **/ |
| UINT8 SataPortsZpOdd[8]; |
| |
| /** Offset 0x1986 - PCH Sata Rst Raid Alternate Id |
| Enable RAID Alternate ID. |
| $EN_DIS |
| **/ |
| UINT8 SataRstRaidDeviceId; |
| |
| /** Offset 0x1987 - PCH Sata Rst Pcie Storage Remap enable |
| Enable Intel RST for PCIe Storage remapping. |
| **/ |
| UINT8 SataRstPcieEnable[3]; |
| |
| /** Offset 0x198A - PCH Sata Rst Pcie Storage Port |
| Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect). |
| **/ |
| UINT8 SataRstPcieStoragePort[3]; |
| |
| /** Offset 0x198D - PCH Sata Rst Pcie Device Reset Delay |
| PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms |
| **/ |
| UINT8 SataRstPcieDeviceResetDelay[3]; |
| |
| /** Offset 0x1990 - UFS enable/disable |
| Enable/Disable UFS controller, One byte for each Controller - (1,0) to enable controller |
| 0 and (0,1) to enable controller 1 |
| $EN_DIS |
| **/ |
| UINT8 UfsEnable[2]; |
| |
| /** Offset 0x1992 - Reserved |
| **/ |
| UINT8 Reserved44[2]; |
| |
| /** Offset 0x1994 - IEH Mode |
| Integrated Error Handler Mode, 0: Bypass, 1: Enable |
| 0: Bypass, 1:Enable |
| **/ |
| UINT8 IehMode; |
| |
| /** Offset 0x1995 - Reserved |
| **/ |
| UINT8 Reserved45[11]; |
| |
| /** Offset 0x19A0 - PCH Thermal Throttling Custimized T0Level Value |
| Custimized T0Level value. |
| **/ |
| UINT16 PchT0Level; |
| |
| /** Offset 0x19A2 - PCH Thermal Throttling Custimized T1Level Value |
| Custimized T1Level value. |
| **/ |
| UINT16 PchT1Level; |
| |
| /** Offset 0x19A4 - PCH Thermal Throttling Custimized T2Level Value |
| Custimized T2Level value. |
| **/ |
| UINT16 PchT2Level; |
| |
| /** Offset 0x19A6 - Enable PCH Thermal Throttle |
| Enable thermal throttle function. |
| $EN_DIS |
| **/ |
| UINT8 PchTTEnable; |
| |
| /** Offset 0x19A7 - PCH PMSync State 13 |
| When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force |
| at least T2 state. |
| $EN_DIS |
| **/ |
| UINT8 PchTTState13Enable; |
| |
| /** Offset 0x19A8 - PCH Thermal Throttle Lock |
| Thermal Throttle Lock. |
| $EN_DIS |
| **/ |
| UINT8 PchTTLock; |
| |
| /** Offset 0x19A9 - Reserved |
| **/ |
| UINT8 Reserved46[9]; |
| |
| /** Offset 0x19B2 - DMI Thermal Sensor Autonomous Width Enable |
| DMI Thermal Sensor Autonomous Width Enable. |
| $EN_DIS |
| **/ |
| UINT8 PchDmiTsawEn; |
| |
| /** Offset 0x19B3 - DMI Thermal Sensor Suggested Setting |
| DMT thermal sensor suggested representative values. |
| $EN_DIS |
| **/ |
| UINT8 DmiSuggestedSetting; |
| |
| /** Offset 0x19B4 - Thermal Sensor 0 Target Width |
| Thermal Sensor 0 Target Width. |
| 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 |
| **/ |
| UINT8 DmiTS0TW; |
| |
| /** Offset 0x19B5 - Thermal Sensor 1 Target Width |
| Thermal Sensor 1 Target Width. |
| 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 |
| **/ |
| UINT8 DmiTS1TW; |
| |
| /** Offset 0x19B6 - Thermal Sensor 2 Target Width |
| Thermal Sensor 2 Target Width. |
| 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 |
| **/ |
| UINT8 DmiTS2TW; |
| |
| /** Offset 0x19B7 - Thermal Sensor 3 Target Width |
| Thermal Sensor 3 Target Width. |
| 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 |
| **/ |
| UINT8 DmiTS3TW; |
| |
| /** Offset 0x19B8 - Port 0 T1 Multipler |
| Port 0 T1 Multipler. |
| **/ |
| UINT8 SataP0T1M; |
| |
| /** Offset 0x19B9 - Port 0 T2 Multipler |
| Port 0 T2 Multipler. |
| **/ |
| UINT8 SataP0T2M; |
| |
| /** Offset 0x19BA - Port 0 T3 Multipler |
| Port 0 T3 Multipler. |
| **/ |
| UINT8 SataP0T3M; |
| |
| /** Offset 0x19BB - Port 0 Tdispatch |
| Port 0 Tdispatch. |
| **/ |
| UINT8 SataP0TDisp; |
| |
| /** Offset 0x19BC - Port 1 T1 Multipler |
| Port 1 T1 Multipler. |
| **/ |
| UINT8 SataP1T1M; |
| |
| /** Offset 0x19BD - Port 1 T2 Multipler |
| Port 1 T2 Multipler. |
| **/ |
| UINT8 SataP1T2M; |
| |
| /** Offset 0x19BE - Port 1 T3 Multipler |
| Port 1 T3 Multipler. |
| **/ |
| UINT8 SataP1T3M; |
| |
| /** Offset 0x19BF - Port 1 Tdispatch |
| Port 1 Tdispatch. |
| **/ |
| UINT8 SataP1TDisp; |
| |
| /** Offset 0x19C0 - Port 0 Tinactive |
| Port 0 Tinactive. |
| **/ |
| UINT8 SataP0Tinact; |
| |
| /** Offset 0x19C1 - Port 0 Alternate Fast Init Tdispatch |
| Port 0 Alternate Fast Init Tdispatch. |
| $EN_DIS |
| **/ |
| UINT8 SataP0TDispFinit; |
| |
| /** Offset 0x19C2 - Port 1 Tinactive |
| Port 1 Tinactive. |
| **/ |
| UINT8 SataP1Tinact; |
| |
| /** Offset 0x19C3 - Port 1 Alternate Fast Init Tdispatch |
| Port 1 Alternate Fast Init Tdispatch. |
| $EN_DIS |
| **/ |
| UINT8 SataP1TDispFinit; |
| |
| /** Offset 0x19C4 - Sata Thermal Throttling Suggested Setting |
| Sata Thermal Throttling Suggested Setting. |
| $EN_DIS |
| **/ |
| UINT8 SataThermalSuggestedSetting; |
| |
| /** Offset 0x19C5 - Reserved |
| **/ |
| UINT8 Reserved47; |
| |
| /** Offset 0x19C6 - Thermal Device Temperature |
| Decides the temperature. |
| **/ |
| UINT16 PchTemperatureHotLevel; |
| |
| /** Offset 0x19C8 - USB2 Port Over Current Pin |
| Describe the specific over current pin number of USB 2.0 Port N. |
| **/ |
| UINT8 Usb2OverCurrentPin[16]; |
| |
| /** Offset 0x19D8 - USB3 Port Over Current Pin |
| Describe the specific over current pin number of USB 3.0 Port N. |
| **/ |
| UINT8 Usb3OverCurrentPin[10]; |
| |
| /** Offset 0x19E2 - Enable xHCI LTR override |
| Enables override of recommended LTR values for xHCI |
| $EN_DIS |
| **/ |
| UINT8 PchUsbLtrOverrideEnable; |
| |
| /** Offset 0x19E3 - Reserved |
| **/ |
| UINT8 Reserved48; |
| |
| /** Offset 0x19E4 - xHCI High Idle Time LTR override |
| Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting |
| **/ |
| UINT32 PchUsbLtrHighIdleTimeOverride; |
| |
| /** Offset 0x19E8 - xHCI Medium Idle Time LTR override |
| Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting |
| **/ |
| UINT32 PchUsbLtrMediumIdleTimeOverride; |
| |
| /** Offset 0x19EC - xHCI Low Idle Time LTR override |
| Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting |
| **/ |
| UINT32 PchUsbLtrLowIdleTimeOverride; |
| |
| /** Offset 0x19F0 - Enable 8254 Static Clock Gating |
| Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time |
| might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support |
| legacy OS using 8254 timer. Also enable this while S0ix is enabled. |
| $EN_DIS |
| **/ |
| UINT8 Enable8254ClockGating; |
| |
| /** Offset 0x19F1 - Enable 8254 Static Clock Gating On S3 |
| This is only applicable when Enable8254ClockGating is disabled. FSP will do the |
| 8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This |
| avoids the SMI requirement for the programming. |
| $EN_DIS |
| **/ |
| UINT8 Enable8254ClockGatingOnS3; |
| |
| /** Offset 0x19F2 - Enable TCO timer. |
| When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have |
| huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer |
| emulation must be enabled, and WDAT table must not be exposed to the OS. |
| $EN_DIS |
| **/ |
| UINT8 EnableTcoTimer; |
| |
| /** Offset 0x19F3 - Reserved |
| **/ |
| UINT8 Reserved49[5]; |
| |
| /** Offset 0x19F8 - BgpdtHash[4] |
| BgpdtHash values |
| **/ |
| UINT64 BgpdtHash[4]; |
| |
| /** Offset 0x1A18 - BiosGuardAttr |
| BiosGuardAttr default values |
| **/ |
| UINT32 BiosGuardAttr; |
| |
| /** Offset 0x1A1C - Reserved |
| **/ |
| UINT8 Reserved50[4]; |
| |
| /** Offset 0x1A20 - BiosGuardModulePtr |
| BiosGuardModulePtr default values |
| **/ |
| UINT64 BiosGuardModulePtr; |
| |
| /** Offset 0x1A28 - SendEcCmd |
| SendEcCmd function pointer. \n |
| @code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE |
| EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode |
| **/ |
| UINT64 SendEcCmd; |
| |
| /** Offset 0x1A30 - EcCmdProvisionEav |
| Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC |
| **/ |
| UINT8 EcCmdProvisionEav; |
| |
| /** Offset 0x1A31 - EcCmdLock |
| EcCmdLock default values. Locks Ephemeral Authorization Value sent previously |
| **/ |
| UINT8 EcCmdLock; |
| |
| /** Offset 0x1A32 - Reserved |
| **/ |
| UINT8 Reserved51[22]; |
| |
| /** Offset 0x1A48 - Skip Ssid Programming. |
| When set to TRUE, silicon code will not do any SSID programming and platform code |
| needs to handle that by itself properly. |
| $EN_DIS |
| **/ |
| UINT8 SiSkipSsidProgramming; |
| |
| /** Offset 0x1A49 - Reserved |
| **/ |
| UINT8 Reserved52; |
| |
| /** Offset 0x1A4A - Change Default SVID |
| Change the default SVID used in FSP to programming internal devices. This is only |
| valid when SkipSsidProgramming is FALSE. |
| **/ |
| UINT16 SiCustomizedSvid; |
| |
| /** Offset 0x1A4C - Change Default SSID |
| Change the default SSID used in FSP to programming internal devices. This is only |
| valid when SkipSsidProgramming is FALSE. |
| **/ |
| UINT16 SiCustomizedSsid; |
| |
| /** Offset 0x1A4E - Reserved |
| **/ |
| UINT8 Reserved53[2]; |
| |
| /** Offset 0x1A50 - SVID SDID table Poniter. |
| The address of the table of SVID SDID to customize each SVID SDID entry. This is |
| only valid when SkipSsidProgramming is FALSE. |
| **/ |
| UINT32 SiSsidTablePtr; |
| |
| /** Offset 0x1A54 - Number of ssid table. |
| SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr. |
| This is only valid when SkipSsidProgramming is FALSE. |
| **/ |
| UINT16 SiNumberOfSsidTableEntry; |
| |
| /** Offset 0x1A56 - USB2 Port Reset Message Enable |
| 0: Disable USB2 Port Reset Message; 1: Enable USB2 Port Reset Message; This must |
| be enable for USB2 Port those are paired with CPU XHCI Port |
| **/ |
| UINT8 PortResetMessageEnable[16]; |
| |
| /** Offset 0x1A66 - SATA RST Interrupt Mode |
| Allowes to choose which interrupts will be implemented by SATA controller in RAID mode. |
| 0:Msix, 1:Msi, 2:Legacy |
| **/ |
| UINT8 SataRstInterrupt; |
| |
| /** Offset 0x1A67 - Enable PS_ON. |
| PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power |
| target that will be required by the California Energy Commission (CEC). When FALSE, |
| PS_ON is to be disabled. |
| $EN_DIS |
| **/ |
| UINT8 PsOnEnable; |
| |
| /** Offset 0x1A68 - Pmc Cpu C10 Gate Pin Enable |
| Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO |
| and VccSTG rails instead of SLP_S0# pin. |
| $EN_DIS |
| **/ |
| UINT8 PmcCpuC10GatePinEnable; |
| |
| /** Offset 0x1A69 - Pch Dmi Aspm Ctrl |
| ASPM configuration on the PCH side of the DMI/OPI Link. Default is <b>PchPcieAspmAutoConfig</b> |
| 0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto |
| **/ |
| UINT8 PchDmiAspmCtrl; |
| |
| /** Offset 0x1A6A - PchDmiCwbEnable |
| Central Write Buffer feature configurable and enabled by default |
| $EN_DIS |
| **/ |
| UINT8 PchDmiCwbEnable; |
| |
| /** Offset 0x1A6B - OS IDLE Mode Enable |
| Enable/Disable OS Idle Mode |
| $EN_DIS |
| **/ |
| UINT8 PmcOsIdleEnable; |
| |
| /** Offset 0x1A6C - S0ix Auto-Demotion |
| Enable/Disable the Low Power Mode Auto-Demotion Host Control feature. |
| $EN_DIS |
| **/ |
| UINT8 PchS0ixAutoDemotion; |
| |
| /** Offset 0x1A6D - Latch Events C10 Exit |
| When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are |
| captured on C10 exit (instead of C10 entry which is default) |
| $EN_DIS |
| **/ |
| UINT8 PchPmLatchEventsC10Exit; |
| |
| /** Offset 0x1A6E - Reserved |
| **/ |
| UINT8 Reserved54[127]; |
| |
| /** Offset 0x1AED - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3 |
| Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each |
| value in array can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate3UniqTranEnable[10]; |
| |
| /** Offset 0x1AF7 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3 |
| USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], <b>Default |
| = 4Ch</b>. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate3UniqTran[10]; |
| |
| /** Offset 0x1B01 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2 |
| Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each |
| value in array can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate2UniqTranEnable[10]; |
| |
| /** Offset 0x1B0B - USB 3.0 TX Output Unique Transition Bit Scale for rate 2 |
| USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8], |
| <b>Default = 4Ch</b>. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate2UniqTran[10]; |
| |
| /** Offset 0x1B15 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1 |
| Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each |
| value in array can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate1UniqTranEnable[10]; |
| |
| /** Offset 0x1B1F - USB 3.0 TX Output Unique Transition Bit Scale for rate 1 |
| USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16], |
| <b>Default = 4Ch</b>. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate1UniqTran[10]; |
| |
| /** Offset 0x1B29 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0 |
| Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each |
| value in array can be between 0-1. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate0UniqTranEnable[10]; |
| |
| /** Offset 0x1B33 - USB 3.0 TX Output Unique Transition Bit Scale for rate 0 |
| USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24], |
| <b>Default = 4Ch</b>. One byte for each port. |
| **/ |
| UINT8 Usb3HsioTxRate0UniqTran[10]; |
| |
| /** Offset 0x1B3D - Skip PAM regsiter lock |
| Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default): |
| PAM registers will be locked by RC |
| $EN_DIS |
| **/ |
| UINT8 SkipPamLock; |
| |
| /** Offset 0x1B3E - Enable/Disable IGFX RenderStandby |
| Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby |
| $EN_DIS |
| **/ |
| UINT8 RenderStandby; |
| |
| /** Offset 0x1B3F - Reserved |
| **/ |
| UINT8 Reserved55; |
| |
| /** Offset 0x1B40 - GT Frequency Limit |
| 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, |
| 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: |
| 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, |
| 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, |
| 0x18: 1200 Mhz |
| 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, |
| 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: |
| 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, |
| 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, |
| 0x18: 1200 Mhz |
| **/ |
| UINT8 GtFreqMax; |
| |
| /** Offset 0x1B41 - Disable Turbo GT |
| 0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency |
| $EN_DIS |
| **/ |
| UINT8 DisableTurboGt; |
| |
| /** Offset 0x1B42 - Reserved |
| **/ |
| UINT8 Reserved56[2]; |
| |
| /** Offset 0x1B44 - Enable TSN Multi-VC |
| Enable/disable Multi Virtual Channels(VC) in TSN. |
| $EN_DIS |
| **/ |
| UINT8 PchTsnMultiVcEnable; |
| |
| /** Offset 0x1B45 - Reserved |
| **/ |
| UINT8 Reserved57[11]; |
| |
| /** Offset 0x1B50 - LogoPixelHeight Address |
| Address of LogoPixelHeight |
| **/ |
| UINT32 LogoPixelHeight; |
| |
| /** Offset 0x1B54 - LogoPixelWidth Address |
| Address of LogoPixelWidth |
| **/ |
| UINT32 LogoPixelWidth; |
| |
| /** Offset 0x1B58 - Reserved |
| **/ |
| UINT8 Reserved58; |
| |
| /** Offset 0x1B59 - ITbt Usb4CmMode value |
| ITbt Usb4CmMode value. 0:Firmware CM, 1:Software CM |
| **/ |
| UINT8 Usb4CmMode; |
| |
| /** Offset 0x1B5A - Reserved |
| **/ |
| UINT8 Reserved59[75]; |
| |
| /** Offset 0x1BA5 - RSR feature |
| Enable or Disable RSR feature; 0: Disable; <b>1: Enable </b> |
| $EN_DIS |
| **/ |
| UINT8 EnableRsr; |
| |
| /** Offset 0x1BA6 - Reserved |
| **/ |
| UINT8 Reserved60[4]; |
| |
| /** Offset 0x1BAA - Enable or Disable HWP |
| Enable/Disable Intel(R) Speed Shift Technology support. Enabling will expose the |
| CPPC v2 interface to allow for hardware controlled P-states. 0: Disable; <b>1: |
| Enable;</b> |
| $EN_DIS |
| **/ |
| UINT8 Hwp; |
| |
| /** Offset 0x1BAB - Package Long duration turbo mode time |
| Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 |
| = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window |
| which Processor Base Power (TDP) value should be maintained. Valid values(Unit |
| in seconds) 0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , |
| 80 , 96 , 112 , 128 |
| **/ |
| UINT8 PowerLimit1Time; |
| |
| /** Offset 0x1BAC - Short Duration Turbo Mode |
| Enable/Disable Power Limit 2 override. If this option is disabled, BIOS will program |
| the default values for Power Limit 2. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 PowerLimit2; |
| |
| /** Offset 0x1BAD - Turbo settings Lock |
| Enable/Disable locking of Package Power Limit settings. When enabled, PACKAGE_POWER_LIMIT |
| MSR will be locked and a reset will be required to unlock the register. <b>0: Disable; |
| </b> 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 TurboPowerLimitLock; |
| |
| /** Offset 0x1BAE - Package PL3 time window |
| Power Limit 3 Time Window value in Milli seconds. Indicates the time window over |
| which Power Limit 3 value should be maintained. If the value is 0, BIOS leaves |
| the hardware default value. Valid value: <b>0</b>, 3-8, 10, 12, 14, 16, 20, 24, |
| 28, 32, 40, 48, 56, 64. |
| **/ |
| UINT8 PowerLimit3Time; |
| |
| /** Offset 0x1BAF - Package PL3 Duty Cycle |
| Specify the duty cycle in percentage that the CPU is required to maintain over the |
| configured time window. Range is 0-100. |
| **/ |
| UINT8 PowerLimit3DutyCycle; |
| |
| /** Offset 0x1BB0 - Package PL3 Lock |
| Power Limit 3 Lock. When enabled PL3 configurations are locked during OS. When disabled |
| PL3 configuration can be changed during OS. <b>0: Disable</b> ; 1:Enable |
| $EN_DIS |
| **/ |
| UINT8 PowerLimit3Lock; |
| |
| /** Offset 0x1BB1 - Package PL4 Lock |
| Power Limit 4 Lock. When enabled PL4 configurations are locked during OS. When disabled |
| PL4 configuration can be changed during OS. <b>0: Disable</b> ; 1:Enable |
| $EN_DIS |
| **/ |
| UINT8 PowerLimit4Lock; |
| |
| /** Offset 0x1BB2 - TCC Activation Offset |
| TCC Activation Offset. Offset from factory set TCC activation temperature at which |
| the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation |
| Temperature, in volts. <b>Default = 0h</b>. |
| **/ |
| UINT8 TccActivationOffset; |
| |
| /** Offset 0x1BB3 - Tcc Offset Clamp Enable/Disable |
| Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle |
| below P1. <b>0: Disabled</b>; 1: Enabled. |
| $EN_DIS |
| **/ |
| UINT8 TccOffsetClamp; |
| |
| /** Offset 0x1BB4 - Tcc Offset Lock |
| Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature |
| target; <b>0: Disabled</b>; 1: Enabled. |
| $EN_DIS |
| **/ |
| UINT8 TccOffsetLock; |
| |
| /** Offset 0x1BB5 - Custom Ratio State Entries |
| The number of custom ratio state entries, ranges from 0 to 40 for a valid custom |
| ratio table. Sets the number of custom P-states. At least 2 states must be present |
| **/ |
| UINT8 NumberOfEntries; |
| |
| /** Offset 0x1BB6 - Custom Short term Power Limit time window |
| Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 |
| = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window |
| which Processor Base Power (TDP) value should be maintained. |
| **/ |
| UINT8 Custom1PowerLimit1Time; |
| |
| /** Offset 0x1BB7 - Custom Turbo Activation Ratio |
| Custom value for Turbo Activation Ratio. Needs to be configured with valid values |
| from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255 |
| **/ |
| UINT8 Custom1TurboActivationRatio; |
| |
| /** Offset 0x1BB8 - Custom Config Tdp Control |
| Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level |
| 1. Valid Range is 0 to 2 |
| **/ |
| UINT8 Custom1ConfigTdpControl; |
| |
| /** Offset 0x1BB9 - Custom Short term Power Limit time window |
| Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 |
| = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window |
| which Processor Base Power (TDP) value should be maintained. |
| **/ |
| UINT8 Custom2PowerLimit1Time; |
| |
| /** Offset 0x1BBA - Custom Turbo Activation Ratio |
| Custom value for Turbo Activation Ratio. Needs to be configured with valid values |
| from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255 |
| **/ |
| UINT8 Custom2TurboActivationRatio; |
| |
| /** Offset 0x1BBB - Custom Config Tdp Control |
| Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level |
| 1. Valid Range is 0 to 2 |
| **/ |
| UINT8 Custom2ConfigTdpControl; |
| |
| /** Offset 0x1BBC - Custom Short term Power Limit time window |
| Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 |
| = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window |
| which Processor Base Power (TDP) value should be maintained. |
| **/ |
| UINT8 Custom3PowerLimit1Time; |
| |
| /** Offset 0x1BBD - Custom Turbo Activation Ratio |
| Custom value for Turbo Activation Ratio. Needs to be configured with valid values |
| from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255 |
| **/ |
| UINT8 Custom3TurboActivationRatio; |
| |
| /** Offset 0x1BBE - Custom Config Tdp Control |
| Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level |
| 1. Valid Range is 0 to 2 |
| **/ |
| UINT8 Custom3ConfigTdpControl; |
| |
| /** Offset 0x1BBF - ConfigTdp mode settings Lock |
| cTDP(Assured Power) Mode Lock sets the Lock bits on TURBO_ACTIVATION_RATIO and CONFIG_TDP_CONTROL. |
| Note: When CTDP(Assured Power) Lock is enabled Custom ConfigTDP Count will be forced |
| to 1 and Custom ConfigTDP Boot Index will be forced to 0. <b>0: Disable</b>; 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 ConfigTdpLock; |
| |
| /** Offset 0x1BC0 - Load Configurable TDP SSDT |
| Enables cTDP(Assured Power) control via runtime ACPI BIOS methods. This 'BIOS only' |
| feature does not require EC or driver support. <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 ConfigTdpBios; |
| |
| /** Offset 0x1BC1 - PL1 Enable value |
| Enable/Disable Platform Power Limit 1 programming. If this option is enabled, it |
| activates the PL1 value to be used by the processor to limit the average power |
| of given time window. <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 PsysPowerLimit1; |
| |
| /** Offset 0x1BC2 - PL1 timewindow |
| Platform Power Limit 1 Time Window value in seconds. The value may vary from 0 to |
| 128. 0 = default values. Indicates the time window over which Platform Processor |
| Base Power (TDP) value should be maintained. Valid values(Unit in seconds) 0 to |
| 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128 |
| **/ |
| UINT8 PsysPowerLimit1Time; |
| |
| /** Offset 0x1BC3 - PL2 Enable Value |
| Enable/Disable Platform Power Limit 2 programming. If this option is disabled, BIOS |
| will program the default values for Platform Power Limit 2. <b>0: Disable</b>; |
| 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 PsysPowerLimit2; |
| |
| /** Offset 0x1BC4 - Enable or Disable MLC Streamer Prefetcher |
| Enable or Disable MLC Streamer Prefetcher; 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 MlcStreamerPrefetcher; |
| |
| /** Offset 0x1BC5 - Enable or Disable MLC Spatial Prefetcher |
| Enable or Disable MLC Spatial Prefetcher; 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 MlcSpatialPrefetcher; |
| |
| /** Offset 0x1BC6 - Enable or Disable Monitor /MWAIT instructions |
| Enable/Disable MonitorMWait, if Disable MonitorMwait, the AP threads Idle Manner |
| should not set in MWAIT Loop. 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 MonitorMwaitEnable; |
| |
| /** Offset 0x1BC7 - Enable or Disable initialization of machine check registers |
| Enable or Disable initialization of machine check registers; 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 MachineCheckEnable; |
| |
| /** Offset 0x1BC8 - AP Idle Manner of waiting for SIPI |
| AP threads Idle Manner for waiting signal to run. 1: HALT loop; <b>2: MWAIT loop</b>; |
| 3: RUN loop. |
| 1: HALT loop, 2: MWAIT loop, 3: RUN loop |
| **/ |
| UINT8 ApIdleManner; |
| |
| /** Offset 0x1BC9 - Control on Processor Trace output scheme |
| Control on Processor Trace output scheme; <b>0: Single Range Output</b>; 1: ToPA Output. |
| 0: Single Range Output, 1: ToPA Output |
| **/ |
| UINT8 ProcessorTraceOutputScheme; |
| |
| /** Offset 0x1BCA - Enable or Disable Processor Trace feature |
| Enable or Disable Processor Trace feature; <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 ProcessorTraceEnable; |
| |
| /** Offset 0x1BCB - Enable or Disable Intel SpeedStep Technology |
| Allows more than two frequency ranges to be supported. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 Eist; |
| |
| /** Offset 0x1BCC - Enable or Disable Energy Efficient P-state |
| Enable/Disable Energy Efficient P-state feature. When set to 0, will disable access |
| to ENERGY_PERFORMANCE_BIAS MSR and CPUID Function will read 0 indicating no support |
| for Energy Efficient policy setting. When set to 1 will enable access to ENERGY_PERFORMANCE_BIAS |
| MSR and CPUID Function will read 1 indicating Energy Efficient policy setting is |
| supported. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 EnergyEfficientPState; |
| |
| /** Offset 0x1BCD - Enable or Disable Energy Efficient Turbo |
| Enable/Disable Energy Efficient Turbo Feature. This feature will opportunistically |
| lower the turbo frequency to increase efficiency. Recommended only to disable in |
| overclocking situations where turbo frequency must remain constant. Otherwise, |
| leave enabled. <b>0: Disable</b>; 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 EnergyEfficientTurbo; |
| |
| /** Offset 0x1BCE - Enable or Disable T states |
| Enable or Disable T states; <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 TStates; |
| |
| /** Offset 0x1BCF - Enable or Disable Bi-Directional PROCHOT# |
| Enable or Disable Bi-Directional PROCHOT#; 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 BiProcHot; |
| |
| /** Offset 0x1BD0 - Enable or Disable PROCHOT# signal being driven externally |
| Enable or Disable PROCHOT# signal being driven externally; 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 DisableProcHotOut; |
| |
| /** Offset 0x1BD1 - Enable or Disable PROCHOT# Response |
| Enable or Disable PROCHOT# Response; <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 ProcHotResponse; |
| |
| /** Offset 0x1BD2 - Enable or Disable VR Thermal Alert |
| Enable or Disable VR Thermal Alert; <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 DisableVrThermalAlert; |
| |
| /** Offset 0x1BD3 - Enable or Disable Thermal Reporting |
| Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 EnableAllThermalFunctions; |
| |
| /** Offset 0x1BD4 - Enable or Disable Thermal Monitor |
| Enable or Disable Thermal Monitor; 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 ThermalMonitor; |
| |
| /** Offset 0x1BD5 - Enable or Disable CPU power states (C-states) |
| Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not |
| 100% utilized. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 Cx; |
| |
| /** Offset 0x1BD6 - Configure C-State Configuration Lock |
| Configure MSR to CFG Lock bit. 0: Disable; <b>1: Enable</b>. |
| $EN_DIS |
| **/ |
| UINT8 PmgCstCfgCtrlLock; |
| |
| /** Offset 0x1BD7 - Enable or Disable Enhanced C-states |
| Enable/Disable C1E. When enabled, CPU will switch to minimum speed when all cores |
| enter C-State. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 C1e; |
| |
| /** Offset 0x1BD8 - Enable or Disable Package Cstate Demotion |
| Enable or Disable Package C-State Demotion. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 PkgCStateDemotion; |
| |
| /** Offset 0x1BD9 - Enable or Disable Package Cstate UnDemotion |
| Enable or Disable Package C-State Un-Demotion. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 PkgCStateUnDemotion; |
| |
| /** Offset 0x1BDA - Enable or Disable CState-Pre wake |
| Disable - to disable the Cstate Pre-Wake. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 CStatePreWake; |
| |
| /** Offset 0x1BDB - Enable or Disable TimedMwait Support. |
| Enable or Disable TimedMwait Support. <b>0: Disable</b>; 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 TimedMwait; |
| |
| /** Offset 0x1BDC - Enable or Disable IO to MWAIT redirection |
| When set, will map IO_read instructions sent to IO registers PMG_IO_BASE_ADDRBASE+offset |
| to MWAIT(offset). <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 CstCfgCtrIoMwaitRedirection; |
| |
| /** Offset 0x1BDD - Set the Max Pkg Cstate |
| Maximum Package C State Limit Setting. Cpu Default: Leaves to Factory default value. |
| Auto: Initializes to deepest available Package C State Limit. Valid values 0 - |
| C0/C1, 1 - C2, 2 - C3, 3 - C6, 4 - C7, 5 - C7S, 6 - C8, 7 - C9, 8 - C10, 254 - |
| CPU Default, <b>255 - Auto</b> |
| **/ |
| UINT8 PkgCStateLimit; |
| |
| /** Offset 0x1BDE - Interrupt Redirection Mode Select |
| Interrupt Redirection Mode Select for Logical Interrupts. 0: Fixed priority; 1: |
| Round robin; 2: Hash vector; 7: No change. |
| **/ |
| UINT8 PpmIrmSetting; |
| |
| /** Offset 0x1BDF - Lock prochot configuration |
| Lock prochot configuration Enable/Disable; 0: Disable;<b> 1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 ProcHotLock; |
| |
| /** Offset 0x1BE0 - Configuration for boot TDP selection |
| cTDP(Assured Power) Mode as Nominal/Level1/Level2/Deactivate TDP(Base Power) selection. |
| Deactivate option will set MSR to Nominal and MMIO to Zero. <b>0: TDP(Base Power) |
| Nominal</b>; 1: TDP(Base Power) Down; 2: TDP(Base Power) Up;0xFF : Deactivate |
| **/ |
| UINT8 ConfigTdpLevel; |
| |
| /** Offset 0x1BE1 - Max P-State Ratio |
| Maximum P-state ratio to use in the custom P-state table. Valid Range 0 to 0x7F |
| **/ |
| UINT8 MaxRatio; |
| |
| /** Offset 0x1BE2 - P-state ratios for custom P-state table |
| P-state ratios for custom P-state table. NumberOfEntries has valid range between |
| 0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries] |
| are configurable. Valid Range of each entry is 0 to 0x7F |
| **/ |
| UINT8 StateRatio[40]; |
| |
| /** Offset 0x1C0A - P-state ratios for max 16 version of custom P-state table |
| P-state ratios for max 16 version of custom P-state table. This table is used for |
| OS versions limited to a max of 16 P-States. If the first entry of this table is |
| 0, or if Number of Entries is 16 or less, then this table will be ignored, and |
| up to the top 16 values of the StateRatio table will be used instead. Valid Range |
| of each entry is 0 to 0x7F |
| **/ |
| UINT8 StateRatioMax16[16]; |
| |
| /** Offset 0x1C1A - Reserved |
| **/ |
| UINT8 Reserved61[2]; |
| |
| /** Offset 0x1C1C - Package Long duration turbo mode power limit |
| Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between |
| Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit |
| and Processor Base Power (TDP) Limit. If value is 0, BIOS will program Processor |
| Base Power (TDP) value. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. Valid |
| Range 0 to 32767. |
| **/ |
| UINT32 PowerLimit1; |
| |
| /** Offset 0x1C20 - Package Short duration turbo mode power limit |
| Power Limit 2 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. If the value is 0, BIOS will program this value as 1.25*Processor |
| Base Power (TDP). Processor applies control policies such that the package power |
| does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 PowerLimit2Power; |
| |
| /** Offset 0x1C24 - Package PL3 power limit |
| Power Limit 3 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. XE SKU: Any value can be programmed. Overclocking SKU: Value |
| must be between Max and Min Power Limits. Other SKUs: This value must be between |
| Min Power Limit and Processor Base Power (TDP) Limit. If the value is 0, BIOS leaves |
| the hardware default value. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 PowerLimit3; |
| |
| /** Offset 0x1C28 - Package PL4 power limit |
| Power Limit 4 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. If the value is 0, BIOS leaves default value. Units are based |
| on POWER_MGMT_CONFIG.CustomPowerUnit. Valid Range 0 to 32767. |
| **/ |
| UINT32 PowerLimit4; |
| |
| /** Offset 0x1C2C - Reserved |
| **/ |
| UINT8 Reserved62[4]; |
| |
| /** Offset 0x1C30 - Tcc Offset Time Window for RATL |
| **/ |
| UINT32 TccOffsetTimeWindowForRatl; |
| |
| /** Offset 0x1C34 - Short term Power Limit value for custom cTDP level 1 |
| Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between |
| Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit |
| and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom1PowerLimit1; |
| |
| /** Offset 0x1C38 - Long term Power Limit value for custom cTDP level 1 |
| Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Processor applies control policies |
| such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom1PowerLimit2; |
| |
| /** Offset 0x1C3C - Short term Power Limit value for custom cTDP level 2 |
| Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between |
| Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit |
| and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom2PowerLimit1; |
| |
| /** Offset 0x1C40 - Long term Power Limit value for custom cTDP level 2 |
| Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Processor applies control policies |
| such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom2PowerLimit2; |
| |
| /** Offset 0x1C44 - Short term Power Limit value for custom cTDP level 3 |
| Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between |
| Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit |
| and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom3PowerLimit1; |
| |
| /** Offset 0x1C48 - Long term Power Limit value for custom cTDP level 3 |
| Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming. |
| Value set 120 = 15W. 0 = no custom override. Processor applies control policies |
| such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 Custom3PowerLimit2; |
| |
| /** Offset 0x1C4C - Platform PL1 power |
| Platform Power Limit 1 Power in Milli Watts. BIOS will round to the nearest 1/8W |
| when programming. Value set 120 = 15W. Any value can be programmed between Max |
| and Min Power Limits. This setting will act as the new PL1 value for the Package |
| RAPL algorithm. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. Valid Range |
| 0 to 32767. |
| **/ |
| UINT32 PsysPowerLimit1Power; |
| |
| /** Offset 0x1C50 - Platform PL2 power |
| Platform Power Limit 2 Power in Milli Watts. BIOS will round to the nearest 1/8W |
| when programming. Value set 120 = 15W. Any value can be programmed between Max |
| and Min Power Limits. This setting will act as the new Max Turbo Power (PL2) value |
| for the Package RAPL algorithm. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. |
| Valid Range 0 to 32767. |
| **/ |
| UINT32 PsysPowerLimit2Power; |
| |
| /** Offset 0x1C54 - Reserved |
| **/ |
| UINT8 Reserved63; |
| |
| /** Offset 0x1C55 - Race To Halt |
| Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency |
| in order to enter pkg C-State faster to reduce overall power. 0: Disable; <b>1: |
| Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 RaceToHalt; |
| |
| /** Offset 0x1C56 - Reserved |
| **/ |
| UINT8 Reserved64; |
| |
| /** Offset 0x1C57 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT |
| Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 HwpInterruptControl; |
| |
| /** Offset 0x1C58 - Reserved |
| **/ |
| UINT8 Reserved65[4]; |
| |
| /** Offset 0x1C5C - Enable or Disable C1 Cstate Demotion |
| Enable or Disable C1 Cstate Auto Demotion. Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 C1StateAutoDemotion; |
| |
| /** Offset 0x1C5D - Enable or Disable C1 Cstate UnDemotion |
| Enable or Disable C1 Cstate Un-Demotion. Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 C1StateUnDemotion; |
| |
| /** Offset 0x1C5E - Minimum Ring ratio limit override |
| Minimum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo |
| ratio limit |
| **/ |
| UINT8 MinRingRatioLimit; |
| |
| /** Offset 0x1C5F - Maximum Ring ratio limit override |
| Maximum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo |
| ratio limit |
| **/ |
| UINT8 MaxRingRatioLimit; |
| |
| /** Offset 0x1C60 - Enable or Disable Per Core P State OS control |
| Enable/Disable Per Core P state OS control mode. When set, the highest core request |
| is used for all other core requests. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 EnablePerCorePState; |
| |
| /** Offset 0x1C61 - Enable or Disable HwP Autonomous Per Core P State OS control |
| Disable Autonomous PCPS Autonomous will request the same value for all cores all |
| the time. 0: Disable; <b>1: Enable</b> |
| $EN_DIS |
| **/ |
| UINT8 EnableHwpAutoPerCorePstate; |
| |
| /** Offset 0x1C62 - Enable or Disable HwP Autonomous EPP Grouping |
| Enable EPP grouping Autonomous will request the same values for all cores with same |
| EPP. Disable EPP grouping autonomous will not necessarily request same values for |
| all cores with same EPP. <b> 0: Disable </b>; 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 EnableHwpAutoEppGrouping; |
| |
| /** Offset 0x1C63 - Enable Configurable TDP |
| Applies cTDP(Assured Power) initialization settings based on non-cTDP(Assured Power) |
| or cTDP(Assured Power). Default is 1: Applies to cTDP(Assured Power); if 0 then |
| applies non-cTDP(Assured Power) and BIOS will bypass cTDP(Assured Power) initialzation flow |
| $EN_DIS |
| **/ |
| UINT8 ApplyConfigTdp; |
| |
| /** Offset 0x1C64 - Reserved |
| **/ |
| UINT8 Reserved66; |
| |
| /** Offset 0x1C65 - Dual Tau Boost |
| Enable Dual Tau Boost feature. This is only applicable for Desktop 35W/65W/125W |
| sku. When DPTF is enabled this feature is ignored. <b>0: Disable</b>; 1: Enable |
| $EN_DIS |
| **/ |
| UINT8 DualTauBoost; |
| |
| /** Offset 0x1C66 - Reserved |
| **/ |
| UINT8 Reserved67[34]; |
| |
| /** Offset 0x1C88 - End of Post message |
| Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1): |
| EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE |
| 0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved |
| **/ |
| UINT8 EndOfPostMessage; |
| |
| /** Offset 0x1C89 - D0I3 Setting for HECI Disable |
| Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all |
| HECI devices |
| $EN_DIS |
| **/ |
| UINT8 DisableD0I3SettingForHeci; |
| |
| /** Offset 0x1C8A - Mctp Broadcast Cycle |
| Test, Determine if MCTP Broadcast is enabled <b>0: Disable</b>; 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 MctpBroadcastCycle; |
| |
| /** Offset 0x1C8B - ME Unconfig on RTC clear |
| 0: Disable ME Unconfig On Rtc Clear. <b>1: Enable ME Unconfig On Rtc Clear</b>. |
| 2: Cmos is clear, status unkonwn. 3: Reserved |
| 0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos |
| is clear, 3: Reserved |
| **/ |
| UINT8 MeUnconfigOnRtcClear; |
| |
| /** Offset 0x1C8C - Enforce Enhanced Debug Mode |
| Determine if ME should enter Enhanced Debug Mode. <b>0: disable</b>, 1: enable |
| $EN_DIS |
| **/ |
| UINT8 EnforceEDebugMode; |
| |
| /** Offset 0x1C8D - Reserved |
| **/ |
| UINT8 Reserved68[17]; |
| |
| /** Offset 0x1C9E - Enable LOCKDOWN SMI |
| Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit. |
| $EN_DIS |
| **/ |
| UINT8 PchLockDownGlobalSmi; |
| |
| /** Offset 0x1C9F - Enable LOCKDOWN BIOS Interface |
| Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register. |
| $EN_DIS |
| **/ |
| UINT8 PchLockDownBiosInterface; |
| |
| /** Offset 0x1CA0 - Unlock all GPIO pads |
| Force all GPIO pads to be unlocked for debug purpose. |
| $EN_DIS |
| **/ |
| UINT8 PchUnlockGpioPads; |
| |
| /** Offset 0x1CA1 - PCH Unlock SideBand access |
| The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before |
| 3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access. |
| $EN_DIS |
| **/ |
| UINT8 PchSbAccessUnlock; |
| |
| /** Offset 0x1CA2 - Reserved |
| **/ |
| UINT8 Reserved69[2]; |
| |
| /** Offset 0x1CA4 - PCIE RP Ltr Max Snoop Latency |
| Latency Tolerance Reporting, Max Snoop Latency. |
| **/ |
| UINT16 PcieRpLtrMaxSnoopLatency[29]; |
| |
| /** Offset 0x1CDE - PCIE RP Ltr Max No Snoop Latency |
| Latency Tolerance Reporting, Max Non-Snoop Latency. |
| **/ |
| UINT16 PcieRpLtrMaxNoSnoopLatency[29]; |
| |
| /** Offset 0x1D18 - PCIE RP Snoop Latency Override Mode |
| Latency Tolerance Reporting, Snoop Latency Override Mode. |
| **/ |
| UINT8 PcieRpSnoopLatencyOverrideMode[29]; |
| |
| /** Offset 0x1D35 - PCIE RP Snoop Latency Override Multiplier |
| Latency Tolerance Reporting, Snoop Latency Override Multiplier. |
| **/ |
| UINT8 PcieRpSnoopLatencyOverrideMultiplier[29]; |
| |
| /** Offset 0x1D52 - PCIE RP Snoop Latency Override Value |
| Latency Tolerance Reporting, Snoop Latency Override Value. |
| **/ |
| UINT16 PcieRpSnoopLatencyOverrideValue[29]; |
| |
| /** Offset 0x1D8C - PCIE RP Non Snoop Latency Override Mode |
| Latency Tolerance Reporting, Non-Snoop Latency Override Mode. |
| **/ |
| UINT8 PcieRpNonSnoopLatencyOverrideMode[29]; |
| |
| /** Offset 0x1DA9 - PCIE RP Non Snoop Latency Override Multiplier |
| Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. |
| **/ |
| UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[29]; |
| |
| /** Offset 0x1DC6 - PCIE RP Non Snoop Latency Override Value |
| Latency Tolerance Reporting, Non-Snoop Latency Override Value. |
| **/ |
| UINT16 PcieRpNonSnoopLatencyOverrideValue[29]; |
| |
| /** Offset 0x1E00 - PCIE RP Slot Power Limit Scale |
| Specifies scale used for slot power limit value. Leave as 0 to set to default. |
| **/ |
| UINT8 PcieRpSlotPowerLimitScale[29]; |
| |
| /** Offset 0x1E1D - Reserved |
| **/ |
| UINT8 Reserved70; |
| |
| /** Offset 0x1E1E - PCIE RP Slot Power Limit Value |
| Specifies upper limit on power supplie by slot. Leave as 0 to set to default. |
| **/ |
| UINT16 PcieRpSlotPowerLimitValue[29]; |
| |
| /** Offset 0x1E58 - PCIE RP Enable Port8xh Decode |
| This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable; |
| 1: Enable. |
| $EN_DIS |
| **/ |
| UINT8 PcieEnablePort8xhDecode; |
| |
| /** Offset 0x1E59 - PCIE Port8xh Decode Port Index |
| The Index of PCIe Port that is selected for Port8xh Decode (0 Based). |
| **/ |
| UINT8 PchPciePort8xhDecodePortIndex; |
| |
| /** Offset 0x1E5A - PCH Energy Reporting |
| Disable/Enable PCH to CPU energy report feature. |
| $EN_DIS |
| **/ |
| UINT8 PchPmDisableEnergyReport; |
| |
| /** Offset 0x1E5B - PCH Sata Test Mode |
| Allow entrance to the PCH SATA test modes. |
| $EN_DIS |
| **/ |
| UINT8 SataTestMode; |
| |
| /** Offset 0x1E5C - PCH USB OverCurrent mapping lock enable |
| If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning |
| that OC mapping data will be consumed by xHCI and OC mapping registers will be locked. |
| $EN_DIS |
| **/ |
| UINT8 PchXhciOcLock; |
| |
| /** Offset 0x1E5D - Low Power Mode Enable/Disable config mask |
| Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds |
| to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0, |
| LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4. |
| **/ |
| UINT8 PmcLpmS0ixSubStateEnableMask; |
| |
| /** Offset 0x1E5E - Reserved |
| **/ |
| UINT8 Reserved71[105]; |
| |
| /** Offset 0x1EC7 - PMC C10 dynamic threshold dajustment enable |
| Set if you want to enable PMC C10 dynamic threshold adjustment. Only works on supported SKUs |
| $EN_DIS |
| **/ |
| UINT8 PmcC10DynamicThresholdAdjustment; |
| |
| /** Offset 0x1EC8 - Reserved |
| **/ |
| UINT8 Reserved72[36]; |
| |
| /** Offset 0x1EEC - FspEventHandler |
| <b>Optional</b> pointer to the boot loader's implementation of FSP_EVENT_HANDLER. |
| **/ |
| UINT32 FspEventHandler; |
| |
| /** Offset 0x1EF0 - Reserved |
| **/ |
| UINT8 Reserved73[32]; |
| } FSP_S_CONFIG; |
| |
| /** Fsp S UPD Configuration |
| **/ |
| typedef struct { |
| |
| /** Offset 0x0000 |
| **/ |
| FSP_UPD_HEADER FspUpdHeader; |
| |
| /** Offset 0x0020 |
| **/ |
| FSPS_ARCH_UPD FspsArchUpd; |
| |
| /** Offset 0x0040 |
| **/ |
| FSP_S_CONFIG FspsConfig; |
| |
| /** Offset 0x1F10 |
| **/ |
| UINT8 Rsvd600[6]; |
| |
| /** Offset 0x1F16 |
| **/ |
| UINT16 UpdTerminator; |
| } FSPS_UPD; |
| |
| #pragma pack() |
| |
| #endif |