| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <assert.h> |
| #include <commonlib/helpers.h> |
| #include <console/console.h> |
| #include <string.h> |
| #include <arch/cpu.h> |
| #include <device/mmio.h> |
| #include <device/pci_ops.h> |
| #include <northbridge/intel/sandybridge/chip.h> |
| #include <device/pci_def.h> |
| #include <delay.h> |
| #include <types.h> |
| |
| #include "raminit_native.h" |
| #include "raminit_common.h" |
| #include "raminit_tables.h" |
| #include "sandybridge.h" |
| |
| /* FIXME: no support for 3-channel chipsets */ |
| |
| static void sfence(void) |
| { |
| asm volatile ("sfence"); |
| } |
| |
| /* Toggle IO reset bit */ |
| static void toggle_io_reset(void) |
| { |
| u32 r32 = MCHBAR32(MC_INIT_STATE_G); |
| MCHBAR32(MC_INIT_STATE_G) = r32 | (1 << 5); |
| udelay(1); |
| MCHBAR32(MC_INIT_STATE_G) = r32 & ~(1 << 5); |
| udelay(1); |
| } |
| |
| static u32 get_XOVER_CLK(u8 rankmap) |
| { |
| return rankmap << 24; |
| } |
| |
| static u32 get_XOVER_CMD(u8 rankmap) |
| { |
| u32 reg; |
| |
| /* Enable xover cmd */ |
| reg = 0x4000; |
| |
| /* Enable xover ctl */ |
| if (rankmap & 0x03) |
| reg |= (1 << 17); |
| |
| if (rankmap & 0x0c) |
| reg |= (1 << 26); |
| |
| return reg; |
| } |
| |
| void dram_find_common_params(ramctr_timing *ctrl) |
| { |
| size_t valid_dimms; |
| int channel, slot; |
| dimm_info *dimms = &ctrl->info; |
| |
| ctrl->cas_supported = (1 << (MAX_CAS - MIN_CAS + 1)) - 1; |
| valid_dimms = 0; |
| |
| FOR_ALL_CHANNELS for (slot = 0; slot < 2; slot++) { |
| |
| const dimm_attr *dimm = &dimms->dimm[channel][slot]; |
| if (dimm->dram_type != SPD_MEMORY_TYPE_SDRAM_DDR3) |
| continue; |
| |
| valid_dimms++; |
| |
| /* Find all possible CAS combinations */ |
| ctrl->cas_supported &= dimm->cas_supported; |
| |
| /* Find the smallest common latencies supported by all DIMMs */ |
| ctrl->tCK = MAX(ctrl->tCK, dimm->tCK); |
| ctrl->tAA = MAX(ctrl->tAA, dimm->tAA); |
| ctrl->tWR = MAX(ctrl->tWR, dimm->tWR); |
| ctrl->tRCD = MAX(ctrl->tRCD, dimm->tRCD); |
| ctrl->tRRD = MAX(ctrl->tRRD, dimm->tRRD); |
| ctrl->tRP = MAX(ctrl->tRP, dimm->tRP); |
| ctrl->tRAS = MAX(ctrl->tRAS, dimm->tRAS); |
| ctrl->tRFC = MAX(ctrl->tRFC, dimm->tRFC); |
| ctrl->tWTR = MAX(ctrl->tWTR, dimm->tWTR); |
| ctrl->tRTP = MAX(ctrl->tRTP, dimm->tRTP); |
| ctrl->tFAW = MAX(ctrl->tFAW, dimm->tFAW); |
| ctrl->tCWL = MAX(ctrl->tCWL, dimm->tCWL); |
| ctrl->tCMD = MAX(ctrl->tCMD, dimm->tCMD); |
| } |
| |
| if (!ctrl->cas_supported) |
| die("Unsupported DIMM combination. DIMMS do not support common CAS latency"); |
| |
| if (!valid_dimms) |
| die("No valid DIMMs found"); |
| } |
| |
| void dram_xover(ramctr_timing *ctrl) |
| { |
| u32 reg; |
| int channel; |
| |
| FOR_ALL_CHANNELS { |
| /* Enable xover clk */ |
| reg = get_XOVER_CLK(ctrl->rankmap[channel]); |
| printram("XOVER CLK [%x] = %x\n", GDCRCKPICODE_ch(channel), reg); |
| MCHBAR32(GDCRCKPICODE_ch(channel)) = reg; |
| |
| /* Enable xover ctl & xover cmd */ |
| reg = get_XOVER_CMD(ctrl->rankmap[channel]); |
| printram("XOVER CMD [%x] = %x\n", GDCRCMDPICODING_ch(channel), reg); |
| MCHBAR32(GDCRCMDPICODING_ch(channel)) = reg; |
| } |
| } |
| |
| static void dram_odt_stretch(ramctr_timing *ctrl, int channel) |
| { |
| u32 addr, stretch; |
| |
| stretch = ctrl->ref_card_offset[channel]; |
| /* |
| * ODT stretch: |
| * Delay ODT signal by stretch value. Useful for multi DIMM setups on the same channel. |
| */ |
| if (IS_SANDY_CPU(ctrl->cpu) && IS_SANDY_CPU_C(ctrl->cpu)) { |
| if (stretch == 2) |
| stretch = 3; |
| |
| addr = SCHED_SECOND_CBIT_ch(channel); |
| MCHBAR32_AND_OR(addr, ~(0xf << 10), (stretch << 12) | (stretch << 10)); |
| printk(RAM_DEBUG, "OTHP Workaround [%x] = %x\n", addr, MCHBAR32(addr)); |
| } else { |
| addr = TC_OTHP_ch(channel); |
| union tc_othp_reg tc_othp = { |
| .raw = MCHBAR32(addr), |
| }; |
| tc_othp.odt_delay_d0 = stretch; |
| tc_othp.odt_delay_d1 = stretch; |
| MCHBAR32(addr) = tc_othp.raw; |
| printk(RAM_DEBUG, "OTHP [%x] = %x\n", addr, MCHBAR32(addr)); |
| } |
| } |
| |
| void dram_timing_regs(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| /* BIN parameters */ |
| const union tc_dbp_reg tc_dbp = { |
| .tRCD = ctrl->tRCD, |
| .tRP = ctrl->tRP, |
| .tAA = ctrl->CAS, |
| .tCWL = ctrl->CWL, |
| .tRAS = ctrl->tRAS, |
| }; |
| |
| /* Regular access parameters */ |
| const union tc_rap_reg tc_rap = { |
| .tRRD = ctrl->tRRD, |
| .tRTP = ctrl->tRTP, |
| .tCKE = ctrl->tCKE, |
| .tWTR = ctrl->tWTR, |
| .tFAW = ctrl->tFAW, |
| .tWR = ctrl->tWR, |
| .tCMD = 3, |
| }; |
| |
| /* Other parameters */ |
| const union tc_othp_reg tc_othp = { |
| .tXPDLL = ctrl->tXPDLL, |
| .tXP = ctrl->tXP, |
| .tAONPD = ctrl->tAONPD, |
| .tCPDED = 2, |
| .tPRPDEN = 1, |
| }; |
| |
| /* |
| * If tXP and tXPDLL are very high, we need to increase them by one. |
| * This can only happen on Ivy Bridge, and when overclocking the RAM. |
| */ |
| const union tc_dtp_reg tc_dtp = { |
| .overclock_tXP = ctrl->tXP >= 8, |
| .overclock_tXPDLL = ctrl->tXPDLL >= 32, |
| }; |
| |
| /* |
| * TC-Refresh timing parameters: |
| * The tREFIx9 field should be programmed to minimum of 8.9 * tREFI (to allow |
| * for possible delays from ZQ or isoc) and tRASmax (70us) divided by 1024. |
| */ |
| const u32 val32 = MIN((ctrl->tREFI * 89) / 10, (70000 << 8) / ctrl->tCK); |
| |
| const union tc_rftp_reg tc_rftp = { |
| .tREFI = ctrl->tREFI, |
| .tRFC = ctrl->tRFC, |
| .tREFIx9 = val32 / 1024, |
| }; |
| |
| /* Self-refresh timing parameters */ |
| const union tc_srftp_reg tc_srftp = { |
| .tXSDLL = tDLLK, |
| .tXS_offset = ctrl->tXSOffset, |
| .tZQOPER = tDLLK - ctrl->tXSOffset, |
| .tMOD = ctrl->tMOD - 8, |
| }; |
| |
| FOR_ALL_CHANNELS { |
| printram("DBP [%x] = %x\n", TC_DBP_ch(channel), tc_dbp.raw); |
| MCHBAR32(TC_DBP_ch(channel)) = tc_dbp.raw; |
| |
| printram("RAP [%x] = %x\n", TC_RAP_ch(channel), tc_rap.raw); |
| MCHBAR32(TC_RAP_ch(channel)) = tc_rap.raw; |
| |
| printram("OTHP [%x] = %x\n", TC_OTHP_ch(channel), tc_othp.raw); |
| MCHBAR32(TC_OTHP_ch(channel)) = tc_othp.raw; |
| |
| if (IS_IVY_CPU(ctrl->cpu)) { |
| /* Debug parameters - only applies to Ivy Bridge */ |
| MCHBAR32(TC_DTP_ch(channel)) = tc_dtp.raw; |
| } |
| |
| dram_odt_stretch(ctrl, channel); |
| |
| printram("REFI [%x] = %x\n", TC_RFTP_ch(channel), tc_rftp.raw); |
| MCHBAR32(TC_RFTP_ch(channel)) = tc_rftp.raw; |
| |
| union tc_rfp_reg tc_rfp = { |
| .raw = MCHBAR32(TC_RFP_ch(channel)), |
| }; |
| tc_rfp.oref_ri = 0xff; |
| MCHBAR32(TC_RFP_ch(channel)) = tc_rfp.raw; |
| |
| printram("SRFTP [%x] = %x\n", TC_SRFTP_ch(channel), tc_srftp.raw); |
| MCHBAR32(TC_SRFTP_ch(channel)) = tc_srftp.raw; |
| } |
| } |
| |
| void dram_dimm_mapping(ramctr_timing *ctrl) |
| { |
| int channel; |
| dimm_info *info = &ctrl->info; |
| |
| FOR_ALL_CHANNELS { |
| dimm_attr *dimmA, *dimmB; |
| u32 reg = 0; |
| |
| if (info->dimm[channel][0].size_mb >= info->dimm[channel][1].size_mb) { |
| dimmA = &info->dimm[channel][0]; |
| dimmB = &info->dimm[channel][1]; |
| reg |= (0 << 16); |
| } else { |
| dimmA = &info->dimm[channel][1]; |
| dimmB = &info->dimm[channel][0]; |
| reg |= (1 << 16); |
| } |
| |
| if (dimmA && (dimmA->ranks > 0)) { |
| reg |= (dimmA->size_mb / 256) << 0; |
| reg |= (dimmA->ranks - 1) << 17; |
| reg |= (dimmA->width / 8 - 1) << 19; |
| } |
| |
| if (dimmB && (dimmB->ranks > 0)) { |
| reg |= (dimmB->size_mb / 256) << 8; |
| reg |= (dimmB->ranks - 1) << 18; |
| reg |= (dimmB->width / 8 - 1) << 20; |
| } |
| |
| /* |
| * Rank interleave: Bit 16 of the physical address space sets |
| * the rank to use in a dual single rank DIMM configuration. |
| * That results in every 64KiB being interleaved between two ranks. |
| */ |
| reg |= 1 << 21; |
| /* Enhanced interleave */ |
| reg |= 1 << 22; |
| |
| if ((dimmA && (dimmA->ranks > 0)) || (dimmB && (dimmB->ranks > 0))) { |
| ctrl->mad_dimm[channel] = reg; |
| } else { |
| ctrl->mad_dimm[channel] = 0; |
| } |
| } |
| } |
| |
| void dram_dimm_set_mapping(ramctr_timing *ctrl, int training) |
| { |
| int channel; |
| u32 ecc; |
| |
| if (ctrl->ecc_enabled) |
| ecc = training ? (1 << 24) : (3 << 24); |
| else |
| ecc = 0; |
| |
| FOR_ALL_CHANNELS { |
| MCHBAR32(MAD_DIMM(channel)) = ctrl->mad_dimm[channel] | ecc; |
| } |
| |
| if (ctrl->ecc_enabled) |
| udelay(10); |
| } |
| |
| void dram_zones(ramctr_timing *ctrl, int training) |
| { |
| u32 reg, ch0size, ch1size; |
| u8 val; |
| reg = 0; |
| val = 0; |
| |
| if (training) { |
| ch0size = ctrl->channel_size_mb[0] ? 256 : 0; |
| ch1size = ctrl->channel_size_mb[1] ? 256 : 0; |
| } else { |
| ch0size = ctrl->channel_size_mb[0]; |
| ch1size = ctrl->channel_size_mb[1]; |
| } |
| |
| if (ch0size >= ch1size) { |
| reg = MCHBAR32(MAD_ZR); |
| val = ch1size / 256; |
| reg = (reg & ~0xff000000) | val << 24; |
| reg = (reg & ~0x00ff0000) | (2 * val) << 16; |
| MCHBAR32(MAD_ZR) = reg; |
| MCHBAR32(MAD_CHNL) = 0x24; |
| |
| } else { |
| reg = MCHBAR32(MAD_ZR); |
| val = ch0size / 256; |
| reg = (reg & ~0xff000000) | val << 24; |
| reg = (reg & ~0x00ff0000) | (2 * val) << 16; |
| MCHBAR32(MAD_ZR) = reg; |
| MCHBAR32(MAD_CHNL) = 0x21; |
| } |
| } |
| |
| #define DEFAULT_PCI_MMIO_SIZE 2048 |
| |
| static unsigned int get_mmio_size(void) |
| { |
| const struct device *dev; |
| const struct northbridge_intel_sandybridge_config *cfg = NULL; |
| |
| dev = pcidev_path_on_root(PCI_DEVFN(0, 0)); |
| if (dev) |
| cfg = dev->chip_info; |
| |
| /* If this is zero, it just means devicetree.cb didn't set it */ |
| if (!cfg || cfg->pci_mmio_size == 0) |
| return DEFAULT_PCI_MMIO_SIZE; |
| else |
| return cfg->pci_mmio_size; |
| } |
| |
| /* |
| * Returns the ECC mode the NB is running at. It takes precedence over ECC capability. |
| * The ME/PCU/.. has the ability to change this. |
| * Return 0: ECC is optional |
| * Return 1: ECC is forced |
| */ |
| bool get_host_ecc_forced(void) |
| { |
| /* read Capabilities A Register */ |
| const u32 reg32 = pci_read_config32(HOST_BRIDGE, CAPID0_A); |
| return !!(reg32 & (1 << 24)); |
| } |
| |
| /* |
| * Returns the ECC capability. |
| * The ME/PCU/.. has the ability to change this. |
| * Return 0: ECC is disabled |
| * Return 1: ECC is possible |
| */ |
| bool get_host_ecc_cap(void) |
| { |
| /* read Capabilities A Register */ |
| const u32 reg32 = pci_read_config32(HOST_BRIDGE, CAPID0_A); |
| return !(reg32 & (1 << 25)); |
| } |
| |
| void dram_memorymap(ramctr_timing *ctrl, int me_uma_size) |
| { |
| u32 reg, val, reclaim, tom, gfxstolen, gttsize; |
| size_t tsegbase, toludbase, remapbase, gfxstolenbase, mmiosize, gttbase; |
| size_t tsegsize, touudbase, remaplimit, mestolenbase, tsegbasedelta; |
| uint16_t ggc; |
| |
| mmiosize = get_mmio_size(); |
| |
| ggc = pci_read_config16(HOST_BRIDGE, GGC); |
| if (!(ggc & 2)) { |
| gfxstolen = ((ggc >> 3) & 0x1f) * 32; |
| gttsize = ((ggc >> 8) & 0x3); |
| } else { |
| gfxstolen = 0; |
| gttsize = 0; |
| } |
| |
| tsegsize = CONFIG_SMM_TSEG_SIZE >> 20; |
| |
| tom = ctrl->channel_size_mb[0] + ctrl->channel_size_mb[1]; |
| |
| mestolenbase = tom - me_uma_size; |
| |
| toludbase = MIN(4096 - mmiosize + gfxstolen + gttsize + tsegsize, tom - me_uma_size); |
| |
| gfxstolenbase = toludbase - gfxstolen; |
| gttbase = gfxstolenbase - gttsize; |
| |
| tsegbase = gttbase - tsegsize; |
| |
| /* Round tsegbase down to nearest address aligned to tsegsize */ |
| tsegbasedelta = tsegbase & (tsegsize - 1); |
| tsegbase &= ~(tsegsize - 1); |
| |
| gttbase -= tsegbasedelta; |
| gfxstolenbase -= tsegbasedelta; |
| toludbase -= tsegbasedelta; |
| |
| /* Test if it is possible to reclaim a hole in the RAM addressing */ |
| if (tom - me_uma_size > toludbase) { |
| /* Reclaim is possible */ |
| reclaim = 1; |
| remapbase = MAX(4096, tom - me_uma_size); |
| remaplimit = remapbase + MIN(4096, tom - me_uma_size) - toludbase - 1; |
| touudbase = remaplimit + 1; |
| } else { |
| // Reclaim not possible |
| reclaim = 0; |
| touudbase = tom - me_uma_size; |
| } |
| |
| /* Update memory map in PCIe configuration space */ |
| printk(BIOS_DEBUG, "Update PCI-E configuration space:\n"); |
| |
| /* TOM (top of memory) */ |
| reg = pci_read_config32(HOST_BRIDGE, TOM); |
| val = tom & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TOM, reg); |
| pci_write_config32(HOST_BRIDGE, TOM, reg); |
| |
| reg = pci_read_config32(HOST_BRIDGE, TOM + 4); |
| val = tom & 0xfffff000; |
| reg = (reg & ~0x000fffff) | (val >> 12); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TOM + 4, reg); |
| pci_write_config32(HOST_BRIDGE, TOM + 4, reg); |
| |
| /* TOLUD (Top Of Low Usable DRAM) */ |
| reg = pci_read_config32(HOST_BRIDGE, TOLUD); |
| val = toludbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TOLUD, reg); |
| pci_write_config32(HOST_BRIDGE, TOLUD, reg); |
| |
| /* TOUUD LSB (Top Of Upper Usable DRAM) */ |
| reg = pci_read_config32(HOST_BRIDGE, TOUUD); |
| val = touudbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TOUUD, reg); |
| pci_write_config32(HOST_BRIDGE, TOUUD, reg); |
| |
| /* TOUUD MSB */ |
| reg = pci_read_config32(HOST_BRIDGE, TOUUD + 4); |
| val = touudbase & 0xfffff000; |
| reg = (reg & ~0x000fffff) | (val >> 12); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TOUUD + 4, reg); |
| pci_write_config32(HOST_BRIDGE, TOUUD + 4, reg); |
| |
| if (reclaim) { |
| /* REMAP BASE */ |
| pci_write_config32(HOST_BRIDGE, REMAPBASE, remapbase << 20); |
| pci_write_config32(HOST_BRIDGE, REMAPBASE + 4, remapbase >> 12); |
| |
| /* REMAP LIMIT */ |
| pci_write_config32(HOST_BRIDGE, REMAPLIMIT, remaplimit << 20); |
| pci_write_config32(HOST_BRIDGE, REMAPLIMIT + 4, remaplimit >> 12); |
| } |
| /* TSEG */ |
| reg = pci_read_config32(HOST_BRIDGE, TSEGMB); |
| val = tsegbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", TSEGMB, reg); |
| pci_write_config32(HOST_BRIDGE, TSEGMB, reg); |
| |
| /* GFX stolen memory */ |
| reg = pci_read_config32(HOST_BRIDGE, BDSM); |
| val = gfxstolenbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", BDSM, reg); |
| pci_write_config32(HOST_BRIDGE, BDSM, reg); |
| |
| /* GTT stolen memory */ |
| reg = pci_read_config32(HOST_BRIDGE, BGSM); |
| val = gttbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", BGSM, reg); |
| pci_write_config32(HOST_BRIDGE, BGSM, reg); |
| |
| if (me_uma_size) { |
| reg = pci_read_config32(HOST_BRIDGE, MESEG_MASK + 4); |
| val = (0x80000 - me_uma_size) & 0xfffff000; |
| reg = (reg & ~0x000fffff) | (val >> 12); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", MESEG_MASK + 4, reg); |
| pci_write_config32(HOST_BRIDGE, MESEG_MASK + 4, reg); |
| |
| /* ME base */ |
| reg = pci_read_config32(HOST_BRIDGE, MESEG_BASE); |
| val = mestolenbase & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", MESEG_BASE, reg); |
| pci_write_config32(HOST_BRIDGE, MESEG_BASE, reg); |
| |
| reg = pci_read_config32(HOST_BRIDGE, MESEG_BASE + 4); |
| val = mestolenbase & 0xfffff000; |
| reg = (reg & ~0x000fffff) | (val >> 12); |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", MESEG_BASE + 4, reg); |
| pci_write_config32(HOST_BRIDGE, MESEG_BASE + 4, reg); |
| |
| /* ME mask */ |
| reg = pci_read_config32(HOST_BRIDGE, MESEG_MASK); |
| val = (0x80000 - me_uma_size) & 0xfff; |
| reg = (reg & ~0xfff00000) | (val << 20); |
| reg = reg | ME_STLEN_EN; /* Set ME memory enable */ |
| reg = reg | MELCK; /* Set lock bit on ME mem */ |
| printk(BIOS_DEBUG, "PCI(0, 0, 0)[%x] = %x\n", MESEG_MASK, reg); |
| pci_write_config32(HOST_BRIDGE, MESEG_MASK, reg); |
| } |
| } |
| |
| static void write_reset(ramctr_timing *ctrl) |
| { |
| int channel, slotrank; |
| |
| /* Choose a populated channel */ |
| channel = (ctrl->rankmap[0]) ? 0 : 1; |
| |
| wait_for_iosav(channel); |
| |
| /* Choose a populated rank */ |
| slotrank = (ctrl->rankmap[channel] & 1) ? 0 : 2; |
| |
| iosav_write_zqcs_sequence(channel, slotrank, 3, 8, 0); |
| |
| /* |
| * Execute command queue - why is bit 22 set here?! |
| * |
| * This is actually using the IOSAV state machine as a timer, so refresh is allowed. |
| */ |
| iosav_run_queue(channel, 1, 1); |
| |
| wait_for_iosav(channel); |
| } |
| |
| void dram_jedecreset(ramctr_timing *ctrl) |
| { |
| u32 reg; |
| int channel; |
| |
| while (!(MCHBAR32(RCOMP_TIMER) & (1 << 16))) |
| ; |
| do { |
| reg = MCHBAR32(IOSAV_STATUS_ch(0)); |
| } while ((reg & 0x14) == 0); |
| |
| /* Set state of memory controller */ |
| reg = 0x112; |
| MCHBAR32(MC_INIT_STATE_G) = reg; |
| MCHBAR32(MC_INIT_STATE) = 0; |
| reg |= 2; /* DDR reset */ |
| MCHBAR32(MC_INIT_STATE_G) = reg; |
| |
| /* Assert DIMM reset signal */ |
| MCHBAR32_AND(MC_INIT_STATE_G, ~(1 << 1)); |
| |
| /* Wait 200us */ |
| udelay(200); |
| |
| /* Deassert DIMM reset signal */ |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 1); |
| |
| /* Wait 500us */ |
| udelay(500); |
| |
| /* Enable DCLK */ |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 2); |
| |
| /* XXX Wait 20ns */ |
| udelay(1); |
| |
| FOR_ALL_CHANNELS { |
| /* Set valid rank CKE */ |
| reg = ctrl->rankmap[channel]; |
| MCHBAR32(MC_INIT_STATE_ch(channel)) = reg; |
| |
| /* Wait 10ns for ranks to settle */ |
| // udelay(0.01); |
| |
| reg = (reg & ~0xf0) | (ctrl->rankmap[channel] << 4); |
| MCHBAR32(MC_INIT_STATE_ch(channel)) = reg; |
| |
| /* Write reset using a NOP */ |
| write_reset(ctrl); |
| } |
| } |
| |
| /* |
| * DDR3 Rank1 Address mirror swap the following pins: |
| * A3<->A4, A5<->A6, A7<->A8, BA0<->BA1 |
| */ |
| static void ddr3_mirror_mrreg(int *bank, u32 *addr) |
| { |
| *bank = ((*bank >> 1) & 1) | ((*bank << 1) & 2); |
| *addr = (*addr & ~0x1f8) | ((*addr >> 1) & 0xa8) | ((*addr & 0xa8) << 1); |
| } |
| |
| static void write_mrreg(ramctr_timing *ctrl, int channel, int slotrank, int reg, u32 val) |
| { |
| wait_for_iosav(channel); |
| |
| if (ctrl->rank_mirror[channel][slotrank]) |
| ddr3_mirror_mrreg(®, &val); |
| |
| const struct iosav_ssq sequence[] = { |
| /* DRAM command MRS */ |
| [0] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_MRS, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = 4, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = val, |
| .rowbits = 6, |
| .bank = reg, |
| .rank = slotrank, |
| }, |
| }, |
| /* DRAM command MRS */ |
| [1] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_MRS, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = 4, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = val, |
| .rowbits = 6, |
| .bank = reg, |
| .rank = slotrank, |
| }, |
| }, |
| /* DRAM command MRS */ |
| [2] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_MRS, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = ctrl->tMOD, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = val, |
| .rowbits = 6, |
| .bank = reg, |
| .rank = slotrank, |
| }, |
| }, |
| }; |
| iosav_write_sequence(channel, sequence, ARRAY_SIZE(sequence)); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| } |
| |
| /* Obtain optimal power down mode for current configuration */ |
| static enum pdwm_mode get_power_down_mode(ramctr_timing *ctrl) |
| { |
| if (ctrl->tXP > 8) |
| return PDM_NONE; |
| |
| if (ctrl->tXPDLL > 32) |
| return PDM_PPD; |
| |
| if (CONFIG(RAMINIT_ALWAYS_ALLOW_DLL_OFF) || get_platform_type() == PLATFORM_MOBILE) |
| return PDM_DLL_OFF; |
| |
| return PDM_APD_PPD; |
| } |
| |
| static u32 make_mr0(ramctr_timing *ctrl, u8 rank) |
| { |
| u16 mr0reg, mch_cas, mch_wr; |
| static const u8 mch_wr_t[12] = { 1, 2, 3, 4, 0, 5, 0, 6, 0, 7, 0, 0 }; |
| |
| const enum pdwm_mode power_down = get_power_down_mode(ctrl); |
| |
| const bool slow_exit = power_down == PDM_DLL_OFF || power_down == PDM_APD_DLL_OFF; |
| |
| /* Convert CAS to MCH register friendly */ |
| if (ctrl->CAS < 12) { |
| mch_cas = (u16) ((ctrl->CAS - 4) << 1); |
| } else { |
| mch_cas = (u16) (ctrl->CAS - 12); |
| mch_cas = ((mch_cas << 1) | 0x1); |
| } |
| |
| /* Convert tWR to MCH register friendly */ |
| mch_wr = mch_wr_t[ctrl->tWR - 5]; |
| |
| /* DLL Reset - self clearing - set after CLK frequency has been changed */ |
| mr0reg = 1 << 8; |
| |
| mr0reg |= (mch_cas & 0x1) << 2; |
| mr0reg |= (mch_cas & 0xe) << 3; |
| mr0reg |= mch_wr << 9; |
| |
| /* Precharge PD - Use slow exit when DLL-off is used - mostly power-saving feature */ |
| mr0reg |= !slow_exit << 12; |
| return mr0reg; |
| } |
| |
| static void dram_mr0(ramctr_timing *ctrl, u8 rank, int channel) |
| { |
| write_mrreg(ctrl, channel, rank, 0, make_mr0(ctrl, rank)); |
| } |
| |
| static odtmap get_ODT(ramctr_timing *ctrl, int channel) |
| { |
| /* Get ODT based on rankmap */ |
| int dimms_per_ch = (ctrl->rankmap[channel] & 1) + ((ctrl->rankmap[channel] >> 2) & 1); |
| |
| if (dimms_per_ch == 1) { |
| return (const odtmap){60, 60}; |
| } else { |
| return (const odtmap){120, 30}; |
| } |
| } |
| |
| static u32 encode_odt(u32 odt) |
| { |
| switch (odt) { |
| case 30: |
| return (1 << 9) | (1 << 2); // RZQ/8, RZQ/4 |
| case 60: |
| return (1 << 2); // RZQ/4 |
| case 120: |
| return (1 << 6); // RZQ/2 |
| default: |
| case 0: |
| return 0; |
| } |
| } |
| |
| static u32 make_mr1(ramctr_timing *ctrl, u8 rank, int channel) |
| { |
| odtmap odt; |
| u32 mr1reg; |
| |
| odt = get_ODT(ctrl, channel); |
| mr1reg = 2; |
| |
| mr1reg |= encode_odt(odt.rttnom); |
| |
| return mr1reg; |
| } |
| |
| static void dram_mr1(ramctr_timing *ctrl, u8 rank, int channel) |
| { |
| u16 mr1reg; |
| |
| mr1reg = make_mr1(ctrl, rank, channel); |
| |
| write_mrreg(ctrl, channel, rank, 1, mr1reg); |
| } |
| |
| static void dram_mr2(ramctr_timing *ctrl, u8 rank, int channel) |
| { |
| const u16 pasr = 0; |
| const u16 cwl = ctrl->CWL - 5; |
| const odtmap odt = get_ODT(ctrl, channel); |
| |
| int srt = 0; |
| if (IS_IVY_CPU(ctrl->cpu) && ctrl->tCK >= TCK_1066MHZ) |
| srt = ctrl->extended_temperature_range && !ctrl->auto_self_refresh; |
| |
| u16 mr2reg = 0; |
| mr2reg |= pasr; |
| mr2reg |= cwl << 3; |
| mr2reg |= ctrl->auto_self_refresh << 6; |
| mr2reg |= srt << 7; |
| mr2reg |= (odt.rttwr / 60) << 9; |
| |
| write_mrreg(ctrl, channel, rank, 2, mr2reg); |
| |
| /* Program MR2 shadow */ |
| u32 reg32 = MCHBAR32(TC_MR2_SHADOW_ch(channel)); |
| |
| reg32 &= 3 << 14 | 3 << 6; |
| |
| reg32 |= mr2reg & ~(3 << 6); |
| |
| if (rank & 1) { |
| if (srt) |
| reg32 |= 1 << (rank / 2 + 6); |
| } else { |
| if (ctrl->rank_mirror[channel][rank]) |
| reg32 |= 1 << (rank / 2 + 14); |
| } |
| MCHBAR32(TC_MR2_SHADOW_ch(channel)) = reg32; |
| } |
| |
| static void dram_mr3(ramctr_timing *ctrl, u8 rank, int channel) |
| { |
| write_mrreg(ctrl, channel, rank, 3, 0); |
| } |
| |
| void dram_mrscommands(ramctr_timing *ctrl) |
| { |
| u8 slotrank; |
| int channel; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| FOR_ALL_POPULATED_RANKS { |
| /* MR2 */ |
| dram_mr2(ctrl, slotrank, channel); |
| |
| /* MR3 */ |
| dram_mr3(ctrl, slotrank, channel); |
| |
| /* MR1 */ |
| dram_mr1(ctrl, slotrank, channel); |
| |
| /* MR0 */ |
| dram_mr0(ctrl, slotrank, channel); |
| } |
| } |
| |
| const struct iosav_ssq zqcl_sequence[] = { |
| /* DRAM command NOP (without ODT nor chip selects) */ |
| [0] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_NOP & ~(0xff << 8), |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = 15, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = 2, |
| .rowbits = 6, |
| .bank = 0, |
| .rank = 0, |
| }, |
| }, |
| /* DRAM command ZQCL */ |
| [1] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_ZQCS, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = 400, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = 1024, |
| .rowbits = 6, |
| .bank = 0, |
| .rank = 0, |
| }, |
| .addr_update = { |
| .inc_rank = 1, |
| .addr_wrap = 20, |
| }, |
| }, |
| }; |
| iosav_write_sequence(BROADCAST_CH, zqcl_sequence, ARRAY_SIZE(zqcl_sequence)); |
| |
| /* Execute command queue on all channels. Do it four times. */ |
| iosav_run_queue(BROADCAST_CH, 4, 0); |
| |
| FOR_ALL_CHANNELS { |
| /* Wait for ref drained */ |
| wait_for_iosav(channel); |
| } |
| |
| /* Refresh enable */ |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 3); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| MCHBAR32_AND(SCHED_CBIT_ch(channel), ~(1 << 21)); |
| |
| wait_for_iosav(channel); |
| |
| slotrank = (ctrl->rankmap[channel] & 1) ? 0 : 2; |
| |
| /* Drain */ |
| wait_for_iosav(channel); |
| |
| iosav_write_zqcs_sequence(channel, slotrank, 4, 101, 31); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| /* Drain */ |
| wait_for_iosav(channel); |
| } |
| } |
| |
| static const u32 lane_base[] = { |
| LANEBASE_B0, LANEBASE_B1, LANEBASE_B2, LANEBASE_B3, |
| LANEBASE_B4, LANEBASE_B5, LANEBASE_B6, LANEBASE_B7, |
| LANEBASE_ECC |
| }; |
| |
| void program_timings(ramctr_timing *ctrl, int channel) |
| { |
| u32 reg_roundtrip_latency, reg_pi_code, reg_logic_delay, reg_io_latency; |
| int lane; |
| int slotrank, slot; |
| int full_shift = 0; |
| u16 pi_coding_ctrl[NUM_SLOTS]; |
| |
| FOR_ALL_POPULATED_RANKS { |
| if (full_shift < -ctrl->timings[channel][slotrank].pi_coding) |
| full_shift = -ctrl->timings[channel][slotrank].pi_coding; |
| } |
| |
| for (slot = 0; slot < NUM_SLOTS; slot++) |
| switch ((ctrl->rankmap[channel] >> (2 * slot)) & 3) { |
| case 0: |
| default: |
| pi_coding_ctrl[slot] = 0x7f; |
| break; |
| case 1: |
| pi_coding_ctrl[slot] = |
| ctrl->timings[channel][2 * slot + 0].pi_coding + full_shift; |
| break; |
| case 2: |
| pi_coding_ctrl[slot] = |
| ctrl->timings[channel][2 * slot + 1].pi_coding + full_shift; |
| break; |
| case 3: |
| pi_coding_ctrl[slot] = |
| (ctrl->timings[channel][2 * slot].pi_coding + |
| ctrl->timings[channel][2 * slot + 1].pi_coding) / 2 + full_shift; |
| break; |
| } |
| |
| /* Enable CMD XOVER */ |
| union gdcr_cmd_pi_coding_reg cmd_pi_coding = { |
| .raw = get_XOVER_CMD(ctrl->rankmap[channel]), |
| }; |
| cmd_pi_coding.cmd_pi_code = full_shift & 0x3f; |
| cmd_pi_coding.cmd_logic_delay = !!(full_shift & 0x40); |
| |
| cmd_pi_coding.ctl_pi_code_d0 = pi_coding_ctrl[0] & 0x3f; |
| cmd_pi_coding.ctl_pi_code_d1 = pi_coding_ctrl[1] & 0x3f; |
| cmd_pi_coding.ctl_logic_delay_d0 = !!(pi_coding_ctrl[0] & 0x40); |
| cmd_pi_coding.ctl_logic_delay_d1 = !!(pi_coding_ctrl[1] & 0x40); |
| |
| MCHBAR32(GDCRCMDPICODING_ch(channel)) = cmd_pi_coding.raw; |
| |
| /* Enable CLK XOVER */ |
| reg_pi_code = get_XOVER_CLK(ctrl->rankmap[channel]); |
| reg_logic_delay = 0; |
| |
| FOR_ALL_POPULATED_RANKS { |
| int shift = ctrl->timings[channel][slotrank].pi_coding + full_shift; |
| int offset_pi_code; |
| if (shift < 0) |
| shift = 0; |
| |
| offset_pi_code = ctrl->pi_code_offset + shift; |
| |
| /* Set CLK phase shift */ |
| reg_pi_code |= (offset_pi_code & 0x3f) << (6 * slotrank); |
| reg_logic_delay |= ((offset_pi_code >> 6) & 1) << slotrank; |
| } |
| |
| MCHBAR32(GDCRCKPICODE_ch(channel)) = reg_pi_code; |
| MCHBAR32(GDCRCKLOGICDELAY_ch(channel)) = reg_logic_delay; |
| |
| reg_io_latency = MCHBAR32(SC_IO_LATENCY_ch(channel)); |
| reg_io_latency &= ~0xffff; |
| |
| reg_roundtrip_latency = 0; |
| |
| FOR_ALL_POPULATED_RANKS { |
| int post_timA_min_high = 7, pre_timA_min_high = 7; |
| int post_timA_max_high = 0, pre_timA_max_high = 0; |
| int shift_402x = 0; |
| int shift = ctrl->timings[channel][slotrank].pi_coding + full_shift; |
| |
| if (shift < 0) |
| shift = 0; |
| |
| FOR_ALL_LANES { |
| post_timA_min_high = MIN(post_timA_min_high, |
| (ctrl->timings[channel][slotrank].lanes[lane]. |
| timA + shift) >> 6); |
| pre_timA_min_high = MIN(pre_timA_min_high, |
| ctrl->timings[channel][slotrank].lanes[lane]. |
| timA >> 6); |
| post_timA_max_high = MAX(post_timA_max_high, |
| (ctrl->timings[channel][slotrank].lanes[lane]. |
| timA + shift) >> 6); |
| pre_timA_max_high = MAX(pre_timA_max_high, |
| ctrl->timings[channel][slotrank].lanes[lane]. |
| timA >> 6); |
| } |
| |
| if (pre_timA_max_high - pre_timA_min_high < |
| post_timA_max_high - post_timA_min_high) |
| shift_402x = +1; |
| |
| else if (pre_timA_max_high - pre_timA_min_high > |
| post_timA_max_high - post_timA_min_high) |
| shift_402x = -1; |
| |
| reg_io_latency |= |
| (ctrl->timings[channel][slotrank].io_latency + shift_402x - |
| post_timA_min_high) << (4 * slotrank); |
| |
| reg_roundtrip_latency |= |
| (ctrl->timings[channel][slotrank].roundtrip_latency + |
| shift_402x) << (8 * slotrank); |
| |
| FOR_ALL_LANES { |
| MCHBAR32(lane_base[lane] + GDCRRX(channel, slotrank)) = |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timA + shift) & 0x3f) |
| | |
| ((ctrl->timings[channel][slotrank].lanes[lane]. |
| rising + shift) << 8) |
| | |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timA + shift - |
| (post_timA_min_high << 6)) & 0x1c0) << 10) |
| | ((ctrl->timings[channel][slotrank].lanes[lane]. |
| falling + shift) << 20)); |
| |
| MCHBAR32(lane_base[lane] + GDCRTX(channel, slotrank)) = |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timC + shift) & 0x3f) |
| | |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timB + shift) & 0x3f) << 8) |
| | |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timB + shift) & 0x1c0) << 9) |
| | |
| (((ctrl->timings[channel][slotrank].lanes[lane]. |
| timC + shift) & 0x40) << 13)); |
| } |
| } |
| MCHBAR32(SC_ROUNDT_LAT_ch(channel)) = reg_roundtrip_latency; |
| MCHBAR32(SC_IO_LATENCY_ch(channel)) = reg_io_latency; |
| } |
| |
| static void test_timA(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| wait_for_iosav(channel); |
| |
| iosav_write_read_mpr_sequence(channel, slotrank, ctrl->tMOD, 1, 3, 15, ctrl->CAS + 36); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| static int does_lane_work(ramctr_timing *ctrl, int channel, int slotrank, int lane) |
| { |
| u32 timA = ctrl->timings[channel][slotrank].lanes[lane].timA; |
| |
| return (MCHBAR32(lane_base[lane] + |
| GDCRTRAININGRESULT(channel, (timA / 32) & 1)) >> (timA % 32)) & 1; |
| } |
| |
| struct run { |
| int middle; |
| int end; |
| int start; |
| int all; |
| int length; |
| }; |
| |
| static struct run get_longest_zero_run(int *seq, int sz) |
| { |
| int i, ls; |
| int bl = 0, bs = 0; |
| struct run ret; |
| |
| ls = 0; |
| for (i = 0; i < 2 * sz; i++) |
| if (seq[i % sz]) { |
| if (i - ls > bl) { |
| bl = i - ls; |
| bs = ls; |
| } |
| ls = i + 1; |
| } |
| if (bl == 0) { |
| ret.middle = sz / 2; |
| ret.start = 0; |
| ret.end = sz; |
| ret.length = sz; |
| ret.all = 1; |
| return ret; |
| } |
| |
| ret.start = bs % sz; |
| ret.end = (bs + bl - 1) % sz; |
| ret.middle = (bs + (bl - 1) / 2) % sz; |
| ret.length = bl; |
| ret.all = 0; |
| |
| return ret; |
| } |
| |
| static void find_rcven_pi_coarse(ramctr_timing *ctrl, int channel, int slotrank, int *upperA) |
| { |
| int timA; |
| int statistics[NUM_LANES][128]; |
| int lane; |
| |
| for (timA = 0; timA < 128; timA++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timA = timA; |
| } |
| program_timings(ctrl, channel); |
| |
| test_timA(ctrl, channel, slotrank); |
| |
| FOR_ALL_LANES { |
| statistics[lane][timA] = !does_lane_work(ctrl, channel, slotrank, lane); |
| } |
| } |
| FOR_ALL_LANES { |
| struct run rn = get_longest_zero_run(statistics[lane], 128); |
| ctrl->timings[channel][slotrank].lanes[lane].timA = rn.middle; |
| upperA[lane] = rn.end; |
| if (upperA[lane] < rn.middle) |
| upperA[lane] += 128; |
| |
| printram("timA: %d, %d, %d: 0x%02x-0x%02x-0x%02x\n", |
| channel, slotrank, lane, rn.start, rn.middle, rn.end); |
| } |
| } |
| |
| static void fine_tune_rcven_pi(ramctr_timing *ctrl, int channel, int slotrank, int *upperA) |
| { |
| int timA_delta; |
| int statistics[NUM_LANES][51]; |
| int lane, i; |
| |
| memset(statistics, 0, sizeof(statistics)); |
| |
| for (timA_delta = -25; timA_delta <= 25; timA_delta++) { |
| |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timA |
| = upperA[lane] + timA_delta + 0x40; |
| } |
| program_timings(ctrl, channel); |
| |
| for (i = 0; i < 100; i++) { |
| test_timA(ctrl, channel, slotrank); |
| FOR_ALL_LANES { |
| statistics[lane][timA_delta + 25] += |
| does_lane_work(ctrl, channel, slotrank, lane); |
| } |
| } |
| } |
| FOR_ALL_LANES { |
| int last_zero, first_all; |
| |
| for (last_zero = -25; last_zero <= 25; last_zero++) |
| if (statistics[lane][last_zero + 25]) |
| break; |
| |
| last_zero--; |
| for (first_all = -25; first_all <= 25; first_all++) |
| if (statistics[lane][first_all + 25] == 100) |
| break; |
| |
| printram("lane %d: %d, %d\n", lane, last_zero, first_all); |
| |
| ctrl->timings[channel][slotrank].lanes[lane].timA = |
| (last_zero + first_all) / 2 + upperA[lane]; |
| |
| printram("Aval: %d, %d, %d: %x\n", channel, slotrank, |
| lane, ctrl->timings[channel][slotrank].lanes[lane].timA); |
| } |
| } |
| |
| static int find_roundtrip_latency(ramctr_timing *ctrl, int channel, int slotrank, int *upperA) |
| { |
| int works[NUM_LANES]; |
| int lane; |
| |
| while (1) { |
| int all_works = 1, some_works = 0; |
| |
| program_timings(ctrl, channel); |
| test_timA(ctrl, channel, slotrank); |
| |
| FOR_ALL_LANES { |
| works[lane] = !does_lane_work(ctrl, channel, slotrank, lane); |
| |
| if (works[lane]) |
| some_works = 1; |
| else |
| all_works = 0; |
| } |
| if (all_works) |
| return 0; |
| |
| if (!some_works) { |
| if (ctrl->timings[channel][slotrank].roundtrip_latency < 2) { |
| printk(BIOS_EMERG, "402x discovery failed (1): %d, %d\n", |
| channel, slotrank); |
| return MAKE_ERR; |
| } |
| ctrl->timings[channel][slotrank].roundtrip_latency -= 2; |
| printram("4024 -= 2;\n"); |
| continue; |
| } |
| ctrl->timings[channel][slotrank].io_latency += 2; |
| printram("4028 += 2;\n"); |
| |
| if (ctrl->timings[channel][slotrank].io_latency >= 0x10) { |
| printk(BIOS_EMERG, "402x discovery failed (2): %d, %d\n", |
| channel, slotrank); |
| return MAKE_ERR; |
| } |
| FOR_ALL_LANES if (works[lane]) { |
| ctrl->timings[channel][slotrank].lanes[lane].timA += 128; |
| upperA[lane] += 128; |
| printram("increment %d, %d, %d\n", channel, slotrank, lane); |
| } |
| } |
| return 0; |
| } |
| |
| static int get_logic_delay_delta(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| int lane; |
| u16 logic_delay_min = 7; |
| u16 logic_delay_max = 0; |
| |
| FOR_ALL_LANES { |
| const u16 logic_delay = ctrl->timings[channel][slotrank].lanes[lane].timA >> 6; |
| |
| logic_delay_min = MIN(logic_delay_min, logic_delay); |
| logic_delay_max = MAX(logic_delay_max, logic_delay); |
| } |
| |
| if (logic_delay_max < logic_delay_min) { |
| printk(BIOS_EMERG, "Logic delay max < min (%u < %u): %d, %d\n", |
| logic_delay_max, logic_delay_min, channel, slotrank); |
| } |
| |
| assert(logic_delay_max >= logic_delay_min); |
| |
| return logic_delay_max - logic_delay_min; |
| } |
| |
| static int align_rt_io_latency(ramctr_timing *ctrl, int channel, int slotrank, int prev) |
| { |
| int latency_offset = 0; |
| |
| /* Get changed maxima */ |
| const int post = get_logic_delay_delta(ctrl, channel, slotrank); |
| |
| if (prev < post) |
| latency_offset = +1; |
| |
| else if (prev > post) |
| latency_offset = -1; |
| |
| else |
| latency_offset = 0; |
| |
| ctrl->timings[channel][slotrank].io_latency += latency_offset; |
| ctrl->timings[channel][slotrank].roundtrip_latency += latency_offset; |
| printram("4024 += %d;\n", latency_offset); |
| printram("4028 += %d;\n", latency_offset); |
| |
| return post; |
| } |
| |
| static void compute_final_logic_delay(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| u16 logic_delay_min = 7; |
| int lane; |
| |
| FOR_ALL_LANES { |
| const u16 logic_delay = ctrl->timings[channel][slotrank].lanes[lane].timA >> 6; |
| |
| logic_delay_min = MIN(logic_delay_min, logic_delay); |
| } |
| |
| if (logic_delay_min >= 2) { |
| printk(BIOS_WARNING, "Logic delay %u greater than 1: %d %d\n", |
| logic_delay_min, channel, slotrank); |
| } |
| |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timA -= logic_delay_min << 6; |
| } |
| ctrl->timings[channel][slotrank].io_latency -= logic_delay_min; |
| printram("4028 -= %d;\n", logic_delay_min); |
| } |
| |
| int receive_enable_calibration(ramctr_timing *ctrl) |
| { |
| int channel, slotrank, lane; |
| int err; |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| int all_high, some_high; |
| int upperA[NUM_LANES]; |
| int prev; |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_prea_sequence(channel, slotrank, ctrl->tRP, 0); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| const union gdcr_training_mod_reg training_mod = { |
| .receive_enable_mode = 1, |
| .training_rank_sel = slotrank, |
| .odt_always_on = 1, |
| }; |
| MCHBAR32(GDCRTRAININGMOD) = training_mod.raw; |
| |
| ctrl->timings[channel][slotrank].io_latency = 4; |
| ctrl->timings[channel][slotrank].roundtrip_latency = 55; |
| program_timings(ctrl, channel); |
| |
| find_rcven_pi_coarse(ctrl, channel, slotrank, upperA); |
| |
| all_high = 1; |
| some_high = 0; |
| FOR_ALL_LANES { |
| if (ctrl->timings[channel][slotrank].lanes[lane].timA >= 0x40) |
| some_high = 1; |
| else |
| all_high = 0; |
| } |
| |
| if (all_high) { |
| ctrl->timings[channel][slotrank].io_latency--; |
| printram("4028--;\n"); |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timA -= 0x40; |
| upperA[lane] -= 0x40; |
| |
| } |
| } else if (some_high) { |
| ctrl->timings[channel][slotrank].roundtrip_latency++; |
| ctrl->timings[channel][slotrank].io_latency++; |
| printram("4024++;\n"); |
| printram("4028++;\n"); |
| } |
| |
| program_timings(ctrl, channel); |
| |
| prev = get_logic_delay_delta(ctrl, channel, slotrank); |
| |
| err = find_roundtrip_latency(ctrl, channel, slotrank, upperA); |
| if (err) |
| return err; |
| |
| prev = align_rt_io_latency(ctrl, channel, slotrank, prev); |
| |
| fine_tune_rcven_pi(ctrl, channel, slotrank, upperA); |
| |
| prev = align_rt_io_latency(ctrl, channel, slotrank, prev); |
| |
| compute_final_logic_delay(ctrl, channel, slotrank); |
| |
| align_rt_io_latency(ctrl, channel, slotrank, prev); |
| |
| printram("4/8: %d, %d, %x, %x\n", channel, slotrank, |
| ctrl->timings[channel][slotrank].roundtrip_latency, |
| ctrl->timings[channel][slotrank].io_latency); |
| |
| printram("final results:\n"); |
| FOR_ALL_LANES |
| printram("Aval: %d, %d, %d: %x\n", channel, slotrank, lane, |
| ctrl->timings[channel][slotrank].lanes[lane].timA); |
| |
| MCHBAR32(GDCRTRAININGMOD) = 0; |
| |
| toggle_io_reset(); |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| program_timings(ctrl, channel); |
| } |
| |
| return 0; |
| } |
| |
| static void test_tx_dq(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| int lane; |
| |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)) = 0; |
| MCHBAR32(IOSAV_By_BW_SERROR_C_ch(channel, lane)); |
| } |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_misc_write_sequence(ctrl, channel, slotrank, |
| MAX(ctrl->tRRD, (ctrl->tFAW >> 2) + 1), 4, 4, 500, 18); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_prea_act_read_sequence(ctrl, channel, slotrank); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| static void tx_dq_threshold_process(int *data, const int count) |
| { |
| int min = data[0]; |
| int max = min; |
| int i; |
| for (i = 1; i < count; i++) { |
| if (min > data[i]) |
| min = data[i]; |
| |
| if (max < data[i]) |
| max = data[i]; |
| } |
| int threshold = min / 2 + max / 2; |
| for (i = 0; i < count; i++) |
| data[i] = data[i] > threshold; |
| |
| printram("threshold=%d min=%d max=%d\n", threshold, min, max); |
| } |
| |
| static int tx_dq_write_leveling(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| int tx_dq; |
| int stats[NUM_LANES][MAX_TIMC + 1]; |
| int lane; |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_prea_sequence(channel, slotrank, ctrl->tRP, 18); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| for (tx_dq = 0; tx_dq <= MAX_TIMC; tx_dq++) { |
| FOR_ALL_LANES ctrl->timings[channel][slotrank].lanes[lane].timC = tx_dq; |
| program_timings(ctrl, channel); |
| |
| test_tx_dq(ctrl, channel, slotrank); |
| |
| FOR_ALL_LANES { |
| stats[lane][tx_dq] = MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)); |
| } |
| } |
| FOR_ALL_LANES { |
| struct run rn = get_longest_zero_run(stats[lane], ARRAY_SIZE(stats[lane])); |
| |
| if (rn.all || rn.length < 8) { |
| printk(BIOS_EMERG, "timC discovery failed: %d, %d, %d\n", |
| channel, slotrank, lane); |
| /* |
| * With command training not being done yet, the lane can be erroneous. |
| * Take the average as reference and try again to find a run. |
| */ |
| tx_dq_threshold_process(stats[lane], ARRAY_SIZE(stats[lane])); |
| rn = get_longest_zero_run(stats[lane], ARRAY_SIZE(stats[lane])); |
| |
| if (rn.all || rn.length < 8) { |
| printk(BIOS_EMERG, "timC recovery failed\n"); |
| return MAKE_ERR; |
| } |
| } |
| ctrl->timings[channel][slotrank].lanes[lane].timC = rn.middle; |
| printram("timC: %d, %d, %d: 0x%02x-0x%02x-0x%02x\n", |
| channel, slotrank, lane, rn.start, rn.middle, rn.end); |
| } |
| return 0; |
| } |
| |
| static int get_precedening_channels(ramctr_timing *ctrl, int target_channel) |
| { |
| int channel, ret = 0; |
| |
| FOR_ALL_POPULATED_CHANNELS if (channel < target_channel) |
| ret++; |
| |
| return ret; |
| } |
| |
| /* Each cacheline is 64 bits long */ |
| static void program_wdb_pattern_length(int channel, const unsigned int num_cachelines) |
| { |
| MCHBAR8(IOSAV_DATA_CTL_ch(channel)) = num_cachelines / 8 - 1; |
| } |
| |
| static void fill_pattern0(ramctr_timing *ctrl, int channel, u32 a, u32 b) |
| { |
| unsigned int j; |
| unsigned int channel_offset = get_precedening_channels(ctrl, channel) * 0x40; |
| |
| for (j = 0; j < 16; j++) |
| write32((void *)(0x04000000 + channel_offset + 4 * j), j & 2 ? b : a); |
| |
| sfence(); |
| |
| program_wdb_pattern_length(channel, 8); |
| } |
| |
| static int num_of_channels(const ramctr_timing *ctrl) |
| { |
| int ret = 0; |
| int channel; |
| FOR_ALL_POPULATED_CHANNELS ret++; |
| return ret; |
| } |
| |
| static void fill_pattern1(ramctr_timing *ctrl, int channel) |
| { |
| unsigned int j; |
| unsigned int channel_offset = get_precedening_channels(ctrl, channel) * 0x40; |
| unsigned int channel_step = 0x40 * num_of_channels(ctrl); |
| |
| for (j = 0; j < 16; j++) |
| write32((void *)(0x04000000 + channel_offset + j * 4), 0xffffffff); |
| |
| for (j = 0; j < 16; j++) |
| write32((void *)(0x04000000 + channel_offset + channel_step + j * 4), 0); |
| |
| sfence(); |
| |
| program_wdb_pattern_length(channel, 16); |
| } |
| |
| static int write_level_rank(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| int timB; |
| int statistics[NUM_LANES][128]; |
| int lane; |
| |
| const union gdcr_training_mod_reg training_mod = { |
| .write_leveling_mode = 1, |
| .training_rank_sel = slotrank, |
| .enable_dqs_wl = 5, |
| .odt_always_on = 1, |
| .force_drive_enable = 1, |
| }; |
| MCHBAR32(GDCRTRAININGMOD) = training_mod.raw; |
| |
| u32 mr1reg = make_mr1(ctrl, slotrank, channel) | 1 << 7; |
| int bank = 1; |
| |
| if (ctrl->rank_mirror[channel][slotrank]) |
| ddr3_mirror_mrreg(&bank, &mr1reg); |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_jedec_write_leveling_sequence(ctrl, channel, slotrank, bank, mr1reg); |
| |
| for (timB = 0; timB < 128; timB++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timB = timB; |
| } |
| program_timings(ctrl, channel); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| |
| FOR_ALL_LANES { |
| statistics[lane][timB] = !((MCHBAR32(lane_base[lane] + |
| GDCRTRAININGRESULT(channel, (timB / 32) & 1)) >> |
| (timB % 32)) & 1); |
| } |
| } |
| FOR_ALL_LANES { |
| struct run rn = get_longest_zero_run(statistics[lane], 128); |
| /* |
| * timC is a direct function of timB's 6 LSBs. Some tests increments the value |
| * of timB by a small value, which might cause the 6-bit value to overflow if |
| * it's close to 0x3f. Increment the value by a small offset if it's likely |
| * to overflow, to make sure it won't overflow while running tests and bricks |
| * the system due to a non matching timC. |
| * |
| * TODO: find out why some tests (edge write discovery) increment timB. |
| */ |
| if ((rn.start & 0x3f) == 0x3e) |
| rn.start += 2; |
| else if ((rn.start & 0x3f) == 0x3f) |
| rn.start += 1; |
| |
| ctrl->timings[channel][slotrank].lanes[lane].timB = rn.start; |
| if (rn.all) { |
| printk(BIOS_EMERG, "timB discovery failed: %d, %d, %d\n", |
| channel, slotrank, lane); |
| |
| return MAKE_ERR; |
| } |
| printram("timB: %d, %d, %d: 0x%02x-0x%02x-0x%02x\n", |
| channel, slotrank, lane, rn.start, rn.middle, rn.end); |
| } |
| return 0; |
| } |
| |
| static int get_dqs_flyby_adjust(u64 val) |
| { |
| int i; |
| /* DQS is good enough */ |
| if (val == 0xffffffffffffffffLL) |
| return 0; |
| if (val >= 0xf000000000000000LL) { |
| /* DQS is late, needs negative adjustment */ |
| for (i = 0; i < 8; i++) |
| if (val << (8 * (7 - i) + 4)) |
| return -i; |
| } else { |
| /* DQS is early, needs positive adjustment */ |
| for (i = 0; i < 8; i++) |
| if (val >> (8 * (7 - i) + 4)) |
| return i; |
| } |
| return 8; |
| } |
| |
| static void train_write_flyby(ramctr_timing *ctrl) |
| { |
| int channel, slotrank, lane, old; |
| |
| const union gdcr_training_mod_reg training_mod = { |
| .dq_dqs_training_res = 1, |
| }; |
| MCHBAR32(GDCRTRAININGMOD) = training_mod.raw; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| fill_pattern1(ctrl, channel); |
| } |
| FOR_ALL_POPULATED_CHANNELS FOR_ALL_POPULATED_RANKS { |
| |
| /* Reset read and write WDB pointers */ |
| MCHBAR32(IOSAV_DATA_CTL_ch(channel)) = 0x10001; |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_misc_write_sequence(ctrl, channel, slotrank, 3, 1, 3, 3, 31); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| |
| const struct iosav_ssq rd_sequence[] = { |
| /* DRAM command PREA */ |
| [0] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_PRE, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 3, |
| .post_ssq_wait = ctrl->tRP, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = 1024, |
| .rowbits = 6, |
| .bank = 0, |
| .rank = slotrank, |
| }, |
| .addr_update = { |
| .addr_wrap = 18, |
| }, |
| }, |
| /* DRAM command ACT */ |
| [1] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_ACT, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 3, |
| .post_ssq_wait = ctrl->tRCD, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = 0, |
| .rowbits = 6, |
| .bank = 0, |
| .rank = slotrank, |
| }, |
| }, |
| /* DRAM command RD */ |
| [2] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_RD, |
| .ranksel_ap = 3, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 3, |
| .post_ssq_wait = ctrl->tRP + |
| ctrl->timings[channel][slotrank].roundtrip_latency + |
| ctrl->timings[channel][slotrank].io_latency, |
| .data_direction = SSQ_RD, |
| }, |
| .sp_cmd_addr = { |
| .address = 8, |
| .rowbits = 6, |
| .bank = 0, |
| .rank = slotrank, |
| }, |
| }, |
| }; |
| iosav_write_sequence(channel, rd_sequence, ARRAY_SIZE(rd_sequence)); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| FOR_ALL_LANES { |
| u64 res = MCHBAR32(lane_base[lane] + GDCRTRAININGRESULT1(channel)); |
| res |= ((u64) MCHBAR32(lane_base[lane] + |
| GDCRTRAININGRESULT2(channel))) << 32; |
| |
| old = ctrl->timings[channel][slotrank].lanes[lane].timB; |
| ctrl->timings[channel][slotrank].lanes[lane].timB += |
| get_dqs_flyby_adjust(res) * 64; |
| |
| printram("High adjust %d:%016llx\n", lane, res); |
| printram("Bval+: %d, %d, %d, %x -> %x\n", channel, slotrank, lane, |
| old, ctrl->timings[channel][slotrank].lanes[lane].timB); |
| } |
| } |
| MCHBAR32(GDCRTRAININGMOD) = 0; |
| } |
| |
| static void disable_refresh_machine(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| /* choose an existing rank */ |
| const int slotrank = !(ctrl->rankmap[channel] & 1) ? 2 : 0; |
| |
| iosav_write_zqcs_sequence(channel, slotrank, 4, 4, 31); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| |
| MCHBAR32_OR(SCHED_CBIT_ch(channel), 1 << 21); |
| } |
| |
| /* Refresh disable */ |
| MCHBAR32_AND(MC_INIT_STATE_G, ~(1 << 3)); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| /* Execute the same command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| } |
| |
| /* |
| * Compensate the skew between CMD/ADDR/CLK and DQ/DQS lanes. |
| * |
| * Since DDR3 uses a fly-by topology, the data and strobes signals reach the chips at different |
| * times with respect to command, address and clock signals. By delaying either all DQ/DQS or |
| * all CMD/ADDR/CLK signals, a full phase shift can be introduced. It is assumed that the |
| * CLK/ADDR/CMD signals have the same routing delay. |
| * |
| * To find the required phase shift the DRAM is placed in "write leveling" mode. In this mode, |
| * the DRAM-chip samples the CLK on every DQS edge and feeds back the sampled value on the data |
| * lanes (DQ). |
| */ |
| static int jedec_write_leveling(ramctr_timing *ctrl) |
| { |
| int channel, slotrank; |
| |
| disable_refresh_machine(ctrl); |
| |
| /* Enable write leveling on all ranks |
| Disable all DQ outputs |
| Only NOP is allowed in this mode */ |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS |
| write_mrreg(ctrl, channel, slotrank, 1, |
| make_mr1(ctrl, slotrank, channel) | 1 << 12 | 1 << 7); |
| |
| /* Needs to be programmed before I/O reset below */ |
| const union gdcr_training_mod_reg training_mod = { |
| .write_leveling_mode = 1, |
| .enable_dqs_wl = 5, |
| .odt_always_on = 1, |
| .force_drive_enable = 1, |
| }; |
| MCHBAR32(GDCRTRAININGMOD) = training_mod.raw; |
| |
| toggle_io_reset(); |
| |
| /* Set any valid value for timB, it gets corrected later */ |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| const int err = write_level_rank(ctrl, channel, slotrank); |
| if (err) |
| return err; |
| } |
| |
| /* Disable write leveling on all ranks */ |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS |
| write_mrreg(ctrl, channel, slotrank, 1, make_mr1(ctrl, slotrank, channel)); |
| |
| MCHBAR32(GDCRTRAININGMOD) = 0; |
| |
| FOR_ALL_POPULATED_CHANNELS |
| wait_for_iosav(channel); |
| |
| /* Refresh enable */ |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 3); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| MCHBAR32_AND(SCHED_CBIT_ch(channel), ~(1 << 21)); |
| MCHBAR32(IOSAV_STATUS_ch(channel)); |
| wait_for_iosav(channel); |
| |
| iosav_write_zqcs_sequence(channel, 0, 4, 101, 31); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| toggle_io_reset(); |
| |
| return 0; |
| } |
| |
| int write_training(ramctr_timing *ctrl) |
| { |
| int channel, slotrank; |
| int err; |
| |
| FOR_ALL_POPULATED_CHANNELS |
| MCHBAR32_OR(TC_RWP_ch(channel), 1 << 27); |
| |
| printram("CPE\n"); |
| |
| err = jedec_write_leveling(ctrl); |
| if (err) |
| return err; |
| |
| printram("CPF\n"); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| fill_pattern0(ctrl, channel, 0xaaaaaaaa, 0x55555555); |
| } |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| err = tx_dq_write_leveling(ctrl, channel, slotrank); |
| if (err) |
| return err; |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS |
| program_timings(ctrl, channel); |
| |
| /* measure and adjust timB timings */ |
| train_write_flyby(ctrl); |
| |
| FOR_ALL_POPULATED_CHANNELS |
| program_timings(ctrl, channel); |
| |
| return 0; |
| } |
| |
| static int test_command_training(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| struct ram_rank_timings saved_rt = ctrl->timings[channel][slotrank]; |
| int timC_delta; |
| int lanes_ok = 0; |
| int ctr = 0; |
| int lane; |
| |
| for (timC_delta = -5; timC_delta <= 5; timC_delta++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].timC = |
| saved_rt.lanes[lane].timC + timC_delta; |
| } |
| program_timings(ctrl, channel); |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT(lane)) = 0; |
| } |
| |
| /* Reset read WDB pointer */ |
| MCHBAR32(IOSAV_DATA_CTL_ch(channel)) = 0x1f; |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_command_training_sequence(ctrl, channel, slotrank, ctr); |
| |
| /* Program LFSR for the RD/WR subsequences */ |
| MCHBAR32(IOSAV_n_ADDRESS_LFSR_ch(channel, 1)) = 0x389abcd; |
| MCHBAR32(IOSAV_n_ADDRESS_LFSR_ch(channel, 2)) = 0x389abcd; |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| FOR_ALL_LANES { |
| u32 r32 = MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)); |
| |
| if (r32 == 0) |
| lanes_ok |= 1 << lane; |
| } |
| ctr++; |
| if (lanes_ok == ((1 << ctrl->lanes) - 1)) |
| break; |
| } |
| |
| ctrl->timings[channel][slotrank] = saved_rt; |
| |
| return lanes_ok != ((1 << ctrl->lanes) - 1); |
| } |
| |
| static void fill_pattern5(ramctr_timing *ctrl, int channel, int patno) |
| { |
| unsigned int i, j; |
| unsigned int offset = get_precedening_channels(ctrl, channel) * 0x40; |
| unsigned int step = 0x40 * num_of_channels(ctrl); |
| |
| if (patno) { |
| u8 base8 = 0x80 >> ((patno - 1) % 8); |
| u32 base = base8 | (base8 << 8) | (base8 << 16) | (base8 << 24); |
| for (i = 0; i < 32; i++) { |
| for (j = 0; j < 16; j++) { |
| u32 val = use_base[patno - 1][i] & (1 << (j / 2)) ? base : 0; |
| |
| if (invert[patno - 1][i] & (1 << (j / 2))) |
| val = ~val; |
| |
| write32((void *)((1 << 26) + offset + i * step + j * 4), val); |
| } |
| } |
| } else { |
| for (i = 0; i < ARRAY_SIZE(pattern); i++) { |
| for (j = 0; j < 16; j++) { |
| const u32 val = pattern[i][j]; |
| write32((void *)((1 << 26) + offset + i * step + j * 4), val); |
| } |
| } |
| sfence(); |
| } |
| |
| program_wdb_pattern_length(channel, 256); |
| } |
| |
| static void reprogram_320c(ramctr_timing *ctrl) |
| { |
| disable_refresh_machine(ctrl); |
| |
| /* JEDEC reset */ |
| dram_jedecreset(ctrl); |
| |
| /* MRS commands */ |
| dram_mrscommands(ctrl); |
| |
| toggle_io_reset(); |
| } |
| |
| #define CT_MIN_PI -127 |
| #define CT_MAX_PI 128 |
| #define CT_PI_LENGTH (CT_MAX_PI - CT_MIN_PI + 1) |
| |
| #define MIN_C320C_LEN 13 |
| |
| static int try_cmd_stretch(ramctr_timing *ctrl, int channel, int cmd_stretch) |
| { |
| struct ram_rank_timings saved_timings[NUM_CHANNELS][NUM_SLOTRANKS]; |
| int slotrank; |
| int command_pi; |
| int stat[NUM_SLOTRANKS][CT_PI_LENGTH]; |
| int delta = 0; |
| |
| printram("Trying cmd_stretch %d on channel %d\n", cmd_stretch, channel); |
| |
| FOR_ALL_POPULATED_RANKS { |
| saved_timings[channel][slotrank] = ctrl->timings[channel][slotrank]; |
| } |
| |
| ctrl->cmd_stretch[channel] = cmd_stretch; |
| |
| const union tc_rap_reg tc_rap = { |
| .tRRD = ctrl->tRRD, |
| .tRTP = ctrl->tRTP, |
| .tCKE = ctrl->tCKE, |
| .tWTR = ctrl->tWTR, |
| .tFAW = ctrl->tFAW, |
| .tWR = ctrl->tWR, |
| .tCMD = ctrl->cmd_stretch[channel], |
| }; |
| MCHBAR32(TC_RAP_ch(channel)) = tc_rap.raw; |
| |
| if (ctrl->cmd_stretch[channel] == 2) |
| delta = 2; |
| else if (ctrl->cmd_stretch[channel] == 0) |
| delta = 4; |
| |
| FOR_ALL_POPULATED_RANKS { |
| ctrl->timings[channel][slotrank].roundtrip_latency -= delta; |
| } |
| |
| for (command_pi = CT_MIN_PI; command_pi < CT_MAX_PI; command_pi++) { |
| FOR_ALL_POPULATED_RANKS { |
| ctrl->timings[channel][slotrank].pi_coding = command_pi; |
| } |
| program_timings(ctrl, channel); |
| reprogram_320c(ctrl); |
| FOR_ALL_POPULATED_RANKS { |
| stat[slotrank][command_pi - CT_MIN_PI] = |
| test_command_training(ctrl, channel, slotrank); |
| } |
| } |
| FOR_ALL_POPULATED_RANKS { |
| struct run rn = get_longest_zero_run(stat[slotrank], CT_PI_LENGTH - 1); |
| |
| ctrl->timings[channel][slotrank].pi_coding = rn.middle + CT_MIN_PI; |
| printram("cmd_stretch: %d, %d: 0x%02x-0x%02x-0x%02x\n", |
| channel, slotrank, rn.start, rn.middle, rn.end); |
| |
| if (rn.all || rn.length < MIN_C320C_LEN) { |
| FOR_ALL_POPULATED_RANKS { |
| ctrl->timings[channel][slotrank] = |
| saved_timings[channel][slotrank]; |
| } |
| return MAKE_ERR; |
| } |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Adjust CMD phase shift and try multiple command rates. |
| * A command rate of 2T doubles the time needed for address and command decode. |
| */ |
| int command_training(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| fill_pattern5(ctrl, channel, 0); |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| int cmdrate, err; |
| |
| /* |
| * Dual DIMM per channel: |
| * Issue: |
| * While c320c discovery seems to succeed raminit will fail in write training. |
| * |
| * Workaround: |
| * Skip 1T in dual DIMM mode, that's only supported by a few DIMMs. |
| * Only try 1T mode for XMP DIMMs that request it in dual DIMM mode. |
| * |
| * Single DIMM per channel: |
| * Try command rate 1T and 2T |
| */ |
| cmdrate = ((ctrl->rankmap[channel] & 0x5) == 0x5); |
| if (ctrl->tCMD) |
| /* XMP gives the CMD rate in clock ticks, not ns */ |
| cmdrate = MIN(DIV_ROUND_UP(ctrl->tCMD, 256) - 1, 1); |
| |
| for (; cmdrate < 2; cmdrate++) { |
| err = try_cmd_stretch(ctrl, channel, cmdrate << 1); |
| |
| if (!err) |
| break; |
| } |
| |
| if (err) { |
| printk(BIOS_EMERG, "c320c discovery failed\n"); |
| return err; |
| } |
| |
| printram("Using CMD rate %uT on channel %u\n", cmdrate + 1, channel); |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS |
| program_timings(ctrl, channel); |
| |
| reprogram_320c(ctrl); |
| return 0; |
| } |
| |
| static int find_read_mpr_margin(ramctr_timing *ctrl, int channel, int slotrank, int *edges) |
| { |
| int dqs_pi; |
| int stats[NUM_LANES][MAX_EDGE_TIMING + 1]; |
| int lane; |
| |
| for (dqs_pi = 0; dqs_pi <= MAX_EDGE_TIMING; dqs_pi++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].rising = dqs_pi; |
| ctrl->timings[channel][slotrank].lanes[lane].falling = dqs_pi; |
| } |
| program_timings(ctrl, channel); |
| |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)) = 0; |
| MCHBAR32(IOSAV_By_BW_SERROR_C_ch(channel, lane)); |
| } |
| |
| wait_for_iosav(channel); |
| |
| iosav_write_read_mpr_sequence( |
| channel, slotrank, ctrl->tMOD, 500, 4, 1, ctrl->CAS + 8); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| |
| FOR_ALL_LANES { |
| stats[lane][dqs_pi] = MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)); |
| } |
| } |
| |
| FOR_ALL_LANES { |
| struct run rn = get_longest_zero_run(stats[lane], MAX_EDGE_TIMING + 1); |
| edges[lane] = rn.middle; |
| |
| if (rn.all) { |
| printk(BIOS_EMERG, "edge discovery failed: %d, %d, %d\n", channel, |
| slotrank, lane); |
| return MAKE_ERR; |
| } |
| printram("eval %d, %d, %d: %02x\n", channel, slotrank, lane, edges[lane]); |
| } |
| return 0; |
| } |
| |
| static void find_predefined_pattern(ramctr_timing *ctrl, const int channel) |
| { |
| int slotrank, lane; |
| |
| fill_pattern0(ctrl, channel, 0, 0); |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_BW_MASK_ch(channel, lane)) = 0; |
| MCHBAR32(IOSAV_By_BW_SERROR_C_ch(channel, lane)); |
| } |
| |
| FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].falling = 16; |
| ctrl->timings[channel][slotrank].lanes[lane].rising = 16; |
| } |
| |
| program_timings(ctrl, channel); |
| |
| FOR_ALL_POPULATED_RANKS { |
| wait_for_iosav(channel); |
| |
| iosav_write_read_mpr_sequence( |
| channel, slotrank, ctrl->tMOD, 3, 4, 1, ctrl->CAS + 8); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| /* XXX: check any measured value ? */ |
| |
| FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].falling = 48; |
| ctrl->timings[channel][slotrank].lanes[lane].rising = 48; |
| } |
| |
| program_timings(ctrl, channel); |
| |
| FOR_ALL_POPULATED_RANKS { |
| wait_for_iosav(channel); |
| |
| iosav_write_read_mpr_sequence( |
| channel, slotrank, ctrl->tMOD, 3, 4, 1, ctrl->CAS + 8); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| /* XXX: check any measured value ? */ |
| |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_BW_MASK_ch(channel, lane)) = |
| ~MCHBAR32(IOSAV_By_BW_SERROR_ch(channel, lane)) & 0xff; |
| } |
| } |
| |
| int read_mpr_training(ramctr_timing *ctrl) |
| { |
| int falling_edges[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int rising_edges[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int channel, slotrank, lane; |
| int err; |
| |
| MCHBAR32(GDCRTRAININGMOD) = 0; |
| |
| toggle_io_reset(); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| find_predefined_pattern(ctrl, channel); |
| |
| fill_pattern0(ctrl, channel, 0, 0xffffffff); |
| } |
| |
| /* |
| * FIXME: Under some conditions, vendor BIOS sets both edges to the same value. It will |
| * also use a single loop. It would seem that it is a debugging configuration. |
| */ |
| MCHBAR32(IOSAV_DC_MASK) = 0x300; |
| printram("discover falling edges:\n[%x] = %x\n", IOSAV_DC_MASK, 0x300); |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| err = find_read_mpr_margin(ctrl, channel, slotrank, |
| falling_edges[channel][slotrank]); |
| if (err) |
| return err; |
| } |
| |
| MCHBAR32(IOSAV_DC_MASK) = 0x200; |
| printram("discover rising edges:\n[%x] = %x\n", IOSAV_DC_MASK, 0x200); |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| err = find_read_mpr_margin(ctrl, channel, slotrank, |
| rising_edges[channel][slotrank]); |
| if (err) |
| return err; |
| } |
| |
| MCHBAR32(IOSAV_DC_MASK) = 0; |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].falling = |
| falling_edges[channel][slotrank][lane]; |
| ctrl->timings[channel][slotrank].lanes[lane].rising = |
| rising_edges[channel][slotrank][lane]; |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| program_timings(ctrl, channel); |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_BW_MASK_ch(channel, lane)) = 0; |
| } |
| return 0; |
| } |
| |
| static int find_agrsv_read_margin(ramctr_timing *ctrl, int channel, int slotrank, int *edges) |
| { |
| const int rd_vref_offsets[] = { 0, 0xc, 0x2c }; |
| |
| u32 raw_stats[MAX_EDGE_TIMING + 1]; |
| int lower[NUM_LANES]; |
| int upper[NUM_LANES]; |
| int lane, i, read_pi, pat; |
| |
| FOR_ALL_LANES { |
| lower[lane] = 0; |
| upper[lane] = MAX_EDGE_TIMING; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(rd_vref_offsets); i++) { |
| const union gdcr_training_mod_reg training_mod = { |
| .vref_gen_ctl = rd_vref_offsets[i], |
| }; |
| MCHBAR32(GDCRTRAININGMOD_ch(channel)) = training_mod.raw; |
| printram("[%x] = 0x%08x\n", GDCRTRAININGMOD_ch(channel), training_mod.raw); |
| |
| for (pat = 0; pat < NUM_PATTERNS; pat++) { |
| fill_pattern5(ctrl, channel, pat); |
| printram("using pattern %d\n", pat); |
| |
| for (read_pi = 0; read_pi <= MAX_EDGE_TIMING; read_pi++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane]. |
| rising = read_pi; |
| ctrl->timings[channel][slotrank].lanes[lane]. |
| falling = read_pi; |
| } |
| program_timings(ctrl, channel); |
| |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)) = 0; |
| MCHBAR32(IOSAV_By_BW_SERROR_C_ch(channel, lane)); |
| } |
| wait_for_iosav(channel); |
| |
| iosav_write_data_write_sequence(ctrl, channel, slotrank); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane)); |
| } |
| |
| /* FIXME: This register only exists on Ivy Bridge */ |
| raw_stats[read_pi] = MCHBAR32(IOSAV_BYTE_SERROR_C_ch(channel)); |
| } |
| |
| FOR_ALL_LANES { |
| int stats[MAX_EDGE_TIMING + 1]; |
| struct run rn; |
| |
| for (read_pi = 0; read_pi <= MAX_EDGE_TIMING; read_pi++) |
| stats[read_pi] = !!(raw_stats[read_pi] & (1 << lane)); |
| |
| rn = get_longest_zero_run(stats, MAX_EDGE_TIMING + 1); |
| |
| printram("edges: %d, %d, %d: 0x%02x-0x%02x-0x%02x, " |
| "0x%02x-0x%02x\n", channel, slotrank, i, rn.start, |
| rn.middle, rn.end, rn.start + ctrl->edge_offset[i], |
| rn.end - ctrl->edge_offset[i]); |
| |
| lower[lane] = MAX(rn.start + ctrl->edge_offset[i], lower[lane]); |
| upper[lane] = MIN(rn.end - ctrl->edge_offset[i], upper[lane]); |
| |
| edges[lane] = (lower[lane] + upper[lane]) / 2; |
| if (rn.all || (lower[lane] > upper[lane])) { |
| printk(BIOS_EMERG, "edge write discovery failed: " |
| "%d, %d, %d\n", channel, slotrank, lane); |
| |
| return MAKE_ERR; |
| } |
| } |
| } |
| } |
| |
| /* Restore nominal Vref after training */ |
| MCHBAR32(GDCRTRAININGMOD_ch(channel)) = 0; |
| printram("CPA\n"); |
| return 0; |
| } |
| |
| int aggressive_read_training(ramctr_timing *ctrl) |
| { |
| int falling_edges[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int rising_edges[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int channel, slotrank, lane, err; |
| |
| /* |
| * FIXME: Under some conditions, vendor BIOS sets both edges to the same value. It will |
| * also use a single loop. It would seem that it is a debugging configuration. |
| */ |
| MCHBAR32(IOSAV_DC_MASK) = 0x300; |
| printram("discover falling edges aggressive:\n[%x] = %x\n", IOSAV_DC_MASK, 0x300); |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| err = find_agrsv_read_margin(ctrl, channel, slotrank, |
| falling_edges[channel][slotrank]); |
| if (err) |
| return err; |
| } |
| |
| MCHBAR32(IOSAV_DC_MASK) = 0x200; |
| printram("discover rising edges aggressive:\n[%x] = %x\n", IOSAV_DC_MASK, 0x200); |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| err = find_agrsv_read_margin(ctrl, channel, slotrank, |
| rising_edges[channel][slotrank]); |
| if (err) |
| return err; |
| } |
| |
| MCHBAR32(IOSAV_DC_MASK) = 0; |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank].lanes[lane].falling = |
| falling_edges[channel][slotrank][lane]; |
| |
| ctrl->timings[channel][slotrank].lanes[lane].rising = |
| rising_edges[channel][slotrank][lane]; |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS |
| program_timings(ctrl, channel); |
| |
| return 0; |
| } |
| |
| static void test_aggressive_write(ramctr_timing *ctrl, int channel, int slotrank) |
| { |
| wait_for_iosav(channel); |
| |
| iosav_write_aggressive_write_read_sequence(ctrl, channel, slotrank); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| } |
| |
| static void set_write_vref(const int channel, const u8 wr_vref) |
| { |
| MCHBAR32_AND_OR(GDCRCMDDEBUGMUXCFG_Cz_S(channel), ~(0x3f << 24), wr_vref << 24); |
| udelay(2); |
| } |
| |
| int aggressive_write_training(ramctr_timing *ctrl) |
| { |
| const u8 wr_vref_offsets[3] = { 0, 0x0f, 0x2f }; |
| int i, pat; |
| |
| int lower[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int upper[NUM_CHANNELS][NUM_SLOTRANKS][NUM_LANES]; |
| int channel, slotrank, lane; |
| |
| /* Changing the write Vref is only supported on some Ivy Bridge SKUs */ |
| if (!IS_IVY_CPU(ctrl->cpu)) |
| return 0; |
| |
| if (!(pci_read_config32(HOST_BRIDGE, CAPID0_A) & CAPID_WRTVREF)) |
| return 0; |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| lower[channel][slotrank][lane] = 0; |
| upper[channel][slotrank][lane] = MAX_TIMC; |
| } |
| |
| /* Only enable IOSAV_n_SPECIAL_COMMAND_ADDR optimization on later steppings */ |
| const bool enable_iosav_opt = IS_IVY_CPU_D(ctrl->cpu) || IS_IVY_CPU_E(ctrl->cpu); |
| |
| if (enable_iosav_opt) |
| MCHBAR32(MCMNTS_SPARE) = 1; |
| |
| printram("discover timC write:\n"); |
| |
| for (i = 0; i < ARRAY_SIZE(wr_vref_offsets); i++) { |
| FOR_ALL_POPULATED_CHANNELS { |
| set_write_vref(channel, wr_vref_offsets[i]); |
| |
| for (pat = 0; pat < NUM_PATTERNS; pat++) { |
| FOR_ALL_POPULATED_RANKS { |
| int timC; |
| u32 raw_stats[MAX_TIMC + 1]; |
| int stats[MAX_TIMC + 1]; |
| |
| /* Make sure rn.start < rn.end */ |
| stats[MAX_TIMC] = 1; |
| |
| fill_pattern5(ctrl, channel, pat); |
| |
| for (timC = 0; timC < MAX_TIMC; timC++) { |
| FOR_ALL_LANES { |
| ctrl->timings[channel][slotrank] |
| .lanes[lane].timC = timC; |
| } |
| program_timings(ctrl, channel); |
| |
| test_aggressive_write(ctrl, channel, slotrank); |
| |
| raw_stats[timC] = MCHBAR32( |
| IOSAV_BYTE_SERROR_C_ch(channel)); |
| } |
| FOR_ALL_LANES { |
| struct run rn; |
| for (timC = 0; timC < MAX_TIMC; timC++) { |
| stats[timC] = !!(raw_stats[timC] |
| & (1 << lane)); |
| } |
| |
| rn = get_longest_zero_run(stats, MAX_TIMC + 1); |
| if (rn.all) { |
| printk(BIOS_EMERG, |
| "timC write discovery failed: " |
| "%d, %d, %d\n", channel, |
| slotrank, lane); |
| |
| return MAKE_ERR; |
| } |
| printram("timC: %d, %d, %d: " |
| "0x%02x-0x%02x-0x%02x, " |
| "0x%02x-0x%02x\n", channel, slotrank, |
| i, rn.start, rn.middle, rn.end, |
| rn.start + ctrl->timC_offset[i], |
| rn.end - ctrl->timC_offset[i]); |
| |
| lower[channel][slotrank][lane] = |
| MAX(rn.start + ctrl->timC_offset[i], |
| lower[channel][slotrank][lane]); |
| |
| upper[channel][slotrank][lane] = |
| MIN(rn.end - ctrl->timC_offset[i], |
| upper[channel][slotrank][lane]); |
| |
| } |
| } |
| } |
| } |
| } |
| |
| FOR_ALL_CHANNELS { |
| /* Restore nominal write Vref after training */ |
| set_write_vref(channel, 0); |
| } |
| |
| /* Disable IOSAV_n_SPECIAL_COMMAND_ADDR optimization */ |
| if (enable_iosav_opt) |
| MCHBAR32(MCMNTS_SPARE) = 0; |
| |
| printram("CPB\n"); |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS FOR_ALL_LANES { |
| printram("timC %d, %d, %d: %x\n", channel, slotrank, lane, |
| (lower[channel][slotrank][lane] + |
| upper[channel][slotrank][lane]) / 2); |
| |
| ctrl->timings[channel][slotrank].lanes[lane].timC = |
| (lower[channel][slotrank][lane] + |
| upper[channel][slotrank][lane]) / 2; |
| } |
| FOR_ALL_POPULATED_CHANNELS { |
| program_timings(ctrl, channel); |
| } |
| return 0; |
| } |
| |
| void normalize_training(ramctr_timing *ctrl) |
| { |
| int channel, slotrank, lane; |
| int mat; |
| |
| FOR_ALL_CHANNELS FOR_ALL_POPULATED_RANKS { |
| int delta; |
| mat = 0; |
| FOR_ALL_LANES mat = |
| MAX(ctrl->timings[channel][slotrank].lanes[lane].timA, mat); |
| printram("normalize %d, %d, %d: mat %d\n", |
| channel, slotrank, lane, mat); |
| |
| delta = (mat >> 6) - ctrl->timings[channel][slotrank].io_latency; |
| printram("normalize %d, %d, %d: delta %d\n", |
| channel, slotrank, lane, delta); |
| |
| ctrl->timings[channel][slotrank].roundtrip_latency += delta; |
| ctrl->timings[channel][slotrank].io_latency += delta; |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| program_timings(ctrl, channel); |
| } |
| } |
| |
| int channel_test(ramctr_timing *ctrl) |
| { |
| int channel, slotrank, lane; |
| |
| slotrank = 0; |
| FOR_ALL_POPULATED_CHANNELS |
| if (MCHBAR32(MC_INIT_STATE_ch(channel)) & 0xa000) { |
| printk(BIOS_EMERG, "Mini channel test failed (1): %d\n", channel); |
| return MAKE_ERR; |
| } |
| FOR_ALL_POPULATED_CHANNELS { |
| fill_pattern0(ctrl, channel, 0x12345678, 0x98765432); |
| } |
| |
| for (slotrank = 0; slotrank < 4; slotrank++) |
| FOR_ALL_CHANNELS |
| if (ctrl->rankmap[channel] & (1 << slotrank)) { |
| FOR_ALL_LANES { |
| MCHBAR32(IOSAV_By_ERROR_COUNT(lane)) = 0; |
| MCHBAR32(IOSAV_By_BW_SERROR_C(lane)) = 0; |
| } |
| wait_for_iosav(channel); |
| |
| iosav_write_memory_test_sequence(ctrl, channel, slotrank); |
| |
| /* Execute command queue */ |
| iosav_run_once(channel); |
| |
| wait_for_iosav(channel); |
| FOR_ALL_LANES |
| if (MCHBAR32(IOSAV_By_ERROR_COUNT_ch(channel, lane))) { |
| printk(BIOS_EMERG, "Mini channel test failed (2): %d, %d, %d\n", |
| channel, slotrank, lane); |
| return MAKE_ERR; |
| } |
| } |
| return 0; |
| } |
| |
| void channel_scrub(ramctr_timing *ctrl) |
| { |
| int channel, slotrank, row, rowsize; |
| u8 bank; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| wait_for_iosav(channel); |
| fill_pattern0(ctrl, channel, 0, 0); |
| } |
| |
| /* |
| * During runtime the "scrubber" will periodically scan through the memory in the |
| * physical address space, to identify and fix CRC errors. |
| * The following loops writes to every DRAM address, setting the ECC bits to the |
| * correct value. A read from this location will no longer return a CRC error, |
| * except when a bit has toggled due to external events. |
| * The same could be achieved by writing to the physical memory map, but it's |
| * much more difficult due to SMM remapping, ME stolen memory, GFX stolen memory, |
| * and firmware running in x86_32. |
| */ |
| FOR_ALL_POPULATED_CHANNELS FOR_ALL_POPULATED_RANKS { |
| rowsize = 1 << ctrl->info.dimm[channel][slotrank >> 1].row_bits; |
| for (bank = 0; bank < 8; bank++) { |
| for (row = 0; row < rowsize; row += 16) { |
| |
| u8 gap = MAX((ctrl->tFAW >> 2) + 1, ctrl->tRRD); |
| const struct iosav_ssq sequence[] = { |
| /* |
| * DRAM command ACT |
| * Opens the row for writing. |
| */ |
| [0] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_ACT, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = gap, |
| .post_ssq_wait = ctrl->tRCD, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = row, |
| .rowbits = 6, |
| .bank = bank, |
| .rank = slotrank, |
| }, |
| .addr_update = { |
| .inc_addr_1 = 1, |
| .addr_wrap = 18, |
| }, |
| }, |
| /* |
| * DRAM command WR |
| * Writes (128 + 1) * 8 (burst length) * 8 (bus width) |
| * bytes. |
| */ |
| [1] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_WR, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 129, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = ctrl->tWTR + |
| ctrl->CWL + 8, |
| .data_direction = SSQ_WR, |
| }, |
| .sp_cmd_addr = { |
| .address = row, |
| .rowbits = 0, |
| .bank = bank, |
| .rank = slotrank, |
| }, |
| .addr_update = { |
| .inc_addr_8 = 1, |
| .addr_wrap = 9, |
| }, |
| }, |
| /* |
| * DRAM command PRE |
| * Closes the row. |
| */ |
| [2] = { |
| .sp_cmd_ctrl = { |
| .command = IOSAV_PRE, |
| .ranksel_ap = 1, |
| }, |
| .subseq_ctrl = { |
| .cmd_executions = 1, |
| .cmd_delay_gap = 4, |
| .post_ssq_wait = ctrl->tRP, |
| .data_direction = SSQ_NA, |
| }, |
| .sp_cmd_addr = { |
| .address = 0, |
| .rowbits = 6, |
| .bank = bank, |
| .rank = slotrank, |
| }, |
| .addr_update = { |
| .addr_wrap = 18, |
| }, |
| }, |
| }; |
| iosav_write_sequence(channel, sequence, ARRAY_SIZE(sequence)); |
| |
| /* Execute command queue */ |
| iosav_run_queue(channel, 16, 0); |
| |
| wait_for_iosav(channel); |
| } |
| } |
| } |
| } |
| |
| void set_scrambling_seed(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| /* FIXME: we hardcode seeds. Do we need to use some PRNG for them? I don't think so. */ |
| static u32 seeds[NUM_CHANNELS][3] = { |
| {0x00009a36, 0xbafcfdcf, 0x46d1ab68}, |
| {0x00028bfa, 0x53fe4b49, 0x19ed5483} |
| }; |
| FOR_ALL_POPULATED_CHANNELS { |
| MCHBAR32(SCHED_CBIT_ch(channel)) &= ~(1 << 28); |
| MCHBAR32(SCRAMBLING_SEED_1_ch(channel)) = seeds[channel][0]; |
| MCHBAR32(SCRAMBLING_SEED_2_HI_ch(channel)) = seeds[channel][1]; |
| MCHBAR32(SCRAMBLING_SEED_2_LO_ch(channel)) = seeds[channel][2]; |
| } |
| } |
| |
| void set_wmm_behavior(const u32 cpu) |
| { |
| if (IS_SANDY_CPU(cpu) && (IS_SANDY_CPU_D0(cpu) || IS_SANDY_CPU_D1(cpu))) { |
| MCHBAR32(SC_WDBWM) = 0x141d1519; |
| } else { |
| MCHBAR32(SC_WDBWM) = 0x551d1519; |
| } |
| } |
| |
| void prepare_training(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| /* Always drive command bus */ |
| MCHBAR32_OR(TC_RAP_ch(channel), 1 << 29); |
| } |
| |
| udelay(1); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| wait_for_iosav(channel); |
| } |
| } |
| |
| void set_read_write_timings(ramctr_timing *ctrl) |
| { |
| /* Use a larger delay when running fast to improve stability */ |
| const u32 tRWDRDD_inc = ctrl->tCK <= TCK_1066MHZ ? 4 : 2; |
| |
| int channel, slotrank; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| int min_pi = 10000; |
| int max_pi = -10000; |
| |
| FOR_ALL_POPULATED_RANKS { |
| max_pi = MAX(ctrl->timings[channel][slotrank].pi_coding, max_pi); |
| min_pi = MIN(ctrl->timings[channel][slotrank].pi_coding, min_pi); |
| } |
| |
| const u32 tWRDRDD = (max_pi - min_pi > 51) ? 0 : ctrl->ref_card_offset[channel]; |
| |
| const u32 val = (ctrl->pi_coding_threshold < max_pi - min_pi) ? 3 : 2; |
| |
| dram_odt_stretch(ctrl, channel); |
| |
| const union tc_rwp_reg tc_rwp = { |
| .tRRDR = 0, |
| .tRRDD = val, |
| .tWWDR = val, |
| .tWWDD = val, |
| .tRWDRDD = ctrl->ref_card_offset[channel] + tRWDRDD_inc, |
| .tWRDRDD = tWRDRDD, |
| .tRWSR = 2, |
| .dec_wrd = 1, |
| }; |
| MCHBAR32(TC_RWP_ch(channel)) = tc_rwp.raw; |
| } |
| } |
| |
| void set_normal_operation(ramctr_timing *ctrl) |
| { |
| int channel; |
| FOR_ALL_POPULATED_CHANNELS { |
| MCHBAR32(MC_INIT_STATE_ch(channel)) = (1 << 12) | ctrl->rankmap[channel]; |
| MCHBAR32_AND(TC_RAP_ch(channel), ~(1 << 29)); |
| } |
| } |
| |
| /* Encode the watermark latencies in a suitable format for graphics drivers consumption */ |
| static int encode_wm(int ns) |
| { |
| return (ns + 499) / 500; |
| } |
| |
| /* FIXME: values in this function should be hardware revision-dependent */ |
| void final_registers(ramctr_timing *ctrl) |
| { |
| int channel; |
| int t1_cycles = 0, t1_ns = 0, t2_ns; |
| int t3_ns; |
| u32 r32; |
| |
| /* FIXME: This register only exists on Ivy Bridge */ |
| MCHBAR32(WMM_READ_CONFIG) = 0x46; |
| |
| FOR_ALL_CHANNELS { |
| union tc_othp_reg tc_othp = { |
| .raw = MCHBAR32(TC_OTHP_ch(channel)), |
| }; |
| tc_othp.tCPDED = 1; |
| MCHBAR32(TC_OTHP_ch(channel)) = tc_othp.raw; |
| } |
| |
| /* 64 DCLKs until idle, decision per rank */ |
| MCHBAR32(PM_PDWN_CONFIG) = get_power_down_mode(ctrl) << 8 | 64; |
| |
| FOR_ALL_CHANNELS |
| MCHBAR32(PM_TRML_M_CONFIG_ch(channel)) = 0x00000aaa; |
| |
| MCHBAR32(PM_BW_LIMIT_CONFIG) = 0x5f7003ff; // OK |
| MCHBAR32(PM_DLL_CONFIG) = 0x00073000 | ctrl->mdll_wake_delay; // OK |
| |
| FOR_ALL_CHANNELS { |
| switch (ctrl->rankmap[channel]) { |
| /* Unpopulated channel */ |
| case 0: |
| MCHBAR32(PM_CMD_PWR_ch(channel)) = 0; |
| break; |
| /* Only single-ranked dimms */ |
| case 1: |
| case 4: |
| case 5: |
| MCHBAR32(PM_CMD_PWR_ch(channel)) = 0x00373131; |
| break; |
| /* Dual-ranked dimms present */ |
| default: |
| MCHBAR32(PM_CMD_PWR_ch(channel)) = 0x009b6ea1; |
| break; |
| } |
| } |
| |
| MCHBAR32(MEM_TRML_ESTIMATION_CONFIG) = 0xca9171e5; |
| MCHBAR32_AND_OR(MEM_TRML_THRESHOLDS_CONFIG, ~0x00ffffff, 0x00e4d5d0); |
| MCHBAR32_AND(MEM_TRML_INTERRUPT, ~0x1f); |
| |
| FOR_ALL_CHANNELS { |
| union tc_rfp_reg tc_rfp = { |
| .raw = MCHBAR32(TC_RFP_ch(channel)), |
| }; |
| tc_rfp.refresh_2x_control = 1; |
| MCHBAR32(TC_RFP_ch(channel)) = tc_rfp.raw; |
| } |
| |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 0); |
| MCHBAR32_OR(MC_INIT_STATE_G, 1 << 7); |
| MCHBAR32(BANDTIMERS_SNB) = 0xfa; |
| |
| /* Find a populated channel */ |
| FOR_ALL_POPULATED_CHANNELS |
| break; |
| |
| t1_cycles = (MCHBAR32(TC_ZQCAL_ch(channel)) >> 8) & 0xff; |
| r32 = MCHBAR32(PM_DLL_CONFIG); |
| if (r32 & (1 << 17)) |
| t1_cycles += (r32 & 0xfff); |
| t1_cycles += MCHBAR32(TC_SRFTP_ch(channel)) & 0xfff; |
| t1_ns = t1_cycles * ctrl->tCK / 256 + 544; |
| if (!(r32 & (1 << 17))) |
| t1_ns += 500; |
| |
| t2_ns = 10 * ((MCHBAR32(SAPMTIMERS) >> 8) & 0xfff); |
| if (MCHBAR32(SAPMCTL) & 8) { |
| t3_ns = 10 * ((MCHBAR32(BANDTIMERS_IVB) >> 8) & 0xfff); |
| t3_ns += 10 * (MCHBAR32(SAPMTIMERS2_IVB) & 0xff); |
| } else { |
| t3_ns = 500; |
| } |
| |
| /* The graphics driver will use these watermark values */ |
| printk(BIOS_DEBUG, "t123: %d, %d, %d\n", t1_ns, t2_ns, t3_ns); |
| MCHBAR32_AND_OR(SSKPD, ~0x3f3f3f3f, |
| ((encode_wm(t1_ns) + encode_wm(t2_ns)) << 16) | (encode_wm(t1_ns) << 8) | |
| ((encode_wm(t3_ns) + encode_wm(t2_ns) + encode_wm(t1_ns)) << 24) | 0x0c); |
| } |
| |
| void restore_timings(ramctr_timing *ctrl) |
| { |
| int channel; |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| const union tc_rap_reg tc_rap = { |
| .tRRD = ctrl->tRRD, |
| .tRTP = ctrl->tRTP, |
| .tCKE = ctrl->tCKE, |
| .tWTR = ctrl->tWTR, |
| .tFAW = ctrl->tFAW, |
| .tWR = ctrl->tWR, |
| .tCMD = ctrl->cmd_stretch[channel], |
| }; |
| MCHBAR32(TC_RAP_ch(channel)) = tc_rap.raw; |
| } |
| |
| udelay(1); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| wait_for_iosav(channel); |
| } |
| |
| FOR_ALL_POPULATED_CHANNELS |
| MCHBAR32_OR(TC_RWP_ch(channel), 1 << 27); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| udelay(1); |
| MCHBAR32_OR(SCHED_CBIT_ch(channel), 1 << 21); |
| } |
| |
| printram("CPE\n"); |
| |
| MCHBAR32(GDCRTRAININGMOD) = 0; |
| MCHBAR32(IOSAV_DC_MASK) = 0; |
| |
| printram("CP5b\n"); |
| |
| FOR_ALL_POPULATED_CHANNELS { |
| program_timings(ctrl, channel); |
| } |
| |
| u32 reg, addr; |
| |
| /* Poll for RCOMP */ |
| while (!(MCHBAR32(RCOMP_TIMER) & (1 << 16))) |
| ; |
| |
| do { |
| reg = MCHBAR32(IOSAV_STATUS_ch(0)); |
| } while ((reg & 0x14) == 0); |
| |
| /* Set state of memory controller */ |
| MCHBAR32(MC_INIT_STATE_G) = 0x116; |
| MCHBAR32(MC_INIT_STATE) = 0; |
| |
| /* Wait 500us */ |
| udelay(500); |
| |
| FOR_ALL_CHANNELS { |
| /* Set valid rank CKE */ |
| reg = 0; |
| reg = (reg & ~0x0f) | ctrl->rankmap[channel]; |
| addr = MC_INIT_STATE_ch(channel); |
| MCHBAR32(addr) = reg; |
| |
| /* Wait 10ns for ranks to settle */ |
| // udelay(0.01); |
| |
| reg = (reg & ~0xf0) | (ctrl->rankmap[channel] << 4); |
| MCHBAR32(addr) = reg; |
| |
| /* Write reset using a NOP */ |
| write_reset(ctrl); |
| } |
| |
| /* MRS commands */ |
| dram_mrscommands(ctrl); |
| |
| printram("CP5c\n"); |
| |
| MCHBAR32(GDCRTRAININGMOD_ch(0)) = 0; |
| |
| FOR_ALL_CHANNELS { |
| MCHBAR32_AND(GDCRCMDDEBUGMUXCFG_Cz_S(channel), ~0x3f000000); |
| udelay(2); |
| } |
| } |