| fw_config |
| field DB_CELLULAR 0 0 |
| option DB_CELLULAR_ABSENT 0 |
| option DB_CELLULAR_PCIE 1 |
| end |
| field KB_COLOR 1 1 |
| option KB_COLOR_WHITE 0 |
| option KB_COLOR_BLUE 1 |
| end |
| field NAND 2 2 |
| option NAND_MICRON 0 |
| option NAND_KIOXIA 1 |
| end |
| field WIFI_SAR_ID 30 31 |
| option WIFI_SAR_ID_0 0 |
| option WIFI_SAR_ID_1 1 |
| end |
| end |
| chip soc/intel/alderlake |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C2 | | |
| #| I2C3 | Touchscreen | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 45, |
| .scl_hcnt = 33, |
| .sda_hold = 20, |
| }, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 600, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[3] = { |
| .rise_time_ns = 650, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[7] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 45, |
| .scl_hcnt = 30, |
| .sda_hold = 20, |
| }, |
| }, |
| }" |
| register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC3)" # USB2_C3 |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" |
| register "usb2_ports[8]" = "USB2_PORT_EMPTY" |
| |
| register "usb3_ports[0]" = "USB3_PORT_EMPTY" |
| |
| register "tcss_ports[3]" = "TCSS_PORT_DEFAULT(OC3)" |
| register "sagv" = "SaGv_Enabled" |
| |
| # As per Intel Advisory doc#723158, the change is required to prevent possible |
| # display flickering issue. |
| register "usb2_phy_sus_pg_disable" = "1" |
| |
| # Set EPP to 50%: 50 * 256 / 100 = 0x80 |
| register "enable_energy_perf_pref" = "true" |
| register "energy_perf_pref_value" = "0x80" |
| |
| # FIVR RFI Spread Spectrum 6% |
| register "fivr_spread_spectrum" = "FIVR_SS_6" |
| |
| # I2C Port Config |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| [PchSerialIoIndexI2C7] = PchSerialIoPci, |
| }" |
| device domain 0 on |
| device ref igpu on |
| chip drivers/gfx/generic |
| register "device_count" = "5" |
| # DDIA for eDP |
| register "device[0].name" = ""LCD0"" |
| # Internal panel on the first port of the graphics chip |
| register "device[0].addr" = "0x80010400" |
| # DDIB is unused and HDMI is not enumerated in the kernel, so no GFX device is added for DDIB |
| # TCP0 (DP-1) for port C0 |
| register "device[1].name" = ""DD01"" |
| register "device[1].use_pld" = "true" |
| register "device[1].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| # TCP1 (DP-2) for port C1 |
| register "device[2].name" = ""DD02"" |
| register "device[2].use_pld" = "true" |
| register "device[2].pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| # TCP2 (DP-3) for port C2 |
| register "device[3].name" = ""DD03"" |
| register "device[3].use_pld" = "true" |
| register "device[3].pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| # TCP3 (DP-4) for port C3 |
| register "device[4].name" = ""DD04"" |
| register "device[4].use_pld" = "true" |
| register "device[4].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))" |
| device generic 0 on end |
| end |
| end # Integrated Graphics Device |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DRAM"" |
| register "options.tsr[1].desc" = ""Soc"" |
| register "options.tsr[2].desc" = ""Charger"" |
| register "options.tsr[3].desc" = ""Regulator"" |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 5000), |
| }" |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), |
| }" |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 15000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 55000, |
| .max_power = 55000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| device generic 0 on end |
| end |
| end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "1" |
| device generic 0 on end |
| end |
| end |
| device ref pcie4_0 on |
| # Enable CPU PCIE RP 1 using CLK 1 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 1, |
| .clk_src = 1, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end |
| device ref tbt_pcie_rp3 on end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp6 on |
| # Enable WWAN PCIE 6 using clk 5 |
| register "pch_pcie_rp[PCH_RP(6)]" = "{ |
| .clk_src = 5, |
| .clk_req = 5, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip soc/intel/common/block/pcie/rtd3 |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" |
| register "reset_off_delay_ms" = "20" |
| register "srcclk_pin" = "5" |
| register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL" |
| register "skip_on_off_support" = "true" |
| register "use_rp_mutex" = "true" |
| device generic 0 alias rp6_rtd3 on end |
| end |
| chip drivers/wwan/fm |
| register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F21)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E16)" |
| register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" |
| register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A7)" |
| register "add_acpi_dma_property" = "true" |
| use rp6_rtd3 as rtd3dev |
| device generic 0 alias rp6_wwan on end |
| end |
| end |
| device ref pcie_rp8 off end |
| device ref pcie_rp9 off end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port1 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port3 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK0"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Tweeter Left Audio Codec"" |
| register "uid" = "2" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x40 alias i2c0_cs35l53_0 on end |
| end |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK1"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Woofer Left Audio Codec"" |
| register "uid" = "0" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x41 alias i2c0_cs35l53_1 on end |
| end |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK2"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Tweeter Right Audio Codec"" |
| register "uid" = "3" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x42 on end |
| end |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK3"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Woofer Right Audio Codec"" |
| register "uid" = "1" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x43 on end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2513"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "200" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x10 on end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| register "has_power_resource" = "1" |
| |
| register "ssdb.lanes_used" = "4" |
| register "ssdb.link_used" = "1" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "360000000" |
| register "link_freq[1]" = "180000000" |
| register "remote_name" = ""IPU0"" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_2" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_F20" #reset |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_C4" #power |
| |
| #_ON |
| register "on_seq.ops_cnt" = "4" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "3" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "nvm_compat" = ""atmel,24c1024"" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "0x01" |
| register "nvm_readonly" = "0x01" |
| register "nvm_width" = "0x10" |
| |
| device i2c 50 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2703"" |
| register "generic.desc" = ""ELAN Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device ref i2c7 on |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK0"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Tweeter Left Audio Codec"" |
| register "uid" = "2" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x40 alias i2c7_cs35l53_0 on end |
| end |
| chip drivers/i2c/cs35l53 |
| register "name" = ""SPK1"" |
| register "sub" = ""103C8C08"" |
| register "desc" = ""Cirrus Logic CS35L53 Woofer Left Audio Codec"" |
| register "uid" = "0" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "boost_type" = "EXTERNAL_BOOST" |
| register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED" |
| register "gpio1_output_enable" = "true" |
| register "gpio1_src_select" = "GPIO1_SRC_GPIO" |
| register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE" |
| device i2c 0x41 alias i2c7_cs35l53_1 on end |
| end |
| end |
| device ref gspi1 on |
| chip drivers/spi/acpi |
| register "name" = ""CRFP"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "uid" = "1" |
| register "compat_string" = ""google,cros-ec-spi"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)" |
| register "enable_delay_ms" = "3" |
| device spi 0 hidden end |
| end # FPMCU |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| use conn2 as mux_conn[2] |
| use conn3 as mux_conn[3] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 2 alias conn2 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port5 as usb2_port |
| use tcss_usb3_port4 as usb3_port |
| device generic 3 alias conn3 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (MlB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C3 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))" |
| device ref tcss_usb3_port4 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C3 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""RGB Keyboard"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end |
| end |
| end |