| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | Digitizer | |
| #| I2C2 | Touchscreen, Stylus | |
| #| I2C4 | Audio | |
| #| I2C5 | P-Sensor | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| # USB Port Configuration |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Not Used |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # UF Camera |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WF Camera |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| # Enable Acoustic noise mitigation and set slew rate to 1/8 |
| # Rest of the parameters are 0 by default. |
| register "AcousticNoiseMitigation" = "1" |
| register "SlowSlewRate" = "SlewRateFastBy8" |
| register "FastPkgCRampDisable" = "1" |
| |
| # Set xHCI LFPS period sampling off time to 0 ms |
| register "xhci_lfps_sampling_offtime_ms" = "0" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 90, 10000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 80, 60000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 15000) |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN) |
| }" |
| |
| ## Power Limits Control |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 6000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 24, 2000 }, |
| [2] = { 16, 1500 }, |
| [3] = { 8, 1000 } |
| }" |
| |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)" |
| register "reset_off_delay_ms" = "10" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" |
| register "enable_delay_ms" = "20" |
| device usb 2.3 alias usb2_lte on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""UFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.3 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0000"" |
| register "generic.cid" = ""ACPI0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| end # I2C 0 |
| device pci 15.2 on |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_C12)" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "180" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "20" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x5d on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN901C"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end # I2C 2 |
| device pci 15.3 off end # I2C 3 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "0" |
| device i2c 28 on |
| probe AUDIO_AMP RT1015_I2C |
| probe AUDIO_AMP UNPROVISIONED |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on |
| probe AUDIO_AMP RT1015_I2C |
| probe AUDIO_AMP UNPROVISIONED |
| end |
| end |
| end # I2C 4 |
| device pci 19.1 on |
| chip drivers/i2c/sx9324 |
| register "desc" = ""SAR Proximity Sensor"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E11_IRQ)" |
| register "uid" = "2" |
| register "reg_gnrl_ctrl0" = "0x0a" |
| register "reg_gnrl_ctrl1" = "0x22" |
| register "reg_afe_ctrl0" = "0x20" |
| register "reg_afe_ctrl3" = "0x01" |
| register "reg_afe_ctrl4" = "0x47" |
| register "reg_afe_ctrl6" = "0x00" |
| register "reg_afe_ctrl7" = "0x47" |
| register "reg_afe_ctrl8" = "0x12" |
| register "reg_afe_ctrl9" = "0x0f" |
| register "reg_afe_ph0" = "0x37" |
| register "reg_afe_ph1" = "0x29" |
| register "reg_afe_ph2" = "0x1f" |
| register "reg_afe_ph3" = "0x3d" |
| register "reg_prox_ctrl0" = "0x0b" |
| register "reg_prox_ctrl1" = "0x0b" |
| register "reg_prox_ctrl2" = "0x20" |
| register "reg_prox_ctrl3" = "0x20" |
| register "reg_prox_ctrl4" = "0x0c" |
| register "reg_prox_ctrl5" = "0x00" |
| register "reg_prox_ctrl6" = "0x2d" |
| register "reg_prox_ctrl7" = "0xc0" |
| register "reg_adv_ctrl0" = "0x00" |
| register "reg_adv_ctrl1" = "0x00" |
| register "reg_adv_ctrl2" = "0x00" |
| register "reg_adv_ctrl3" = "0x00" |
| register "reg_adv_ctrl4" = "0x00" |
| register "reg_adv_ctrl5" = "0x05" |
| register "reg_adv_ctrl6" = "0x00" |
| register "reg_adv_ctrl7" = "0x00" |
| register "reg_adv_ctrl8" = "0x00" |
| register "reg_adv_ctrl9" = "0x00" |
| register "reg_adv_ctrl10" = "0x00" |
| register "reg_adv_ctrl11" = "0x00" |
| register "reg_adv_ctrl12" = "0x00" |
| register "reg_adv_ctrl13" = "0x00" |
| register "reg_adv_ctrl14" = "0x80" |
| register "reg_adv_ctrl15" = "0x0c" |
| register "reg_adv_ctrl16" = "0x04" |
| register "reg_adv_ctrl17" = "0x70" |
| register "reg_adv_ctrl18" = "0x40" |
| register "reg_adv_ctrl19" = "0x00" |
| register "reg_adv_ctrl20" = "0x00" |
| register "reg_irq_msk" = "0x6f" |
| register "reg_irq_cfg0" = "0x00" |
| register "reg_irq_cfg1" = "0x80" |
| register "reg_irq_cfg2" = "0x00" |
| device i2c 28 on end |
| end |
| end # I2C 5 |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on |
| probe AUDIO_AMP RT1015P_AUTO |
| end |
| end |
| end # Intel HDA |
| end |
| end |