| chip soc/intel/apollolake |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-16.32. |
| # [14:8] steps of delay for DDR mode, each 125ps. |
| # [6:0] steps of delay for SDR mode, each 125ps. |
| register "emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-16.33. |
| # [14:8] steps of delay for HS400, each 125ps. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps. |
| register "emmc_tx_data_cntl1" = "0x0b0c" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-16.34. |
| # [30:24] steps of delay for SDR50, each 125ps. |
| # [22:16] steps of delay for DDR50, each 125ps. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps. |
| # [6:0] steps of delay for SDR12, each 125ps. |
| register "emmc_tx_data_cntl2" = "0x1c282929" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-16.35. |
| # [30:24] steps of delay for SDR50, each 125ps. |
| # [22:16] steps of delay for DDR50, each 125ps. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps. |
| # [6:0] steps of delay for SDR12, each 125ps. |
| register "emmc_rx_cmd_data_cntl1" = "0x00181b1b" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-16.37. |
| # [17:16] stands for Rx Clock before Output Buffer |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps. |
| # [6:0] steps of delay for HS200, each 125ps. |
| register "emmc_rx_cmd_data_cntl2" = "0x10028" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-16.36. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps. |
| register "emmc_rx_strobe_cntl" = "0x0b0b" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Digitizer | |
| #| I2C5 | Audio | |
| #| I2C6 | Trackpad | |
| #| I2C7 | Touchscreen | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 66, |
| .fall_time_ns = 90, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 104, |
| .fall_time_ns = 52, |
| }, |
| .i2c[6] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 66, |
| .fall_time_ns = 90, |
| .data_hold_time_ns = 350, |
| }, |
| .i2c[7] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 76, |
| .fall_time_ns = 164, |
| }, |
| }" |
| |
| device domain 0 on |
| device pci 16.0 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""WCOM50C1"" |
| register "generic.desc" = ""WCOM Digitizer"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_139_IRQ)" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x1" |
| device i2c 0x9 on end |
| end |
| end # - I2C 0 |
| device pci 17.1 on |
| chip drivers/i2c/da7219 |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on end |
| end |
| end # - I2C 5 |
| device pci 17.2 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)" |
| register "wake" = "GPE0_DW3_27" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)" |
| register "generic.wake" = "GPE0_DW3_27" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| end # - I2C 6 |
| device pci 17.3 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN90FC"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYTS7817"" |
| register "generic.desc" = ""Synaptics Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)" |
| register "generic.reset_delay_ms" = "45" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 20 on end |
| end |
| end # - I2C 7 |
| end |
| |
| # Disable xHCI compliance mode |
| register "DisableComplianceMode" = "1" |
| end |