| chip soc/intel/apollolake |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-16.32. |
| # [14:8] steps of delay for DDR mode, each 125ps. |
| # [6:0] steps of delay for SDR mode, each 125ps. |
| register "emmc_tx_cmd_cntl" = "0x00000505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-16.33. |
| # [14:8] steps of delay for HS400, each 125ps. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps. |
| register "emmc_tx_data_cntl1" = "0x00000c0d" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-16.34. |
| # [30:24] steps of delay for SDR50, each 125ps. |
| # [22:16] steps of delay for DDR50, each 125ps. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps. |
| # [6:0] steps of delay for SDR12, each 125ps. |
| register "emmc_tx_data_cntl2" = "0x1c2a2a2a" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-16.35. |
| # [30:24] steps of delay for SDR50, each 125ps. |
| # [22:16] steps of delay for DDR50, each 125ps. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps. |
| # [6:0] steps of delay for SDR12, each 125ps. |
| register "emmc_rx_cmd_data_cntl1" = "0x00181b1b" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-16.37. |
| # [17:16] stands for Rx Clock before Output Buffer |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps. |
| # [6:0] steps of delay for HS200, each 125ps. |
| register "emmc_rx_cmd_data_cntl2" = "0x0001000f" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-16.36. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps. |
| register "emmc_rx_strobe_cntl" = "0x00000a0a" |
| |
| # Override USB2 PER PORT register (PORT 4) |
| register "usb2eye[4]" = "{ |
| .Usb20OverrideEn = 1, |
| .Usb20PerPortPeTxiSet = 7, |
| .Usb20PerPortTxiSet = 3, |
| .Usb20IUsbTxEmphasisEn = 3, |
| .Usb20PerPortTxPeHalf = 0, |
| }" |
| |
| # Override USB2 PER PORT register (PORT 6) |
| register "usb2eye[6]" = "{ |
| .Usb20OverrideEn = 1, |
| .Usb20PerPortPeTxiSet = 3, |
| .Usb20PerPortTxiSet = 0, |
| .Usb20IUsbTxEmphasisEn = 3, |
| .Usb20PerPortTxPeHalf = 0, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C5 | Audio | |
| #| I2C6 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[6] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 66, |
| .fall_time_ns = 90, |
| .data_hold_time_ns = 350, |
| }, |
| }" |
| |
| device domain 0 on |
| device pci 15.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| device usb 2.3 off end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| device usb 3.3 off end |
| end |
| end |
| end |
| end # - XHCI |
| device pci 17.1 on |
| chip drivers/i2c/da7219 |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on end |
| end |
| end # - I2C 5 |
| device pci 17.2 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)" |
| register "wake" = "GPE0_DW3_27" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ZNT0000"" |
| register "generic.desc" = ""Zinitix Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)" |
| register "generic.wake" = "GPE0_DW3_27" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0xE" |
| device i2c 40 on end |
| end |
| end # - I2C 6 |
| end |
| |
| # Disable compliance mode |
| register "DisableComplianceMode" = "1" |
| end |