| chip soc/intel/cannonlake |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 15, |
| .tdp_pl2_override = 51, |
| }" |
| |
| register "SerialIoDevMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| [PchSerialIoIndexSPI0] = PchSerialIoPci, |
| [PchSerialIoIndexSPI1] = PchSerialIoPci, |
| [PchSerialIoIndexSPI2] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART0] = PchSerialIoSkipInit, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoDisabled, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Touchpad | |
| #| I2C1 | Touch screen | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 50, |
| .fall_time_ns = 15, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 60, |
| .fall_time_ns = 25, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 60, |
| .fall_time_ns = 60, |
| }, |
| }" |
| |
| # GPIO for SD card detect |
| register "sdcard_cd_gpio" = "vSD3_CD_B" |
| |
| # Enable eMMC HS400 |
| register "ScsEmmcHs400Enabled" = "1" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-14.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-14.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-14.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-14.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-14.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-14.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515" |
| |
| device domain 0 on |
| device pci 02.0 on # Integrated Graphics Device |
| register "gfx" = "GMA_DEFAULT_PANEL(0)" |
| end |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_A21_IRQ)" |
| register "wake" = "GPE0_DW0_21" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_A21_IRQ)" |
| register "generic.wake" = "GPE0_DW0_21" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| end # I2C #0 |
| device pci 15.1 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "reset_delay_ms" = "100" |
| register "reset_off_delay_ms" = "5" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)" |
| register "enable_delay_ms" = "10" |
| register "enable_off_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 49 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RAYD0001"" |
| register "desc" = ""Raydium Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "reset_delay_ms" = "1" |
| register "reset_off_delay_ms" = "2" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)" |
| register "enable_delay_ms" = "10" |
| register "enable_off_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 39 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9004"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D16_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)" |
| register "generic.enable_delay_ms" = "10" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C4)" |
| register "generic.stop_delay_ms" = "300" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A8)" |
| register "key.wake_gpe" = "GPE0_DW0_08" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_ASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| end # I2C #1 |
| device pci 15.2 off end # I2C #2 unused |
| device pci 15.3 off end # I2C #3 unused |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" |
| register "property_count" = "1" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| end #I2C #4 |
| device pci 1a.0 on end # eMMC |
| device pci 1e.3 off end # GSPI #1 unused |
| device pci 1f.3 on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98357A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H3)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| end |
| |
| end |