| chip soc/intel/jasperlake |
| # Disable PCIe Root Port 8 (index 7) |
| register "PcieRpEnable[7]" = "0" |
| # Disable PCIe Clock Source 4 (index 3) |
| register "PcieClkSrcUsage[3]" = "0xff" |
| |
| # USB Port Configuration |
| register "usb2_ports[0]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Type-C Port C0 |
| register "usb2_ports[1]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_16P9MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_39P35MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Type-C Port C1 |
| register "usb2_ports[2]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_16P9MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_39P35MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Type-A Port A0 |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_11P25MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Type-A Port A1 |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Camera |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | Digitizer | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | Camera | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 209, |
| .fall_time_ns = 12, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 175, |
| .fall_time_ns = 8, |
| }, |
| }" |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| register "options.tsr[0].desc" = ""Charger"" |
| register "options.tsr[1].desc" = ""Vcore"" |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 90, 10000), |
| [1] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_0, 60, 60000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 60, 15000), |
| }" |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN), |
| }" |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 6000, |
| .max_power = 6000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 39, 2500 }, |
| [2] = { 31, 2000 }, |
| [3] = { 23, 1500 } |
| }" |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""UFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D13)" |
| register "enable_delay_ms" = "20" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)" |
| register "reset_off_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" |
| register "enable_delay_ms" = "20" |
| device usb 3.3 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ZNT0000"" |
| register "generic.desc" = ""Zinitix Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0xE" |
| device i2c 40 on end |
| end |
| end # I2C 0 |
| device pci 15.2 on end |
| device pci 1c.7 off end # PCI Express Root Port 8 |
| device pci 19.0 on |
| chip drivers/i2c/da7219 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on end |
| end |
| end #I2C 4 |
| device pci 1f.3 on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| end |
| end |