| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 247, |
| .fall_time_ns = 11, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 175, |
| .fall_time_ns = 20, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 99, |
| .fall_time_ns = 7, |
| }, |
| }" |
| |
| # USB Port Configuration |
| register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Not Used |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Not Used |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # UF Camera |
| register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Not Used |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| }" |
| |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "tcc_offset" = "10" # TCC of 95C |
| |
| # Enable Acoustic noise mitigation and set slew rate to 1/8 |
| # Rest of the parameters are 0 by default. |
| register "AcousticNoiseMitigation" = "1" |
| register "SlowSlewRate" = "SlewRateFastBy8" |
| register "FastPkgCRampDisable" = "1" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 60, 50000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 50, 50000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 50, 50000),}" |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 110, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 88, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 88, SHUTDOWN),}" |
| register "controls.power_limits.pl1" = "{ |
| .min_power = 4300, |
| .max_power = 6000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 250,}" |
| register "controls.power_limits.pl2" = "{ |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}" |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""UFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| end # I2C 0 |
| device pci 15.1 off end # I2C 1 |
| device pci 15.2 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7503"" |
| register "generic.desc" = ""G2 Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "120" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x40 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "reset_delay_ms" = "20" |
| register "reset_off_delay_ms" = "2" |
| register "stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "stop_delay_ms" = "280" |
| register "stop_off_delay_ms" = "2" |
| register "enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on end |
| end |
| end # I2C 2 |
| device pci 15.3 off end # I2C 3 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| end # I2C 4 |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| end |
| end |