| fw_config |
| field DB_SD 0 1 |
| option SD_ABSENT 0 |
| option SD_GL9755S 1 |
| end |
| field KB_BL 2 2 |
| option KB_BL_ABSENT 0 |
| option KB_BL_PRESENT 1 |
| end |
| field AUDIO 3 5 |
| option AUDIO_UNKNOWN 0 |
| option MAX98390_ALC5682I_I2S_4SPK 1 |
| end |
| field DB_LTE 6 7 |
| option LTE_ABSENT 0 |
| option LTE_USB 1 |
| option LTE_PCIE 2 |
| end |
| field EPS 10 10 |
| option PRIVACY_SCREEN_ABSENT 0 |
| option PRIVACY_SCREEN 1 |
| end |
| field CAMERA_UFC 38 39 |
| option CAMERA_NONE 0 |
| option CAMERA_OV5675 1 |
| option CAMERA_HI556 2 |
| end |
| field TP_SOURCE 40 41 |
| option ELAN0000 0 |
| option ELAN2703 1 |
| end |
| end |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| register "cnvi_bt_audio_offload" = "true" |
| # FIVR RFI Spread Spectrum 6% |
| register "fivr_spread_spectrum" = "FIVR_SS_6" |
| |
| # Acoustic settings |
| register "acoustic_noise_mitigation" = "1" |
| register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8" |
| register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" |
| |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" |
| register "usb2_ports[5]" = "USB2_PORT_EMPTY" |
| register "tcss_ports[1]" = "TCSS_PORT_EMPTY" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | Audio | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | | |
| #| I2C3 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| register "tcc_offset" = "3" # TCC of 97C |
| |
| device domain 0 on |
| device ref igpu on |
| chip drivers/gfx/generic |
| register "device_count" = "1" |
| register "device[0].name" = ""LCD"" |
| # Use ChromeOS privacy screen _HID |
| register "device[0].hid" = ""GOOG0010"" |
| # Internal panel on the first port of the graphics chip |
| register "device[0].addr" = "0x80010400" |
| register "device[0].privacy.enabled" = "1" |
| register "device[0].privacy.gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H21)" |
| device generic 0 on |
| probe EPS PRIVACY_SCREEN |
| end |
| end |
| end # Integrated Graphics Device |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DRAM"" |
| register "options.tsr[1].desc" = ""SOC"" |
| register "options.tsr[2].desc" = ""Charger"" |
| register "options.tsr[3].desc" = ""5V regulator"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 55, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 45, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 51, 5000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 51, 5000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 51, 5000), |
| }" |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 13000, |
| .max_power = 15000, |
| .time_window_min = 42 * MSECS_PER_SEC, |
| .time_window_max = 42 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 35000, |
| .max_power = 35000, |
| .time_window_min = 42 * MSECS_PER_SEC, |
| .time_window_max = 42 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref tbt_pcie_rp1 off end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "2" |
| device generic 0 on end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp6 on |
| # Enable WWAN PCIE 6 using clk 5 |
| register "pch_pcie_rp[PCH_RP(6)]" = "{ |
| .clk_src = 5, |
| .clk_req = 5, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip soc/intel/common/block/pcie/rtd3 |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" |
| register "reset_off_delay_ms" = "20" |
| # register "reset_delay_ms" = "1000" |
| register "srcclk_pin" = "5" |
| register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL" |
| register "skip_on_off_support" = "true" |
| device generic 0 alias rp6_rtd3 on |
| probe DB_LTE LTE_PCIE |
| end |
| end |
| chip drivers/wwan/fm |
| register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F21)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E16)" |
| register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" |
| register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A7)" |
| register "add_acpi_dma_property" = "true" |
| use rp6_rtd3 as rtd3dev |
| device generic 0 on |
| probe DB_LTE LTE_PCIE |
| end |
| end |
| probe DB_LTE LTE_PCIE |
| end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port1 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port3 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp8 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end #PCIE8 SD card |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO MAX98390_ALC5682I_I2S_4SPK |
| end |
| end |
| chip drivers/i2c/max98390 |
| register "desc" = ""MAX98390 Speaker Amp 0"" |
| register "uid" = "0" |
| register "name" = ""MXW0"" |
| register "r0_calib_key" = ""dsm_calib_r0_0"" |
| register "temperature_calib_key" = ""dsm_calib_temp_0"" |
| register "dsm_param_file_name" = ""dsm_param_R"" |
| register "vmon_slot_no" = "0" |
| register "imon_slot_no" = "1" |
| device i2c 0x3a on |
| probe AUDIO MAX98390_ALC5682I_I2S_4SPK |
| end |
| end |
| chip drivers/i2c/max98390 |
| register "desc" = ""MAX98390 Speaker Amp 1"" |
| register "uid" = "1" |
| register "name" = ""MXW1"" |
| register "r0_calib_key" = ""dsm_calib_r0_1"" |
| register "temperature_calib_key" = ""dsm_calib_temp_1"" |
| register "dsm_param_file_name" = ""dsm_param_L"" |
| register "vmon_slot_no" = "1" |
| register "imon_slot_no" = "0" |
| device i2c 0x3b on |
| probe AUDIO MAX98390_ALC5682I_I2S_4SPK |
| end |
| end |
| chip drivers/i2c/max98390 |
| register "desc" = ""MAX98390 Speaker Amp 2"" |
| register "uid" = "2" |
| register "name" = ""MXW2"" |
| register "r0_calib_key" = ""dsm_calib_r0_2"" |
| register "temperature_calib_key" = ""dsm_calib_temp_2"" |
| register "dsm_param_file_name" = ""dsm_param_tt_R"" |
| register "vmon_slot_no" = "2" |
| register "imon_slot_no" = "3" |
| device i2c 0x38 on |
| probe AUDIO MAX98390_ALC5682I_I2S_4SPK |
| end |
| end |
| chip drivers/i2c/max98390 |
| register "desc" = ""MAX98390 Speaker Amp 3"" |
| register "uid" = "3" |
| register "name" = ""MXW3"" |
| register "r0_calib_key" = ""dsm_calib_r0_3"" |
| register "temperature_calib_key" = ""dsm_calib_temp_3"" |
| register "dsm_param_file_name" = ""dsm_param_tt_L"" |
| register "vmon_slot_no" = "3" |
| register "imon_slot_no" = "2" |
| device i2c 0x39 on |
| probe AUDIO MAX98390_ALC5682I_I2S_4SPK |
| end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2513"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "300" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x15 on end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #EN_UCAM_LED_PWR |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #EN_UCAM_PWR |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| device i2c 36 on |
| probe CAMERA_UFC CAMERA_NONE |
| probe CAMERA_UFC CAMERA_OV5675 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""INT3537"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Hi-556 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "437000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #EN_UCAM_LED_PWR |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #EN_UCAM_PWR |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| device i2c 20 on |
| probe CAMERA_UFC CAMERA_HI556 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""M24C64X"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_UCAM_PWR |
| |
| #_ON |
| register "on_seq.ops_cnt" = "1" |
| register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "1" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c64"" |
| device i2c 50 on end |
| end |
| |
| end |
| device ref i2c3 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on |
| probe TP_SOURCE ELAN0000 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2703"" |
| register "generic.desc" = ""ELAN Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on |
| probe TP_SOURCE ELAN2703 |
| end |
| end |
| end |
| device ref gspi1 on |
| chip drivers/spi/acpi |
| register "name" = ""CRFP"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "uid" = "1" |
| register "compat_string" = ""google,cros-ec-spi"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| device spi 0 on end |
| end # FPMCU |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end |
| end |
| end |