| # SPDX-License-Identifier: GPL-2.0-only |
| |
| if BOARD_AMD_BILBY |
| |
| config BOARD_SPECIFIC_OPTIONS |
| def_bool y |
| select SOC_AMD_COMMON_BLOCK_USE_ESPI |
| select SOC_AMD_PICASSO |
| select BOARD_ROMSIZE_KB_16384 |
| select AZALIA_PLUGIN_SUPPORT |
| select HAVE_ACPI_RESUME |
| select DRIVERS_UART_ACPI |
| select AMD_SOC_CONSOLE_UART if !AMD_LPC_DEBUG_CARD |
| |
| config FMDFILE |
| string |
| default "src/mainboard/amd/bilby/board.fmd" |
| |
| config AMD_LPC_DEBUG_CARD |
| bool "Enable LPC-Serial debug card on the debug header" |
| default n |
| select BILBY_LPC |
| select SUPERIO_SMSC_SIO1036 |
| help |
| AMD's debug card contains an SMSC SIO1036 device which provides an |
| I/O-mapped UART in the system. This is mutually exclusive with |
| AMD_SOC_CONSOLE_UART which selects the SoC's integrated memory-mapped |
| UART for coreboot console output. |
| |
| choice |
| prompt "SMSC/Microchip 1036 SuperIO config address" |
| depends on SUPERIO_SMSC_SIO1036 |
| default BILBY_SMSC_SIO1036_BASE_164E |
| |
| config BILBY_SMSC_SIO1036_BASE_4E |
| bool "0x4e/0x4d base address" |
| |
| config BILBY_SMSC_SIO1036_BASE_164E |
| bool "0x164e/0x164d base address" |
| |
| endchoice |
| |
| config SUPERIO_ADDR_BASE |
| hex |
| default 0x4e if BILBY_SMSC_SIO1036_BASE_4E |
| default 0x164e if BILBY_SMSC_SIO1036_BASE_164E |
| |
| config CBFS_SIZE |
| hex |
| default 0xfcf000 # Maximum size for the Bilby FMAP |
| |
| config MAINBOARD_DIR |
| string |
| default "amd/bilby" |
| |
| config MAINBOARD_PART_NUMBER |
| string |
| default "BILBY" |
| |
| config DEVICETREE |
| string |
| default "devicetree.cb" |
| |
| config ONBOARD_VGA_IS_PRIMARY |
| bool |
| default y |
| |
| config AMD_FWM_POSITION_INDEX |
| int |
| default 4 |
| help |
| TODO: might need to be adapted for better placement of files in cbfs |
| |
| config MANDOLIN_HAVE_MCHP_FW |
| bool "Have Microchip EC firmware?" |
| default n |
| |
| config MANDOLIN_MCHP_FW_FILE |
| string |
| depends on MANDOLIN_HAVE_MCHP_FW |
| default "3rdparty/blobs/mainboard/amd/mandolin/EC_mandolin.bin" if BOARD_AMD_MANDOLIN |
| default "3rdparty/blobs/mainboard/amd/mandolin/EC_cereme.bin" if BOARD_AMD_BILBY |
| help |
| The EC firmware blob is usually the first 128kByte of the stock |
| firmware image. |
| if !AMD_LPC_DEBUG_CARD |
| choice |
| prompt "State of IOMux for LPC/eMMC signals" |
| default BILBY_IOMUX_USE_EMMC |
| help |
| Bilby is designed to use either LPC or eMMC signals. Use this |
| selection to determine which are configured for this image. |
| |
| config BILBY_IOMUX_USE_LPC |
| bool "LPC signals" |
| |
| config BILBY_IOMUX_USE_EMMC |
| bool "eMMC signals" |
| |
| endchoice |
| endif # !AMD_LPC_DEBUG_CARD |
| |
| config BILBY_LPC |
| bool |
| default y if BILBY_IOMUX_USE_LPC |
| help |
| Picasso's LPC bus signals are MUXed with some of the EMMC signals. |
| Select this option if LPC signals are required. |
| |
| #TODO: remove this hack to not break graphics in combination with SeaBIOS |
| config VGA_BIOS_DGPU_ID |
| string |
| default "1002,15d8" |
| help |
| The default VGA BIOS PCI vendor/device ID should be set to the |
| result of the map_oprom_vendev() function in northbridge.c. |
| |
| config VGA_BIOS_DGPU_FILE |
| string |
| default "3rdparty/amd_blobs/picasso/Raven2GenericVbios.bin" |
| |
| config EFS_SPI_READ_MODE |
| int |
| default 0 if EM100 |
| default 3 |
| |
| config EFS_SPI_SPEED |
| int |
| default 3 if EM100 |
| default 0 |
| |
| config EFS_SPI_MICRON_FLAG |
| int |
| default 0 |
| |
| endif # BOARD_AMD_BILBY |