| ## SPDX-License-Identifier: GPL-2.0-only |
| |
| chip soc/intel/skylake |
| |
| register "deep_sx_config" = "DSX_EN_WAKE_PIN" |
| |
| register "eist_enable" = "1" |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "GPP_B" |
| register "gpe0_dw1" = "GPP_D" |
| register "gpe0_dw2" = "GPP_E" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # FSP Configuration |
| register "PrimaryDisplay" = "Display_PEG" |
| |
| # Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch |
| # SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s |
| register "PmConfigSlpS3MinAssert" = "0x02" |
| |
| # SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s |
| register "PmConfigSlpS4MinAssert" = "0x04" |
| |
| # SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s |
| register "PmConfigSlpSusMinAssert" = "0x03" |
| |
| # SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s |
| register "PmConfigSlpAMinAssert" = "0x03" |
| |
| # PL2 override 91W |
| register "power_limits_config" = "{ |
| .tdp_pl2_override = 91, |
| }" |
| |
| # Send an extra VR mailbox command for the PS4 exit issue |
| register "SendVrMbxCmd" = "2" |
| |
| device cpu_cluster 0 on end |
| device domain 0 on |
| device ref system_agent on |
| subsystemid 0x1849 0x191f |
| end |
| device ref peg0 on |
| subsystemid 0x1849 0x1901 |
| register "Peg0MaxLinkWidth" = "Peg0_x16" |
| |
| # Configure PCIe clockgen in PCH |
| register "PcieRpClkReqSupport[0]" = "1" |
| register "PcieRpClkReqNumber[0]" = "0" |
| register "PcieRpClkSrcNumber[0]" = "0" |
| end |
| device ref igpu on |
| subsystemid 0x1849 0x1912 |
| end |
| device ref sa_thermal on end |
| device ref south_xhci on |
| subsystemid 0x1849 0xa131 |
| |
| register "usb2_ports" = "{ |
| [0] = USB2_PORT_MID(OC0), |
| [1] = USB2_PORT_MID(OC0), |
| [2] = USB2_PORT_MID(OC4), |
| [3] = USB2_PORT_MID(OC4), |
| [4] = USB2_PORT_MID(OC2), |
| [5] = USB2_PORT_MID(OC2), |
| [6] = USB2_PORT_MID(OC0), |
| [7] = USB2_PORT_MID(OC0), |
| [8] = USB2_PORT_MID(OC0), |
| [9] = USB2_PORT_MID(OC0), |
| [10] = USB2_PORT_MID(OC1), |
| [11] = USB2_PORT_MID(OC1), |
| [12] = USB2_PORT_MID(OC_SKIP), |
| [13] = USB2_PORT_MID(OC_SKIP), |
| }" |
| register "usb3_ports" = "{ |
| [0] = USB3_PORT_DEFAULT(OC0), |
| [1] = USB3_PORT_DEFAULT(OC0), |
| [2] = USB3_PORT_DEFAULT(OC3), |
| [3] = USB3_PORT_DEFAULT(OC3), |
| [4] = USB3_PORT_DEFAULT(OC1), |
| [5] = USB3_PORT_DEFAULT(OC1), |
| [6] = USB3_PORT_DEFAULT(OC_SKIP), |
| [7] = USB3_PORT_DEFAULT(OC_SKIP), |
| [8] = USB3_PORT_DEFAULT(OC_SKIP), |
| [9] = USB3_PORT_DEFAULT(OC_SKIP), |
| }" |
| end |
| device ref thermal on |
| subsystemid 0x1849 0xa131 |
| end |
| device ref heci1 on |
| subsystemid 0x1849 0xa131 |
| end |
| device ref sata on |
| subsystemid 0x1849 0xa102 |
| register "SataSalpSupport" = "1" |
| # SATA4 and SATA5 are located in the lower right corner of the board, |
| # but they are not populated. This is because the same PCB is used to |
| # make boards with better PCHs, which can have up to six SATA ports. |
| # However, the H110 PCH only has four SATA ports, which explains why |
| # two connectors are missing. |
| register "SataPortsEnable" = "{ |
| [0] = 1, |
| [1] = 1, |
| [2] = 1, |
| [3] = 1, |
| }" |
| end |
| device ref pcie_rp1 on end |
| device ref pcie_rp5 on |
| register "PcieRpEnable[4]" = "1" |
| register "PcieRpClkReqSupport[4]" = "1" |
| register "PcieRpClkReqNumber[4]" = "2" |
| register "PcieRpAdvancedErrorReporting[4]" = "1" |
| register "PcieRpLtrEnable[4]" = "1" |
| register "PcieRpClkSrcNumber[4]" = "2" |
| register "PcieRpHotPlug[4]" = "1" |
| end |
| device ref pcie_rp6 on |
| register "PcieRpEnable[5]" = "1" |
| |
| # Disable CLKREQ#, since onboard LAN is always present |
| register "PcieRpClkReqSupport[5]" = "0" |
| register "PcieRpAdvancedErrorReporting[5]" = "1" |
| register "PcieRpLtrEnable[5]" = "1" |
| register "PcieRpClkSrcNumber[5]" = "1" |
| end |
| device ref pcie_rp7 on |
| register "PcieRpEnable[6]" = "1" |
| register "PcieRpClkReqSupport[6]" = "1" |
| register "PcieRpClkReqNumber[6]" = "3" |
| register "PcieRpAdvancedErrorReporting[6]" = "1" |
| register "PcieRpLtrEnable[6]" = "1" |
| register "PcieRpClkSrcNumber[6]" = "3" |
| register "PcieRpHotPlug[6]" = "1" |
| end |
| device ref lpc_espi on |
| subsystemid 0x1849 0x1a43 |
| |
| # Set @0x280-0x2ff I/O Range for SuperIO HWM |
| register "gen1_dec" = "0x007c0281" |
| |
| # Set LPC Serial IRQ mode |
| register "serirq_mode" = "SERIRQ_CONTINUOUS" |
| |
| chip superio/common |
| device pnp 2e.0 on # passes SIO base addr to SSDT gen |
| |
| chip superio/nuvoton/nct6791d |
| device pnp 2e.1 on |
| # Global Control Registers |
| # Device IRQ Polarity |
| irq 0x13 = 0x00 |
| irq 0x14 = 0x00 |
| # Global Option |
| irq 0x24 = 0xfb |
| irq 0x27 = 0x10 |
| # Multi Function |
| irq 0x1a = 0xb0 |
| irq 0x1b = 0xe6 |
| irq 0x2a = 0x04 |
| irq 0x2c = 0x40 |
| irq 0x2d = 0x03 |
| |
| # Parallel Port |
| io 0x60 = 0x0378 |
| irq 0x70 = 7 |
| drq 0x74 = 4 # No DMA |
| irq 0xf0 = 0x3c # Printer mode |
| end |
| device pnp 2e.2 on # UART A |
| io 0x60 = 0x03f8 |
| irq 0x70 = 4 |
| end |
| device pnp 2e.3 on # IR |
| io 0x60 = 0x02f8 |
| irq 0x70 = 3 |
| end |
| device pnp 2e.5 on # PS/2 KBC |
| io 0x60 = 0x0060 |
| io 0x62 = 0x0064 |
| irq 0x70 = 1 # Keyboard |
| irq 0x72 = 12 # Mouse |
| end |
| device pnp 2e.6 off end # CIR |
| device pnp 2e.7 on # GPIO6 |
| irq 0xf6 = 0xff |
| irq 0xf7 = 0xff |
| irq 0xf8 = 0xff |
| end |
| device pnp 2e.107 on # GPIO7 |
| irq 0xe0 = 0x7f |
| irq 0xe1 = 0x0d |
| end |
| device pnp 2e.207 on # GPIO8 |
| irq 0xe6 = 0xff |
| irq 0xe7 = 0xff |
| irq 0xed = 0xff |
| end |
| device pnp 2e.8 off end # WDT |
| device pnp 2e.108 on end # GPIO0 |
| device pnp 2e.308 off end # GPIO base |
| device pnp 2e.408 off end # WDTMEM |
| device pnp 2e.708 on end # GPIO1 |
| device pnp 2e.9 on end # GPIO2 |
| device pnp 2e.109 on # GPIO3 |
| irq 0xe4 = 0x7b |
| irq 0xe5 = 0x02 |
| irq 0xea = 0x04 |
| end |
| device pnp 2e.209 on # GPIO4 |
| irq 0xf0 = 0x7f |
| irq 0xf1 = 0x80 |
| end |
| device pnp 2e.309 on # GPIO5 |
| irq 0xf4 = 0xdf |
| irq 0xf5 = 0xd5 |
| end |
| device pnp 2e.a on |
| # Power RAM in S3 and let the PCH |
| # handle power failure actions |
| irq 0xe4 = 0x70 |
| # Set HWM reset source to LRESET# |
| irq 0xe7 = 0x01 |
| end # ACPI |
| device pnp 2e.b on # HWM, LED |
| io 0x60 = 0x0290 |
| io 0x62 = 0 |
| irq 0x70 = 0 |
| end |
| device pnp 2e.d off end # BCLK, WDT2, WDT_MEM |
| device pnp 2e.e off end # CIR wake-up |
| device pnp 2e.f off end # GPIO PP/OD |
| device pnp 2e.14 off end # SVID, Port 80 UART |
| device pnp 2e.16 off end # DS5 |
| device pnp 2e.116 off end # DS3 |
| device pnp 2e.316 on end # PCHDSW |
| device pnp 2e.416 off end # DSWWOPT |
| device pnp 2e.516 on end # DS3OPT |
| device pnp 2e.616 on end # DSDSS |
| device pnp 2e.716 off end # DSPU |
| end # chip superio/nuvoton/nct6791d |
| |
| end # device pnp 2e.0 |
| end # chip superio/common |
| |
| chip drivers/pc80/tpm |
| device pnp 4e.0 on end # TPM module |
| end |
| end |
| device ref hda on |
| register "PchHdaVcType" = "Vc1" |
| end |
| device ref smbus on end |
| device ref fast_spi on end |
| end |
| end |