| fw_config |
| field WIFI 10 11 |
| option UNKNOWN 0 |
| option WIFI_6 1 |
| option WIFI_6E 2 |
| end |
| field CAMERA 12 13 |
| option UF_720P_WF 0 |
| option UF_1080P 1 |
| option UF_720P 2 |
| option UF_1080P_WF 3 |
| end |
| field DB_AUX_BIAS 3 4 |
| option REDRIVER 0 |
| option SOC 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-42.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10051" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-42.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515" |
| |
| # FIVR configurations for anraggar are disabled since the board doesn't have V1p05 and Vnn |
| # bypass rails implemented. |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 0, |
| }" |
| |
| # Enable the Cnvi BT Audio Offload |
| register "cnvi_bt_audio_offload" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------+------------------------------+ |
| #| Field | Value | |
| #+-------------+------------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | Sub-board(PSensor)/WCAM | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------+------------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 160, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 152, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| }" |
| |
| # Power limit config |
| register "power_limits_config[ADL_N_041_6W_CORE]" = "{ |
| .tdp_pl1_override = 15, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""CPU_VR"" |
| register "options.tsr[1].desc" = ""CPU"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| register "options.tsr[3].desc" = ""Charger"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| [4] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_3, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_2, 80, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 6000, |
| .max_power = 15000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on end |
| end |
| end |
| device ref igpu on |
| chip drivers/gfx/generic |
| register "device_count" = "4" |
| # DDIA for eDP |
| register "device[0].name" = ""LCD0"" |
| # Internal panel on the first port of the graphics chip |
| register "device[0].type" = "panel" |
| # DDIB for HDMI |
| # If HDMI is not enumerated in the kernel, then no GFX device should be added for DDIB |
| register "device[1].name" = ""DD01"" |
| # TCP0 (DP-1) for port C0 |
| register "device[2].name" = ""DD02"" |
| register "device[2].use_pld" = "true" |
| register "device[2].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| # TCP1 (DP-2) for port C1 |
| register "device[3].name" = ""DD03"" |
| register "device[3].use_pld" = "true" |
| register "device[3].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device generic 0 on end |
| end |
| end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "1" |
| device generic 0 on |
| probe CAMERA UF_720P_WF |
| probe CAMERA UF_1080P_WF |
| end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ILTK0001"" |
| register "generic.desc" = ""ILITEK Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "200" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C6)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "200" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 41 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" |
| register "key.wake_gpe" = "GPE0_DW2_15" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_ANY" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTIDB10"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 13b10 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "4" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "560 * MHz" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1200_WCAM_X |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on |
| probe CAMERA UF_720P_WF |
| probe CAMERA UF_1080P_WF |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "2" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW9714 VCM "" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_AFVDD |
| |
| #_ON |
| register "on_seq.ops_cnt" = "1" |
| register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "1" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 0C on |
| probe CAMERA UF_720P_WF |
| probe CAMERA UF_1080P_WF |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24P64E"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c64"" |
| |
| device i2c 50 on |
| probe CAMERA UF_720P_WF |
| probe CAMERA UF_1080P_WF |
| end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5650"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5650"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-mode"" |
| register "property_list[0].integer" = "2" |
| device i2c 1a on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""PRIMAX Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| register "enable_cnvi_ddr_rfim" = "true" |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp4 on |
| # PCIe 4 WLAN |
| register "pch_pcie_rp[PCH_RP(4)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW1_03" |
| register "add_acpi_dma_property" = "true" |
| device pci 00.0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C MB (7.5 inch) |
| register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C DB (7.1 inch) |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MB (6.4 inch) |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Type-A DB (6.2 inch) |
| register "usb2_ports[4]" = "USB2_PORT_SHORT(OC_SKIP)" # LTE (3.3 inch) |
| register "usb2_ports[5]" = "USB2_PORT_SHORT(OC_SKIP)" # UFC (3.7 inch) |
| register "usb2_ports[7]" = "USB2_PORT_SHORT(OC_SKIP)" # Bluetooth port for PCIe WLAN (2.5 inch) |
| register "usb2_ports[9]" = "USB2_PORT_SHORT(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 Type-A port A0(MLB)) |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 Type-A port A1(DB) |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 WWAN(LTE) |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 UFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""PCIe Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""CNVi Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WLAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end |
| device ref pcie_rp7 off end # SDCard |
| device ref hda on |
| chip drivers/sof |
| register "spkr_tplg" = "rt5650_sp" |
| register "jack_tplg" = "rt5650_hp" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on end |
| end |
| end |
| end |
| end |