| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2008 Uwe Hermann <uwe@hermann-uwe.de> |
| * Copyright (C) 2010,2017 Keith Hui <buurin@gmail.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <spd.h> |
| #include <delay.h> |
| #include <stdint.h> |
| #include <stdlib.h> |
| #include <device/mmio.h> |
| #include <device/pci_ops.h> |
| #include <device/pci_def.h> |
| #include <console/console.h> |
| #include "i440bx.h" |
| #include "raminit.h" |
| |
| /* |
| * Macros and definitions |
| */ |
| |
| /* Debugging macros. */ |
| #if CONFIG(DEBUG_RAM_SETUP) |
| #define PRINT_DEBUG(x...) printk(BIOS_DEBUG, x) |
| #define DUMPNORTH() dump_pci_device(NB) |
| #else |
| #define PRINT_DEBUG(x...) |
| #define DUMPNORTH() |
| #endif |
| |
| /* SDRAMC[7:5] - SDRAM Mode Select (SMS). */ |
| #define RAM_COMMAND_NORMAL 0x0 |
| #define RAM_COMMAND_NOP 0x1 |
| #define RAM_COMMAND_PRECHARGE 0x2 |
| #define RAM_COMMAND_MRS 0x3 |
| #define RAM_COMMAND_CBR 0x4 |
| |
| /* Map the JEDEC SPD refresh rates (array index) to 440BX refresh rates as |
| * defined in DRAMC[2:0]. |
| * |
| * [0] == Normal 15.625 us -> 15.6 us |
| * [1] == Reduced(.25X) 3.9 us -> 7.8 ns |
| * [2] == Reduced(.5X) 7.8 us -> 7.8 us |
| * [3] == Extended(2x) 31.3 us -> 31.2 us |
| * [4] == Extended(4x) 62.5 us -> 62.4 us |
| * [5] == Extended(8x) 125 us -> 124.8 us |
| */ |
| static const uint32_t refresh_rate_map[] = { |
| 1, 5, 5, 2, 3, 4 |
| }; |
| |
| /* Table format: register, bitmask, value. */ |
| static const u8 register_values[] = { |
| /* NBXCFG - NBX Configuration Register |
| * 0x50 - 0x53 |
| * |
| * [31:24] SDRAM Row Without ECC |
| * 0 = ECC components are populated in this row |
| * 1 = ECC components are not populated in this row |
| * [23:19] Reserved |
| * [18:18] Host Bus Fast Data Ready Enable (HBFDRE) |
| * Assertion of DRAM data on host bus occurs... |
| * 0 = ...one clock after sampling snoop results (default) |
| * 1 = ...on the same clock the snoop result is being sampled |
| * (this mode is faster by one clock cycle) |
| * [17:17] ECC - EDO static Drive mode |
| * 0 = Normal mode (default) |
| * 1 = ECC signals are always driven |
| * [16:16] IDSEL_REDIRECT |
| * 0 = IDSEL1 is allocated to this bridge (default) |
| * 1 = IDSEL7 is allocated to this bridge |
| * [15:15] WSC# Handshake Disable |
| * 1 = Uni-processor mode |
| * 0 = Dual-processor mode with external IOAPIC (default) |
| * [14:14] Intel Reserved |
| * [13:12] Host/DRAM Frequency |
| * 00 = 100 MHz |
| * 01 = Reserved |
| * 10 = 66 MHz |
| * 11 = Reserved |
| * [11:11] AGP to PCI Access Enable |
| * 1 = Enable |
| * 0 = Disable |
| * [10:10] PCI Agent to Aperture Access Disable |
| * 1 = Disable |
| * 0 = Enable (default) |
| * [09:09] Aperture Access Global Enable |
| * 1 = Enable |
| * 0 = Disable |
| * [08:07] DRAM Data Integrity Mode (DDIM) |
| * 00 = Non-ECC |
| * 01 = EC-only |
| * 10 = ECC Mode |
| * 11 = ECC Mode with hardware scrubbing enabled |
| * [06:06] ECC Diagnostic Mode Enable (EDME) |
| * 1 = Enable |
| * 0 = Normal operation mode (default) |
| * [05:05] MDA Present (MDAP) |
| * Works in conjunction with the VGA_EN bit. |
| * VGA_EN MDAP |
| * 0 x All VGA cycles are sent to PCI |
| * 1 0 All VGA cycles are sent to AGP |
| * 1 1 All VGA cycles are sent to AGP, except for |
| * cycles in the MDA range. |
| * [04:04] Reserved |
| * [03:03] USWC Write Post During I/O Bridge Access Enable (UWPIO) |
| * 1 = Enable |
| * 0 = Disable |
| * [02:02] In-Order Queue Depth (IOQD) |
| * 1 = In-order queue = maximum |
| * 0 = A7# is sampled asserted (i.e., 0) |
| * [01:00] Reserved |
| */ |
| NBXCFG + 0, 0x00, 0x0c, |
| // TODO: Bit 15 should be 0 for multiprocessor boards |
| NBXCFG + 1, 0x00, 0x80, |
| NBXCFG + 2, 0x00, 0x00, |
| NBXCFG + 3, 0x00, 0xff, |
| |
| /* DRAMC - DRAM Control Register |
| * 0x57 |
| * |
| * [7:6] Reserved |
| * [5:5] Module Mode Configuration (MMCONFIG) |
| * The combination of SDRAMPWR and this bit (set by an |
| * external strapping option) determine how CKE works. |
| * SDRAMPWR MMCONFIG |
| * 0 0 = 3 DIMM, CKE[5:0] driven |
| * X 1 = 3 DIMM, CKE0 only |
| * 1 0 = 4 DIMM, GCKE only |
| * [4:3] DRAM Type (DT) |
| * 00 = EDO |
| * 01 = SDRAM |
| * 10 = Registered SDRAM |
| * 11 = Reserved |
| * Note: EDO, SDRAM and Registered SDRAM cannot be mixed. |
| * [2:0] DRAM Refresh Rate (DRR) |
| * 000 = Refresh disabled |
| * 001 = 15.6 us |
| * 010 = 31.2 us |
| * 011 = 62.4 us |
| * 100 = 124.8 us |
| * 101 = 249.6 us |
| * 110 = Reserved |
| * 111 = Reserved |
| */ |
| /* Choose SDRAM (not registered), and disable refresh for now. */ |
| DRAMC, 0x00, 0x08, |
| |
| /* |
| * PAM[6:0] - Programmable Attribute Map Registers |
| * 0x59 - 0x5f |
| * |
| * 0x59 [3:0] Reserved |
| * 0x59 [5:4] 0xF0000 - 0xFFFFF BIOS area |
| * 0x5a [1:0] 0xC0000 - 0xC3FFF ISA add-on BIOS |
| * 0x5a [5:4] 0xC4000 - 0xC7FFF ISA add-on BIOS |
| * 0x5b [1:0] 0xC8000 - 0xCBFFF ISA add-on BIOS |
| * 0x5b [5:4] 0xCC000 - 0xCFFFF ISA add-on BIOS |
| * 0x5c [1:0] 0xD0000 - 0xD3FFF ISA add-on BIOS |
| * 0x5c [5:4] 0xD4000 - 0xD7FFF ISA add-on BIOS |
| * 0x5d [1:0] 0xD8000 - 0xDBFFF ISA add-on BIOS |
| * 0x5d [5:4] 0xDC000 - 0xDFFFF ISA add-on BIOS |
| * 0x5e [1:0] 0xE0000 - 0xE3FFF BIOS extension |
| * 0x5e [5:4] 0xE4000 - 0xE7FFF BIOS extension |
| * 0x5f [1:0] 0xE8000 - 0xEBFFF BIOS extension |
| * 0x5f [5:4] 0xEC000 - 0xEFFFF BIOS extension |
| * |
| * Bit assignment: |
| * 00 = DRAM Disabled (all access goes to memory mapped I/O space) |
| * 01 = Read Only (Reads to DRAM, writes to memory mapped I/O space) |
| * 10 = Write Only (Writes to DRAM, reads to memory mapped I/O space) |
| * 11 = Read/Write (all access goes to DRAM) |
| */ |
| |
| /* |
| * Map all legacy regions to RAM (read/write). This is required if |
| * you want to use the RAM area from 768 KB - 1 MB. If the PAM |
| * registers are not set here appropriately, the RAM in that region |
| * will not be accessible, thus a RAM check of it will also fail. |
| */ |
| PAM0, 0x00, 0x30, |
| PAM1, 0x00, 0x33, |
| PAM2, 0x00, 0x33, |
| PAM3, 0x00, 0x33, |
| PAM4, 0x00, 0x33, |
| PAM5, 0x00, 0x33, |
| PAM6, 0x00, 0x33, |
| |
| /* DRB[0:7] - DRAM Row Boundary Registers |
| * 0x60 - 0x67 |
| * |
| * An array of 8 byte registers, which hold the ending memory address |
| * assigned to each pair of DIMMs, in 8MB granularity. |
| * |
| * 0x60 DRB0 = Total memory in row0 (in 8 MB) |
| * 0x61 DRB1 = Total memory in row0+1 (in 8 MB) |
| * 0x62 DRB2 = Total memory in row0+1+2 (in 8 MB) |
| * 0x63 DRB3 = Total memory in row0+1+2+3 (in 8 MB) |
| * 0x64 DRB4 = Total memory in row0+1+2+3+4 (in 8 MB) |
| * 0x65 DRB5 = Total memory in row0+1+2+3+4+5 (in 8 MB) |
| * 0x66 DRB6 = Total memory in row0+1+2+3+4+5+6 (in 8 MB) |
| * 0x67 DRB7 = Total memory in row0+1+2+3+4+5+6+7 (in 8 MB) |
| */ |
| /* DRBs will be set later. */ |
| DRB0, 0x00, 0x00, |
| DRB1, 0x00, 0x00, |
| DRB2, 0x00, 0x00, |
| DRB3, 0x00, 0x00, |
| DRB4, 0x00, 0x00, |
| DRB5, 0x00, 0x00, |
| DRB6, 0x00, 0x00, |
| DRB7, 0x00, 0x00, |
| |
| /* FDHC - Fixed DRAM Hole Control Register |
| * 0x68 |
| * |
| * Controls two fixed DRAM holes: 512 KB - 640 KB and 15 MB - 16 MB. |
| * |
| * [7:6] Hole Enable (HEN) |
| * 00 = None |
| * 01 = 512 KB - 640 KB (128 KB) |
| * 10 = 15 MB - 16 MB (1 MB) |
| * 11 = Reserved |
| * [5:0] Reserved |
| */ |
| /* No memory holes. */ |
| FDHC, 0x00, 0x00, |
| |
| /* RPS - SDRAM Row Page Size Register |
| * 0x74 - 0x75 |
| * |
| * Sets the row page size for SDRAM. For EDO memory, the page |
| * size is fixed at 2 KB. |
| * |
| * Bits[1:0] Page Size |
| * 00 2 KB |
| * 01 4 KB |
| * 10 8 KB |
| * 11 Reserved |
| * |
| * RPS bits Corresponding DRB register |
| * [01:00] DRB[0], row 0 |
| * [03:02] DRB[1], row 1 |
| * [05:04] DRB[2], row 2 |
| * [07:06] DRB[3], row 3 |
| * [09:08] DRB[4], row 4 |
| * [11:10] DRB[5], row 5 |
| * [13:12] DRB[6], row 6 |
| * [15:14] DRB[7], row 7 |
| */ |
| /* Power on defaults to 2KB. Will be set later. */ |
| // RPS + 0, 0x00, 0x00, |
| // RPS + 1, 0x00, 0x00, |
| |
| /* SDRAMC - SDRAM Control Register |
| * 0x76 - 0x77 |
| * |
| * [15:10] Reserved |
| * [09:08] Idle/Pipeline DRAM Leadoff Timing (IPDLT) |
| * 00 = Illegal |
| * 01 = Add a clock delay to the lead-off clock count |
| * 1x = Illegal |
| * [07:05] SDRAM Mode Select (SMS) |
| * 000 = Normal SDRAM Operation (default) |
| * 001 = NOP Command Enable |
| * 010 = All Banks Precharge Enable |
| * 011 = Mode Register Set Enable |
| * 100 = CBR Enable |
| * 101 = Reserved |
| * 110 = Reserved |
| * 111 = Reserved |
| * [04:04] SDRAMPWR |
| * 0 = 3 DIMM configuration |
| * 1 = 4 DIMM configuration |
| * [03:03] Leadoff Command Timing (LCT) |
| * 0 = 4 CS# Clock |
| * 1 = 3 CS# Clock |
| * [02:02] CAS# Latency (CL) |
| * 0 = 3 DCLK CAS# latency |
| * 1 = 2 DCLK CAS# latency |
| * [01:01] SDRAM RAS# to CAS# Delay (SRCD) |
| * 0 = 3 clocks between a row activate and a read or write cmd. |
| * 1 = 2 clocks between a row activate and a read or write cmd. |
| * [00:00] SDRAM RAS# Precharge (SRP) |
| * 0 = 3 clocks of RAS# precharge |
| * 1 = 2 clocks of RAS# precharge |
| */ |
| #if CONFIG(SDRAMPWR_4DIMM) |
| SDRAMC + 0, 0x00, 0x10, /* The board has 4 DIMM slots. */ |
| #else |
| SDRAMC + 0, 0x00, 0x00, /* The board has 3 DIMM slots. */ |
| #endif |
| |
| /* PGPOL - Paging Policy Register |
| * 0x78 - 0x79 |
| * |
| * [15:08] Banks per Row (BPR) |
| * Each bit in this field corresponds to one row of the memory |
| * array. Bit 15 corresponds to row 7 while bit 8 corresponds |
| * to row 0. Bits for empty rows are "don't care". |
| * 0 = 2 banks |
| * 1 = 4 banks |
| * [07:05] Reserved |
| * [04:04] Intel Reserved |
| * [03:00] DRAM Idle Timer (DIT) |
| * 0000 = 0 clocks |
| * 0001 = 2 clocks |
| * 0010 = 4 clocks |
| * 0011 = 8 clocks |
| * 0100 = 10 clocks |
| * 0101 = 12 clocks |
| * 0110 = 16 clocks |
| * 0111 = 32 clocks |
| * 1xxx = Infinite (pages are not closed for idle condition) |
| */ |
| PGPOL + 0, 0x00, 0x00, |
| PGPOL + 1, 0x00, 0xff, |
| |
| /* PMCR - Power Management Control Register |
| * 0x7a |
| * |
| * [07:07] Power Down SDRAM Enable (PDSE) |
| * 1 = Enable |
| * 0 = Disable |
| * [06:06] ACPI Control Register Enable (SCRE) |
| * 1 = Enable |
| * 0 = Disable (default) |
| * [05:05] Suspend Refresh Type (SRT) |
| * 1 = Self refresh mode |
| * 0 = CBR fresh mode |
| * [04:04] Normal Refresh Enable (NREF_EN) |
| * 1 = Enable |
| * 0 = Disable |
| * [03:03] Quick Start Mode (QSTART) |
| * 1 = Quick start mode for the processor is enabled |
| * [02:02] Gated Clock Enable (GCLKEN) |
| * 1 = Enable |
| * 0 = Disable |
| * [01:01] AGP Disable (AGP_DIS) |
| * 1 = Disable |
| * 0 = Enable |
| * [00:00] CPU reset without PCIRST enable (CRst_En) |
| * 1 = Enable |
| * 0 = Disable |
| */ |
| /* Enable normal refresh and the gated clock. */ |
| // TODO: Only do this later? |
| // PMCR, 0x00, 0x14, |
| PMCR, 0x00, 0x00, |
| |
| /* Enable SCRR.SRRAEN and let BX choose the SRR. */ |
| SCRR + 1, 0x00, 0x10, |
| }; |
| |
| /*----------------------------------------------------------------------------- |
| SDRAM configuration functions. |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Send the specified RAM command to all DIMMs. |
| * |
| * @param command The RAM command to send to the DIMM(s). |
| */ |
| static void do_ram_command(u32 command) |
| { |
| int i, caslatency; |
| u8 dimm_start, dimm_end; |
| u16 reg16; |
| void *addr; |
| u32 addr_offset; |
| |
| /* Configure the RAM command. */ |
| reg16 = pci_read_config16(NB, SDRAMC); |
| reg16 &= 0xff1f; /* Clear bits 7-5. */ |
| reg16 |= (u16) (command << 5); /* Write command into bits 7-5. */ |
| pci_write_config16(NB, SDRAMC, reg16); |
| |
| /* |
| * RAM_COMMAND_NORMAL affects only the memory controller and |
| * doesn't need to be "sent" to the DIMMs. |
| */ |
| if (command == RAM_COMMAND_NORMAL) |
| return; |
| |
| /* Send the RAM command to each row of memory. */ |
| dimm_start = 0; |
| for (i = 0; i < (DIMM_SOCKETS * 2); i++) { |
| addr_offset = 0; |
| caslatency = 3; /* TODO: Dynamically get CAS latency later. */ |
| if (command == RAM_COMMAND_MRS) { |
| /* |
| * MAA[12:11,9:0] must be inverted when sent to DIMM |
| * 2 or 3 (no inversion if sent to DIMM 0 or 1). |
| */ |
| if ((i >= 0 && i <= 3) && caslatency == 3) |
| addr_offset = 0x1d0; |
| if ((i >= 4 && i <= 7) && caslatency == 3) |
| addr_offset = 0x1e28; |
| if ((i >= 0 && i <= 3) && caslatency == 2) |
| addr_offset = 0x150; |
| if ((i >= 4 && i <= 7) && caslatency == 2) |
| addr_offset = 0x1ea8; |
| } |
| |
| dimm_end = pci_read_config8(NB, DRB + i); |
| |
| addr = (void *)((dimm_start * 8 * 1024 * 1024) + addr_offset); |
| if (dimm_end > dimm_start) { |
| read32(addr); |
| } |
| |
| /* Set the start of the next DIMM. */ |
| dimm_start = dimm_end; |
| } |
| } |
| |
| static void set_dram_buffer_strength(void) |
| { |
| /* |
| * Program MBSC[39:0] and MBFS[23:0]. |
| * |
| * The 440BX datasheet says buffer frequency is independent from bus |
| * frequency and mismatch both ways are possible. |
| * |
| * MBSC[47:40] and MBFS[23] are reserved. |
| */ |
| |
| unsigned int i, reg, drb; |
| uint8_t mbsc0, mbfs0, mbfs1, mbfs2; |
| uint16_t mbsc1, mbsc3; |
| |
| /* |
| * Tally how many rows between rows 0-3 and rows 4-7 are populated. |
| * This determines how to program MBFS and MBSC. |
| */ |
| uint8_t dimm03 = 0; |
| uint8_t dimm47 = 0; |
| |
| for (drb = 0, i = DRB0; i <= DRB7; i++) { |
| reg = pci_read_config8(NB, i); |
| if (drb != reg) { |
| if (i <= DRB3) |
| dimm03++; |
| else |
| dimm47++; |
| |
| drb = reg; |
| } |
| } |
| |
| if (CONFIG(SDRAMPWR_4DIMM)) { |
| /* |
| * For a 4 DIMM board, based on ASUS P2B-LS mainboard. |
| * |
| * There are four main conditions to check when programming |
| * DRAM buffer frequency and strength: |
| * |
| * a: >2 rows populated across DIMM0,1 |
| * b: >2 rows populated across DIMM2,3 |
| * c: >4 rows populated across all DIMM slots |
| * and either one of: |
| * 1: NBXCFG[13] strapped as 100MHz, or |
| * 6: NBXCFG[13] strapped as 66MHz |
| * |
| * CKE0/FENA ----------------------------------------------------------+ |
| * CKE1/GCKE ----------------------[ MBFS ]---------------------+| |
| * DQMA/CASA[764320]# -------------[ 0 = 66MHz ]--------------------+|| |
| * DQMB1/CASB1# (Fixed for 66MHz) -[ 1 = 100MHz ]-------------------+||| |
| * DQMB5/CASB5# (Fixed for 66MHz) ---------------------------------+|||| |
| * DQMA1/CASA1# (Fixed for 66MHz) --------------------------------+||||| |
| * DQMA5/CASA5# (Fixed for 66MHz) -------------------------------+|||||| |
| * CSA[5:0]#,CSB[5:0]# ------------------------------------++++++||||||| |
| * CS[B7,A7,B6,A6]#/CKE[5342] -------------------------++++||||||||||||| |
| * MECC[7:0] #2/#1 ----------------------------------++||||||||||||||||| |
| * MD[63:0] #2/#1 ---------------------------------++||||||||||||||||||| |
| * MAB[12:11,9:0]#,MAB[13,10],WEB#,SRASB#,SCASB# -+||||||||||||||||||||| |
| * MAA[13:0],WEA#,SRASA#,SCASA# -----------------+|||||||||||||||||||||| |
| * Reserved ------------------------------------+||||||||||||||||||||||| |
| * |||||||||||||||||||||||| |
| * 3 32 21 10 0 * 2 21 10 0 |
| * 9876543210987654321098765432109876543210 * 321098765432109876543210 |
| * 10------------------------1010---------- a -1---------------11----- |
| * 11------------------------1111---------- !a -0---------------00----- |
| * --10--------------------------1010------ b --1----------------11--- |
| * --11--------------------------1111------ !b --0----------------00--- |
| * ----------------------------------1100-- c ----------------------1- |
| * ----------------------------------1011-- !c ----------------------0- |
| * ----1010101000000000000000------------00 1 ---11111111111111----1-0 |
| * ----000000000000000000000010101010----00 6 ---1111111111111100000-0 |
| * | | | | | | | | | | ||||||| | | | | | | |
| * | | | | | | | | | | ||||||| | | | | | +- CKE0/FENA |
| * | | | | | | | | | | ||||||| | | | | +--- CKE1/GCKE |
| * | | | | | | | | | | ||||||| | | | +----- DQMA/CASA[764320]# |
| * | | | | | | | | | | ||||||| | | +------- DQMB1/CASB1# (66MHz: 2x) |
| * | | | | | | | | | | ||||||| | +--------- DQMB5/CASB5# (66MHz: 2x) |
| * | | | | | | | | | | ||||||| +----------- DQMA1/CASA1# (66MHz: 2x) |
| * | | | | | | | | | | ||||||+------------- DQMA5/CASA5# (66MHz: 2x) |
| * | | | | | | | | | | ++++++-------------- CSA0-5#,CSB0-5# (1x) |
| * | | | | | | | | | +--------------------- CSA6#/CKE2 |
| * | | | | | | | | +---[ MBSC ]------ CSB6#/CKE4 |
| * | | | | | | | +-----[ 00 = 1x ]------ CSA7#/CKE3 |
| * | | | | | | +-------[ 01 invalid ]------ CSB7#/CKE5 |
| * | | | | | +---------[ 10 = 2x ]------ MECC[7:0] #1 |
| * | | | | +-----------[ 11 = 3x ]------ MECC[7:0] #2 |
| * | | | +--------------------------------- MD[63:0] #1 |
| * | | +----------------------------------- MD[63:0] #2 |
| * | +------------------ MAB[12:11,9:0]#,MAB[13,10],WEB#,SRASB#,SCASB# |
| * +------------------------------------- MAA[13:0],WEA#,SRASA#,SCASA# |
| */ |
| unsigned int fsb; |
| |
| mbsc0 = 0xa0; |
| mbsc1 = 0x002a; |
| mbfs1 = 0xff; |
| mbfs2 = 0x1f; |
| if (pci_read_config8(NB, NBXCFG + 1) & 0x30) { |
| fsb = 66; |
| mbsc3 = 0xa000; |
| mbfs0 = 0x80; |
| } else { |
| fsb = 100; |
| mbsc3 = 0xaaa0; |
| mbfs0 = 0x84; |
| } |
| if (dimm03 > 2) { |
| mbfs2 |= 0x40; |
| if (fsb == 100) |
| mbfs0 |= 0x60; |
| } else { |
| mbsc3 |= 0xc000; |
| if (fsb == 100) |
| mbsc1 |= 0x003c; |
| } |
| if (dimm47 > 2) { |
| mbfs2 |= 0x20; |
| if (fsb == 100) |
| mbfs0 |= 0x18; |
| } else { |
| mbsc3 |= 0x3000; |
| if (fsb == 100) { |
| mbsc1 |= 0x0003; |
| mbsc0 |= 0xc0; |
| } |
| } |
| if ((dimm03 + dimm47) > 4) { |
| mbsc0 |= 0x30; |
| mbfs0 |= 0x02; |
| } else { |
| mbsc0 |= 0x2c; |
| } |
| } else { |
| /* |
| * For a 3 DIMM board, based on ASUS P2B mainboard. |
| * |
| * There are two main conditions to check when programming DRAM buffer |
| * frequency and strength: |
| * |
| * a: >2 rows populated across DIMM0,1 |
| * c: >4 rows populated across all DIMM slots |
| * |
| * CKE0 ---------------------------------------------------------------+ |
| * CKE1 ------------------------[ MBFS ]------------------------+| |
| * DQMA/CASA[764320]# ----------[ 0 = 66MHz ]-----------------------+|| |
| * DQMB1/CASB1# ----------------[ 1 = 100MHz ]----------------------+||| |
| * DQMB5/CASB5# ---------------------------------------------------+|||| |
| * DQMA1/CASA1# --------------------------------------------------+||||| |
| * DQMA5/CASA5# -------------------------------------------------+|||||| |
| * CSA0-5#,CSB0-5# ----------------------------------------++++++||||||| |
| * CS[B7,A7,B6,A6]#/CKE[5342] -------------------------++++||||||||||||| |
| * MECC[7:0] #2/#1 (100MHz) -------------------------++||||||||||||||||| |
| * MD[63:0] #2/#1 (100MHz) ------------------------++||||||||||||||||||| |
| * MAB[12:11,9:0]#,MAB[13,10],WEB#,SRASB#,SCASB# -+||||||||||||||||||||| |
| * MAA[13:0],WEA#,SRASA#,SCASA# -----------------+|||||||||||||||||||||| |
| * Reserved ------------------------------------+||||||||||||||||||||||| |
| * |||||||||||||||||||||||| |
| * 3 32 21 10 0 * 2 21 10 0 |
| * 9876543210987654321098765432109876543210 * 321098765432109876543210 |
| * 10------------------------1111---------- a -1---------------------- |
| * 11------------------------1010---------- !a -0---------------------- |
| * --110000000010101010111111----1010--1010 * --01111000000000000000-0 |
| * ----------------------------------11---- c ----------------------1- |
| * ----------------------------------10---- !c ----------------------0- |
| * | | | | | | | | | | ||||||| | | | | | | |
| * | | | | | | | | | | ||||||| | | | | | +- CKE0 |
| * | | | | | | | | | | ||||||| | | | | +--- CKE1 |
| * | | | | | | | | | | ||||||| | | | +----- DQMA/CASA[764320]# |
| * | | | | | | | | | | ||||||| | | +------- DQMB1/CASB1# |
| * | | | | | | | | | | ||||||| | +--------- DQMB5/CASB5# |
| * | | | | | | | | | | ||||||| +----------- DQMA1/CASA1# |
| * | | | | | | | | | | ||||||+------------- DQMA5/CASA5# |
| * | | | | | | | | | | ++++++-------------- CSA0-5#,CSB0-5# (2x) |
| * | | | | | | | | | +--------------------- CSA6#/CKE2 |
| * | | | | | | | | +---[ MBSC ]------ CSB6#/CKE4 |
| * | | | | | | | +-----[ 00 = 1x ]------ CSA7#/CKE3 |
| * | | | | | | +-------[ 01 invalid ]------ CSB7#/CKE5 |
| * | | | | | +---------[ 10 = 2x ]------ MECC[7:0] #1 (1x) |
| * | | | | +-----------[ 11 = 3x ]------ MECC[7:0] #2 (1x) |
| * | | | +--------------------------------- MD[63:0] #1 (1x) |
| * | | +----------------------------------- MD[63:0] #2 (1x) |
| * | +------------------ MAB[12:11,9:0]#,MAB[13,10],WEB#,SRASB#,SCASB# |
| * +------------------------------------- MAA[13:0],WEA#,SRASA#,SCASA# |
| */ |
| |
| mbsc0 = 0xaa; |
| mbsc1 = 0xafea; |
| mbsc3 = 0xb00a; |
| mbfs0 = 0x00; |
| mbfs1 = 0x00; |
| mbfs2 = 0x1e; |
| |
| if (dimm03 > 2) { |
| mbsc1 |= 0x003c; |
| mbfs2 |= 0x40; |
| } else { |
| mbsc3 |= 0xc000; |
| } |
| if ((dimm03 + dimm47) > 4) { |
| mbsc0 |= 0x30; |
| mbfs0 |= 0x02; |
| } |
| } |
| |
| pci_write_config8(NB, MBSC + 0, mbsc0); |
| pci_write_config16(NB, MBSC + 1, mbsc1); |
| pci_write_config16(NB, MBSC + 3, mbsc3); |
| pci_write_config16(NB, MBFS + 0, mbfs1 << 8 | mbfs0); |
| pci_write_config8(NB, MBFS + 2, mbfs2); |
| } |
| |
| /*----------------------------------------------------------------------------- |
| DIMM-independent configuration functions. |
| -----------------------------------------------------------------------------*/ |
| |
| static void spd_enable_refresh(void) |
| { |
| int i, value; |
| uint8_t reg; |
| |
| reg = pci_read_config8(NB, DRAMC); |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| value = spd_read_byte(DIMM0 + i, SPD_REFRESH); |
| if (value < 0) |
| continue; |
| reg = (reg & 0xf8) | refresh_rate_map[(value & 0x7f)]; |
| |
| PRINT_DEBUG(" Enabling refresh (DRAMC = 0x%02x) for DIMM %02x\n", reg, i); |
| } |
| |
| pci_write_config8(NB, DRAMC, reg); |
| } |
| |
| /*----------------------------------------------------------------------------- |
| Public interface. |
| -----------------------------------------------------------------------------*/ |
| |
| void sdram_set_registers(void) |
| { |
| int i, max; |
| uint8_t reg; |
| |
| PRINT_DEBUG("Northbridge prior to SDRAM init:\n"); |
| DUMPNORTH(); |
| |
| max = ARRAY_SIZE(register_values); |
| |
| /* Set registers as specified in the register_values[] array. */ |
| for (i = 0; i < max; i += 3) { |
| reg = pci_read_config8(NB, register_values[i]); |
| reg &= register_values[i + 1]; |
| reg |= register_values[i + 2] & ~(register_values[i + 1]); |
| pci_write_config8(NB, register_values[i], reg); |
| } |
| } |
| |
| struct dimm_size { |
| u32 side1; |
| u32 side2; |
| }; |
| |
| static struct dimm_size spd_get_dimm_size(unsigned int device) |
| { |
| struct dimm_size sz; |
| int i, module_density, dimm_banks; |
| sz.side1 = 0; |
| module_density = spd_read_byte(device, SPD_DENSITY_OF_EACH_ROW_ON_MODULE); |
| dimm_banks = spd_read_byte(device, SPD_NUM_DIMM_BANKS); |
| |
| /* Find the size of side1. */ |
| /* Find the larger value. The larger value is always side1. */ |
| for (i = 512; i >= 0; i >>= 1) { |
| if ((module_density & i) == i) { |
| sz.side1 = i; |
| break; |
| } |
| } |
| |
| /* Set to 0 in case it's single sided. */ |
| sz.side2 = 0; |
| |
| /* Test if it's a dual-sided DIMM. */ |
| if (dimm_banks > 1) { |
| /* Test if there's a second value. If so it's asymmetrical. */ |
| if (module_density != i) { |
| /* |
| * Find second value, picking up where we left off. |
| * i >>= 1 done initially to make sure we don't get |
| * the same value again. |
| */ |
| for (i >>= 1; i >= 0; i >>= 1) { |
| if (module_density == (sz.side1 | i)) { |
| sz.side2 = i; |
| break; |
| } |
| } |
| /* If not, it's symmetrical. */ |
| } else { |
| sz.side2 = sz.side1; |
| } |
| } |
| |
| /* |
| * SPD byte 31 is the memory size divided by 4 so we |
| * need to multiply by 4 to get the total size. |
| */ |
| sz.side1 *= 4; |
| sz.side2 *= 4; |
| |
| /* |
| * It is possible to partially use larger than supported |
| * modules by setting them to a supported size. |
| */ |
| if (sz.side1 > 128) { |
| PRINT_DEBUG("Side1 was %dMB but only 128MB will be used.\n", |
| sz.side1); |
| sz.side1 = 128; |
| |
| if (sz.side2 > 128) { |
| PRINT_DEBUG("Side2 was %dMB but only 128MB will be used.\n", |
| sz.side2); |
| sz.side2 = 128; |
| } |
| } |
| |
| return sz; |
| } |
| /* |
| * Sets DRAM attributes one DIMM at a time, based on SPD data. |
| * Northbridge settings that are set: NBXCFG[31:24], DRB0-DRB7, RPS, DRAMC. |
| */ |
| static void set_dram_row_attributes(void) |
| { |
| int i, dra, drb, col, width, value, rps; |
| u8 bpr; /* Top 8 bits of PGPOL */ |
| u8 nbxecc = 0; /* NBXCFG[31:24] */ |
| u8 edo, sd, regsd; /* EDO, SDRAM, registered SDRAM */ |
| |
| edo = 0; |
| sd = 0; |
| regsd = 1; |
| rps = 0; |
| drb = 0; |
| bpr = 0; |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| unsigned int device; |
| device = DIMM0 + i; |
| bpr >>= 2; |
| nbxecc >>= 2; |
| |
| /* First check if a DIMM is actually present. */ |
| value = spd_read_byte(device, SPD_MEMORY_TYPE); |
| /* This is 440BX! We do EDO too! */ |
| if (value == SPD_MEMORY_TYPE_EDO |
| || value == SPD_MEMORY_TYPE_SDRAM) { |
| |
| if (value == SPD_MEMORY_TYPE_EDO) { |
| edo = 1; |
| } else if (value == SPD_MEMORY_TYPE_SDRAM) { |
| sd = 1; |
| } |
| PRINT_DEBUG("Found DIMM in slot %d\n", i); |
| |
| if (edo && sd) { |
| printk(BIOS_ERR, "Mixing EDO/SDRAM unsupported!\n"); |
| die("HALT\n"); |
| } |
| |
| /* "DRA" is our RPS for the two rows on this DIMM. */ |
| dra = 0; |
| |
| /* Columns */ |
| col = spd_read_byte(device, SPD_NUM_COLUMNS); |
| |
| /* |
| * Is this an ECC DIMM? Actually will be a 2 if so. |
| * TODO: Other register than NBXCFG also needs this |
| * ECC information. |
| */ |
| value = spd_read_byte(device, SPD_DIMM_CONFIG_TYPE); |
| |
| /* Data width */ |
| width = spd_read_byte(device, SPD_MODULE_DATA_WIDTH_LSB); |
| |
| /* Exclude error checking data width from page size calculations */ |
| if (value) { |
| value = spd_read_byte(device, |
| SPD_ERROR_CHECKING_SDRAM_WIDTH); |
| width -= value; |
| /* ### ECC */ |
| /* Clear top 2 bits to help set up NBXCFG. */ |
| nbxecc &= 0x3f; |
| } else { |
| /* Without ECC, top 2 bits should be 11. */ |
| nbxecc |= 0xc0; |
| } |
| |
| /* If any installed DIMM is *not* registered, this system cannot be |
| * configured for registered SDRAM. |
| * By registered, only the address and control lines need to be, which |
| * we can tell by reading SPD byte 21, bit 1. |
| */ |
| value = spd_read_byte(device, SPD_MODULE_ATTRIBUTES); |
| |
| PRINT_DEBUG("DIMM is "); |
| if ((value & MODULE_REGISTERED) == 0) { |
| regsd = 0; |
| PRINT_DEBUG("not "); |
| } |
| PRINT_DEBUG("registered\n"); |
| |
| /* Calculate page size in bits. */ |
| value = ((1 << col) * width); |
| |
| /* Convert to KB. */ |
| dra = (value >> 13); |
| |
| /* Number of banks of DIMM (single or double sided). */ |
| value = spd_read_byte(device, SPD_NUM_DIMM_BANKS); |
| |
| /* Once we have dra, col is done and can be reused. |
| * So it's reused for number of banks. |
| */ |
| col = spd_read_byte(device, SPD_NUM_BANKS_PER_SDRAM); |
| |
| if (value == 1) { |
| /* |
| * Second bank of 1-bank DIMMs "doesn't have |
| * ECC" - or anything. |
| */ |
| if (dra == 2) { |
| dra = 0x0; /* 2KB */ |
| } else if (dra == 4) { |
| dra = 0x1; /* 4KB */ |
| } else if (dra == 8) { |
| dra = 0x2; /* 8KB */ |
| } else if (dra >= 16) { |
| /* Page sizes larger than supported are |
| * set to 8KB to use module partially. |
| */ |
| PRINT_DEBUG("Page size forced to 8KB.\n"); |
| dra = 0x2; /* 8KB */ |
| } else { |
| dra = -1; |
| } |
| /* |
| * Sets a flag in PGPOL[BPR] if this DIMM has |
| * 4 banks per row. |
| */ |
| if (col == 4) |
| bpr |= 0x40; |
| } else if (value == 2) { |
| if (dra == 2) { |
| dra = 0x0; /* 2KB */ |
| } else if (dra == 4) { |
| dra = 0x05; /* 4KB */ |
| } else if (dra == 8) { |
| dra = 0x0a; /* 8KB */ |
| } else if (dra >= 16) { |
| /* Ditto */ |
| PRINT_DEBUG("Page size forced to 8KB.\n"); |
| dra = 0x0a; /* 8KB */ |
| } else { |
| dra = -1; |
| } |
| /* Ditto */ |
| if (col == 4) |
| bpr |= 0xc0; |
| } else { |
| printk(BIOS_ERR, "# of banks of DIMM unsupported!\n"); |
| die("HALT\n"); |
| } |
| if (dra == -1) { |
| printk(BIOS_ERR, "Page size not supported\n"); |
| die("HALT\n"); |
| } |
| |
| /* |
| * 440BX supports asymmetrical dual-sided DIMMs, |
| * but can't handle DIMMs smaller than 8MB per |
| * side. |
| */ |
| struct dimm_size sz = spd_get_dimm_size(device); |
| if ((sz.side1 < 8)) { |
| printk(BIOS_ERR, "DIMMs smaller than 8MB per side\n" |
| "are not supported on this NB.\n"); |
| die("HALT\n"); |
| } |
| |
| /* Divide size by 8 to set up the DRB registers. */ |
| drb += (sz.side1 / 8); |
| |
| /* |
| * Build the DRB for the next row in MSB so it gets |
| * placed in DRB[n+1] where it belongs when written |
| * as a 16-bit word. |
| */ |
| drb &= 0xff; |
| drb |= (drb + (sz.side2 / 8)) << 8; |
| } else { |
| /* If there's no DIMM in the slot, set dra to 0x00. */ |
| dra = 0x00; |
| /* Still have to propagate DRB over. */ |
| drb &= 0xff; |
| drb |= (drb << 8); |
| } |
| |
| pci_write_config16(NB, DRB + (2 * i), drb); |
| |
| /* Brings the upper DRB back down to be base for |
| * DRB calculations for the next two rows. |
| */ |
| drb >>= 8; |
| |
| rps |= (dra & 0x0f) << (i * 4); |
| } |
| |
| /* Set paging policy register. */ |
| pci_write_config8(NB, PGPOL + 1, bpr); |
| PRINT_DEBUG("PGPOL[BPR] has been set to 0x%02x\n", bpr); |
| |
| /* Set DRAM row page size register. */ |
| pci_write_config16(NB, RPS, rps); |
| PRINT_DEBUG("RPS has been set to 0x%04x\n", rps); |
| |
| /* ### ECC */ |
| pci_write_config8(NB, NBXCFG + 3, nbxecc); |
| PRINT_DEBUG("NBXECC[31:24] has been set to 0x%02x\n", nbxecc); |
| |
| /* Set DRAMC[4:3] to proper memory type (EDO/SDRAM/Registered SDRAM). */ |
| |
| /* i will be used to set DRAMC[4:3]. */ |
| if (regsd && sd) { |
| i = 0x10; // Registered SDRAM |
| } else if (sd) { |
| i = 0x08; // SDRAM |
| } else { |
| i = 0; // EDO |
| } |
| |
| value = pci_read_config8(NB, DRAMC) & 0xe7; |
| value |= i; |
| pci_write_config8(NB, DRAMC, value); |
| PRINT_DEBUG("DRAMC has been set to 0x%02x\n", value); |
| } |
| |
| void sdram_set_spd_registers(void) |
| { |
| /* Setup DRAM row boundary registers and other attributes. */ |
| set_dram_row_attributes(); |
| |
| /* Setup DRAM buffer strength. */ |
| set_dram_buffer_strength(); |
| |
| /* TODO: Set PMCR? */ |
| // pci_write_config8(NB, PMCR, 0x14); |
| pci_write_config8(NB, PMCR, 0x10); |
| |
| /* TODO: This is for EDO memory only. */ |
| pci_write_config8(NB, DRAMT, 0x03); |
| } |
| |
| void sdram_enable(void) |
| { |
| int i; |
| |
| /* 0. Wait until power/voltages and clocks are stable (200us). */ |
| udelay(200); |
| |
| /* 1. Apply NOP. Wait 200 clock cycles (200us should do). */ |
| PRINT_DEBUG("RAM Enable 1: Apply NOP\n"); |
| do_ram_command(RAM_COMMAND_NOP); |
| udelay(200); |
| |
| /* 2. Precharge all. Wait tRP. */ |
| PRINT_DEBUG("RAM Enable 2: Precharge all\n"); |
| do_ram_command(RAM_COMMAND_PRECHARGE); |
| udelay(1); |
| |
| /* 3. Perform 8 refresh cycles. Wait tRC each time. */ |
| PRINT_DEBUG("RAM Enable 3: CBR\n"); |
| for (i = 0; i < 8; i++) { |
| do_ram_command(RAM_COMMAND_CBR); |
| udelay(1); |
| } |
| |
| /* 4. Mode register set. Wait two memory cycles. */ |
| PRINT_DEBUG("RAM Enable 4: Mode register set\n"); |
| do_ram_command(RAM_COMMAND_MRS); |
| udelay(2); |
| |
| /* 5. Normal operation. */ |
| PRINT_DEBUG("RAM Enable 5: Normal operation\n"); |
| do_ram_command(RAM_COMMAND_NORMAL); |
| udelay(1); |
| |
| /* 6. Finally enable refresh. */ |
| PRINT_DEBUG("RAM Enable 6: Enable refresh\n"); |
| // pci_write_config8(NB, PMCR, 0x10); |
| spd_enable_refresh(); |
| udelay(1); |
| |
| PRINT_DEBUG("Northbridge following SDRAM init:\n"); |
| DUMPNORTH(); |
| } |
| |
| void sdram_initialize(void) |
| { |
| dump_spd_registers(); |
| sdram_set_registers(); |
| sdram_set_spd_registers(); |
| sdram_enable(); |
| } |