| ## SPDX-License-Identifier: GPL-2.0-only |
| |
| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx.ndid" = "4" |
| register "gfx.did" = "{ 0x80000400, 0x80000300, 0x80000301, 0x80000100, }" |
| |
| # Enable Panel as eDP and configure power delays |
| register "gpu_panel_port_select" = "PANEL_PORT_DP_A" |
| register "gpu_panel_power_cycle_delay" = "6" # 500ms |
| register "gpu_panel_power_up_delay" = "2000" # 200ms |
| register "gpu_panel_power_down_delay" = "500" # 50ms |
| register "gpu_panel_power_backlight_on_delay" = "1" # 100us as recommended by PRM |
| register "gpu_panel_power_backlight_off_delay" = "2000" # 200ms |
| |
| # Set backlight PWM values for eDP |
| register "gpu_cpu_backlight" = "0x00000ac8" |
| register "gpu_pch_backlight" = "0x13120000" |
| |
| register "spd_addresses" = "{0x50, 0x51, 0x52, 0x53}" |
| register "ec_present" = "1" |
| register "max_mem_clock_mhz" = "800" |
| |
| register "usb3.mode" = "3" |
| register "usb3.hs_port_switch_mask" = "0xf" |
| register "usb3.preboot_support" = "1" |
| register "usb3.xhci_streams" = "1" |
| register "usb_port_config" = "{ |
| { 1, 0, 0x0080 }, |
| { 1, 0, 0x0080 }, |
| { 1, 1, 0x0080 }, |
| { 1, 1, 0x0080 }, |
| { 1, 8, 0x0040 }, |
| { 1, 8, 0x0040 }, |
| { 1, 8, 0x0040 }, |
| { 1, 8, 0x0040 }, |
| { 1, 8, 0x0080 }, |
| { 1, 4, 0x0080 }, |
| { 1, 5, 0x0040 }, |
| { 1, 8, 0x0040 }, |
| { 1, 8, 0x0080 }, |
| { 1, 6, 0x0080 }, }" |
| |
| chip cpu/intel/model_206ax |
| device cpu_cluster 0 on end |
| |
| register "acpi_c2" = "CPU_ACPI_C6" |
| register "acpi_c3" = "CPU_ACPI_DISABLED" |
| end |
| |
| device domain 0 on |
| device ref host_bridge on end # host bridge |
| device ref igd on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # LPC i/o generic decodes |
| register "gen1_dec" = "0x003c0a01" # ITE environment controller |
| register "gen2_dec" = "0x000403e9" # additional com port |
| register "gen3_dec" = "0x000402e9" # additional com port |
| |
| # Enable both SATA ports 0, 1 |
| register "sata_port_map" = "0x03" |
| # Set max SATA speed to 6.0 Gb/s (should be the default, anyway) |
| register "sata_interface_speed_support" = "0x3" |
| |
| # Route GPI7 (EC SCI) as SCI |
| register "gpi7_routing" = "2" |
| |
| # Enable GPE17 (GPI7) and TCO SCI |
| register "gpe0_en" = "0x00800040" |
| |
| # Disable root port coalescing |
| register "pcie_port_coalesce" = "false" |
| register "pcie_hotplug_map" = "{ 0, 0, 0, 0, 0, 0, 1, 1 }" |
| |
| |
| register "xhci_overcurrent_mapping" = "0x00000c03" |
| register "xhci_switchable_ports" = "0x0f" |
| register "superspeed_capable_ports" = "0x0f" |
| |
| register "spi_uvscc" = "0x2005" |
| register "spi_lvscc" = "0x2005" |
| |
| device ref xhci on end # USB 3.0 Controller |
| device ref mei1 on end # Management Engine Interface 1 |
| device ref mei2 off end # Management Engine Interface 2 |
| device ref me_ide_r off end # Management Engine IDE-R |
| device ref me_kt off end # Management Engine KT |
| device ref gbe on end # Intel Gigabit Ethernet |
| device ref ehci2 on end # USB2 EHCI #2 |
| device ref hda on # High Definition Audio |
| subsystemid 0x1a86 0x4352 |
| end |
| |
| # Disabling 1c.0 might break IRQ settings as it enables port coalescing |
| device ref pcie_rp1 on end # PCIe Port #1 |
| device ref pcie_rp2 on end # PCIe Port #2 |
| device ref pcie_rp3 on end # PCIe Port #3 |
| device ref pcie_rp4 on end # PCIe Port #4 |
| device ref pcie_rp5 on end # PCIe Port #5 |
| device ref pcie_rp6 on end # PCIe Port #6 |
| device ref pcie_rp7 on end # PCIe Port #7 |
| device ref pcie_rp8 on end # PCIe Port #8 |
| |
| device ref ehci1 on end # USB2 EHCI #1 |
| device ref pci_bridge off end # PCI bridge |
| device ref lpc on # LPC bridge |
| chip ec/roda/it8518 |
| register "cpuhot_limit" = "100" |
| # 60h/64h KBC |
| device pnp ff.0 on # dummy address |
| end |
| end |
| chip superio/ite/it8783ef |
| register "TMPIN1.mode" = "THERMAL_RESISTOR" |
| register "TMPIN2.mode" = "THERMAL_RESISTOR" |
| register "ec.vin_mask" = "VIN_ALL" |
| register "FAN1.mode" = "FAN_SMART_AUTOMATIC" |
| register "FAN1.smart.tmpin" = " 1" |
| register "FAN1.smart.tmp_off" = "60" |
| register "FAN1.smart.tmp_start" = "64" |
| register "FAN1.smart.tmp_delta" = " 2" |
| register "FAN1.smart.pwm_start" = "30" |
| register "FAN1.smart.slope" = "64" |
| register "FAN2.mode" = "FAN_SMART_AUTOMATIC" |
| register "FAN2.smart.tmpin" = " 1" |
| register "FAN2.smart.tmp_off" = "60" |
| register "FAN2.smart.tmp_start" = "64" |
| register "FAN2.smart.tmp_delta" = " 2" |
| register "FAN2.smart.pwm_start" = "30" |
| register "FAN2.smart.slope" = "64" |
| register "FAN3.mode" = "FAN_MODE_OFF" |
| device pnp 2e.0 off end # Floppy |
| device pnp 2e.1 on # COM 1 |
| io 0x60 = 0x3f8 |
| irq 0x70 = 4 |
| end |
| device pnp 2e.2 on # COM 2 |
| io 0x60 = 0x2f8 |
| irq 0x70 = 3 |
| end |
| device pnp 2e.3 on # Printer Port |
| io 0x60 = 0x378 |
| io 0x62 = 0x000 |
| irq 0x70 = 7 |
| drq 0x74 = 4 |
| irq 0xf0 = 0x00 |
| end |
| device pnp 2e.4 on # Environment Controller |
| io 0x60 = 0xa30 |
| io 0x62 = 0xa20 |
| irq 0x70 = 0 |
| irq 0xf0 = 0x80 |
| end |
| device pnp 2e.5 off end # Keyboard |
| device pnp 2e.6 off end # Mouse |
| device pnp 2e.7 off end # GPIO |
| device pnp 2e.8 on # COM 3 |
| io 0x60 = 0x3e8 |
| irq 0x70 = 4 |
| end |
| device pnp 2e.9 on # COM 4 |
| io 0x60 = 0x2e8 |
| irq 0x70 = 3 |
| end |
| device pnp 2e.a off end # COM 5 |
| device pnp 2e.b off end # COM 6 |
| device pnp 2e.c off end # CIR |
| end |
| end # LPC bridge |
| device ref sata1 on end # SATA Controller 1 |
| device ref smbus on end # SMBus |
| device ref sata2 off end # SATA Controller 2 |
| device ref thermal off end # Thermal |
| end |
| end |
| end |