| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx" = "GMA_STATIC_DISPLAYS(0)" |
| |
| # Enable DisplayPort Hotplug with 6ms pulse |
| register "gpu_dp_d_hotplug" = "0x06" |
| |
| |
| # Enable Panel as LVDS and configure power delays |
| register "gpu_panel_port_select" = "PANEL_PORT_LVDS" |
| register "gpu_panel_power_cycle_delay" = "6" # T7: 500ms |
| register "gpu_panel_power_up_delay" = "100" # T1+T2: 10ms |
| register "gpu_panel_power_down_delay" = "100" # T5+T6: 10ms |
| register "gpu_panel_power_backlight_on_delay" = "2100" # T3: 210ms |
| register "gpu_panel_power_backlight_off_delay" = "2100" # T4: 210ms |
| |
| # Set backlight PWM values |
| register "gpu_cpu_backlight" = "0x000001e8" |
| register "gpu_pch_backlight" = "0x03d00000" |
| |
| register "spd_addresses" = "{0x50, 0, 0x52, 0}" |
| register "ec_present" = "1" |
| # FIXME: Native raminit requires reduced max clock |
| register "max_mem_clock_mhz" = "CONFIG(USE_NATIVE_RAMINIT) ? 666 : 800" |
| # Force double refresh rate |
| register "ddr_refresh_rate_config" = "DDR_REFRESH_RATE_DOUBLE" |
| |
| register "usb_port_config" = "{ |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 0, 0, 0x0000 }, |
| { 0, 0, 0x0000 }, |
| { 0, 0, 0x0000 }, |
| { 0, 0, 0x0000 }, |
| { 0, 0, 0x0000 }, |
| { 0, 4, 0x0000 }, |
| { 1, 4, 0x0080 }, |
| { 1, 4, 0x0040 }, |
| { 0, 4, 0x0000 }, |
| { 0, 4, 0x0000 }, |
| { 0, 4, 0x0000 },}" |
| |
| device domain 0 on |
| device ref host_bridge on end # host bridge |
| device ref peg10 off end # PCIe Bridge for discrete graphics |
| device ref igd on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # GPI routing |
| # 0 No effect (default) |
| # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) |
| # 2 SCI (if corresponding GPIO_EN bit is also set) |
| register "alt_gp_smi_en" = "0x0000" |
| #register "gpi1_routing" = "1" #SMI from EC |
| register "gpi13_routing" = "2" #SCI from EC |
| |
| # Enable SATA ports 0 & 1 |
| register "sata_port_map" = "0x3" |
| # Set max SATA speed to 3.0 Gb/s |
| register "sata_interface_speed_support" = "0x2" |
| |
| # Enable EC Port 0x68/0x6C |
| register "gen1_dec" = "0x00040069" |
| |
| # EC range is 0x380-0387 |
| register "gen2_dec" = "0x00040381" |
| |
| # Enable zero-based linear PCIe root port functions |
| register "pcie_port_coalesce" = "true" |
| |
| device ref xhci on end # USB 3.0 Controller |
| device ref mei1 on end # Management Engine Interface 1 |
| device ref mei2 off end # Management Engine Interface 2 |
| device ref me_ide_r off end # Management Engine IDE-R |
| device ref me_kt off end # Management Engine KT |
| device ref gbe off end # Intel Gigabit Ethernet |
| device ref ehci2 on end # USB2 EHCI #2 |
| device ref hda on end # High Definition Audio |
| device ref pcie_rp1 on end # PCIe Port #1 (mini PCIe Slot - WLAN & Serial debug) |
| device ref pcie_rp2 on end # PCIe Port #2 (ETH0) |
| device ref pcie_rp3 on end # PCIe Port #3 (Card Reader) |
| #force ASPM for PCIe bridge to Card Reader |
| register "pcie_aspm[2]" = "0x3" |
| device ref pcie_rp4 off end # PCIe Port #4 |
| device ref pcie_rp5 off end # PCIe Port #5 |
| device ref pcie_rp6 off end # PCIe Port #6 |
| device ref pcie_rp7 off end # PCIe Port #7 |
| device ref pcie_rp8 off end # PCIe Port #8 |
| device ref ehci1 on end # USB2 EHCI #1 |
| device ref pci_bridge off end # PCI bridge |
| device ref lpc on #LPC bridge |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| chip ec/quanta/ene_kb3940q |
| # 60/64 KBC |
| device pnp ff.1 on # dummy address |
| end |
| end |
| end # LPC bridge |
| device ref sata1 on end # SATA Controller 1 |
| device ref smbus on |
| subsystemid 0x18D1 0x04B4 |
| end # SMBus |
| device ref sata2 off end # SATA Controller 2 |
| device ref thermal on end # Thermal |
| end |
| end |
| end |