| fw_config |
| field THERMAL_SOLUTION 0 0 |
| option THERMAL_SOLUTION_6W 0 |
| option THERMAL_SOLUTION_15W 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. |
| # Bit 2 - C1 has a redriver which does SBU muxing. |
| # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. |
| register "tcss_aux_ori" = "1" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| |
| # Configure external V1P05/Vnn/VnnSx Rails |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, |
| .v1p05_voltage_mv = 1050, |
| .vnn_voltage_mv = 780, |
| .vnn_sx_voltage_mv = 1050, |
| .v1p05_icc_max_ma = 500, |
| .vnn_icc_max_ma = 500, |
| }" |
| |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| }" |
| |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2 Port 2 |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 5 |
| register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 7 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| register "tcc_offset" = "8" |
| |
| register "power_limits_config[ADL_N_041_6W_CORE]" = "{ |
| .tdp_pl1_override = 20, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| register "power_limits_config[ADL_N_081_15W_CORE]" = "{ |
| .tdp_pl1_override = 20, |
| .tdp_pl2_override = 35, |
| .tdp_pl4 = 83, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DDR"" |
| register "options.tsr[1].desc" = ""charger"" |
| register "options.tsr[2].desc" = ""ambient"" |
| |
| ## Active Policy |
| register "policies.active" = "{ |
| [0] = { |
| .target = DPTF_CPU, |
| .thresholds = { |
| TEMP_PCT(70, 100), |
| TEMP_PCT(60, 65), |
| TEMP_PCT(42, 60), |
| TEMP_PCT(39, 55), |
| TEMP_PCT(38, 50), |
| TEMP_PCT(35, 43), |
| TEMP_PCT(31, 30), |
| } |
| }, |
| [1] = { |
| .target = DPTF_TEMP_SENSOR_0, |
| .thresholds = { |
| TEMP_PCT(60, 100), |
| TEMP_PCT(55, 65), |
| TEMP_PCT(52, 60), |
| TEMP_PCT(50, 55), |
| TEMP_PCT(48, 50), |
| TEMP_PCT(45, 43), |
| TEMP_PCT(41, 30), |
| } |
| } |
| }" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 70, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 70, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 6000, |
| .max_power = 20000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 500 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 32 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 500 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 100, 6000, 220, 2200, }, |
| [1] = { 92, 5500, 180, 1800, }, |
| [2] = { 85, 5000, 145, 1450, }, |
| [3] = { 70, 4400, 115, 1150, }, |
| [4] = { 56, 3900, 90, 900, }, |
| [5] = { 45, 3300, 55, 550, }, |
| [6] = { 38, 3000, 30, 300, }, |
| [7] = { 33, 2900, 15, 150, }, |
| [8] = { 10, 800, 10, 100, }, |
| [9] = { 0, 0, 0, 50, } |
| }" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 0 on |
| probe THERMAL_SOLUTION THERMAL_SOLUTION_6W |
| end |
| end |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DDR"" |
| register "options.tsr[1].desc" = ""charger"" |
| register "options.tsr[2].desc" = ""ambient"" |
| |
| ## Active Policy |
| register "policies.active" = "{ |
| [0] = { |
| .target = DPTF_CPU, |
| .thresholds = { |
| TEMP_PCT(70, 100), |
| TEMP_PCT(60, 65), |
| TEMP_PCT(42, 58), |
| TEMP_PCT(39, 53), |
| TEMP_PCT(38, 47), |
| TEMP_PCT(35, 43), |
| TEMP_PCT(31, 30), |
| } |
| }, |
| [1] = { |
| .target = DPTF_TEMP_SENSOR_0, |
| .thresholds = { |
| TEMP_PCT(60, 100), |
| TEMP_PCT(55, 65), |
| TEMP_PCT(52, 58), |
| TEMP_PCT(50, 53), |
| TEMP_PCT(48, 47), |
| TEMP_PCT(45, 43), |
| TEMP_PCT(41, 30), |
| } |
| } |
| }" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 70, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 70, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 15000, |
| .max_power = 20000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 500 |
| }, |
| .pl2 = { |
| .min_power = 35000, |
| .max_power = 35000, |
| .time_window_min = 32 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 500 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 100, 6000, 220, 2200, }, |
| [1] = { 92, 5500, 180, 1800, }, |
| [2] = { 85, 5000, 145, 1450, }, |
| [3] = { 70, 4400, 115, 1150, }, |
| [4] = { 56, 3900, 90, 900, }, |
| [5] = { 45, 3300, 55, 550, }, |
| [6] = { 38, 3000, 30, 300, }, |
| [7] = { 33, 2900, 15, 150, }, |
| [8] = { 10, 800, 10, 100, }, |
| [9] = { 0, 0, 0, 50, } |
| }" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 1 on |
| probe THERMAL_SOLUTION THERMAL_SOLUTION_15W |
| end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9004"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_delay_ms" = "150" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end #I2C1 |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5650"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5650"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-mode"" |
| register "property_list[0].integer" = "2" |
| device i2c 1a on end |
| end |
| end #I2C3 |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0000"" |
| register "generic.cid" = ""ACPI0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PIXA2303"" |
| register "generic.desc" = ""PIXA Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x68 on end |
| end |
| end |
| device ref pcie_rp7 off end |
| device ref emmc on end |
| device ref ish on |
| chip drivers/intel/ish |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref ufs on end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| register "enable_cnvi_ddr_rfim" = "true" |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref hda on |
| chip drivers/sof |
| register "spkr_tplg" = "rt5650_sp" |
| register "jack_tplg" = "rt5650_hp" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on end |
| end |
| end |
| end |
| |
| end |