| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2010 coresystems GmbH |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| // __PRE_RAM__ means: use "unsigned" for device, not a struct. |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <lib.h> |
| #include <cbmem.h> |
| #include <arch/io.h> |
| #include <device/pci_def.h> |
| #include <device/pnp_def.h> |
| #include <cpu/x86/lapic.h> |
| #include <pc80/mc146818rtc.h> |
| #include "option_table.h" |
| #include <console/console.h> |
| #include <cpu/x86/bist.h> |
| #include <superio/winbond/w83627thg/w83627thg.h> |
| #include "northbridge/intel/i945/i945.h" |
| #include "northbridge/intel/i945/raminit.h" |
| #include "southbridge/intel/i82801gx/i82801gx.h" |
| |
| #define SERIAL_DEV PNP_DEV(0x2e, W83627THG_SP1) |
| |
| void setup_ich7_gpios(void) |
| { |
| printk(BIOS_DEBUG, " GPIOS..."); |
| /* General Registers */ |
| outl(0x1f1ff7c0, DEFAULT_GPIOBASE + 0x00); /* GPIO_USE_SEL */ |
| outl(0xe0e8efc3, DEFAULT_GPIOBASE + 0x04); /* GP_IO_SEL */ |
| outl(0xebffeeff, DEFAULT_GPIOBASE + 0x0c); /* GP_LVL */ |
| /* Output Control Registers */ |
| outl(0x00000000, DEFAULT_GPIOBASE + 0x18); /* GPO_BLINK */ |
| /* Input Control Registers */ |
| outl(0x00002180, DEFAULT_GPIOBASE + 0x2c); /* GPI_INV */ |
| outl(0x000100ff, DEFAULT_GPIOBASE + 0x30); /* GPIO_USE_SEL2 */ |
| outl(0x00000030, DEFAULT_GPIOBASE + 0x34); /* GP_IO_SEL2 */ |
| outl(0x00010035, DEFAULT_GPIOBASE + 0x38); /* GP_LVL */ |
| } |
| |
| static void ich7_enable_lpc(void) |
| { |
| int lpt_en = 0; |
| if (read_option(lpt, 0) != 0) { |
| lpt_en = 1<<2; // enable LPT |
| } |
| // Enable Serial IRQ |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x64, 0xd0); |
| // Set COM1/COM2 decode range |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0010); |
| // Enable COM1/COM2/KBD/SuperIO1+2 |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x340b | lpt_en); |
| // Enable HWM at 0xa00 |
| pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x84, 0x00fc0a01); |
| // COM3 decode |
| pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x88, 0x000403e9); |
| // COM4 decode |
| pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x8c, 0x000402e9); |
| // io 0x300 decode |
| pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x90, 0x00000301); |
| } |
| |
| /* This box has two superios, so enabling serial becomes slightly excessive. |
| * We disable a lot of stuff to make sure that there are no conflicts between |
| * the two. Also set up the GPIOs from the beginning. This is the "no schematic |
| * but safe anyways" method. |
| */ |
| static void early_superio_config_w83627thg(void) |
| { |
| device_t dev; |
| |
| dev=PNP_DEV(0x2e, W83627THG_SP1); |
| pnp_enter_ext_func_mode(dev); |
| |
| pnp_write_config(dev, 0x24, 0xc6); // PNPCSV |
| |
| pnp_write_config(dev, 0x29, 0x43); // GPIO settings |
| pnp_write_config(dev, 0x2a, 0x40); // GPIO settings |
| |
| dev=PNP_DEV(0x2e, W83627THG_SP1); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x3f8); |
| pnp_set_irq(dev, PNP_IDX_IRQ0, 4); |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x2e, W83627THG_SP2); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x2f8); |
| pnp_set_irq(dev, PNP_IDX_IRQ0, 3); |
| // pnp_write_config(dev, 0xf1, 4); // IRMODE0 |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x2e, W83627THG_KBC); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x60); |
| pnp_set_iobase(dev, PNP_IDX_IO1, 0x64); |
| // pnp_write_config(dev, 0xf0, 0x82); |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x2e, W83627THG_GAME_MIDI_GPIO1); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_write_config(dev, 0xf5, 0xff); // invert all GPIOs |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x2e, W83627THG_GPIO2); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 1); // Just enable it |
| |
| dev=PNP_DEV(0x2e, W83627THG_GPIO3); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_write_config(dev, 0xf0, 0xfb); // GPIO bit 2 is output |
| pnp_write_config(dev, 0xf1, 0x00); // GPIO bit 2 is 0 |
| pnp_write_config(dev, 0x30, 0x03); // Enable GPIO3+4. pnp_set_enable is not sufficient |
| |
| dev=PNP_DEV(0x2e, W83627THG_FDC); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| |
| dev=PNP_DEV(0x2e, W83627THG_PP); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| |
| /* Enable HWM */ |
| dev=PNP_DEV(0x2e, W83627THG_HWM); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0xa00); |
| pnp_set_enable(dev, 1); |
| |
| pnp_exit_ext_func_mode(dev); |
| |
| dev=PNP_DEV(0x4e, W83627THG_SP1); |
| pnp_enter_ext_func_mode(dev); |
| |
| pnp_set_logical_device(dev); // Set COM3 to sane non-conflicting values |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x3e8); |
| pnp_set_irq(dev, PNP_IDX_IRQ0, 11); |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x4e, W83627THG_SP2); |
| pnp_set_logical_device(dev); // Set COM4 to sane non-conflicting values |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x2e8); |
| pnp_set_irq(dev, PNP_IDX_IRQ0, 10); |
| pnp_set_enable(dev, 1); |
| |
| dev=PNP_DEV(0x4e, W83627THG_FDC); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| |
| dev=PNP_DEV(0x4e, W83627THG_PP); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| |
| dev=PNP_DEV(0x4e, W83627THG_KBC); |
| pnp_set_logical_device(dev); |
| pnp_set_enable(dev, 0); |
| pnp_set_iobase(dev, PNP_IDX_IO0, 0x00); |
| pnp_set_iobase(dev, PNP_IDX_IO1, 0x00); |
| |
| pnp_exit_ext_func_mode(dev); |
| } |
| |
| static void rcba_config(void) |
| { |
| u32 reg32; |
| |
| /* Set up virtual channel 0 */ |
| //RCBA32(0x0014) = 0x80000001; |
| //RCBA32(0x001c) = 0x03128010; |
| |
| /* Device 1f interrupt pin register */ |
| RCBA32(0x3100) = 0x00042210; |
| /* Device 1d interrupt pin register */ |
| RCBA32(0x310c) = 0x00214321; |
| |
| /* dev irq route register */ |
| RCBA16(0x3140) = 0x0132; |
| RCBA16(0x3142) = 0x3241; |
| RCBA16(0x3144) = 0x0237; |
| RCBA16(0x3146) = 0x3210; |
| RCBA16(0x3148) = 0x3210; |
| |
| /* Enable IOAPIC */ |
| RCBA8(0x31ff) = 0x03; |
| |
| /* Enable upper 128bytes of CMOS */ |
| RCBA32(0x3400) = (1 << 2); |
| |
| /* Now, this is a bit ugly. As per PCI specification, function 0 of a |
| * device always has to be implemented. So disabling ethernet port 1 |
| * would essentially disable all three ethernet ports of the mainboard. |
| * It's possible to rename the ports to achieve compatibility to the |
| * PCI spec but this will confuse all (static!) tables containing |
| * interrupt routing information. |
| * To avoid this, we enable (unused) port 6 and swap it with port 1 |
| * in the case that ethernet port 1 is disabled. Since no devices |
| * are connected to that port, we don't have to worry about interrupt |
| * routing. |
| */ |
| int port_shuffle = 0; |
| |
| /* Disable unused devices */ |
| reg32 = FD_ACMOD|FD_ACAUD|FD_PATA; |
| reg32 |= FD_PCIE6|FD_PCIE5|FD_PCIE4; |
| |
| if (read_option(ethernet1, 0) != 0) { |
| printk(BIOS_DEBUG, "Disabling ethernet adapter 1.\n"); |
| reg32 |= FD_PCIE1; |
| } |
| if (read_option(ethernet2, 0) != 0) { |
| printk(BIOS_DEBUG, "Disabling ethernet adapter 2.\n"); |
| reg32 |= FD_PCIE2; |
| } else { |
| if (reg32 & FD_PCIE1) |
| port_shuffle = 1; |
| } |
| if (read_option(ethernet3, 0) != 0) { |
| printk(BIOS_DEBUG, "Disabling ethernet adapter 3.\n"); |
| reg32 |= FD_PCIE3; |
| } else { |
| if (reg32 & FD_PCIE1) |
| port_shuffle = 1; |
| } |
| |
| if (port_shuffle) { |
| /* Enable PCIE6 again */ |
| reg32 &= ~FD_PCIE6; |
| /* Swap PCIE6 and PCIE1 */ |
| RCBA32(RPFN) = 0x00043215; |
| } |
| |
| reg32 |= 1; |
| |
| RCBA32(0x3418) = reg32; |
| |
| /* Enable PCIe Root Port Clock Gate */ |
| // RCBA32(0x341c) = 0x00000001; |
| } |
| |
| static void early_ich7_init(void) |
| { |
| uint8_t reg8; |
| uint32_t reg32; |
| |
| // program secondary mlt XXX byte? |
| pci_write_config8(PCI_DEV(0, 0x1e, 0), 0x1b, 0x20); |
| |
| // reset rtc power status |
| reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xa4); |
| reg8 &= ~(1 << 2); |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xa4, reg8); |
| |
| // usb transient disconnect |
| reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xad); |
| reg8 |= (3 << 0); |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xad, reg8); |
| |
| reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xfc); |
| reg32 |= (1 << 29) | (1 << 17); |
| pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xfc, reg32); |
| |
| reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xdc); |
| reg32 |= (1 << 31) | (1 << 27); |
| pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xdc, reg32); |
| |
| RCBA32(0x0088) = 0x0011d000; |
| RCBA16(0x01fc) = 0x060f; |
| RCBA32(0x01f4) = 0x86000040; |
| RCBA32(0x0214) = 0x10030549; |
| RCBA32(0x0218) = 0x00020504; |
| RCBA8(0x0220) = 0xc5; |
| reg32 = RCBA32(0x3410); |
| reg32 |= (1 << 6); |
| RCBA32(0x3410) = reg32; |
| reg32 = RCBA32(0x3430); |
| reg32 &= ~(3 << 0); |
| reg32 |= (1 << 0); |
| RCBA32(0x3430) = reg32; |
| RCBA32(0x3418) |= (1 << 0); |
| RCBA16(0x0200) = 0x2008; |
| RCBA8(0x2027) = 0x0d; |
| RCBA16(0x3e08) |= (1 << 7); |
| RCBA16(0x3e48) |= (1 << 7); |
| RCBA32(0x3e0e) |= (1 << 7); |
| RCBA32(0x3e4e) |= (1 << 7); |
| |
| // next step only on ich7m b0 and later: |
| reg32 = RCBA32(0x2034); |
| reg32 &= ~(0x0f << 16); |
| reg32 |= (5 << 16); |
| RCBA32(0x2034) = reg32; |
| } |
| |
| void main(unsigned long bist) |
| { |
| u32 reg32; |
| int boot_mode = 0; |
| int cbmem_was_initted; |
| |
| if (bist == 0) |
| enable_lapic(); |
| |
| /* Force PCIRST# */ |
| pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, SBR); |
| udelay(200 * 1000); |
| pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, 0); |
| |
| ich7_enable_lpc(); |
| early_superio_config_w83627thg(); |
| |
| /* Set up the console */ |
| console_init(); |
| |
| /* Halt if there was a built in self test failure */ |
| report_bist_failure(bist); |
| |
| if (MCHBAR16(SSKPD) == 0xCAFE) { |
| printk(BIOS_DEBUG, "soft reset detected, rebooting properly\n"); |
| outb(0x6, 0xcf9); |
| while (1) asm("hlt"); |
| } |
| |
| /* Perform some early chipset initialization required |
| * before RAM initialization can work |
| */ |
| i945_early_initialization(); |
| |
| /* Read PM1_CNT */ |
| reg32 = inl(DEFAULT_PMBASE + 0x04); |
| printk(BIOS_DEBUG, "PM1_CNT: %08x\n", reg32); |
| if (((reg32 >> 10) & 7) == 5) { |
| #if CONFIG_HAVE_ACPI_RESUME |
| printk(BIOS_DEBUG, "Resume from S3 detected.\n"); |
| boot_mode = 2; |
| /* Clear SLP_TYPE. This will break stage2 but |
| * we care for that when we get there. |
| */ |
| outl(reg32 & ~(7 << 10), DEFAULT_PMBASE + 0x04); |
| |
| #else |
| printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n"); |
| #endif |
| } |
| |
| /* Enable SPD ROMs and DDR-II DRAM */ |
| enable_smbus(); |
| |
| #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8 |
| dump_spd_registers(); |
| #endif |
| |
| sdram_initialize(boot_mode, NULL); |
| |
| /* Perform some initialization that must run before stage2 */ |
| early_ich7_init(); |
| |
| /* This should probably go away. Until now it is required |
| * and mainboard specific |
| */ |
| rcba_config(); |
| |
| /* Chipset Errata! */ |
| fixup_i945_errata(); |
| |
| /* Initialize the internal PCIe links before we go into stage2 */ |
| i945_late_initialization(); |
| |
| #if !CONFIG_HAVE_ACPI_RESUME |
| #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8 |
| #if CONFIG_DEBUG_RAM_SETUP |
| sdram_dump_mchbar_registers(); |
| #endif |
| |
| { |
| /* This will not work if TSEG is in place! */ |
| u32 tom = pci_read_config32(PCI_DEV(0,2,0), 0x5c); |
| |
| printk(BIOS_DEBUG, "TOM: 0x%08x\n", tom); |
| ram_check(0x00000000, 0x000a0000); |
| //ram_check(0x00100000, tom); |
| } |
| #endif |
| #endif |
| |
| quick_ram_check(); |
| |
| MCHBAR16(SSKPD) = 0xCAFE; |
| |
| cbmem_was_initted = !cbmem_recovery(boot_mode==2); |
| |
| #if CONFIG_HAVE_ACPI_RESUME |
| /* If there is no high memory area, we didn't boot before, so |
| * this is not a resume. In that case we just create the cbmem toc. |
| */ |
| if ((boot_mode == 2) && cbmem_was_initted) { |
| void *resume_backup_memory = cbmem_find(CBMEM_ID_RESUME); |
| |
| /* copy 1MB - 64K to high tables ram_base to prevent memory corruption |
| * through stage 2. We could keep stuff like stack and heap in high tables |
| * memory completely, but that's a wonderful clean up task for another |
| * day. |
| */ |
| if (resume_backup_memory) |
| memcpy(resume_backup_memory, (void *)CONFIG_RAMBASE, HIGH_MEMORY_SAVE); |
| |
| /* Magic for S3 resume */ |
| pci_write_config32(PCI_DEV(0, 0x00, 0), SKPAD, SKPAD_ACPI_S3_MAGIC); |
| } |
| #endif |
| } |