| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| /* |
| * The mainboard must define a PNOT method to handle power |
| * state notifications and Notify CPU device objects to |
| * re-evaluate their _PPC and _CST tables. |
| */ |
| |
| Device (EC0) |
| { |
| Name (_HID, EISAID ("PNP0C09")) |
| Name (_UID, 1) |
| Name (_GPE, EC_SCI_GPI + 16) // GPE for Runtime SCI |
| |
| // EC RAM fields |
| OperationRegion(ERAM, EmbeddedControl, 0, 0xFF) |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| // [Configuration Space 0] |
| , 1, // Reserved bit[0] |
| ENGA, 1, // Enable Global attention |
| ENHY, 1, // Enable Hotkey function |
| HFNE, 1, // Enable Sticky Fn Key |
| DSEM, 1, // Disable embedded NumPad Emulation |
| EN3R, 1, // Enable 3rd Host interface and TWR registers |
| , 1, // Reserved bit[6] |
| ENTM, 1, // Enable Thermal monitoring |
| |
| Offset(0x01), // [Configuration Space 1] |
| ENBK, 1, // Enable Panel backlight on/ off synchronized with LID state |
| , 3, // Reserved bits[1:3] |
| WPSW, 1, // Warning if the power switch is depressed |
| , 2, // Reserved bits[5:6] |
| NTKY, 1, // do not ignore any key while Fn key is held down |
| |
| Offset(0x02), // [Configuration Space 2] |
| , 5, // Reserved bits[0:4] |
| SNLC, 1, // Smart NumLock Enable. 1:Enable 0:Disable |
| , 1, // Reserved bit[6] |
| TNKB, 1, // ThinkVantage button function bit |
| // 0: Scan code (Enter key) |
| // 1: SMI/SCI attention |
| |
| Offset(0x03), // [Configuration Space 3] |
| DSHP, 1, // Disable to synchronize headphone state with the speaker mute |
| IGPK, 1, // Ignore phantom keys |
| , 2, // Reserved bits[2:3] |
| CBAT, 1, // Change discharge/charge preference to discharge primary battery first and charge secondary battery first if possible |
| ADO0, 1, // Audio button behavior mode 0 |
| ADO1, 1, // Audio button behavior mode 1 |
| , 1, // Enable to use PMH fan functions to get the fan speed |
| |
| Offset(0x04), // [Sound Mask 0] |
| , 1, // reserved |
| CLBA, 1, // critical low battery alarm |
| LWBA, 1, // low battery alarm (YELLOW -> RED) |
| SUBE, 1, // suspend beep |
| PUBE, 1, // vm_suspend beep |
| RSBE, 1, // resume beep |
| DCBE, 1, // DC in/out beep |
| PFBE, 1, // power off beep |
| |
| Offset(0x05), // [Sound Mask 1] |
| HSPA, 1, // power off alarm |
| NHDD, 1, // no HDD alarm |
| DEAD, 1, // dead |
| B440, 1, // 440 hz beep |
| B315, 1, // 315 hz beep |
| T315, 1, // two 315 hz beep |
| R315, 1, // three 315 hz beep |
| BYAM, 1, // inhibit swap |
| |
| Offset(0x06), // [Sound ID (Write only)] |
| HSUN, 8, // Sound ID (Write Only) |
| |
| Offset(0x07), // [Sound Repeat Interval (unit time 125ms)] |
| HSRP, 8, // Sound Repeat Interval (Unit time : 125ms ) |
| |
| Offset(0x08), // [Sound Mask 2] |
| Offset(0x09), // [KBD ID] |
| Offset(0x0A), // [KMC command control] |
| // Offset 0xOB : reserved |
| |
| Offset(0x0C), // [LED On/Off/ Blinking Control (Write only)] |
| HLCL, 4, // 0: power LED |
| // 1: battery status 0 |
| // 2: battery status 1 |
| // 3: additional Bay LED (Venice) / reserved (Toronto-4) / Slicer LED (Tokyo) |
| // 4-6: reserved |
| // 7: suspend LED |
| // 8: dock LED 1 |
| // 9: dock LED 2 |
| // 10-13: reserved |
| // 14: microphone mute |
| // 15: reserved |
| , 1, // Reserved bit[4] |
| , 1, // Blink gradually |
| BLIK, 1, // Blinking |
| TONF, 1, // Turn on/off |
| |
| Offset(0x0D), // [Peripheral control 3] |
| UONE, 1, // Bit0 - Enable to supply power through USB in S3, S4 and S5 state. |
| , 1, // Reserved bit[1] |
| , 1, // set USB_AO_SEL0 signal in S3, S4, and S5 state |
| , 1, // set USB_AO_SEL1 signal in S3, S4, and S5 state |
| , 4, // Reserved bits[4:7] |
| |
| Offset(0x0E), // [Peripheral Status 4] |
| HFNS, 2, // Bit[1, 0] : Fn Key Status |
| // [0, 0] ... Unlock |
| // [0, 1] ... Sticky |
| // [1, 0] ... Lock |
| // [1, 1] ... Reserved |
| GSER, 1, // G-Sensor Diag Error. 1:Error / 0: No error |
| PSCS, 1, // Inhibit charging |
| , 1, // External power saving mode |
| GSUD, 1, // G-Sensor under Diag. 1: Diag is running/0: Diag comp(not running) |
| GSID, 2, // Bit[7,6] G-Sensor type ID |
| // [0,0] ... None |
| // [0,1] ... STMicro |
| // [1,0] ... Memsic |
| // [1,1] ... ADI |
| |
| Offset(0x0F), // [Peripheral status 5 (read only)] |
| , 4, // Reserved bits[0:3] |
| HDSU, 1, // HDD was detached in suspend (this bit is cleared when the system enters into suspend) |
| BYSU, 1, // Bay HDD was detached in suspend (this bit is cleared when the system enters into suspend) |
| , 1, // NumLock state of the embedded keyboard |
| TMOD, 1, // Tablet mode switch |
| |
| Offset(0x10), // [Attention Mask (00-127)] |
| HAM0, 8, // 10 : Attention Mask (00-07) |
| HAM1, 8, // 11 : Attention Mask (08-0F) |
| HAM2, 8, // 12 : Attention Mask (10-17) |
| HAM3, 8, // 13 : Attention Mask (18-1F) |
| HAM4, 8, // 14 : Attention Mask (20-27) |
| HAM5, 8, // 15 : Attention Mask (28-2F) |
| HAM6, 8, // 16 : Attention Mask (30-37) |
| HAM7, 8, // 17 : Attention Mask (38-3F) |
| HAM8, 8, // 18 : Attention Mask (40-47) |
| HAM9, 8, // 19 : Attention Mask (48-4F) |
| HAMA, 8, // 1A : Attention Mask (50-57) |
| HAMB, 8, // 1B : Attention Mask (58-5F) |
| HAMC, 8, // 1C : Attention Mask (60-67) |
| HAMD, 8, // 1D : Attention Mask (68-6F) |
| HAME, 8, // 1E : Attention Mask (70-77) |
| HAMF, 8, // 1F : Attention Mask (78-7F) |
| |
| // Offset 0x20 : reserved |
| Offset(0x21), // [Inhibit Charge timer byte High (00h)] (timer is kicked when high byte is written) |
| |
| Offset(0x23), // [Misc. control] |
| // 01h Reset charge inhibit |
| // 02h Inhibit to charge |
| // 03h Reset external power saving mode |
| // 04h Set to external power saving mode |
| // 09h Emulate pressing an eject button of optical device in the bay |
| // 0Ah Reset thermal state to control the fan |
| // 10h Start gravity sensor diagnostic program |
| |
| // Offset 24-26 : reserved |
| Offset(0x27), // [Passward Scan Code] |
| // Offset 28-29 : reserved |
| |
| Offset(0x2A), // [Attention Request] |
| HATR, 8, // 2A : Attention request |
| |
| Offset(0x2B), // [Trip point of battery capacity] |
| HT0H, 8, // 2B : MSB of Trip Point Capacity for Battery 0 |
| HT0L, 8, // 2C : LSB of Trip Point Capacity for Battery 0 |
| HT1H, 8, // 2D : MSB of Trip Point Capacity for Battery 1 |
| HT1L, 8, // 2E : LSB of Trip Point Capacity for Battery 1 |
| |
| Offset(0x2F), // [Fan Speed Control] |
| HFSP, 8, // bit 2-0: speed (0: stop, 7:highest speed) |
| // bit 5-3: reserved (should be 0) |
| // bit 6: max. speed |
| // bit 7: Automatic mode (fan speed controlled by thermal level) |
| |
| Offset(0x30), // [Audio mute control] |
| , 7, // Reserved bits[0:6] |
| SMUT, 1, // Mute |
| |
| Offset(0x31), // [Peripheral Control 2] |
| FANS, 2, // bit 0,1 Fan selector |
| // 00: Fan 1, 01: Fan 2 |
| HUWB, 1, // UWB on |
| ENS4, 1, // Reserved bit[3] |
| DSEX, 1, // Disable Express Card |
| AYID, 1, // Always-on Card identified |
| , 1, // Select USB to Always On card |
| , 1, // Assert the express card slot power control standby signal |
| |
| Offset(0x32), // [EC Event Mask 0] |
| HWPM, 1, // PME : Not used. PME# is connected to GPE directly. |
| HWLB, 1, // Critical Low Bat |
| HWLO, 1, // Lid Open |
| , 1, // Eject button |
| HWFN, 1, // FN key |
| , 1, // Portfino wake up |
| HWRI, 1, // Ring Indicator (UART) |
| HWBU, 1, // Bay Unlock |
| |
| Offset(0x33), // [EC Event Mask 1] |
| |
| Offset(0x34), // [Peripheral status 2 (read only)] |
| , 1, // Reserved bit[0] |
| , 1, // Beep is being sounded now |
| , 1, // SMBus is busy |
| , 1, // Reserved bit[3] |
| , 1, // Fan exists |
| , 1, // Gravity sensors exist |
| , 1, // Reserved bit[6] |
| HPLO, 1, // Power consumption warning |
| |
| Offset(0x35), // [Peripheral status 3 (Read only)] |
| , 1, // Input devices (keyboard and mouse) are locked by password |
| , 1, // Input devices are frozen (input from devices are inhibited) |
| , 1, // Fan power on Reset is done |
| , 1, // Attention is disabled temporarily |
| , 1, // Fan error |
| , 2, // Reserved bit[5:6] |
| , 1, // Thermal sensor error |
| |
| Offset(0x36), // [Copy register of EC Event Status (0x32)] |
| Offset(0x37), // [Copy register of EC Event Status (0x33)] |
| |
| Offset(0x38), // [Battery 0 status (read only)] |
| HB0S, 7, // bit 3-0 level |
| // F: Unknown |
| // 2-n: battery level |
| // 1: low level |
| // 0: (critical low battery, suspend/ hibernate) |
| // bit 4 error |
| // bit 5 charge |
| // bit 6 discharge |
| MBTS, 1, // bit 7 battery attached |
| |
| Offset(0x39), // [Battery 1 status (read only)] |
| // bit definition is the same as offset(0x38) |
| |
| Offset(0x3A), // [Peripheral control 0] |
| MUTE, 1, // Mute |
| I2CS, 1, // I2C select ( 0:Dock EEPROM etc, 1:Thermal sensor etc )(Tokyo-2) |
| PWRF, 1, // Power off |
| WANO, 1, // H/W Override bit |
| // (enable to control wireless devices even if the global WAN disable switch is ON) |
| DCBD, 1, // Bluetooth On |
| DCWL, 1, // Wireless Lan On |
| DCWW, 1, // Wireless Wan On |
| , 1, // 2nd Battery Inhibit (Tokyo) |
| |
| Offset(0x3B), // [Peripheral control 1] |
| SPKM, 1, // Speaker Mute |
| KBLH, 1, // Keyboard Light |
| , 1, // Reserved bit[2] |
| BTDH, 1, // Bluetooth detach |
| USBN, 1, // USB On |
| , 1, // Inhibit communication with battery 0 |
| , 1, // Inhibit communication with battery 1 |
| S3FG, 1, // Reserved bit[7] |
| |
| Offset(0x3C), // [Resume reason (Read only)] |
| Offset(0x3D), // [Password Control byte] |
| Offset(0x3E), // [Password data (8 byte)~ offset:45h] |
| |
| Offset(0x46), // [sense status 0] |
| FNKY, 1, // Fn key |
| , 1, // Reserved bit[1] |
| HPLD, 1, // LID open |
| PROF, 1, // Power off |
| ACPW, 1, // External power (AC status) |
| , 2, // Reserved bits[5:6] |
| CALR, 1, // LP mode (power consumption alert) |
| |
| Offset(0x47), // [sense status 1] |
| HPBU, 1, // Bay Unlock |
| DKEV, 1, // Dock event |
| BYNO, 1, // Bay is not Attached |
| HDIB, 1, // HDD in the bay |
| , 4, // Reserved bits[4:7] |
| |
| Offset(0x48), // [sense status 2] |
| HPHI, 1, // Head Phone In |
| GSTS, 1, // Global Wan Enable Switch |
| , 2, // Reserved bits[2:3] |
| EXGC, 1, // External Graphic Chip |
| DOKI, 1, // Dock attached |
| HDDT, 1, // HDD detect |
| , 1, // Reserved bit[7] |
| |
| Offset(0x49), // [sense status 3] |
| // Offset 0x4A : reserved |
| |
| Offset(0x4C), // [MSB of Event Timer] |
| ETHB, 8, // bit[14:0]=timer counter, bit[15], 0:ms, 1:sec |
| |
| Offset(0x4D), // [LSB of Event Timer] |
| ETLB, 8, // |
| |
| Offset(0x4E), // [EC Event Status 0] |
| Offset(0x4F), // [EC Event Status 1] |
| |
| Offset(0x50), // [SMB_PRTCL (protocol register)] |
| SMPR, 8, // 00: Controller Not In use |
| // 01: reserved |
| // 02: Write Quick command |
| // 03: Read Quick command |
| // 04: Send Quick command |
| // 05: Receive Byte |
| // 06: Write Byte |
| // 07: Read Byte |
| // 08: Write Word |
| // 09: Read Word |
| // 0A: Write block |
| |
| Offset(0x51), // [SMB_STS (status register)] |
| SMST, 8, // bits[0:4] Status |
| // bit[5] Reserved |
| // bit[6] Alarm Received |
| // bit[7] Done |
| |
| Offset(0x52), // [SMB_ADDR (address register)] |
| SMAD, 8, // |
| |
| Offset(0x53), // [SMB_CMD (Command register)] |
| SMCM, 8, // |
| |
| Offset(0x54), // [SMB_DATA (Data Register (32 bytes))~ offset:73h] |
| SMD0, 100, // |
| |
| Offset(0x74), // [SMB_BCNT (Block count register)] |
| BCNT, 8, // |
| |
| Offset(0x75), // [SMB_ALRM_ADDR (Alarm address register)] |
| SMAA, 8, // |
| |
| Offset(0x76), // [SMB_ALRM_DATA (Alarm data register (2 bytes))] |
| BATD, 16, // |
| |
| Offset(0x78), // [Temperature of thermal sensor 0 (centigrade)] |
| TMP0, 8, // 78 : Temperature of thermal sensor 0 |
| TMP1, 8, // 79 : Temperature of thermal sensor 1 |
| TMP2, 8, // 7A : Temperature of thermal sensor 2 |
| TMP3, 8, // 7B : Temperature of thermal sensor 3 |
| TMP4, 8, // 7C : Temperature of thermal sensor 4 |
| TMP5, 8, // 7D : Temperature of thermal sensor 5 |
| TMP6, 8, // 7E : Temperature of thermal sensor 6 |
| TMP7, 8, // 7F : Temperature of thermal sensor 7 |
| |
| // Offset 79-7F : reserved |
| Offset(0x80), // [Attention control byte] |
| |
| Offset(0x81), // [Battery information ID for 0xA0-0xAF] |
| HIID, 8, // (this byte is depend on the interface, 62&66 and 1600&1604) |
| |
| Offset(0x82), // [Fn Dual function - make time out time (100ms unit)] |
| |
| Offset(0x83), // [Fn Dual function ID] |
| HFNI, 8, // 0: none |
| // 1-3: Reserved |
| // 4: ACPI Power |
| // 5: ACPI Sleep |
| // 6: ACPI Wake |
| // 7: Left Ctrl key |
| |
| Offset(0x84), // [Fan Speed] |
| , 16, // |
| // (I/F Offset 3Bh bit5 => 0:Main Fan , 1:Second Fan) |
| |
| Offset(0x86), // [password 0 - 7 status] |
| Offset(0x87), // [password 8 - 15 status] |
| Offset(0x88), // [Thermal Status of Level 0 (low)] |
| Offset(0x89), // [Thermal Status of Level 1 (middle)] |
| Offset(0x8A), // [Thermal Status of Level 2 (middle high)] |
| Offset(0x8B), // [Thermal Status of Level 3 (high)] |
| // Offset 0x8C : reserved |
| |
| Offset(0x8D), // [Interval of polling Always-on cards in half minute] |
| HDAA, 3, // Warning Delay Period |
| HDAB, 3, // Stolen Delay Period |
| HDAC, 2, // Sensitivity |
| |
| Offset(0x8E), // [Key-number assigned to the ThinkVantage button] |
| Offset(0x8F), // [EC Internal Use for Fan Duty Table Creation] |
| Offset(0x90), // [EC internal use] |
| Offset(0xA0), // [Battery Information Area]~ offset:0AFh |
| Offset(0xB0), // [Battery 0 charge start capacity] |
| Offset(0xB1), // [Battery 0 charge stop capacity] |
| Offset(0xB2), // [Battery 1 charge start capacity] |
| Offset(0xB3), // [Battery 1 charge stop capacity] |
| |
| Offset(0xB4), // [Battery 0 control] |
| // 01h Stop refreshing the battery |
| // 02h Refresh the battery |
| // 07h Set long life span mode |
| // 08h Set long run time mode |
| |
| Offset(0xB5), // [Battery 1 control] |
| // Offset B6-C7 : reserved |
| |
| Offset(0xC8), // [Adaptive Thermal Management (ATM)] |
| ATMX, 8, // bit 7-4 - Thermal Table & bit 3-0 - Fan Speed Table |
| |
| Offset(0xC9), // [Wattage of AC/DC] |
| AC65, 8, // |
| |
| Offset(0xCA), // Reserved - but should be 0 |
| |
| Offset(0xCB), // [ATM configuration] |
| BFUD, 1, // bit 0 - Battery FUD Flag |
| , 7, // bit 1~7 - Reserved |
| |
| Offset(0xCC), // |
| PWMH, 8, // CC : AC Power Consumption (MSB) |
| PWML, 8, // CD : AC Power Consumption (LSB) - unit: 100mW |
| |
| Offset(0xCE), // [Configuration Space 4] |
| , 2, // Windows key mode |
| , 2, // Application key mode |
| , 1, // Swap the Fn key and the left Ctrl key |
| , 3, // Reserved bits[5:7] |
| |
| Offset(0xCF), // [Configuration Space 5] |
| HSID, 8, // Hand shaking byte of system information ID |
| |
| Offset(0xD0), // [EC Type] |
| // D1-DF : reserved |
| |
| Offset(0xE0), // @@ Mapping to old EC RAM for battery information |
| ECRC, 16, // BAT1 Sys command [0] RC |
| ECAC, 16, // BAT1 Sys command [0] AV_I |
| ECVO, 16, // BAT1 Sys command [0] Voltage |
| |
| // E1-E7 : reserved |
| Offset(0xE8), // [Version 0] |
| Offset(0xE9), // [Version 1] |
| Offset(0xEA), // [Machine ID] |
| Offset(0xEB), // [Function Specification Minor Version] |
| Offset(0xEC), // [EC capability 0] |
| Offset(0xED), // [EC capability 1] |
| |
| Offset(0xEE), // [Highest battery level] |
| MBTH, 4, // bit 3-0: battery 0 highest level |
| SBTH, 4, // bit 7-4: battery 1 highest level |
| // note: if highest level is 0 or 0xF, it means not defined |
| // (in this case, use default highest level, it is 6) |
| |
| Offset(0xEF), // [EC Function Specification Major Version] |
| Offset(0xF0), // [Build ID]~ offset:0F7h |
| |
| Offset(0xF8), // [Build Date (F8: MSB, F9:LSB)] |
| , 4, // bit 3-0: day(1-31) |
| , 4, // bit 7-4: month(1-12) |
| , 8, // bit 15-8: year(2000 base) |
| |
| Offset(0xFA), // [Build Time (in 2seconds)] |
| // ex: when index FAh=5Ah and index FBh=ADh, Build Time is 5AADh .. 12:53:46 |
| |
| Offset(0xFC), // [reserved]~ offset:0FFh |
| } // End of ERAM |
| |
| // |
| // Battery Information ID : 00/10 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| SBRC, 16, // Remaining Capacity |
| SBFC, 16, // Fully Charged Capacity |
| SBAE, 16, // Average Time To Empty |
| SBRS, 16, // Relative State Of Charge |
| SBAC, 16, // Average Current |
| SBVO, 16, // Voltage |
| SBAF, 16, // Average Time To Full |
| SBBS, 16, // Battery State |
| } |
| |
| // |
| // Battery Information ID : 01/11 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| // Battery Mode(w) |
| , 15, |
| SBCM, 1, // bit 15 - CAPACITY_MODE |
| // 0: Report in mA/mAh ; 1: Enabled |
| SBMD, 16, // Manufacture Data |
| SBCC, 16, // Cycle Count |
| } |
| |
| // |
| // Battery Information ID : 02/12 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| SBDC, 16, // Design Capacity |
| SBDV, 16, // Design Voltage |
| SBOM, 16, // Optional Mfg Function 1 |
| SBSI, 16, // Specification Info |
| SBDT, 16, // Manufacture Date |
| SBSN, 16, // Serial Number |
| } |
| |
| // |
| // Battery Information ID : 04/14 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| SBCH, 32, // Device Checmistory (string) |
| } |
| |
| // |
| // Battery Information ID : 05/15 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| SBMN, 128, // Manufacture Name (s) |
| } |
| |
| // |
| // Battery Information ID : 06/16 |
| // |
| Field (ERAM, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0xA0), |
| SBDN, 128, // Device Name (s) |
| } |
| |
| Method (_CRS, 0, NotSerialized) |
| { |
| Name (ECMD, ResourceTemplate() |
| { |
| IO (Decode16, 0x62, 0x62, 0, 1) |
| IO (Decode16, 0x66, 0x66, 0, 1) |
| }) |
| Return (ECMD) |
| } |
| |
| Method (_REG, 2, NotSerialized) |
| { |
| // Initialize AC power state |
| Store (ACPW, \PWRS) |
| |
| // Initialize LID switch state |
| Store (NOT(HPLD), \LIDS) |
| |
| // Enable OS control of fan speed |
| // TODO Store (One, FCOS) |
| |
| // Force a read of CPU temperature |
| // TODO Which temperature corresponds to the CPU? |
| Store (TMP0, Local0) |
| /* So that we don't get a warning that Local0 is unused. */ |
| Local0++ |
| } |
| |
| /* Attention Codes |
| * 00h No Event |
| * 01h-0Fh Reserved for ACPI Events |
| * 10h-1Fh Hotkey Events |
| * 22h Critical Low Battery |
| * 23h Battery Empty |
| * 24h Trip Point Capacity Event for Battery 0 |
| * 26h AC Adapter Attached |
| * 27h AC Adapter Detached |
| * 28h Power Off Switch Pressed |
| * 29h Power Off Switch Released |
| * 2Ah LID Open |
| * 2Bh LID Close |
| * 3Eh PME Event |
| * 40h Thermal Event |
| * 41h Global Wireless Enable Switch |
| * 43h Mute State Change |
| * 4Ah Battery 0 Attach/Detach |
| * 4Bh Battery 0 State Change |
| * 66h Mute Button |
| */ |
| |
| // Battery at critical low state |
| Method (_Q22) |
| { |
| If (MBTS) |
| { |
| Notify (BATX, 0x80) |
| } |
| } |
| |
| // AC Power Connected |
| Method (_Q26, 0, NotSerialized) |
| { |
| Store (One, \PWRS) |
| Notify (AC, 0x80) |
| Notify (BATX, 0x80) |
| \PNOT () |
| } |
| |
| // AC Power Removed |
| Method (_Q27, 0, NotSerialized) |
| { |
| Store (Zero, \PWRS) |
| Notify (AC, 0x80) |
| \PNOT () |
| } |
| |
| // LID Open |
| Method (_Q2A) |
| { |
| Store (One, \LIDS) |
| Notify (\_SB.LID0, 0x80) |
| } |
| |
| // LID Close (Suspend Trigger) |
| Method (_Q2B) |
| { |
| Store (Zero, \LIDS) |
| Notify (\_SB.LID0, 0x80) |
| } |
| |
| // Battery Attach/Detach Event |
| Method (_Q4A) |
| { |
| Notify (BATX, 0x80) |
| Notify (BATX, 0x81) |
| \PNOT () |
| } |
| |
| // Battery State Change Event |
| Method (_Q4B) |
| { |
| Notify (BATX, 0x80) |
| } |
| |
| // Global Wireless Disable/Enable Event |
| Method (_Q41, 0, NotSerialized) |
| { |
| IF (DCWL) //if Wlan exist |
| { |
| //TODO Store (WLAT, LANE) |
| } |
| } |
| |
| #include "ac.asl" |
| #include "battery.asl" |
| // TODO #include "fan.asl" |
| } |