| /* |
| * This file is part of the LinuxBIOS project. |
| * |
| * Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #include <arch/romcc_io.h> |
| #include "it8705f.h" |
| |
| /* The base address is 0x2e or 0x4e, depending on config bytes. */ |
| #define SIO_BASE 0x2e |
| #define SIO_INDEX SIO_BASE |
| #define SIO_DATA SIO_BASE+1 |
| |
| /* Global configuration registers. */ |
| #define IT8705F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */ |
| #define IT8705F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */ |
| #define IT8705F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */ |
| |
| /* WTF? 0x23 and 0x24 are swapped here (when compared to other IT87xx). */ |
| #define IT8705F_CONFIG_REG_CLOCKSEL 0x24 /* Clock Selection, Flash I/F. */ |
| #define IT8705F_CONFIG_REG_SWSUSP 0x23 /* Software Suspend. */ |
| |
| #define IT8705F_CONFIGURATION_PORT 0x2e /* Write-only. */ |
| |
| /* The content of IT8705F_CONFIG_REG_LDN (index 0x07) must be set to the |
| LDN the register belongs to, before you can access the register. */ |
| static void it8705f_sio_write(uint8_t ldn, uint8_t index, uint8_t value) |
| { |
| outb(IT8705F_CONFIG_REG_LDN, SIO_BASE); |
| outb(ldn, SIO_DATA); |
| outb(index, SIO_BASE); |
| outb(value, SIO_DATA); |
| } |
| |
| /* Enable the peripheral devices on the IT8705F Super I/O chip. */ |
| static void it8705f_enable_serial(device_t dev, unsigned iobase) |
| { |
| /* (1) Enter the configuration state (MB PnP mode). */ |
| |
| /* Perform MB PnP setup to put the SIO chip at 0x2e. */ |
| /* Base address 0x2e: 0x87 0x01 0x55 0x55. */ |
| /* Base address 0x4e: 0x87 0x01 0x55 0xaa. */ |
| outb(0x87, IT8705F_CONFIGURATION_PORT); |
| outb(0x01, IT8705F_CONFIGURATION_PORT); |
| outb(0x55, IT8705F_CONFIGURATION_PORT); |
| outb(0x55, IT8705F_CONFIGURATION_PORT); |
| |
| /* (2) Modify the data of configuration registers. */ |
| |
| /* Select the chip to configure (if there's more than one). |
| Set bit 7 to select JP3=1, clear bit 7 to select JP3=0. |
| If this register is not written, both chips are configured. */ |
| /* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CONFIGSEL, 0x00); */ |
| |
| /* Enable all devices. */ |
| it8705f_sio_write(IT8705F_FDC, 0x30, 0x1); /* Floppy */ |
| it8705f_sio_write(IT8705F_SP1, 0x30, 0x1); /* Serial port 1 */ |
| it8705f_sio_write(IT8705F_SP2, 0x30, 0x1); /* Serial port 2 */ |
| it8705f_sio_write(IT8705F_PP, 0x30, 0x1); /* Parallel port */ |
| it8705f_sio_write(IT8705F_EC, 0x30, 0x1); /* Environment controller */ |
| it8705f_sio_write(IT8705F_GAME, 0x30, 0x1); /* GAME port */ |
| it8705f_sio_write(IT8705F_IR, 0x30, 0x1); /* Consumer IR */ |
| it8705f_sio_write(IT8705F_MIDI, 0x30, 0x1); /* MIDI port */ |
| |
| /* Select 24MHz/48MHz CLKIN (set/clear bit 0). TODO: Needed? */ |
| /* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CLOCKSEL, 0x01); */ |
| |
| /* Clear software suspend mode (clear bit 0). TODO: Needed? */ |
| /* it8705f_sio_write(0x00, IT8705F_CONFIG_REG_SWSUSP, 0x00); */ |
| |
| /* (3) Exit the configuration state (MB PnP mode). */ |
| it8705f_sio_write(0x00, IT8705F_CONFIG_REG_CC, 0x02); |
| } |
| |