| fw_config |
| field KB_BL 0 0 |
| option KB_BL_ABSENT 0 |
| option KB_BL_PRESENT 1 |
| end |
| field AUDIO 1 3 |
| option AUDIO_UNKNOWN 0 |
| option ALC1019_ALC5682I_VD_I2S 1 |
| option ALC1019_ALC5682I_VS_I2S 2 |
| end |
| field UFC 4 4 |
| option UFC_USB 0 |
| option UFC_MIPI 1 |
| end |
| field STORAGE 30 31 |
| option STORAGE_UNKNOWN 0 |
| option STORAGE_NVME 1 |
| option STORAGE_UFS 2 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C3 | TouchScreen | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 650, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 600, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 650, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 650, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| }" |
| register "sagv" = "SaGv_Enabled" |
| |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | |
| FIVR_VOLTAGE_MIN_ACTIVE | |
| FIVR_VOLTAGE_MIN_RETENTION, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | |
| FIVR_VOLTAGE_MIN_ACTIVE | |
| FIVR_VOLTAGE_MIN_RETENTION, |
| .v1p05_icc_max_ma = 500, |
| .vnn_sx_voltage_mv = 1250, |
| }" |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # USB2_C0 |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2_Port 1 |
| register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC1)" # USB2_C2 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC2)" # Type-A Port A1 |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 4 |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Camera |
| register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 6 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # DCI port |
| register "usb2_ports[8]" = "USB2_PORT_MID(OC3)" # Type-A Port A0 |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Bluetooth |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC3)" # USB3/2 Type A port A0 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # DCI port |
| register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Disable USB3 Port 2 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC2)" # USB3/2 Type A port A1 |
| |
| register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC0)" |
| register "tcss_ports[1]" = "TCSS_PORT_EMPTY" |
| register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC1)" |
| |
| device domain 0 on |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO AUDIO_UNKNOWN |
| probe AUDIO ALC1019_ALC5682I_VD_I2S |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO ALC1019_ALC5682I_VS_I2S |
| end |
| end |
| chip drivers/generic/alc1015 |
| register "hid" = ""RTL1019"" |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| device generic 1 on end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end #I2C1 |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "reset_delay_ms" = "300" |
| register "reset_off_delay_ms" = "1" |
| register "enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "enable_delay_ms" = "6" |
| register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "stop_off_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on end |
| end |
| end #I2C3 |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PIXA2342"" |
| register "generic.desc" = ""PIXA Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "hid_desc_reg_offset" = "0x1" |
| device i2c 15 on end |
| end |
| end #I2C5 |
| device ref pcie_rp5 on |
| # Enable wlan PCIe 5 using clk 2 |
| register "pch_pcie_rp[PCH_RP(5)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW1_03" |
| device pci 00.0 on end |
| end |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" |
| register "srcclk_pin" = "2" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp8 off end |
| device ref pcie_rp11 on |
| # Enable NVMe SSD PCIe 11-12 using clk 1 |
| register "pch_pcie_rp[PCH_RP(11)]" = "{ |
| .clk_src = 1, |
| .clk_req = 1, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| probe STORAGE STORAGE_UNKNOWN |
| probe STORAGE STORAGE_NVME |
| end |
| device ref ish on |
| probe STORAGE STORAGE_UFS |
| end |
| device ref ufs on |
| probe STORAGE STORAGE_UFS |
| end |
| device ref gspi1 on |
| chip drivers/spi/acpi |
| register "name" = ""CRFP"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "uid" = "1" |
| register "compat_string" = ""google,cros-ec-spi"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)" |
| register "enable_delay_ms" = "3" |
| device spi 0 on end |
| end # FPMCU |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 2))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 2))" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end |
| end |
| end |