| chip soc/intel/alderlake |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "pmc_gpe0_dw0" = "GPP_C" |
| register "pmc_gpe0_dw1" = "GPP_D" |
| register "pmc_gpe0_dw2" = "GPP_E" |
| |
| # TCSS |
| register "TcssAuxOri" = "1" |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_A5, .pad_auxn_dc = GPP_A6}" |
| |
| # Enable heci communication |
| register "HeciEnabled" = "1" |
| |
| # Enable CNVi Bluetooth |
| register "CnviBtCore" = "true" |
| |
| |
| # FSP configuration |
| register "SaGv" = "SaGv_Disabled" |
| |
| # S0ix enable |
| register "s0ix_enable" = "1" |
| |
| register "usb2_ports[0]" = "USB2_PORT_MID(OC1)" # Type-A Port A0 |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # Type-A Port A1 |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # M.2 WWAN |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC0)" # Type-A / Type-C Cl |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Camera |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC3)" # Type-A / Type-C Co |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Bluetooth |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)" # USB3/2 Type A port A0 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC2)" # USB3/2 Type A port A1 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # M.2 WWAN |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| # EC memory map range is 0x900-0x9ff |
| register "gen3_dec" = "0x00fc0901" |
| |
| # Enable PCH PCIE RP 5 using CLK 1 |
| register "pch_pcie_rp[PCH_RP(5)]" = "{ |
| .clk_src = 1, |
| .clk_req = 1, |
| .flags = PCIE_RP_CLK_REQ_DETECT, |
| }" |
| |
| # Enable NVMe PCIE 9 using clk 0 |
| register "pch_pcie_rp[PCH_RP(9)]" = "{ |
| .clk_src = 0, |
| .clk_req = 0, |
| .flags = PCIE_RP_LTR, |
| }" |
| |
| # Enable SD Card PCIE 8 using clk 3 |
| register "pch_pcie_rp[PCH_RP(8)]" = "{ |
| .clk_src = 3, |
| .clk_req = 3, |
| .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR, |
| }" |
| |
| # Enable SATA |
| register "SataEnable" = "1" |
| register "SataMode" = "0" |
| register "SataSalpSupport" = "1" |
| register "SataPortsEnable[0]" = "0" |
| register "SataPortsEnable[1]" = "1" |
| register "SataPortsDevSlp[0]" = "0" |
| register "SataPortsDevSlp[1]" = "1" |
| register "SataPortsEnableDitoConfig[1]" = "1" |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "SerialIoGSpiMode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoPci, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI2] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI3] = PchSerialIoDisabled, |
| }" |
| |
| register "SerialIoGSpiCsMode" = "{ |
| [PchSerialIoIndexGSPI0] = 1, |
| }" |
| |
| register "SerialIoGSpiCsState" = "{ |
| [PchSerialIoIndexGSPI0] = 1, |
| }" |
| |
| register "SerialIoUartMode" = "{ |
| [PchSerialIoIndexUART0] = PchSerialIoSkipInit, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoDisabled, |
| }" |
| |
| # HD Audio |
| register "PchHdaDspEnable" = "1" |
| register "PchHdaIDispLinkTmode" = "HDA_TMODE_8T" |
| register "PchHdaIDispLinkFrequency" = "HDA_LINKFREQ_96MHZ" |
| register "PchHdaIDispCodecEnable" = "1" |
| |
| # DP port |
| register "DdiPortAConfig" = "1" # eDP |
| register "DdiPortBConfig" = "0" |
| |
| # Enable Display Port Configuration |
| register "ddi_ports_config" = "{ |
| [DDI_PORT_A] = DDI_ENABLE_HPD, |
| [DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| [DDI_PORT_1] = DDI_ENABLE_HPD, |
| [DDI_PORT_2] = DDI_ENABLE_HPD, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | SAR0, WWAN, HDMI | |
| #| I2C1 | Camera | |
| #| I2C2 | Audio | |
| #| I2C3 | Touchscreen, USI | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| device domain 0 on |
| device ref igpu on end |
| device ref dtt on end |
| device ref ipu on end |
| device ref tbt_pcie_rp0 on end |
| device ref tbt_pcie_rp1 on end |
| device ref tbt_pcie_rp2 on end |
| device ref tbt_pcie_rp3 on end |
| device ref crashlog off end |
| device ref tcss_xhci on end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp" = "{ |
| [0] = {.power_gpio = ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H19),}, |
| [1] = {.power_gpio = ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H19),}}" |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on end |
| device ref xhci on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" |
| device ref usb2_port10 on end |
| end |
| end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on end |
| device ref i2c1 on end |
| device ref i2c2 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F9)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "0" |
| register "imon_slot_no" = "1" |
| register "uid" = "0" |
| register "desc" = ""Right Speaker Amp"" |
| register "name" = ""MAXR"" |
| device i2c 31 on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "2" |
| register "imon_slot_no" = "3" |
| register "uid" = "1" |
| register "desc" = ""Left Speaker Amp"" |
| register "name" = ""MAXL"" |
| device i2c 32 on end |
| end |
| end |
| device ref i2c3 on end |
| device ref heci1 on end |
| device ref sata on end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end |
| device ref pcie_rp5 on end |
| device ref pcie_rp8 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H3)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp9 on end |
| device ref uart0 on end |
| device ref gspi0 on |
| chip drivers/spi/acpi |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cr50"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_C3_IRQ)" |
| device spi 0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref p2sb on end |
| device ref pmc hidden |
| # The pmc_mux chip driver is a placeholder for the |
| # PMC.MUX device in the ACPI hierarchy. |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| register "usb2_port_number" = "6" |
| register "usb3_port_number" = "1" |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| register "usb2_port_number" = "4" |
| register "usb3_port_number" = "2" |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref hda on end |
| device ref smbus on end |
| end |
| end |