| chip soc/intel/jasperlake |
| |
| device cpu_cluster 0 on end |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "pmc_gpe0_dw0" = "GPP_B" |
| register "pmc_gpe0_dw1" = "GPP_H" |
| register "pmc_gpe0_dw2" = "GPP_E" |
| |
| # FSP configuration |
| register "SaGv" = "SaGv_Enabled" |
| register "SmbusEnable" = "1" |
| register "ScsEmmcHs400Enabled" = "1" |
| register "SdCardPowerEnableActiveHigh" = "1" |
| |
| # Display related UPDs |
| # Select eDP for port A (1 = eDP, 2 = MIPI) |
| register "DdiPortAConfig" = "1" |
| |
| # Enable HPD for DDI ports B/C |
| register "DdiPortBHpd" = "1" |
| register "DdiPortCHpd" = "1" |
| |
| # Enable DDC for DDI ports B/C |
| register "DdiPortBDdc" = "1" |
| register "DdiPortCDdc" = "1" |
| |
| register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port1 |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # USB2 Type A port1 |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port2 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC0)" # USB2 Type A port2 |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # USB2 Bluetooth |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # USB2 WWAN |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC2)" # USB2 Type A port3 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC3)" # USB2 Type A port4 |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port1 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port2 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port1 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC2)" # USB3 WWAN |
| register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC2)" # UNUSED |
| register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC_SKIP)" # UNUSED |
| |
| # Enable Pch iSCLK |
| register "pch_isclk" = "1" |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| # EC memory map range is 0x900-0x9ff |
| register "gen3_dec" = "0x00fc0901" |
| |
| # Skip the CPU repalcement check |
| register "SkipCpuReplacementCheck" = "1" |
| |
| register "PchHdaDspEnable" = "1" |
| register "PchHdaAudioLinkHdaEnable" = "0" |
| register "PchHdaAudioLinkSspEnable[0]" = "1" |
| register "PchHdaAudioLinkSspEnable[1]" = "1" |
| register "PchHdaAudioLinkDmicEnable[0]" = "1" |
| register "PchHdaAudioLinkDmicEnable[1]" = "1" |
| |
| # PCIe port 1 for M.2 E-key WLAN |
| # Enable Root Port 4(x4) for NVMe |
| register "PcieRpEnable[1]" = "1" |
| register "PcieRpEnable[4]" = "1" |
| |
| # Enable ClkReqDetect 1 for WLAN |
| # Enable ClkReqDetect 4 for NVMe |
| register "PcieRpClkReqDetect[1]" = "1" |
| register "PcieRpClkReqDetect[4]" = "1" |
| |
| register "PcieClkSrcUsage[0]" = "0x04" |
| register "PcieClkSrcUsage[1]" = "0x01" |
| register "PcieClkSrcUsage[2]" = "0xFF" |
| register "PcieClkSrcUsage[3]" = "0xFF" |
| register "PcieClkSrcUsage[4]" = "0xFF" |
| register "PcieClkSrcUsage[5]" = "0xFF" |
| |
| register "PcieClkSrcClkReq[0]" = "0x00" |
| register "PcieClkSrcClkReq[1]" = "0x01" |
| register "PcieClkSrcClkReq[2]" = "0x02" |
| register "PcieClkSrcClkReq[3]" = "0x03" |
| register "PcieClkSrcClkReq[4]" = "0x04" |
| register "PcieClkSrcClkReq[5]" = "0x05" |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "SerialIoGSpiMode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI1] = PchSerialIoPci, |
| [PchSerialIoIndexGSPI2] = PchSerialIoDisabled, |
| }" |
| |
| register "SerialIoGSpiCsMode" = "{ |
| [PchSerialIoIndexGSPI0] = 1, |
| [PchSerialIoIndexGSPI1] = 1, |
| [PchSerialIoIndexGSPI2] = 1, |
| }" |
| |
| register "SerialIoGSpiCsState" = "{ |
| [PchSerialIoIndexGSPI0] = 0, |
| [PchSerialIoIndexGSPI1] = 0, |
| [PchSerialIoIndexGSPI2] = 0, |
| }" |
| |
| register "SerialIoUartMode" = "{ |
| [PchSerialIoIndexUART0] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoSkipInit, |
| }" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # Add PL1 and PL2 values |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| # Enable S0ix |
| register "s0ix_enable" = "1" |
| |
| # GPIO for SD card detect |
| register "sdcard_cd_gpio" = "VGPIO_39" |
| |
| register "common_soc_config" = "{ |
| .gspi[1] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 176, |
| .scl_hcnt = 95, |
| .sda_hold = 36, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| # Set the minimum assertion width |
| register "PchPmSlpS3MinAssert" = "3" # 50ms |
| register "PchPmSlpS4MinAssert" = "1" # 1s |
| register "PchPmSlpSusMinAssert" = "3" # 1s |
| register "PchPmSlpAMinAssert" = "3" # 98ms |
| |
| # NOTE: Duration programmed in the below register should never be smaller than the |
| # stretch duration programmed in the following registers - |
| # - GEN_PMCON_A.SLP_S3_MIN_ASST_WDTH (PchPmSlpS3MinAssert) |
| # - GEN_PMCON_A.S4MAW (PchPmSlpS4MinAssert) |
| # - PM_CFG.SLP_A_MIN_ASST_WDTH (PchPmSlpAMinAssert) |
| # - PM_CFG.SLP_LAN_MIN_ASST_WDTH |
| register "PchPmPwrCycDur" = "1" # 1s |
| |
| # Set xHCI LFPS period sampling off time, the default is 9ms. |
| register "xhci_lfps_sampling_offtime_ms" = "9" |
| |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on end # Integrated Graphics Device |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| register "policies.passive[0]" = "DPTF_PASSIVE(CPU, CPU, 95, 1000)" |
| register "policies.critical[0]" = "DPTF_CRITICAL(CPU, 119, SHUTDOWN)" |
| |
| register "controls.power_limits.pl1" = "{ |
| .min_power = 3000, |
| .max_power = 6000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200,}" |
| register "controls.power_limits.pl2" = "{ |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000,}" |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| |
| device pci 05.0 on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "2" |
| register "cio2_lanes_used" = "{2,2}" |
| register "cio2_lane_endpoint[0]" = ""^I2C4.CAM0"" |
| register "cio2_lane_endpoint[1]" = ""^I2C5.CAM1"" |
| register "cio2_prt[0]" = "0" |
| register "cio2_prt[1]" = "2" |
| device generic 0 on end |
| end |
| end |
| device pci 12.0 off end # Thermal Subsystem |
| device pci 12.5 off end # UFS SCS |
| device pci 12.6 off end # GSPI #2 |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3/2 Type-A Left Lower"" |
| register "type" = "UPC_TYPE_A" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB C Connector 1"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 2.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB C Connector 2"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB C Connector 3"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB C Connector 4"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 2.6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3/2 Type-A Left Upper"" |
| register "type" = "UPC_TYPE_A" |
| device usb 2.7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3/2 Type-A Left Lower"" |
| register "type" = "UPC_TYPE_A" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3/2 Type-A Left Upper"" |
| register "type" = "UPC_TYPE_A" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WLAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Port Unused1"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Port Unused2"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Port Unused3"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.2 off end # PMC SRAM |
| device pci 14.3 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end # CNVi wifi |
| device pci 14.5 on end # SDCard |
| device pci 15.0 on |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "4" |
| register "imon_slot_no" = "5" |
| register "uid" = "0" |
| register "desc" = ""RIGHT SPEAKER AMP"" |
| register "name" = ""MAXR"" |
| device i2c 31 on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "6" |
| register "imon_slot_no" = "7" |
| register "uid" = "1" |
| register "desc" = ""LEFT SPEAKER AMP"" |
| register "name" = ""MAXL"" |
| device i2c 32 on end |
| end |
| chip drivers/i2c/da7219 |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H16_IRQ)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on end |
| end |
| end # I2C #0 Audio |
| device pci 15.1 off end # I2C #1 |
| device pci 15.2 off end # I2C #2 |
| device pci 15.3 off end # I2C #3 |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT Redirection |
| device pci 16.4 off end # Management Engine Interface 3 |
| device pci 16.5 off end # Management Engine Interface 4 |
| device pci 17.0 off end # SATA |
| device pci 19.0 on # I2C #4 Cam 0 |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI2740"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 2740 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| register "has_power_resource" = "1" |
| |
| register "ssdb.lanes_used" = "2" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "360000000" |
| register "remote_name" = ""IPU0"" |
| |
| #Controls |
| register "clk_panel.clks[0].clknum" = "0" #IMGCLKOUT_3 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D5" #reset |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_B14" #power |
| |
| #_ON |
| register "on_seq.ops_cnt" = "4" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "3" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| |
| device i2c 10 on end |
| end |
| end |
| device pci 19.1 on # I2C #5 Cam 1 and VCM |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM1"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_3 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D4" #power_enable |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_C19" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "4" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "3" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C5.CAM1.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| register "ssdb.lanes_used" = "2" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| device i2c 0C on end |
| end |
| end |
| |
| device pci 19.2 on end # UART #2 |
| device pci 1a.0 on end # eMMC |
| device pci 1c.0 off end # PCI Express Port 1 |
| device pci 1c.1 on end # PCI Express Port 2 - WLAN |
| device pci 1c.2 off end # PCI Express Port 3 |
| device pci 1c.3 off end # PCI Express Port 4 |
| device pci 1c.4 on end # PCI Express Port 5 - NVMe |
| device pci 1c.5 off end # PCI Express Port 6 |
| device pci 1c.6 off end # PCI Express Port 7 |
| device pci 1c.7 off end # PCI Express Port 8 |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.1 off end # UART #1 |
| device pci 1e.2 off end # GSPI #0 |
| device pci 1e.3 on |
| chip drivers/spi/acpi |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cr50"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_H13_IRQ)" |
| device spi 0 on end |
| end |
| end # GSPI #1 |
| device pci 1f.0 on end # eSPI Interface |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 hidden end # Power Management Controller |
| device pci 1f.3 on end # Intel HDA |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.6 off end # GbE |
| end |
| end |