| chip soc/intel/cannonlake |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "PMC_GPP_A" |
| register "gpe0_dw1" = "PMC_GPP_C" |
| register "gpe0_dw2" = "PMC_GPP_D" |
| |
| # EC host command ranges |
| register "gen1_dec" = "0x00040931" # 0x930-0x937 |
| register "gen2_dec" = "0x00040941" # 0x940-0x947 |
| register "gen3_dec" = "0x000c0951" # 0x950-0x95f |
| |
| register "SerialIoDevMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| [PchSerialIoIndexSPI0] = PchSerialIoDisabled, |
| [PchSerialIoIndexSPI1] = PchSerialIoDisabled, |
| [PchSerialIoIndexSPI2] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART0] = PchSerialIoSkipInit, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoDisabled, |
| }" |
| |
| # FSP configuration |
| register "SaGv" = "SaGv_Enabled" |
| register "SkipExtGfxScan" = "1" |
| register "PchPmSlpS3MinAssert" = "3" # 50ms |
| register "PchPmSlpS4MinAssert" = "4" # 4s |
| register "PchPmSlpSusMinAssert" = "4" # 4s |
| register "PchPmSlpAMinAssert" = "4" # 2s |
| register "PchUnlockGpioPads" = "1" |
| # USB2 PHY Power gating |
| register "PchUsb2PhySusPgDisable" = "1" |
| |
| register "s0ix_enable" = "1" |
| register "dptf_enable" = "1" |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 25, |
| .tdp_pl2_override = 51, |
| .psys_pmax = 140, |
| }" |
| register "Device4Enable" = "1" |
| register "AcousticNoiseMitigation" = "1" |
| register "SlowSlewRateForIa" = "2" |
| register "SlowSlewRateForGt" = "2" |
| register "SlowSlewRateForSa" = "0" |
| register "SlowSlewRateForFivr" = "2" |
| # Enable eDP device |
| register "DdiPortEdp" = "1" |
| # Enable HPD for DDI ports B/C |
| register "DdiPortBHpd" = "1" |
| register "DdiPortCHpd" = "1" |
| # Enable DDC for DDI port B |
| register "DdiPortBDdc" = "1" |
| |
| # Disable iDisplay codec enumeration |
| register "PchHdaIDispCodecDisconnect" = "1" |
| register "PchHdaAudioLinkHda" = "1" |
| |
| # Select CPU PL2/PL4 config |
| register "cpu_pl2_4_cfg" = "baseline" |
| |
| # VR Settings Configuration for 2/4 Domains |
| #+----------------+-------+-------+-------+-------+ |
| #| Domain/Setting | SA | IA | GTUS | GTS | |
| #+----------------+-------+-------+-------+-------+ |
| #| Psi1Threshold | 20A | 20A | 20A | 20A | |
| #| Psi2Threshold | 5A | 5A | 5A | 5A | |
| #| Psi3Threshold | 1A | 1A | 1A | 1A | |
| #| Psi3Enable | 1 | 1 | 1 | 1 | |
| #| Psi4Enable | 1 | 1 | 1 | 1 | |
| #| ImonSlope | 0 | 0 | 0 | 0 | |
| #| ImonOffset | 0 | 0 | 0 | 0 | |
| #| IccMax | 6A | 35/70A| 31A | 31A | |
| #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | |
| #| AcLoadline | 10.3 | 1.8 | 3.1 | 3.1 | |
| #| DcLoadline | 10.3 | 1.8 | 3.1 | 3.1 | |
| #+----------------+-------+-------+-------+-------+ |
| register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .icc_max = 0, |
| .voltage_limit = 1520, |
| .ac_loadline = 1030, |
| .dc_loadline = 1030, |
| }" |
| |
| register "domain_vr_config[VR_IA_CORE]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .icc_max = 0, |
| .voltage_limit = 1520, |
| .ac_loadline = 180, |
| .dc_loadline = 180, |
| }" |
| |
| register "domain_vr_config[VR_GT_UNSLICED]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .icc_max = 0, |
| .voltage_limit = 1520, |
| .ac_loadline = 310, |
| .dc_loadline = 310, |
| }" |
| |
| register "domain_vr_config[VR_GT_SLICED]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .icc_max = 0, |
| .voltage_limit = 1520, |
| .ac_loadline = 310, |
| .dc_loadline = 310, |
| }" |
| |
| # Intel Common SoC Config |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Left Type-C Port 1 |
| register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Left Type-C Port 2 |
| register "usb2_ports[2]" = "USB2_PORT_LONG(OC0)" # Right Type-A Port 1 |
| register "usb2_ports[3]" = "USB2_PORT_LONG(OC1)" # Right Type-A Port 2 |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # WWAN |
| register "usb2_ports[5]" = "USB2_PORT_LONG(OC_SKIP)" # Camera |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Left Type-C Port |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)" # Right Type-A Port 1 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Right Type-A Port 2 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Left Type-C Port 2 |
| register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC_SKIP)" # WWAN |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | Touchscreen | |
| #| I2C1 | Touchpad | |
| #| I2C4 | H1 TPM | |
| #+-------------------+---------------------------+ |
| |
| register "tcc_offset" = "1" |
| |
| # PCH Thermal Trip Temperature in deg C |
| register "common_soc_config.pch_thermal_trip" = "77" |
| |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 180, |
| .fall_time_ns = 200, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 30, |
| .fall_time_ns = 80, |
| .data_hold_time_ns = 330, |
| }, |
| .i2c[4] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 30, |
| .fall_time_ns = 60, |
| }, |
| }" |
| |
| # PCIe port 9 for Card Reader |
| register "PcieRpEnable[8]" = "1" |
| register "PcieRpLtrEnable[8]" = "1" |
| register "PcieClkSrcUsage[4]" = "8" |
| register "PcieClkSrcClkReq[4]" = "4" |
| |
| # PCIe port 13 for M.2 2280 SSD |
| register "PcieRpEnable[12]" = "1" |
| register "PcieRpLtrEnable[12]" = "1" |
| register "PcieClkSrcUsage[2]" = "12" |
| register "PcieClkSrcClkReq[2]" = "2" |
| |
| # GPIO PM programming |
| register "gpio_override_pm" = "1" |
| |
| # GPIO community PM configuration |
| # Disable dynamic clock gating; with bits 0-5 set in these registers, |
| # some short interrupt pulses were missed (esp. cr50 irq) |
| register "gpio_pm[COMM_0]" = "0" |
| register "gpio_pm[COMM_1]" = "0" |
| register "gpio_pm[COMM_2]" = "0" |
| register "gpio_pm[COMM_3]" = "0" |
| register "gpio_pm[COMM_4]" = "0" |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on |
| chip drivers/gfx/generic |
| register "device_count" = "1" |
| register "device[0].name" = ""LCD"" |
| # Address is set following the ACPI spec section A.3.2 |
| # for an internal panel on the first port of the graphics chip |
| register "device[0].addr" = "0x80010400" |
| register "device[0].privacy.enabled" = "1" |
| register "device[0].privacy.detect_function" = ""\\_SB.PCI0.LPCB.EC0.GPVD"" |
| register "device[0].privacy.status_function" = ""\\_SB.PCI0.LPCB.EC0.GPVX"" |
| register "device[0].privacy.enable_function" = ""\\_SB.PCI0.LPCB.EC0.EPVX"" |
| register "device[0].privacy.disable_function" = ""\\_SB.PCI0.LPCB.EC0.DPVX"" |
| device generic 0 on end |
| end |
| end # Integrated Graphics Device |
| device pci 04.0 on end # SA Thermal device |
| device pci 12.0 on end # Thermal Subsystem |
| device pci 12.5 off end # UFS SCS |
| device pci 12.6 off end # GSPI #2 |
| device pci 13.0 on # Integrated Sensor Hub |
| chip drivers/intel/ish |
| register "firmware_name" = ""drallion_ish.bin"" |
| device generic 0 on end |
| end |
| end |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 2.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 2.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H15)" |
| device usb 2.9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 3.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 3.4 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.3 on |
| chip drivers/wifi/generic |
| register "wake" = "PME_B0_EN_BIT" |
| device generic 0 on end |
| end |
| end # CNVi wifi |
| device pci 14.5 off end # SDCard |
| device pci 15.0 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""WCOM48E2"" |
| register "generic.desc" = ""Wacom Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C23_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "generic.reset_delay_ms" = "10" |
| register "generic.reset_off_delay_ms" = "5" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)" |
| register "generic.stop_delay_ms" = "20" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" |
| register "generic.enable_delay_ms" = "55" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x1" |
| register "generic.device_present_gpio" = "GPP_B4" |
| register "generic.device_present_gpio_invert" = "1" |
| device i2c 0A on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN900C"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C23_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "generic.reset_delay_ms" = "10" |
| register "generic.reset_off_delay_ms" = "5" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)" |
| register "generic.stop_delay_ms" = "10" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" |
| register "generic.enable_delay_ms" = "55" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| register "generic.device_present_gpio" = "GPP_B4" |
| register "generic.device_present_gpio_invert" = "1" |
| device i2c 10 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""MLFS0000"" |
| register "desc" = ""Melfas Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_C23_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" |
| register "reset_delay_ms" = "10" |
| register "reset_off_delay_ms" = "5" |
| register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)" |
| register "stop_delay_ms" = "115" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" |
| register "enable_delay_ms" = "55" |
| register "has_power_resource" = "1" |
| register "device_present_gpio" = "GPP_B4" |
| register "device_present_gpio_invert" = "1" |
| device i2c 34 on end |
| end |
| end # I2C #0 |
| device pci 15.1 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)" |
| register "probed" = "1" |
| device i2c 2c on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end # I2C #1 |
| device pci 15.2 off end # I2C #2 |
| device pci 15.3 off end # I2C #3 |
| device pci 16.0 off end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT Redirection |
| device pci 16.4 off end # Management Engine Interface 3 |
| device pci 16.5 off end # Management Engine Interface 4 |
| device pci 17.0 off end # SATA |
| device pci 19.0 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D18_IRQ)" |
| device i2c 50 on end |
| end |
| end # I2C #4 |
| device pci 19.1 off end # I2C #5 |
| device pci 19.2 off end # UART #2 |
| device pci 1a.0 off end # eMMC |
| device pci 1c.0 off end # PCI Express Port 1 (USB) |
| device pci 1c.1 off end # PCI Express Port 2 (USB) |
| device pci 1c.2 off end # PCI Express Port 3 (USB) |
| device pci 1c.3 off end # PCI Express Port 4 (USB) |
| device pci 1c.4 off end # PCI Express Port 5 (USB) |
| device pci 1c.5 off end # PCI Express Port 6 |
| device pci 1c.6 off end # PCI Express Port 7 |
| device pci 1c.7 off end # PCI Express Port 8 |
| device pci 1d.0 on |
| smbios_slot_desc "SlotTypeM2Socket1_SD" "SlotLengthOther" "2230" "SlotDataBusWidth1X" |
| register "PcieRpSlotImplemented[8]" = "1" |
| end # PCI Express Port 9 |
| device pci 1d.1 off end # PCI Express Port 10 |
| device pci 1d.2 off end # PCI Express Port 11 |
| device pci 1d.3 off end # PCI Express Port 12 |
| device pci 1d.4 on |
| smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" "2280" "SlotDataBusWidth4X" |
| register "PcieRpSlotImplemented[12]" = "1" |
| end # PCI Express Port 13 (x4) |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.1 off end # UART #1 |
| device pci 1e.2 off end # GSPI #0 |
| device pci 1e.3 off end # GSPI #1 |
| device pci 1f.0 on |
| chip ec/google/wilco |
| device pnp 0c09.0 on end |
| end |
| end # LPC/eSPI |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 on end # Power Management Controller |
| device pci 1f.3 on end # Intel HDA |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.6 off end # GbE |
| end |
| end |