| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <arch/io.h> |
| #include <bootstate.h> |
| #include <cf9_reset.h> |
| #include <device/pci_def.h> |
| #include <device/pci_ids.h> |
| #include <device/pci_ops.h> |
| #include <gpio.h> |
| #include <hwilib.h> |
| #include <intelblocks/lpc_lib.h> |
| #include <intelblocks/pcr.h> |
| #include <soc/pcr_ids.h> |
| #include <baseboard/variants.h> |
| #include <types.h> |
| |
| #define TX_DWORD3 0xa8c |
| |
| void variant_mainboard_final(void) |
| { |
| struct device *dev = NULL; |
| |
| /* PIR6 register mapping for PCIe root ports |
| * INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#-> PIRQC# |
| */ |
| pcr_write16(PID_ITSS, 0x314c, 0x2103); |
| |
| /* Enable CLKRUN_EN for power gating LPC */ |
| lpc_enable_pci_clk_cntl(); |
| |
| /* |
| * Enable LPC PCE (Power Control Enable) by setting IOSF-SB port 0xD2 |
| * offset 0x341D bit3 and bit0. |
| * Enable LPC CCE (Clock Control Enable) by setting IOSF-SB port 0xD2 |
| * offset 0x341C bit [3:0]. |
| */ |
| pcr_or32(PID_LPC, PCR_LPC_PRC, (PCR_LPC_CCE_EN | PCR_LPC_PCE_EN)); |
| |
| /* Set Master Enable for on-board PCI device. */ |
| dev = dev_find_device(PCI_VENDOR_ID_SIEMENS, 0x403e, 0); |
| if (dev) { |
| pci_or_config16(dev, PCI_COMMAND, PCI_COMMAND_MASTER); |
| |
| /* Disable clock outputs 0 and 2-4 (CLKOUT) for upstream |
| * XIO2001 PCIe to PCI Bridge. |
| */ |
| struct device *parent = dev->bus->dev; |
| if (parent && parent->device == PCI_DEVICE_ID_TI_XIO2001) |
| pci_write_config8(parent, 0xd8, 0x1d); |
| } |
| |
| /* Disable clock outputs 2-5 (CLKOUT) for another XIO2001 PCIe to PCI |
| * Bridge on this mainboard. |
| */ |
| dev = dev_find_device(PCI_VENDOR_ID_SIEMENS, 0x403f, 0); |
| if (dev) { |
| struct device *parent = dev->bus->dev; |
| if (parent && parent->device == PCI_DEVICE_ID_TI_XIO2001) |
| pci_write_config8(parent, 0xd8, 0x3c); |
| } |
| |
| /* Set Full Reset Bit in Reset Control Register (I/O port CF9h). |
| * When Bit 3 is set to 1 and then the reset button is pressed the PCH |
| * will drive SLP_S3 active (low). SLP_S3 is then used on the mainboard |
| * to generate the right reset timing. |
| */ |
| outb(FULL_RST, RST_CNT); |
| } |
| |
| static void finalize_boot(void *unused) |
| { |
| /* Set coreboot ready LED. */ |
| gpio_output(CNV_RGI_DT, 1); |
| } |
| |
| BOOT_STATE_INIT_ENTRY(BS_PAYLOAD_BOOT, BS_ON_ENTRY, finalize_boot, NULL); |