lenovo/t420/4.8-2488-gb1baa980ea/2018-12-08T16_13_46Z/coreboot_console.txt

*** Pre-CBMEM romstage console overflowed, log truncated! ***

Found compatible clock, CAS pair.
Selected DRAM frequency: 666 MHz
Selected CAS latency   : 9T
PLL busy... done in 60 us
MCU frequency is set at : 666 MHz
Done dimm mapping
Update PCI-E configuration space:
PCI(0, 0, 0)[a0] = 0
PCI(0, 0, 0)[a4] = 2
PCI(0, 0, 0)[bc] = 82a00000
PCI(0, 0, 0)[a8] = 7b600000
PCI(0, 0, 0)[ac] = 2
PCI(0, 0, 0)[b8] = 80000000
PCI(0, 0, 0)[b0] = 80a00000
PCI(0, 0, 0)[b4] = 80800000
PCI(0, 0, 0)[7c] = 7f
PCI(0, 0, 0)[70] = fe000000
PCI(0, 0, 0)[74] = 1
PCI(0, 0, 0)[78] = fe000c00
Done memory map
Done io registers
t123: 1912, 9120, 500
ME: FW Partition Table      : OK
ME: Bringup Loader Failure  : NO
ME: Firmware Init Complete  : YES
ME: Manufacturing Mode      : NO
ME: Boot Options Present    : NO
ME: Update In Progress      : NO
ME: Current Working State   : Normal
ME: Current Operation State : M0 without UMA
ME: Current Operation Mode  : Normal
ME: Error Code              : No Error
ME: Progress Phase          : Policy Module
ME: Power Management Event  : Non-power cycle reset
ME: Progress Phase State    : Entery into Policy Module
ME: FWS2: 0x39000006
ME:  Bist in progress: 0x0
ME:  ICC Status      : 0x3
ME:  Invoke MEBx     : 0x0
ME:  CPU replaced    : 0x0
ME:  MBP ready       : 0x0
ME:  MFS failure     : 0x0
ME:  Warm reset req  : 0x0
ME:  CPU repl valid  : 0x0
ME:  (Reserved)      : 0x0
ME:  FW update req   : 0x0
ME:  (Reserved)      : 0x0
ME:  Current state   : 0x0
ME:  Current PM event: 0x9
ME:  Progress code   : 0x3
Waited long enough, or CPU was not replaced, continue...
PASSED! Tell ME that DRAM is ready
ME: FWS2: 0x390b0006
ME:  Bist in progress: 0x0
ME:  ICC Status      : 0x3
ME:  Invoke MEBx     : 0x0
ME:  CPU replaced    : 0x0
ME:  MBP ready       : 0x0
ME:  MFS failure     : 0x0
ME:  Warm reset req  : 0x0
ME:  CPU repl valid  : 0x0
ME:  (Reserved)      : 0x0
ME:  FW update req   : 0x0
ME:  (Reserved)      : 0x0
ME:  Current state   : 0xb
ME:  Current PM event: 0x9
ME:  Progress code   : 0x3
ME: Requested BIOS Action: Continue to boot
ME: FW Partition Table      : OK
ME: Bringup Loader Failure  : NO
ME: Firmware Init Complete  : NO
ME: Manufacturing Mode      : NO
ME: Boot Options Present    : NO
ME: Update In Progress      : NO
ME: Current Working State   : Normal
ME: Current Operation State : M0 without UMA
ME: Current Operation Mode  : Normal
ME: Error Code              : No Error
ME: Progress Phase          : Policy Module
ME: Power Management Event  : Non-power cycle reset
ME: Progress Phase State    : Received DRAM Init Done
memcfg DDR3 ref clock 133 MHz
memcfg DDR3 clock 1330 MHz
memcfg channel assignment: A: 0, B  1, C  2
memcfg channel[0] config (00620010):
   ECC inactive
   enhanced interleave mode on
   rank interleave on
   DIMMA 4096 MB width x8 dual rank, selected
   DIMMB 0 MB width x8 single rank
memcfg channel[1] config (00620010):
   ECC inactive
   enhanced interleave mode on
   rank interleave on
   DIMMA 4096 MB width x8 dual rank, selected
   DIMMB 0 MB width x8 single rank
CBMEM:
IMD: root @ 7ffff000 254 entries.
IMD: root @ 7fffec00 62 entries.
External stage cache:
IMD: root @ 803ff000 254 entries.
IMD: root @ 803fec00 62 entries.
CBMEM entry for DIMM info: 0x7fffea40
MTRR Range: Start=ff800000 End=0 (Size 800000)
MTRR Range: Start=0 End=1000000 (Size 1000000)
MTRR Range: Start=7f800000 End=80000000 (Size 800000)
MTRR Range: Start=80000000 End=80800000 (Size 800000)
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'fallback/postcar'
CBFS: Found @ offset 3a1c0 size 3ba0
Decompressing stage fallback/postcar @ 0x7ffcffc0 (31888 bytes)
Loading module at 7ffd0000 with entry 7ffd0000. filesize: 0x3990 memsize: 0x7c50
Processing 109 relocs. Offset value of 0x7dfd0000


coreboot-4.8-2488-gb1baa980ea Sat Dec  8 16:13:46 UTC 2018 postcar starting...
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'fallback/ramstage'
CBFS: Found @ offset 19cc0 size 18731
Decompressing stage fallback/ramstage @ 0x7ff86fc0 (293464 bytes)
Loading module at 7ff87000 with entry 7ff87000. filesize: 0x33810 memsize: 0x47a18
Processing 3454 relocs. Offset value of 0x7f187000


coreboot-4.8-2488-gb1baa980ea Sat Dec  8 16:13:46 UTC 2018 ramstage starting...
Normal boot.
BS: BS_PRE_DEVICE times (us): entry 0 run 2 exit 0
BS: BS_DEV_INIT_CHIPS times (us): entry 0 run 3 exit 0
Enumerating buses...
CPU_CLUSTER: 0 enabled
DOMAIN: 0000 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [8086/0104] enabled
PCI: Static device PCI: 00:01.0 not found, disabling it.
PCI: 00:02.0 [8086/0126] enabled
PCI: 00:04.0 [8086/0103] enabled
PCI: 00:16.0: Disabling device
PCI: 00:16.0 [8086/1c3a] disabled
PCI: 00:16.1: Disabling device
PCI: 00:16.2: Disabling device
PCI: 00:16.3: Disabling device
PCI: 00:19.0 [8086/1502] enabled
PCI: 00:1a.0 [8086/1c2d] enabled
PCI: 00:1b.0 [8086/1c20] enabled
PCH: PCIe Root Port coalescing is enabled
PCI: 00:1c.0: Disabling device
PCI: 00:1c.0: check set enabled
PCH: Remap PCIe function 1 to 0
PCI: 00:1c.1 [8086/1c12] enabled
PCI: 00:1c.2: Disabling device
PCH: Remap PCIe function 3 to 0
PCI: 00:1c.3 [8086/1c16] enabled
PCH: Remap PCIe function 4 to 0
PCI: 00:1c.4 [8086/1c18] enabled
PCI: 00:1c.5: Disabling device
PCI: 00:1c.6: Disabling device
PCI: 00:1c.7: Disabling device
PCH: PCIe map 1c.0 -> 1c.4
PCH: PCIe map 1c.1 -> 1c.0
PCH: PCIe map 1c.3 -> 1c.1
PCH: PCIe map 1c.4 -> 1c.3
PCI: 00:1d.0 [8086/1c26] enabled
PCI: 00:1e.0: Disabling device
PCI: 00:1e.0 [8086/2448] disabled
PCI: 00:1f.0 [8086/1c4f] enabled
PCI: 00:1f.2 [8086/1c01] enabled
PCI: 00:1f.3 [8086/1c22] enabled
PCI: 00:1f.5: Disabling device
PCI: 00:1f.5 [8086/1c09] disabled No operations
PCI: 00:1f.6 [8086/1c24] enabled
PCI: pci_scan_bus for bus 01
PCI: 01:00.0 [8086/4238] enabled
Enabling Common Clock Configuration
ASPM: Enabled L0s and L1
Failed to enable LTR for dev = PCI: 01:00.0
scan_bus: scanning of bus PCI: 00:1c.0 took 301 usecs
PCI: pci_scan_bus for bus 02
scan_bus: scanning of bus PCI: 00:1c.1 took 53 usecs
PCI: pci_scan_bus for bus 03
PCI: 03:00.0 [1180/e822] enabled
Enabling Common Clock Configuration
ASPM: Enabled L0s and L1
Failed to enable LTR for dev = PCI: 03:00.0
scan_bus: scanning of bus PCI: 00:1c.3 took 246 usecs
PMH7: ID 04 Revision 01
PNP: 00ff.1 enabled
PNP: 0c31.0 enabled
EC Firmware ID 83HT27WW-3.20, Version 1.01B
H8: BDC installed
H8: WWAN detection not implemented. Assuming WWAN installed
PNP: 00ff.2 enabled
Hybrid graphics: Not installed
PNP: 00ff.f disabled
scan_bus: scanning of bus PCI: 00:1f.0 took 5115 usecs
bus: PCI: 00:1f.3[0]->I2C: 01:54 enabled
bus: PCI: 00:1f.3[0]->I2C: 01:55 enabled
bus: PCI: 00:1f.3[0]->I2C: 01:56 enabled
bus: PCI: 00:1f.3[0]->I2C: 01:57 enabled
bus: PCI: 00:1f.3[0]->I2C: 01:5c enabled
bus: PCI: 00:1f.3[0]->I2C: 01:5d enabled
bus: PCI: 00:1f.3[0]->I2C: 01:5e enabled
bus: PCI: 00:1f.3[0]->I2C: 01:5f enabled
scan_bus: scanning of bus PCI: 00:1f.3 took 26 usecs
scan_bus: scanning of bus DOMAIN: 0000 took 6046 usecs
scan_bus: scanning of bus Root Device took 6053 usecs
done
FMAP: Found "FLASH" version 1.1 at 700000.
FMAP: base = ff800000 size = 800000 #areas = 4
FMAP: area RW_MRC_CACHE found @ 710000 (65536 bytes)
MRC: No data in cbmem for 'RW_MRC_CACHE'.
BS: BS_DEV_ENUMERATE times (us): entry 0 run 6090 exit 25
found VGA at PCI: 00:02.0
Setting up VGA for PCI: 00:02.0
Setting PCI_BRIDGE_CTL_VGA for bridge DOMAIN: 0000
Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
Allocating resources...
Reading resources...
Adding PCIe enhanced config space BAR 0xf0000000-0xf4000000.
PNP: 00ff.1 missing read_resources
PNP: 00ff.2 missing read_resources
Done reading resources.
skipping PNP: 00ff.2@60 fixed resource, size=0!
skipping PNP: 00ff.2@62 fixed resource, size=0!
skipping PNP: 00ff.2@64 fixed resource, size=0!
skipping PNP: 00ff.2@66 fixed resource, size=0!
Setting resources...
TOUUD 0x27b600000 TOLUD 0x82a00000 TOM 0x200000000
MEBASE 0x1fe000000
IGD decoded, subtracting 32M UMA and 2M GTT
TSEG base 0x80000000 size 8M
Available memory below 4GB: 2048M
Available memory above 4GB: 6070M
PCI: 00:02.0 10 <- [0x00e1000000 - 0x00e13fffff] size 0x00400000 gran 0x16 mem64
PCI: 00:02.0 18 <- [0x00d0000000 - 0x00dfffffff] size 0x10000000 gran 0x1c prefmem64
PCI: 00:02.0 20 <- [0x0000003000 - 0x000000303f] size 0x00000040 gran 0x06 io
PCI: 00:04.0 10 <- [0x00e1620000 - 0x00e1627fff] size 0x00008000 gran 0x0f mem64
PCI: 00:19.0 10 <- [0x00e1600000 - 0x00e161ffff] size 0x00020000 gran 0x11 mem
PCI: 00:19.0 14 <- [0x00e162c000 - 0x00e162cfff] size 0x00001000 gran 0x0c mem
PCI: 00:19.0 18 <- [0x0000003040 - 0x000000305f] size 0x00000020 gran 0x05 io
PCI: 00:1a.0 10 <- [0x00e162f000 - 0x00e162f3ff] size 0x00000400 gran 0x0a mem
PCI: 00:1b.0 10 <- [0x00e1628000 - 0x00e162bfff] size 0x00004000 gran 0x0e mem64
PCI: 00:1c.0 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 01 io
PCI: 00:1c.0 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 01 prefmem
PCI: 00:1c.0 20 <- [0x00e1400000 - 0x00e14fffff] size 0x00100000 gran 0x14 bus 01 mem
PCI: 01:00.0 10 <- [0x00e1400000 - 0x00e1401fff] size 0x00002000 gran 0x0d mem64
PCI: 00:1c.1 1c <- [0x0000002000 - 0x0000002fff] size 0x00001000 gran 0x0c bus 02 io
PCI: 00:1c.1 24 <- [0x00e0000000 - 0x00e07fffff] size 0x00800000 gran 0x14 bus 02 prefmem
PCI: 00:1c.1 20 <- [0x00e0800000 - 0x00e0ffffff] size 0x00800000 gran 0x14 bus 02 mem
NONE missing set_resources
PCI: 00:1c.3 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 03 io
PCI: 00:1c.3 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 03 prefmem
PCI: 00:1c.3 20 <- [0x00e1500000 - 0x00e15fffff] size 0x00100000 gran 0x14 bus 03 mem
PCI: 03:00.0 10 <- [0x00e1500000 - 0x00e15000ff] size 0x00000100 gran 0x08 mem
PCI: 00:1d.0 10 <- [0x00e1630000 - 0x00e16303ff] size 0x00000400 gran 0x0a mem
PNP: 00ff.1 missing set_resources
PNP: 00ff.2 missing set_resources
PCI: 00:1f.2 10 <- [0x0000003080 - 0x0000003087] size 0x00000008 gran 0x03 io
PCI: 00:1f.2 14 <- [0x0000003090 - 0x0000003093] size 0x00000004 gran 0x02 io
PCI: 00:1f.2 18 <- [0x0000003088 - 0x000000308f] size 0x00000008 gran 0x03 io
PCI: 00:1f.2 1c <- [0x0000003094 - 0x0000003097] size 0x00000004 gran 0x02 io
PCI: 00:1f.2 20 <- [0x0000003060 - 0x000000307f] size 0x00000020 gran 0x05 io
PCI: 00:1f.2 24 <- [0x00e162e000 - 0x00e162e7ff] size 0x00000800 gran 0x0b mem
PCI: 00:1f.3 10 <- [0x00e1631000 - 0x00e16310ff] size 0x00000100 gran 0x08 mem64
PCI: 00:1f.6 10 <- [0x00e162d000 - 0x00e162dfff] size 0x00001000 gran 0x0c mem64
Done setting resources.
Done allocating resources.
BS: BS_DEV_RESOURCES times (us): entry 0 run 1651 exit 0
Enabling resources...
PCI: 00:00.0 subsystem <- 17aa/21ce
PCI: 00:00.0 cmd <- 06
PCI: 00:02.0 subsystem <- 17aa/21ce
PCI: 00:02.0 cmd <- 03
PCI: 00:04.0 cmd <- 02
PCI: 00:19.0 subsystem <- 17aa/21ce
PCI: 00:19.0 cmd <- 103
PCI: 00:1a.0 subsystem <- 17aa/21ce
PCI: 00:1a.0 cmd <- 102
PCI: 00:1b.0 subsystem <- 17aa/21ce
PCI: 00:1b.0 cmd <- 102
PCI: 00:1c.0 bridge ctrl <- 0003
PCI: 00:1c.0 subsystem <- 17aa/21ce
PCI: 00:1c.0 cmd <- 106
PCI: 00:1c.1 bridge ctrl <- 0003
PCI: 00:1c.1 subsystem <- 17aa/21ce
PCI: 00:1c.1 cmd <- 107
PCI: 00:1c.3 bridge ctrl <- 0003
PCI: 00:1c.3 subsystem <- 17aa/21ce
PCI: 00:1c.3 cmd <- 106
PCI: 00:1d.0 subsystem <- 17aa/21ce
PCI: 00:1d.0 cmd <- 102
pch_decode_init
PCI: 00:1f.0 subsystem <- 17aa/21ce
PCI: 00:1f.0 cmd <- 107
PCI: 00:1f.2 subsystem <- 17aa/21ce
PCI: 00:1f.2 cmd <- 03
PCI: 00:1f.3 subsystem <- 17aa/21ce
PCI: 00:1f.3 cmd <- 103
PCI: 00:1f.6 subsystem <- 17aa/21ce
PCI: 00:1f.6 cmd <- 02
PCI: 01:00.0 cmd <- 02
PCI: 03:00.0 subsystem <- 17aa/21ce
PCI: 03:00.0 cmd <- 06
done.
BS: BS_DEV_ENABLE times (us): entry 0 run 176 exit 0
Found TPM ST33ZP24 by ST Microelectronics
TPM: Startup
TPM: command 0x99 returned 0x0
TPM: Asserting physical presence
TPM: command 0x4000000a returned 0x0
TPM: command 0x65 returned 0x0
TPM: flags disable=0, deactivated=0, nvlocked=1
TPM: setup succeeded
Initializing devices...
Root Device init ...
Root Device init finished in 1 usecs
CPU_CLUSTER: 0 init ...
start_eip=0x00001000, code_size=0x00000031
Setting up SMI for CPU
Loading module at 00038000 with entry 00038000. filesize: 0x1a8 memsize: 0x1a8
Processing 13 relocs. Offset value of 0x00038000
SMM Module: stub loaded at 00038000. Will call 7ffa3684(7ffca8e0)
Installing SMM handler to 0x80000000
Loading module at 80010000 with entry 80010112. filesize: 0x1350 memsize: 0x5370
Processing 48 relocs. Offset value of 0x80010000
Loading module at 80008000 with entry 80008000. filesize: 0x1a8 memsize: 0x1a8
Processing 13 relocs. Offset value of 0x80008000
SMM Module: placing jmp sequence at 80007c00 rel16 0x03fd
SMM Module: placing jmp sequence at 80007800 rel16 0x07fd
SMM Module: placing jmp sequence at 80007400 rel16 0x0bfd
SMM Module: stub loaded at 80008000. Will call 80010112(00000000)
Initializing southbridge SMI...
SMI_STS: MCSMI 
GPE0_STS: GPIO15 GPIO14 GPIO13 GPIO11 GPIO10 GPIO9 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO1 GPIO0 
ALT_GP_SMI_STS: GPI14 GPI13 GPI11 GPI10 GPI9 GPI7 GPI6 GPI5 GPI4 GPI3 GPI1 GPI0 
TCO_STS: 
In relocation handler: cpu 0
New SMBASE=0x80000000 IEDBASE=0x80400000 @ 0003fc00
Writing SMRR. base = 0x80000006, mask=0xff800800
Relocation complete.
Locking SMM.
Initializing CPU #0
CPU: vendor Intel device 206a7
CPU: family 06, model 2a, stepping 07
Enabling cache
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'cpu_microcode_blob.bin'
CBFS: Found @ offset 13840 size 6400
microcode: sig=0x206a7 pf=0x10 revision=0x2d
CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz.
CPU: platform id 4
CPU: cpuid(1) 0x206a7
CPU: AES supported
CPU: TXT supported
CPU: VT supported
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000027b600000 size 0x17b600000 type 6
MTRR: Fixed MSR 0x250 0x0606060606060606
MTRR: Fixed MSR 0x258 0x0606060606060606
MTRR: Fixed MSR 0x259 0x0000000000000000
MTRR: Fixed MSR 0x268 0x0606060606060606
MTRR: Fixed MSR 0x269 0x0606060606060606
MTRR: Fixed MSR 0x26a 0x0606060606060606
MTRR: Fixed MSR 0x26b 0x0606060606060606
MTRR: Fixed MSR 0x26c 0x0606060606060606
MTRR: Fixed MSR 0x26d 0x0606060606060606
MTRR: Fixed MSR 0x26e 0x0606060606060606
MTRR: Fixed MSR 0x26f 0x0606060606060606
CPU physical address size: 36 bits
MTRR: default type WB/UC MTRR counts: 4/4.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000000f80000000 type 6
MTRR: 1 base 0x00000000d0000000 mask 0x0000000ff0000000 type 1
MTRR: 2 base 0x0000000100000000 mask 0x0000000f00000000 type 6
MTRR: 3 base 0x0000000200000000 mask 0x0000000f80000000 type 6

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Setting up local APIC... apic_id: 0x00 done.
VMX is locked, so set_vmx will do nothing
model_x06ax: energy policy set to 6
model_x06ax: frequency set to 2800
Turbo is available but hidden
Turbo has been enabled
CPU: 0 has 2 cores, 2 threads per core
CPU: 0 has core 1
In relocation handler: cpu 1
New SMBASE=0x7ffffc00 IEDBASE=0x80400000 @ 0003fc00
Writing SMRR. base = 0x80000006, mask=0xff800800
Initializing CPU #1
CPU: 0 has core 2
CPU: vendor Intel device 206a7
CPU: family 06, model 2a, stepping 07
Enabling cache
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'cpu_microcode_blob.bin'
CBFS: Found @ offset 13840 size 6400
microcode: sig=0x206a7 pf=0x10 revision=0x2d
CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz.
CPU: platform id 4
CPU: cpuid(1) 0x206a7
CPU: AES supported
CPU: TXT supported
CPU: VT supported
MTRR: Fixed MSR 0x250 0x0606060606060606
MTRR: Fixed MSR 0x258 0x0606060606060606
MTRR: Fixed MSR 0x259 0x0000000000000000
MTRR: Fixed MSR 0x268 0x0606060606060606
MTRR: Fixed MSR 0x269 0x0606060606060606
MTRR: Fixed MSR 0x26a 0x0606060606060606
MTRR: Fixed MSR 0x26b 0x0606060606060606
MTRR: Fixed MSR 0x26c 0x0606060606060606
MTRR: Fixed MSR 0x26d 0x0606060606060606
MTRR: Fixed MSR 0x26e 0x0606060606060606
MTRR: Fixed MSR 0x26f 0x0606060606060606
CPU physical address size: 36 bits

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Setting up local APIC... apic_id: 0x01 done.
VMX is locked, so set_vmx will do nothing
model_x06ax: energy policy set to 6
model_x06ax: frequency set to 2800
CPU #1 initialized
In relocation handler: cpu 2
New SMBASE=0x7ffff800 IEDBASE=0x80400000 @ 0003fc00
Writing SMRR. base = 0x80000006, mask=0xff800800
CPU: 0 has core 3
Initializing CPU #2
CPU: vendor Intel device 206a7
CPU: family 06, model 2a, stepping 07
Enabling cache
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'cpu_microcode_blob.bin'
CBFS: Found @ offset 13840 size 6400
microcode: sig=0x206a7 pf=0x10 revision=0x0
microcode: updated to revision 0x2d date=2018-02-07
CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz.
CPU: platform id 4
CPU: cpuid(1) 0x206a7
CPU: AES supported
CPU: TXT supported
CPU: VT supported
MTRR: Fixed MSR 0x250 0x0606060606060606
MTRR: Fixed MSR 0x258 0x0606060606060606
MTRR: Fixed MSR 0x259 0x0000000000000000
MTRR: Fixed MSR 0x268 0x0606060606060606
MTRR: Fixed MSR 0x269 0x0606060606060606
MTRR: Fixed MSR 0x26a 0x0606060606060606
MTRR: Fixed MSR 0x26b 0x0606060606060606
MTRR: Fixed MSR 0x26c 0x0606060606060606
MTRR: Fixed MSR 0x26d 0x0606060606060606
MTRR: Fixed MSR 0x26e 0x0606060606060606
MTRR: Fixed MSR 0x26f 0x0606060606060606
CPU physical address size: 36 bits

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Setting up local APIC... apic_id: 0x02 done.
VMX is locked, so set_vmx will do nothing
model_x06ax: energy policy set to 6
model_x06ax: frequency set to 2800
CPU #2 initialized
In relocation handler: cpu 3
New SMBASE=0x7ffff400 IEDBASE=0x80400000 @ 0003fc00
Writing SMRR. base = 0x80000006, mask=0xff800800
CPU #0 initialized
Waiting for 1 CPUS to stop
Initializing CPU #3
CPU: vendor Intel device 206a7
CPU: family 06, model 2a, stepping 07
Enabling cache
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'cpu_microcode_blob.bin'
CBFS: Found @ offset 13840 size 6400
microcode: sig=0x206a7 pf=0x10 revision=0x2d
CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz.
CPU: platform id 4
CPU: cpuid(1) 0x206a7
CPU: AES supported
CPU: TXT supported
CPU: VT supported
MTRR: Fixed MSR 0x250 0x0606060606060606
MTRR: Fixed MSR 0x258 0x0606060606060606
MTRR: Fixed MSR 0x259 0x0000000000000000
MTRR: Fixed MSR 0x268 0x0606060606060606
MTRR: Fixed MSR 0x269 0x0606060606060606
MTRR: Fixed MSR 0x26a 0x0606060606060606
MTRR: Fixed MSR 0x26b 0x0606060606060606
MTRR: Fixed MSR 0x26c 0x0606060606060606
MTRR: Fixed MSR 0x26d 0x0606060606060606
MTRR: Fixed MSR 0x26e 0x0606060606060606
MTRR: Fixed MSR 0x26f 0x0606060606060606
CPU physical address size: 36 bits

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Setting up local APIC... apic_id: 0x03 done.
VMX is locked, so set_vmx will do nothing
model_x06ax: energy policy set to 6
model_x06ax: frequency set to 2800
CPU #3 initialized
All AP CPUs stopped (627 loops)
CPU_CLUSTER: 0 init finished in 61423 usecs
PCI: 00:00.0 init ...
Disabling PEG12.
Disabling PEG11.
Disabling PEG10.
Disabling PEG60.
Disabling Device 7.
Disabling PEG IO clock.
Set BIOS_RESET_CPL
CPU TDP: 35 Watts
PCI: 00:00.0 init finished in 1019 usecs
PCI: 00:02.0 init ...
GT Power Management Init
SNB GT2 Power Meter Weights
GT Power Management Init (post VBIOS)
bringing up panel at resolution 1600 x 900
Borders 0 x 0
Blank 410 x 12
Sync 42 x 3
Front porch 64 x 3
Spread spectrum clock
Dual channel
Polarities 1, 1
Data M1=1922389, N1=8388608
Link frequency 270000 kHz
Link M1=213598, N1=524288
Pixel N=6, M1=14, M2=7, P1=2
Pixel clock 110000 kHz
waiting for panel powerup
panel powered up
PCI: 00:02.0 init finished in 27906 usecs
PCI: 00:04.0 init ...
PCI: 00:04.0 init finished in 0 usecs
PCI: 00:19.0 init ...
PCI: 00:19.0 init finished in 0 usecs
PCI: 00:1a.0 init ...
EHCI: Setting up controller.. done.
PCI: 00:1a.0 init finished in 13 usecs
PCI: 00:1b.0 init ...
Azalia: base = e1628000
Azalia: codec_mask = 0b
Azalia: Initializing codec #3
Azalia: codec viddid: 80862805
Azalia: No verb!
Azalia: Initializing codec #1
Azalia: codec viddid: 14f12c06
Azalia: No verb!
Azalia: Initializing codec #0
Azalia: codec viddid: 14f1506e
Azalia: verb_size: 52
Azalia: verb loaded.
PCI: 00:1b.0 init finished in 4345 usecs
PCI: 00:1c.0 init ...
Initializing PCH PCIe bridge.
PCI: 00:1c.0 init finished in 9 usecs
PCI: 00:1c.1 init ...
Initializing PCH PCIe bridge.
PCI: 00:1c.1 init finished in 12 usecs
PCI: 00:1c.3 init ...
Initializing PCH PCIe bridge.
PCI: 00:1c.3 init finished in 9 usecs
PCI: 00:1d.0 init ...
EHCI: Setting up controller.. done.
PCI: 00:1d.0 init finished in 11 usecs
PCI: 00:1f.0 init ...
pch: lpc_init
PCH: detected QM67, device id: 0x1c4f, rev id 0x5
IOAPIC: Initializing IOAPIC at 0xfec00000
IOAPIC: Bootstrap Processor Local APIC = 0x00
IOAPIC: ID = 0x02
Set power off after power failure.
NMI sources disabled.
CougarPoint PM init
RTC: failed = 0x0
RTC Init
Disabling ACPI via APMC:
done.
pch_spi_init
PCI: 00:1f.0 init finished in 364 usecs
PCI: 00:1f.2 init ...
SATA: Initializing...
SATA: Controller in AHCI mode.
ABAR: e162e000
PCI: 00:1f.2 init finished in 93 usecs
PCI: 00:1f.3 init ...
PCI: 00:1f.3 init finished in 7 usecs
PCI: 00:1f.6 init ...
PCI: 00:1f.6 init finished in 0 usecs
PCI: 01:00.0 init ...
PCI: 01:00.0 init finished in 0 usecs
PCI: 03:00.0 init ...
PCI: 03:00.0 init finished in 14 usecs
PNP: 00ff.2 init ...
PNP: 00ff.2 init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:54 init ...
I2C: 01:54 init finished in 1 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:55 init ...
I2C: 01:55 init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:56 init ...
I2C: 01:56 init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:57 init ...
I2C: 01:57 init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:5c init ...
Locking EEPROM RFID
init EEPROM done
I2C: 01:5c init finished in 22801 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:5d init ...
I2C: 01:5d init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:5e init ...
I2C: 01:5e init finished in 0 usecs
smbus: PCI: 00:1f.3[0]->I2C: 01:5f init ...
I2C: 01:5f init finished in 0 usecs
Devices initialized
BS: BS_DEV_INIT times (us): entry 15836 run 118152 exit 0
Finalize devices...
PCI: 00:1f.0 final
Devices finalized
BS: BS_POST_DEVICE times (us): entry 0 run 46 exit 0
BS: BS_OS_RESUME_CHECK times (us): entry 0 run 3 exit 0
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'fallback/dsdt.aml'
CBFS: Found @ offset 3ddc0 size 35d2
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'fallback/slic'
CBFS: 'fallback/slic' not found.
ACPI: Writing ACPI tables at 7ff4a000.
ACPI:    * FACS
ACPI:    * DSDT
ACPI:    * FADT
ACPI: added table 1/32, length now 40
ACPI:     * SSDT
Found 1 CPU(s) with 4 core(s) each.
PSS: 2801MHz power 35000 control 0x2300 status 0x2300
PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00
PSS: 2400MHz power 28615 control 0x1800 status 0x1800
PSS: 2000MHz power 22765 control 0x1400 status 0x1400
PSS: 1600MHz power 17346 control 0x1000 status 0x1000
PSS: 1200MHz power 12373 control 0xc00 status 0xc00
PSS: 800MHz power 7830 control 0x800 status 0x800
PSS: 2801MHz power 35000 control 0x2300 status 0x2300
PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00
PSS: 2400MHz power 28615 control 0x1800 status 0x1800
PSS: 2000MHz power 22765 control 0x1400 status 0x1400
PSS: 1600MHz power 17346 control 0x1000 status 0x1000
PSS: 1200MHz power 12373 control 0xc00 status 0xc00
PSS: 800MHz power 7830 control 0x800 status 0x800
PSS: 2801MHz power 35000 control 0x2300 status 0x2300
PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00
PSS: 2400MHz power 28615 control 0x1800 status 0x1800
PSS: 2000MHz power 22765 control 0x1400 status 0x1400
PSS: 1600MHz power 17346 control 0x1000 status 0x1000
PSS: 1200MHz power 12373 control 0xc00 status 0xc00
PSS: 800MHz power 7830 control 0x800 status 0x800
PSS: 2801MHz power 35000 control 0x2300 status 0x2300
PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00
PSS: 2400MHz power 28615 control 0x1800 status 0x1800
PSS: 2000MHz power 22765 control 0x1400 status 0x1400
PSS: 1600MHz power 17346 control 0x1000 status 0x1000
PSS: 1200MHz power 12373 control 0xc00 status 0xc00
PSS: 800MHz power 7830 control 0x800 status 0x800
Generating ACPI PIRQ entries
\_SB.PCI0.LPCB.TPM: LPC TPM PNP: 0c31.0
ACPI:    * H8
H8: BDC installed
H8: WWAN detection not implemented. Assuming WWAN installed
\_SB.PCI0.RP01.WIFI:  PCI: 01:00.0
ACPI: added table 2/32, length now 44
ACPI:    * MCFG
ACPI: added table 3/32, length now 48
ACPI:    * TCPA
TCPA log created at 7ff39000
ACPI: added table 4/32, length now 52
ACPI:    * MADT
ACPI: added table 5/32, length now 56
current = 7ff4f500
ACPI:     * DMAR
ACPI: added table 6/32, length now 60
current = 7ff4f5b0
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'vbt.bin'
CBFS: Found @ offset 39400 size 558
Found a VBT of 3985 bytes after decompression
GMA: Found VBT in CBFS
GMA: Found valid VBT in CBFS
ACPI:    * HPET
ACPI: added table 7/32, length now 64
ACPI: done.
ACPI tables: 30192 bytes.
smbios_write_tables: 7ff38000
Create SMBIOS type 17
PCI: 01:00.0 (unknown)
SMBIOS tables: 670 bytes.
Writing table forward entry at 0x00000500
Wrote coreboot table at: 00000500, 0x10 bytes, checksum 9fe7
Writing coreboot table at 0x7ff6e000
 0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
 1. 0000000000001000-000000000009ffff: RAM
 2. 00000000000a0000-00000000000fffff: RESERVED
 3. 0000000000100000-000000001fffffff: RAM
 4. 0000000020000000-00000000201fffff: RESERVED
 5. 0000000020200000-000000003fffffff: RAM
 6. 0000000040000000-00000000401fffff: RESERVED
 7. 0000000040200000-000000007ff37fff: RAM
 8. 000000007ff38000-000000007ff86fff: CONFIGURATION TABLES
 9. 000000007ff87000-000000007ffcefff: RAMSTAGE
10. 000000007ffcf000-000000007fffffff: CONFIGURATION TABLES
11. 0000000080000000-00000000829fffff: RESERVED
12. 00000000f0000000-00000000f3ffffff: RESERVED
13. 00000000fed40000-00000000fed44fff: RESERVED
14. 00000000fed90000-00000000fed91fff: RESERVED
15. 0000000100000000-000000027b5fffff: RAM
Manufacturer: c2
SF: Detected MX25L6405D with sector size 0x1000, total 0x800000
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
Wrote coreboot table at: 7ff6e000, 0x38c bytes, checksum b52
coreboot table: 932 bytes.
IMD ROOT    0. 7ffff000 00001000
IMD SMALL   1. 7fffe000 00001000
CONSOLE     2. 7ffde000 00020000
TIME STAMP  3. 7ffdd000 00000910
ROMSTG STCK 4. 7ffd8000 00005000
AFTER CAR   5. 7ffcf000 00009000
RAMSTAGE    6. 7ff86000 00049000
SMM BACKUP  7. 7ff76000 00010000
COREBOOT    8. 7ff6e000 00008000
ACPI        9. 7ff4a000 00024000
ACPI GNVS  10. 7ff49000 00001000
TCPA TCGLOG11. 7ff39000 00010000
SMBIOS     12. 7ff38000 00000800
IMD small region:
  IMD ROOT    0. 7fffec00 00000400
  MEM INFO    1. 7fffea40 000001a9
  ROMSTAGE    2. 7fffea20 00000004
  COREBOOTFWD 3. 7fffe9e0 00000028
BS: BS_WRITE_TABLES times (us): entry 0 run 25502 exit 0
CBFS: 'Master Header Locator' located CBFS at [720000:800000)
CBFS: Locating 'fallback/payload'
CBFS: Found @ offset 41400 size 106fd
Checking segment from ROM address 0xfff61438
Payload being loaded at below 1MiB without region being marked as RAM usable.
Checking segment from ROM address 0xfff61454
Loading segment from ROM address 0xfff61438
  code (compression=1)
  New segment dstaddr 0x000e0d20 memsize 0x1f2e0 srcaddr 0xfff61470 filesize 0x106c5
Loading Segment: addr: 0x000e0d20 memsz: 0x000000000001f2e0 filesz: 0x00000000000106c5
using LZMA
Loading segment from ROM address 0xfff61454
  Entry Point 0x000fd274
BS: BS_PAYLOAD_LOAD times (us): entry 1 run 23347 exit 0
PCH: watchdog disabled
Jumping to boot code at 000fd274(7ff6e000)
SeaBIOS (version rel-1.12.0-0-ga698c89)
BUILD: gcc: (coreboot toolchain v1.53 August 16th, 2018) 8.1.0 binutils: (GNU Binutils) 2.30
Found coreboot cbmem console @ 7ffde000
Found mainboard LENOVO ThinkPad T420
Relocating init from 0x000e2380 to 0x7feeb520 (size 51680)
Found CBFS header at 0xfff20038
multiboot: eax=7ffb9f80, ebx=7ffb9f34
Found 16 PCI devices (max PCI bus is 03)
Copying SMBIOS entry point from 0x7ff38000 to 0x000f67a0
Copying ACPI RSDP from 0x7ff4a000 to 0x000f6770
Using pmtimer, ioport 0x508
Scan for VGA option rom
Running option rom at c000:0003
pmm call arg1=0
Turning on vga text mode console
SeaBIOS (version rel-1.12.0-0-ga698c89)
Machine UUID f7c29201-520c-11cb-ae0a-853cb0d59b9b
EHCI init on dev 00:1a.0 (regs=0xe162f020)
EHCI init on dev 00:1d.0 (regs=0xe1630020)
AHCI controller at 00:1f.2, iobase 0xe162e000, irq 10
Searching bootorder for: /pci@i0cf8/pci-bridge@1c,3/*@0
Found 0 lpt ports
Found 0 serial ports
Discarding ps2 data f0 (status=11)
Searching bootorder for: /pci@i0cf8/*@1f,2/drive@0/disk@0
AHCI/0: Set transfer mode to UDMA-6
AHCI/0: registering: "AHCI/0: ST320LT007-9ZV142 ATA-8 Hard-Disk (298 GiBytes)"
Searching bootorder for: /pci@i0cf8/*@1f,2/drive@1/disk@0
AHCI/1: Set transfer mode to UDMA-6
AHCI/1: registering: "AHCI/1: ST9500325ASG ATA-8 Hard-Disk (465 GiBytes)"
Initialized USB HUB (0 ports used)
Initialized USB HUB (0 ports used)
PS2 keyboard initialized
All threads complete.
Scan for option roms

Press ESC for boot menu.

Searching bootorder for: HALT
drive 0x000f6700: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=625142448
drive 0x000f66b0: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=976773168
Space available for UMB: c7000-ed800, f5fc0-f66b0
Returned 253952 bytes of ZoneHigh
e820 map has 13 items:
  0: 0000000000000000 - 000000000009fc00 = 1 RAM
  1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
  2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
  3: 0000000000100000 - 0000000020000000 = 1 RAM
  4: 0000000020000000 - 0000000020200000 = 2 RESERVED
  5: 0000000020200000 - 0000000040000000 = 1 RAM
  6: 0000000040000000 - 0000000040200000 = 2 RESERVED
  7: 0000000040200000 - 000000007ff36000 = 1 RAM
  8: 000000007ff36000 - 0000000082a00000 = 2 RESERVED
  9: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
  10: 00000000fed40000 - 00000000fed45000 = 2 RESERVED
  11: 00000000fed90000 - 00000000fed92000 = 2 RESERVED
  12: 0000000100000000 - 000000027b600000 = 1 RAM
enter handle_19:
  NULL
Booting from Hard Disk...
Booting from 0000:7c00