| [ 0.000000] Initializing cgroup subsys cpuset |
| [ 0.000000] Initializing cgroup subsys cpu |
| [ 0.000000] Initializing cgroup subsys cpuacct |
| [ 0.000000] Linux version 4.4.14-smp (root@hive) (gcc version 5.3.0 (GCC) ) #2 SMP Fri Jun 24 14:44:24 CDT 2016 |
| [ 0.000000] x86/fpu: Legacy x87 FPU detected. |
| [ 0.000000] x86/fpu: Using 'lazy' FPU context switches. |
| [ 0.000000] e820: BIOS-provided physical RAM map: |
| [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable |
| [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved |
| [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved |
| [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001ffe3fff] usable |
| [ 0.000000] BIOS-e820: [mem 0x000000001ffe4000-0x000000001fffffff] reserved |
| [ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved |
| [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU! |
| [ 0.000000] SMBIOS 2.7 present. |
| [ 0.000000] DMI: ASUS P3B-F/P3B-F, BIOS 4.6-1437-ga097fb8fff 09/13/2017 |
| [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved |
| [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable |
| [ 0.000000] e820: last_pfn = 0x1ffe4 max_arch_pfn = 0x1000000 |
| [ 0.000000] MTRR default type: uncachable |
| [ 0.000000] MTRR fixed ranges enabled: |
| [ 0.000000] 00000-9FFFF write-back |
| [ 0.000000] A0000-BFFFF uncachable |
| [ 0.000000] C0000-FFFFF write-back |
| [ 0.000000] MTRR variable ranges enabled: |
| [ 0.000000] 0 base 000000000 mask FE0000000 write-back |
| [ 0.000000] 1 base 0F0000000 mask FFF800000 write-combining |
| [ 0.000000] 2 disabled |
| [ 0.000000] 3 disabled |
| [ 0.000000] 4 disabled |
| [ 0.000000] 5 disabled |
| [ 0.000000] 6 disabled |
| [ 0.000000] 7 disabled |
| [ 0.000000] x86/PAT: PAT not supported by CPU. |
| [ 0.000000] initial memory mapped: [mem 0x00000000-0x027fffff] |
| [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384 |
| [ 0.000000] BRK [0x0224c000, 0x0224cfff] PGTABLE |
| [ 0.000000] BRK [0x0224d000, 0x0224efff] PGTABLE |
| [ 0.000000] BRK [0x0224f000, 0x0224ffff] PGTABLE |
| [ 0.000000] BRK [0x02250000, 0x02250fff] PGTABLE |
| [ 0.000000] ACPI: Early table checksum verification disabled |
| [ 0.000000] ACPI BIOS Error (bug): A valid RSDP was not found (20150930/tbxfroot-243) |
| [ 0.000000] No NUMA configuration found |
| [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000001ffe3fff] |
| [ 0.000000] NODE_DATA(0) allocated [mem 0x1ffe2000-0x1ffe3fff] |
| [ 0.000000] 0MB HIGHMEM available. |
| [ 0.000000] 511MB LOWMEM available. |
| [ 0.000000] max_low_pfn = 1ffe4, highstart_pfn = 1ffe4 |
| [ 0.000000] Low memory ends at vaddr dffe4000 |
| [ 0.000000] High memory starts at vaddr dffe4000 |
| [ 0.000000] mapped low ram: 0 - 1ffe4000 |
| [ 0.000000] low ram: 0 - 1ffe4000 |
| [ 0.000000] Node: 0, start_pfn: 1, end_pfn: 9f |
| [ 0.000000] Setting physnode_map array to node 0 for pfns: |
| [ 0.000000] 0 |
| [ 0.000000] Node: 0, start_pfn: 100, end_pfn: 1ffe4 |
| [ 0.000000] Setting physnode_map array to node 0 for pfns: |
| [ 0.000000] 0 4000 8000 c000 10000 14000 18000 1c000 |
| [ 0.000000] Zone ranges: |
| [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] |
| [ 0.000000] Normal [mem 0x0000000001000000-0x000000001ffe3fff] |
| [ 0.000000] HighMem empty |
| [ 0.000000] Movable zone start for each node |
| [ 0.000000] Early memory node ranges |
| [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] |
| [ 0.000000] node 0: [mem 0x0000000000100000-0x000000001ffe3fff] |
| [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000001ffe3fff] |
| [ 0.000000] On node 0 totalpages: 130946 |
| [ 0.000000] free_area_init_node: node 0, pgdat dffe2000, node_mem_map dfae2028 |
| [ 0.000000] DMA zone: 40 pages used for memmap |
| [ 0.000000] DMA zone: 0 pages reserved |
| [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 |
| [ 0.000000] Normal zone: 1240 pages used for memmap |
| [ 0.000000] Normal zone: 126948 pages, LIFO batch:31 |
| [ 0.000000] Using APIC driver default |
| [ 0.000000] SFI: Simple Firmware Interface v0.81 http://simplefirmware.org |
| [ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs |
| [ 0.000000] Found and enabled local APIC! |
| [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] |
| [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] |
| [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] |
| [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] |
| [ 0.000000] e820: [mem 0x20000000-0xff7fffff] available for PCI devices |
| [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns |
| [ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 |
| [ 0.000000] PERCPU: Embedded 18 pages/cpu @dfacc000 s42636 r0 d31092 u73728 |
| [ 0.000000] pcpu-alloc: s42636 r0 d31092 u73728 alloc=18*4096 |
| [ 0.000000] pcpu-alloc: [0] 0 |
| [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129666 |
| [ 0.000000] Policy zone: Normal |
| [ 0.000000] Kernel command line: auto BOOT_IMAGE=Linux ro root=801 vt.default_utf8=0 |
| [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) |
| [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) |
| [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) |
| [ 0.000000] Initializing CPU#0 |
| [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) |
| [ 0.000000] Memory: 499348K/523784K available (12341K kernel code, 927K rwdata, 3824K rodata, 832K init, 676K bss, 24436K reserved, 0K cma-reserved, 0K highmem) |
| [ 0.000000] virtual kernel memory layout: |
| fixmap : 0xffd37000 - 0xfffff000 (2848 kB) |
| pkmap : 0xffa00000 - 0xffc00000 (2048 kB) |
| vmalloc : 0xe07e4000 - 0xff9fe000 ( 498 MB) |
| lowmem : 0xc0000000 - 0xdffe4000 ( 511 MB) |
| .init : 0xc20b4000 - 0xc2184000 ( 832 kB) |
| .data : 0xc1c0d8e3 - 0xc20b2d80 (4757 kB) |
| .text : 0xc1000000 - 0xc1c0d8e3 (12342 kB) |
| [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. |
| [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 |
| [ 0.000000] Hierarchical RCU implementation. |
| [ 0.000000] Build-time adjustment of leaf fanout to 32. |
| [ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=1. |
| [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 |
| [ 0.000000] NR_IRQS:2304 nr_irqs:32 16 |
| [ 0.000000] CPU 0 irqstacks, hard=df424000 soft=df426000 |
| [ 0.000000] Console: colour VGA+ 80x25 |
| [ 0.000000] console [tty0] enabled |
| [ 0.000000] tsc: Fast TSC calibration using PIT |
| [ 0.000000] tsc: Detected 935.438 MHz processor |
| [ 0.002014] Calibrating delay loop (skipped), value calculated using timer frequency.. 1870.87 BogoMIPS (lpj=935438) |
| [ 0.003166] pid_max: default: 32768 minimum: 301 |
| [ 0.003439] Security Framework initialized |
| [ 0.003666] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) |
| [ 0.003834] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) |
| [ 0.005436] Initializing cgroup subsys io |
| [ 0.005660] Initializing cgroup subsys memory |
| [ 0.005883] Initializing cgroup subsys devices |
| [ 0.006046] Initializing cgroup subsys freezer |
| [ 0.006220] Initializing cgroup subsys net_cls |
| [ 0.006391] Initializing cgroup subsys perf_event |
| [ 0.006564] Initializing cgroup subsys net_prio |
| [ 0.006735] Initializing cgroup subsys pids |
| [ 0.007171] mce: CPU supports 5 MCE banks |
| [ 0.007408] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 2 |
| [ 0.007574] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8, 1GB 0 |
| [ 0.038206] Freeing SMP alternatives memory: 40K (c2184000 - c218e000) |
| [ 0.038404] ftrace: allocating 41039 entries in 81 pages |
| [ 0.077413] smpboot: weird, boot CPU (#0) not listed by the BIOS |
| [ 0.077616] smpboot: SMP motherboard not detected |
| [ 0.077770] smpboot: SMP disabled |
| [ 0.078052] Enabling APIC mode: Flat. Using 0 I/O APICs |
| [ 0.180219] Performance Events: p6 PMU driver. |
| [ 0.180421] ... version: 0 |
| [ 0.180566] ... bit width: 32 |
| [ 0.180717] ... generic registers: 2 |
| [ 0.180867] ... value mask: 00000000ffffffff |
| [ 0.181000] ... max period: 000000007fffffff |
| [ 0.181013] ... fixed-purpose events: 0 |
| [ 0.181168] ... event mask: 0000000000000003 |
| [ 0.182823] x86: Booted up 1 node, 1 CPUs |
| [ 0.183026] smpboot: Total of 1 processors activated (1870.87 BogoMIPS) |
| [ 0.184047] devtmpfs: initialized |
| [ 0.186294] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns |
| [ 0.187093] xor: measuring software checksum speed |
| [ 0.197007] pIII_sse : 1872.000 MB/sec |
| [ 0.207009] prefetch64-sse: 1988.000 MB/sec |
| [ 0.207165] xor: using function: prefetch64-sse (1988.000 MB/sec) |
| [ 0.207374] atomic64_test: passed for i586+ platform with CX8 and with SSE |
| [ 0.207515] pinctrl core: initialized pinctrl subsystem |
| [ 0.208862] NET: Registered protocol family 16 |
| [ 0.210064] cpuidle: using governor ladder |
| [ 0.210234] cpuidle: using governor menu |
| [ 0.212516] PCI: PCI BIOS revision 2.10 entry at 0xfd4d9, last bus=1 |
| [ 0.212692] PCI: Using configuration type 1 for base access |
| [ 0.251053] raid6: mmxx1 gen() 882 MB/s |
| [ 0.268036] raid6: mmxx2 gen() 1050 MB/s |
| [ 0.285015] raid6: sse1x1 gen() 796 MB/s |
| [ 0.302027] raid6: sse1x2 gen() 1042 MB/s |
| [ 0.319114] raid6: int32x1 gen() 273 MB/s |
| [ 0.336120] raid6: int32x1 xor() 140 MB/s |
| [ 0.353013] raid6: int32x2 gen() 355 MB/s |
| [ 0.370074] raid6: int32x2 xor() 195 MB/s |
| [ 0.387102] raid6: int32x4 gen() 320 MB/s |
| [ 0.404158] raid6: int32x4 xor() 199 MB/s |
| [ 0.421073] raid6: int32x8 gen() 281 MB/s |
| [ 0.438063] raid6: int32x8 xor() 175 MB/s |
| [ 0.438218] raid6: using algorithm mmxx2 gen() 1050 MB/s |
| [ 0.438374] raid6: using intx1 recovery algorithm |
| [ 0.438802] ACPI: Interpreter disabled. |
| [ 0.439270] vgaarb: loaded |
| [ 0.440108] SCSI subsystem initialized |
| [ 0.440564] libata version 3.00 loaded. |
| [ 0.440721] usbcore: registered new interface driver usbfs |
| [ 0.440964] usbcore: registered new interface driver hub |
| [ 0.441082] usbcore: registered new device driver usb |
| [ 0.442049] PCI: Probing PCI hardware |
| [ 0.442220] PCI: root bus 00: using default resources |
| [ 0.442227] PCI: Probing PCI hardware (bus 00) |
| [ 0.442366] PCI host bridge to bus 0000:00 |
| [ 0.442532] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] |
| [ 0.442694] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff] |
| [ 0.442859] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] |
| [ 0.443052] pci 0000:00:00.0: [8086:7190] type 00 class 0x060000 |
| [ 0.443092] pci 0000:00:00.0: reg 0x10: [mem 0xe0000000-0xefffffff pref] |
| [ 0.443342] pci 0000:00:01.0: [8086:7191] type 01 class 0x060400 |
| [ 0.443509] pci 0000:00:04.0: [8086:7110] type 00 class 0x060100 |
| [ 0.443739] pci 0000:00:04.1: [8086:7111] type 00 class 0x010180 |
| [ 0.443803] pci 0000:00:04.1: reg 0x20: [io 0x1420-0x142f] |
| [ 0.443836] pci 0000:00:04.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] |
| [ 0.444014] pci 0000:00:04.1: legacy IDE quirk: reg 0x14: [io 0x03f6] |
| [ 0.444174] pci 0000:00:04.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] |
| [ 0.444337] pci 0000:00:04.1: legacy IDE quirk: reg 0x1c: [io 0x0376] |
| [ 0.444668] pci 0000:00:04.2: [8086:7112] type 00 class 0x0c0300 |
| [ 0.444735] pci 0000:00:04.2: reg 0x20: [io 0x1400-0x141f] |
| [ 0.445084] pci 0000:00:04.3: [8086:7113] type 00 class 0x068000 |
| [ 0.445098] * Found PM-Timer Bug on the chipset. Due to workarounds for a bug, |
| * this clock source is slow. Consider trying other clock sources |
| [ 0.445582] pci 0000:00:04.3: quirk: [io 0xe400-0xe43f] claimed by PIIX4 ACPI |
| [ 0.445853] pci 0000:00:04.3: quirk: [io 0x0f00-0x0f0f] claimed by PIIX4 SMB |
| [ 0.446183] pci 0000:00:0b.0: [1186:1300] type 00 class 0x020000 |
| [ 0.446219] pci 0000:00:0b.0: reg 0x10: [io 0x1000-0x10ff] |
| [ 0.446238] pci 0000:00:0b.0: reg 0x14: [mem 0xf1014000-0xf10140ff] |
| [ 0.446316] pci 0000:00:0b.0: supports D1 D2 |
| [ 0.446325] pci 0000:00:0b.0: PME# supported from D1 D2 D3hot D3cold |
| [ 0.446490] pci 0000:00:0c.0: [102b:051a] type 00 class 0x030000 |
| [ 0.446516] pci 0000:00:0c.0: reg 0x10: [mem 0xf1010000-0xf1013fff] |
| [ 0.446535] pci 0000:00:0c.0: reg 0x14: [mem 0xf0000000-0xf07fffff pref] |
| [ 0.446552] pci 0000:00:0c.0: reg 0x18: [mem 0xf0800000-0xf0ffffff] |
| [ 0.446596] pci 0000:00:0c.0: reg 0x30: [mem 0xf1000000-0xf100ffff pref] |
| [ 0.446720] vgaarb: setting as boot device: PCI:0000:00:0c.0 |
| [ 0.446884] vgaarb: device added: PCI:0000:00:0c.0,decodes=io+mem,owns=io+mem,locks=none |
| [ 0.447189] pci 0000:00:01.0: PCI bridge to [bus 01] |
| [ 0.447372] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 |
| [ 0.447482] pci 0000:00:04.0: PIIX/ICH IRQ router [8086:7110] |
| [ 0.447674] PCI: pci_cache_line_size set to 32 bytes |
| [ 0.447728] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] |
| [ 0.447739] e820: reserve RAM buffer [mem 0x1ffe4000-0x1fffffff] |
| [ 0.449248] clocksource: Switched to clocksource refined-jiffies |
| [ 0.519082] pnp: PnP ACPI: disabled |
| [ 0.526877] pci 0000:00:01.0: PCI bridge to [bus 01] |
| [ 0.527049] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] |
| [ 0.527059] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff] |
| [ 0.527254] NET: Registered protocol family 2 |
| [ 0.528630] TCP established hash table entries: 4096 (order: 2, 16384 bytes) |
| [ 0.528911] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) |
| [ 0.529193] TCP: Hash tables configured (established 4096 bind 4096) |
| [ 0.529599] UDP hash table entries: 256 (order: 1, 8192 bytes) |
| [ 0.529805] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) |
| [ 0.530383] NET: Registered protocol family 1 |
| [ 0.531269] RPC: Registered named UNIX socket transport module. |
| [ 0.532006] RPC: Registered udp transport module. |
| [ 0.532997] RPC: Registered tcp transport module. |
| [ 0.533149] RPC: Registered tcp NFSv4.1 backchannel transport module. |
| [ 0.533417] pci 0000:00:00.0: Limiting direct PCI/PCI transfers |
| [ 0.533641] PCI: setting IRQ 5 as level-triggered |
| [ 0.533653] pci 0000:00:04.2: assigned PCI INT D -> IRQ 5 |
| [ 0.533873] pci 0000:00:0c.0: Video device with shadowed ROM |
| [ 0.533882] PCI: CLS 0 bytes, default 32 |
| [ 0.534972] platform rtc_cmos: registered platform RTC device (no PNP device found) |
| [ 0.537193] futex hash table entries: 256 (order: 2, 16384 bytes) |
| [ 0.537489] audit: initializing netlink subsys (disabled) |
| [ 0.537728] audit: type=2000 audit(1804441515.536:1): initialized |
| [ 0.538519] Initialise system trusted keyring |
| [ 0.547478] VFS: Disk quotas dquot_6.6.0 |
| [ 0.547883] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) |
| [ 0.550809] NFS: Registering the id_resolver key type |
| [ 0.551068] Key type id_resolver registered |
| [ 0.551221] Key type id_legacy registered |
| [ 0.551394] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). |
| [ 0.552473] ntfs: driver 2.1.32 [Flags: R/W]. |
| [ 0.552898] romfs: ROMFS MTD (C) 2007 Red Hat, Inc. |
| [ 0.553403] JFS: nTxBlock = 3901, nTxLock = 31211 |
| [ 0.567393] SGI XFS with ACLs, security attributes, no debug enabled |
| [ 0.569855] ocfs2: Registered cluster interface o2cb |
| [ 0.570335] OCFS2 User DLM kernel interface loaded |
| [ 0.579400] async_tx: api initialized (async) |
| [ 0.579783] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) |
| [ 0.580317] io scheduler noop registered |
| [ 0.580486] io scheduler deadline registered |
| [ 0.580714] io scheduler cfq registered (default) |
| [ 0.581524] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 |
| [ 0.581713] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 |
| [ 0.581960] intel_idle: does not run on family 6 model 11 |
| [ 0.582099] isapnp: Scanning for PnP cards... |
| [ 0.939473] isapnp: No Plug & Play device found |
| [ 0.945426] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled |
| [ 1.189969] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A |
| [ 1.434928] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A |
| [ 1.440552] Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?) |
| [ 1.456102] brd: module loaded |
| [ 1.456314] HP CISS Driver (v 3.6.26) |
| [ 1.458601] FDC 0 is a post-1991 82077 |
| [ 1.461649] fnic: Cisco FCoE HBA Driver, ver 1.6.0.17a |
| [ 1.462203] fnic: Successfully Initialized Trace Buffer |
| [ 1.464415] fnic: Successfully Initialized FC_CTLR Trace Buffer |
| [ 1.469751] Adaptec aacraid driver 1.2-1[41010]-ms |
| [ 1.469965] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded |
| [ 1.470521] scsi: <fdomain> Detection failed (no card) |
| [ 1.470704] sym53c416.c: Version 1.0.0-ac |
| [ 1.470926] qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options |
| [ 1.471262] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.07.00.26-k. |
| [ 1.471968] Emulex LightPulse Fibre Channel SCSI driver 11.0.0.0. |
| [ 1.472127] Copyright(c) 2004-2015 Emulex. All rights reserved. |
| [ 1.472591] Brocade BFA FC/FCOE SCSI driver - version: 3.2.23.0 |
| [ 1.494864] Failed initialization of WD-7000 SCSI card! |
| [ 1.545679] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1af7b3b2689, max_idle_ns: 881590587356 ns |
| [ 1.545886] clocksource: Switched to clocksource tsc |
| [ 1.546139] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) |
| [ 1.546585] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) |
| [ 1.546818] megasas: 06.808.16.00-rc1 |
| [ 1.547059] mpt3sas version 09.102.00.00 loaded |
| [ 1.547594] GDT-HA: Storage RAID Controller Driver. Version: 3.05 |
| [ 1.547911] 3ware Storage Controller device driver for Linux v1.26.02.003. |
| [ 1.548102] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. |
| [ 1.548377] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. |
| [ 1.548654] ipr: IBM Power RAID SCSI Device Driver version: 2.6.3 (October 17, 2015) |
| [ 1.548970] RocketRAID 3xxx/4xxx Controller driver v1.10.0 |
| [ 1.549159] stex: Promise SuperTrak EX Driver version: 4.6.0000.4 |
| [ 1.549638] st: Version 20101219, fixed bufsize 32768, s/g segs 256 |
| [ 1.550895] ata_piix 0000:00:04.1: version 2.13 |
| [ 1.552709] scsi host2: ata_piix |
| [ 1.553414] scsi host3: ata_piix |
| [ 1.553820] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1420 irq 14 |
| [ 1.553988] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1428 irq 15 |
| [ 1.558076] Fusion MPT base driver 3.04.20 |
| [ 1.558253] Copyright (c) 1999-2008 LSI Corporation |
| [ 1.558430] Fusion MPT SPI Host driver 3.04.20 |
| [ 1.558653] Fusion MPT FC Host driver 3.04.20 |
| [ 1.558927] Fusion MPT SAS Host driver 3.04.20 |
| [ 1.559194] Fusion MPT misc device (ioctl) driver 3.04.20 |
| [ 1.559613] mptctl: Registered with Fusion MPT base driver |
| [ 1.559801] mptctl: /dev/mptctl @ (major,minor=10,220) |
| [ 1.559966] Fusion MPT LAN driver 3.04.20 |
| [ 1.560451] i8042: PNP: No PS/2 controller found. Probing ports directly. |
| [ 1.563320] serio: i8042 KBD port at 0x60,0x64 irq 1 |
| [ 1.563486] serio: i8042 AUX port at 0x60,0x64 irq 12 |
| [ 1.564293] mousedev: PS/2 mouse device common for all mice |
| [ 1.565040] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 |
| [ 1.565244] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram |
| [ 1.565429] md: linear personality registered for level -1 |
| [ 1.565589] md: raid0 personality registered for level 0 |
| [ 1.565799] md: raid1 personality registered for level 1 |
| [ 1.565962] md: raid10 personality registered for level 10 |
| [ 1.566438] md: raid6 personality registered for level 6 |
| [ 1.566601] md: raid5 personality registered for level 5 |
| [ 1.566786] md: raid4 personality registered for level 4 |
| [ 1.566966] md: multipath personality registered for level -4 |
| [ 1.567366] device-mapper: uevent: version 1.0.3 |
| [ 1.567950] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com |
| [ 1.568977] input: Speakup as /devices/virtual/input/input1 |
| [ 1.569476] initialized device: /dev/synth, node (MAJOR 10, MINOR 25) |
| [ 1.569819] speakup 3.1.6: initialized |
| [ 1.569984] synth name on entry is: (null) |
| [ 1.570807] Initializing XFRM netlink socket |
| [ 1.571001] NET: Registered protocol family 17 |
| [ 1.571310] 9pnet: Installing 9P2000 support |
| [ 1.571597] Key type dns_resolver registered |
| [ 1.572789] microcode: CPU0 sig=0x6b1, pf=0x10, revision=0x1c |
| [ 1.573170] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba |
| [ 1.573511] Using IPI No-Shortcut mode |
| [ 1.574317] registered taskstats version 1 |
| [ 1.574507] Loading compiled-in X.509 certificates |
| [ 1.576950] Btrfs loaded |
| [ 1.578550] Key type encrypted registered |
| [ 1.587992] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 |
| [ 1.721158] ata1.00: ATA-7: Maxtor 6E040L0, NAR61590, max UDMA/133 |
| [ 1.721356] ata1.00: 80293248 sectors, multi 0: LBA |
| [ 1.724961] ata1.00: configured for UDMA/33 |
| [ 1.725875] scsi 2:0:0:0: Direct-Access ATA Maxtor 6E040L0 1590 PQ: 0 ANSI: 5 |
| [ 1.726975] sd 2:0:0:0: [sda] 80293248 512-byte logical blocks: (41.1 GB/38.3 GiB) |
| [ 1.727444] sd 2:0:0:0: [sda] Write Protect is off |
| [ 1.727613] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 |
| [ 1.727722] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA |
| [ 1.761112] sda: sda1 sda2 < sda5 > |
| [ 1.762899] sd 2:0:0:0: [sda] Attached SCSI disk |
| [ 1.763452] md: Waiting for all devices to be available before autodetect |
| [ 1.763670] md: If you don't use raid, use raid=noautodetect |
| [ 1.764828] md: Autodetecting RAID arrays. |
| [ 1.765010] md: Scanned 0 and added 0 devices. |
| [ 1.765168] md: autorun ... |
| [ 1.765322] md: ... autorun DONE. |
| [ 1.796683] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities |
| [ 1.799116] EXT4-fs (sda1): INFO: recovery required on readonly filesystem |
| [ 1.799301] EXT4-fs (sda1): write access will be enabled during recovery |
| [ 2.622816] EXT4-fs (sda1): recovery complete |
| [ 2.646982] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) |
| [ 2.647349] VFS: Mounted root (ext4 filesystem) readonly on device 8:1. |
| [ 2.691124] devtmpfs: mounted |
| [ 2.699035] Freeing unused kernel memory: 832K (c20b4000 - c2184000) |
| [ 2.699837] Write protecting the kernel text: 12344k |
| [ 2.700338] Write protecting the kernel read-only data: 3828k |
| [ 3.017128] random: nonblocking pool is initialized |
| [ 3.974219] loop: module loaded |
| [ 6.498354] udevd[510]: starting eudev-3.1.5 |
| [ 7.367644] piix4_smbus 0000:00:04.3: SMBus Host Controller at 0xf00, revision 0 |
| [ 7.565519] 8139too: 8139too Fast Ethernet driver 0.9.28 |
| [ 7.565888] PCI: setting IRQ 10 as level-triggered |
| [ 7.565906] 8139too 0000:00:0b.0: assigned PCI INT A -> IRQ 10 |
| [ 7.566984] 8139too 0000:00:0b.0 eth0: RealTek RTL8139 at 0x00011000, 00:40:05:3a:31:94, IRQ 10 |
| [ 7.611499] Linux agpgart interface v0.103 |
| [ 7.795622] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver |
| [ 7.805884] ehci-pci: EHCI PCI platform driver |
| [ 7.810517] uhci_hcd: USB Universal Host Controller Interface driver |
| [ 7.810875] uhci_hcd 0000:00:04.2: found PCI INT D -> IRQ 5 |
| [ 7.811137] uhci_hcd 0000:00:04.2: UHCI Host Controller |
| [ 7.811631] uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 |
| [ 7.811982] uhci_hcd 0000:00:04.2: irq 5, io base 0x00001400 |
| [ 7.817297] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 |
| [ 7.817493] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 |
| [ 7.817773] usb usb1: Product: UHCI Host Controller |
| [ 7.817935] usb usb1: Manufacturer: Linux 4.4.14-smp uhci_hcd |
| [ 7.818119] usb usb1: SerialNumber: 0000:00:04.2 |
| [ 7.820255] hub 1-0:1.0: USB hub found |
| [ 7.821111] hub 1-0:1.0: 2 ports detected |
| [ 7.867266] agpgart-intel 0000:00:00.0: Intel 440BX Chipset |
| [ 7.925589] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000 |
| [ 8.037148] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 |
| [ 9.686867] 8139too 0000:00:0b.0 eth126: renamed from eth0 |
| [ 9.687874] 8139too 0000:00:0b.0 eth1: renamed from eth126 |
| [ 10.045171] Adding 522236k swap on /dev/sda5. Priority:-1 extents:1 across:522236k |
| [ 10.182047] fuse init (API version 7.23) |
| [ 42.601379] EXT4-fs (sda1): re-mounted. Opts: (null) |
| [ 52.466050] 8139too 0000:00:0b.0 eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 |
| [ 56.765364] NET: Registered protocol family 10 |