| *** Pre-CBMEM romstage console overflowed, log truncated! *** |
| 66 MHz |
| Selected CAS latency : 9T |
| PLL busy... done in 40 us |
| MCU frequency is set at : 666 MHz |
| Done dimm mapping |
| Update PCI-E configuration space: |
| PCI(0, 0, 0)[a0] = 0 |
| PCI(0, 0, 0)[a4] = 2 |
| PCI(0, 0, 0)[bc] = c2a00000 |
| PCI(0, 0, 0)[a8] = 3d600000 |
| PCI(0, 0, 0)[ac] = 2 |
| PCI(0, 0, 0)[b8] = c0000000 |
| PCI(0, 0, 0)[b0] = c0a00000 |
| PCI(0, 0, 0)[b4] = c0800000 |
| Done memory map |
| Done io registers |
| t123: 1912, 9120, 500 |
| ME: FW Partition Table : OK |
| ME: Bringup Loader Failure : NO |
| ME: Firmware Init Complete : NO |
| ME: Manufacturing Mode : YES |
| ME: Boot Options Present : NO |
| ME: Update In Progress : NO |
| ME: Current Working State : Initializing |
| ME: Current Operation State : Bring up |
| ME: Current Operation Mode : Debug or Disabled by AltDisableBit |
| ME: Error Code : No Error |
| ME: Progress Phase : BUP Phase |
| ME: Power Management Event : Clean Moff->Mx wake |
| ME: Progress Phase State : Check to see if straps say ME DISABLED |
| ME: Wrong mode : 2 |
| ME: FWS2: 0x100a0000 |
| ME: Bist in progress: 0x0 |
| ME: ICC Status : 0x0 |
| ME: Invoke MEBx : 0x0 |
| ME: CPU replaced : 0x0 |
| ME: MBP ready : 0x0 |
| ME: MFS failure : 0x0 |
| ME: Warm reset req : 0x0 |
| ME: CPU repl valid : 0x0 |
| ME: (Reserved) : 0x0 |
| ME: FW update req : 0x0 |
| ME: (Reserved) : 0x0 |
| ME: Current state : 0xa |
| ME: Current PM event: 0x0 |
| ME: Progress code : 0x1 |
| Waited long enough, or CPU was not replaced, continue... |
| PASSED! Tell ME that DRAM is ready |
| ME: ME is reporting as disabled, so not waiting for a response. |
| ME: FWS2: 0x100a0000 |
| ME: Bist in progress: 0x0 |
| ME: ICC Status : 0x0 |
| ME: Invoke MEBx : 0x0 |
| ME: CPU replaced : 0x0 |
| ME: MBP ready : 0x0 |
| ME: MFS failure : 0x0 |
| ME: Warm reset req : 0x0 |
| ME: CPU repl valid : 0x0 |
| ME: (Reserved) : 0x0 |
| ME: FW update req : 0x0 |
| ME: (Reserved) : 0x0 |
| ME: Current state : 0xa |
| ME: Current PM event: 0x0 |
| ME: Progress code : 0x1 |
| ME: Requested BIOS Action: No DID Ack received |
| ME: FW Partition Table : OK |
| ME: Bringup Loader Failure : NO |
| ME: Firmware Init Complete : NO |
| ME: Manufacturing Mode : YES |
| ME: Boot Options Present : NO |
| ME: Update In Progress : NO |
| ME: Current Working State : Initializing |
| ME: Current Operation State : Bring up |
| ME: Current Operation Mode : Debug or Disabled by AltDisableBit |
| ME: Error Code : No Error |
| ME: Progress Phase : BUP Phase |
| ME: Power Management Event : Clean Moff->Mx wake |
| ME: Progress Phase State : Check to see if straps say ME DISABLED |
| memcfg DDR3 ref clock 133 MHz |
| memcfg DDR3 clock 1330 MHz |
| memcfg channel assignment: A: 1, B 0, C 2 |
| memcfg channel[0] config (00000000): |
| ECC inactive |
| enhanced interleave mode off |
| rank interleave off |
| DIMMA 0 MB width x8 single rank, selected |
| DIMMB 0 MB width x8 single rank |
| memcfg channel[1] config (00620020): |
| ECC inactive |
| enhanced interleave mode on |
| rank interleave on |
| DIMMA 8192 MB width x8 dual rank, selected |
| DIMMB 0 MB width x8 single rank |
| CBMEM: |
| IMD: root @ bffff000 254 entries. |
| IMD: root @ bfffec00 62 entries. |
| External stage cache: |
| IMD: root @ c03ff000 254 entries. |
| IMD: root @ c03fec00 62 entries. |
| CBMEM entry for DIMM info: 0xbfffe9e0 |
| MTRR Range: Start=ff800000 End=0 (Size 800000) |
| MTRR Range: Start=0 End=1000000 (Size 1000000) |
| MTRR Range: Start=bf800000 End=c0000000 (Size 800000) |
| MTRR Range: Start=c0000000 End=c0800000 (Size 800000) |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'fallback/postcar' |
| CBFS: Found @ offset 37fc0 size 4878 |
| Decompressing stage fallback/postcar @ 0xbffcefc0 (35352 bytes) |
| Loading module at bffcf000 with entry bffcf000. filesize: 0x45d0 memsize: 0x89d8 |
| Processing 147 relocs. Offset value of 0xbdfcf000 |
| |
| |
| coreboot-4.9-1860-g2761847f90 Sun Jun 2 04:11:29 UTC 2019 postcar starting (log level: 7)... |
| usbdebug: Failed hardware init |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'fallback/ramstage' |
| CBFS: Found @ offset 1af00 size 1bd34 |
| Decompressing stage fallback/ramstage @ 0xbff7efc0 (323064 bytes) |
| Loading module at bff7f000 with entry bff7f000. filesize: 0x39bd0 memsize: 0x4edb8 |
| Processing 4028 relocs. Offset value of 0xbf17f000 |
| |
| |
| coreboot-4.9-1860-g2761847f90 Sun Jun 2 04:11:29 UTC 2019 ramstage starting (log level: 7)... |
| usbdebug: Failed hardware init |
| Normal boot. |
| BS: BS_PRE_DEVICE times (us): entry 0 run 2 exit 0 |
| BS: BS_DEV_INIT_CHIPS times (us): entry 0 run 3 exit 0 |
| Enumerating buses... |
| CPU_CLUSTER: 0 enabled |
| DOMAIN: 0000 enabled |
| PCI: pci_scan_bus for bus 00 |
| PCI: 00:00.0 [8086/0104] enabled |
| PCI: 00:01.0 [8086/0101] disabled |
| PCI: 00:02.0 [8086/0126] enabled |
| PCI: 00:04.0 [8086/0103] enabled |
| PCI: 00:16.0: Disabling device |
| PCI: 00:16.0 [8086/1c3a] disabled |
| PCI: 00:16.1: Disabling device |
| PCI: 00:16.2: Disabling device |
| PCI: 00:16.3: Disabling device |
| PCI: 00:19.0 [8086/1502] enabled |
| PCI: 00:1a.0 [8086/1c2d] enabled |
| PCI: 00:1b.0 [8086/1c20] enabled |
| PCH: PCIe Root Port coalescing is enabled |
| PCI: 00:1c.0 [8086/1c10] enabled |
| PCI: 00:1c.1 [8086/1c12] enabled |
| PCI: 00:1c.2 [8086/1c14] enabled |
| PCI: 00:1c.3 [8086/1c16] enabled |
| PCI: 00:1c.4 [8086/1c18] enabled |
| PCI: 00:1c.5: Disabling device |
| PCI: 00:1c.5 [8086/1c1a] disabled |
| PCH: Remap PCIe function 6 to 5 |
| PCI: 00:1c.6 [8086/1c1c] enabled |
| PCI: 00:1c.7: Disabling device |
| PCH: PCIe map 1c.5 -> 1c.6 |
| PCH: PCIe map 1c.6 -> 1c.5 |
| PCI: 00:1d.0 [8086/1c26] enabled |
| PCI: 00:1e.0: Disabling device |
| PCI: 00:1e.0 [8086/2448] disabled |
| PCI: 00:1f.0 [8086/1c4f] enabled |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| PCI: 00:1f.2 [8086/1c01] enabled |
| PCI: 00:1f.3 [8086/1c22] enabled |
| PCI: 00:1f.5: Disabling device |
| PCI: 00:1f.5 [8086/1c09] disabled No operations |
| PCI: 00:1f.6 [8086/1c24] enabled |
| PCI: Leftover static devices: |
| PCI: 00:16.1 |
| PCI: 00:16.2 |
| PCI: 00:16.3 |
| PCI: 00:1c.7 |
| PCI: Check your devicetree.cb. |
| PCI: pci_scan_bus for bus 01 |
| scan_bus: scanning of bus PCI: 00:1c.0 took 49 usecs |
| PCI: pci_scan_bus for bus 02 |
| PCI: 02:00.0 [168c/0034] enabled |
| Enabling Common Clock Configuration |
| ASPM: Enabled L0s and L1 |
| Failed to enable LTR for dev = PCI: 02:00.0 |
| scan_bus: scanning of bus PCI: 00:1c.1 took 225 usecs |
| PCI: pci_scan_bus for bus 03 |
| scan_bus: scanning of bus PCI: 00:1c.2 took 48 usecs |
| PCI: pci_scan_bus for bus 04 |
| scan_bus: scanning of bus PCI: 00:1c.3 took 48 usecs |
| PCI: pci_scan_bus for bus 05 |
| PCI: 05:00.0 [1180/e823] enabled |
| Enabling Common Clock Configuration |
| ASPM: Enabled L0s and L1 |
| Failed to enable LTR for dev = PCI: 05:00.0 |
| scan_bus: scanning of bus PCI: 00:1c.4 took 261 usecs |
| PCI: pci_scan_bus for bus 06 |
| PCI: 06:00.0 [1033/0194] enabled |
| Enabling Common Clock Configuration |
| ASPM: Enabled L0s and L1 |
| scan_bus: scanning of bus PCI: 00:1c.5 took 240 usecs |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| PMH7: ID 04 Revision 01 |
| PNP: 00ff.1 enabled |
| PNP: 0c31.0 enabled |
| EC Firmware ID 8DHT34WW-3.20, Version 4.01C |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| No CMOS option 'low_battery_beep'. |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| H8: BDC detection not implemented. Assuming BDC installed |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| H8: WWAN not installed |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| PNP: 00ff.2 enabled |
| scan_bus: scanning of bus PCI: 00:1f.0 took 5610 usecs |
| bus: PCI: 00:1f.3[0]->I2C: 01:54 enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:55 enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:56 enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:57 enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:5c enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:5d enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:5e enabled |
| bus: PCI: 00:1f.3[0]->I2C: 01:5f enabled |
| scan_bus: scanning of bus PCI: 00:1f.3 took 45 usecs |
| scan_bus: scanning of bus DOMAIN: 0000 took 7088 usecs |
| scan_bus: scanning of bus Root Device took 7100 usecs |
| done |
| FMAP: area RW_MRC_CACHE found @ 600000 (65536 bytes) |
| MRC: No data in cbmem for 'RW_MRC_CACHE'. |
| BS: BS_DEV_ENUMERATE times (us): entry 0 run 7145 exit 9 |
| found VGA at PCI: 00:02.0 |
| Setting up VGA for PCI: 00:02.0 |
| Setting PCI_BRIDGE_CTL_VGA for bridge DOMAIN: 0000 |
| Setting PCI_BRIDGE_CTL_VGA for bridge Root Device |
| Allocating resources... |
| Reading resources... |
| Adding PCIe enhanced config space BAR 0xf0000000-0xf4000000. |
| PCI: 00:1a.0 EHCI BAR hook registered |
| More than one caller of pci_ehci_read_resources from PCI: 00:1d.0 |
| PNP: 00ff.1 missing read_resources |
| PNP: 00ff.2 missing read_resources |
| Done reading resources. |
| skipping PNP: 00ff.2@60 fixed resource, size=0! |
| skipping PNP: 00ff.2@62 fixed resource, size=0! |
| skipping PNP: 00ff.2@64 fixed resource, size=0! |
| skipping PNP: 00ff.2@66 fixed resource, size=0! |
| Setting resources... |
| TOUUD 0x23d600000 TOLUD 0xc2a00000 TOM 0x200000000 |
| MEBASE 0x7ffff00000 |
| IGD decoded, subtracting 32M UMA and 2M GTT |
| TSEG base 0xc0000000 size 8M |
| Available memory below 4GB: 3072M |
| Available memory above 4GB: 5078M |
| PCI: 00:02.0 10 <- [0x00e1000000 - 0x00e13fffff] size 0x00400000 gran 0x16 mem64 |
| PCI: 00:02.0 18 <- [0x00d0000000 - 0x00dfffffff] size 0x10000000 gran 0x1c prefmem64 |
| PCI: 00:02.0 20 <- [0x0000003000 - 0x000000303f] size 0x00000040 gran 0x06 io |
| PCI: 00:04.0 10 <- [0x00e1720000 - 0x00e1727fff] size 0x00008000 gran 0x0f mem64 |
| PCI: 00:19.0 10 <- [0x00e1700000 - 0x00e171ffff] size 0x00020000 gran 0x11 mem |
| PCI: 00:19.0 14 <- [0x00e172c000 - 0x00e172cfff] size 0x00001000 gran 0x0c mem |
| PCI: 00:19.0 18 <- [0x0000003040 - 0x000000305f] size 0x00000020 gran 0x05 io |
| PCI: 00:1a.0 EHCI Debug Port hook triggered |
| PCI: 00:1a.0 10 <- [0x00e172f000 - 0x00e172f3ff] size 0x00000400 gran 0x0a mem |
| PCI: 00:1a.0 10 <- [0x00e172f000 - 0x00e172f3ff] size 0x00000400 gran 0x0a mem |
| PCI: 00:1a.0 EHCI Debug Port relocated |
| PCI: 00:1b.0 10 <- [0x00e1728000 - 0x00e172bfff] size 0x00004000 gran 0x0e mem64 |
| PCI: 00:1c.0 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 01 io |
| PCI: 00:1c.0 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 01 prefmem |
| PCI: 00:1c.0 20 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 01 mem |
| PCI: 00:1c.1 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 02 io |
| PCI: 00:1c.1 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 02 prefmem |
| PCI: 00:1c.1 20 <- [0x00e1400000 - 0x00e14fffff] size 0x00100000 gran 0x14 bus 02 mem |
| PCI: 02:00.0 10 <- [0x00e1400000 - 0x00e147ffff] size 0x00080000 gran 0x13 mem64 |
| PCI: 02:00.0 30 <- [0x00e1480000 - 0x00e148ffff] size 0x00010000 gran 0x10 romem |
| PCI: 00:1c.2 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 03 io |
| PCI: 00:1c.2 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 03 prefmem |
| PCI: 00:1c.2 20 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 03 mem |
| PCI: 00:1c.3 1c <- [0x0000002000 - 0x0000002fff] size 0x00001000 gran 0x0c bus 04 io |
| PCI: 00:1c.3 24 <- [0x00e0000000 - 0x00e07fffff] size 0x00800000 gran 0x14 bus 04 prefmem |
| PCI: 00:1c.3 20 <- [0x00e0800000 - 0x00e0ffffff] size 0x00800000 gran 0x14 bus 04 mem |
| NONE missing set_resources |
| PCI: 00:1c.4 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 05 io |
| PCI: 00:1c.4 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 05 prefmem |
| PCI: 00:1c.4 20 <- [0x00e1500000 - 0x00e15fffff] size 0x00100000 gran 0x14 bus 05 mem |
| PCI: 05:00.0 10 <- [0x00e1500000 - 0x00e15000ff] size 0x00000100 gran 0x08 mem |
| PCI: 00:1c.5 1c <- [0x000000ffff - 0x000000fffe] size 0x00000000 gran 0x0c bus 06 io |
| PCI: 00:1c.5 24 <- [0x00efffffff - 0x00effffffe] size 0x00000000 gran 0x14 bus 06 prefmem |
| PCI: 00:1c.5 20 <- [0x00e1600000 - 0x00e16fffff] size 0x00100000 gran 0x14 bus 06 mem |
| PCI: 06:00.0 10 <- [0x00e1600000 - 0x00e1601fff] size 0x00002000 gran 0x0d mem64 |
| PCI: 00:1d.0 10 <- [0x00e1730000 - 0x00e17303ff] size 0x00000400 gran 0x0a mem |
| PNP: 00ff.1 missing set_resources |
| PNP: 00ff.2 missing set_resources |
| PCI: 00:1f.2 10 <- [0x0000003080 - 0x0000003087] size 0x00000008 gran 0x03 io |
| PCI: 00:1f.2 14 <- [0x0000003090 - 0x0000003093] size 0x00000004 gran 0x02 io |
| PCI: 00:1f.2 18 <- [0x0000003088 - 0x000000308f] size 0x00000008 gran 0x03 io |
| PCI: 00:1f.2 1c <- [0x0000003094 - 0x0000003097] size 0x00000004 gran 0x02 io |
| PCI: 00:1f.2 20 <- [0x0000003060 - 0x000000307f] size 0x00000020 gran 0x05 io |
| PCI: 00:1f.2 24 <- [0x00e172e000 - 0x00e172e7ff] size 0x00000800 gran 0x0b mem |
| PCI: 00:1f.3 10 <- [0x00e1731000 - 0x00e17310ff] size 0x00000100 gran 0x08 mem64 |
| PCI: 00:1f.6 10 <- [0x00e172d000 - 0x00e172dfff] size 0x00001000 gran 0x0c mem64 |
| Done setting resources. |
| Done allocating resources. |
| BS: BS_DEV_RESOURCES times (us): entry 0 run 2134 exit 0 |
| Enabling resources... |
| PCI: 00:00.0 subsystem <- 17aa/21db |
| PCI: 00:00.0 cmd <- 06 |
| PCI: 00:02.0 subsystem <- 17aa/21db |
| PCI: 00:02.0 cmd <- 03 |
| PCI: 00:04.0 cmd <- 02 |
| PCI: 00:19.0 subsystem <- 17aa/21ce |
| PCI: 00:19.0 cmd <- 103 |
| PCI: 00:1a.0 subsystem <- 17aa/21db |
| PCI: 00:1a.0 cmd <- 106 |
| PCI: 00:1b.0 subsystem <- 17aa/21db |
| PCI: 00:1b.0 cmd <- 102 |
| PCI: 00:1c.0 bridge ctrl <- 0003 |
| PCI: 00:1c.0 subsystem <- 17aa/21db |
| PCI: 00:1c.0 cmd <- 100 |
| PCI: 00:1c.1 bridge ctrl <- 0003 |
| PCI: 00:1c.1 subsystem <- 17aa/21db |
| PCI: 00:1c.1 cmd <- 106 |
| PCI: 00:1c.2 bridge ctrl <- 0003 |
| PCI: 00:1c.2 subsystem <- 17aa/21db |
| PCI: 00:1c.2 cmd <- 100 |
| PCI: 00:1c.3 bridge ctrl <- 0003 |
| PCI: 00:1c.3 subsystem <- 17aa/21db |
| PCI: 00:1c.3 cmd <- 107 |
| PCI: 00:1c.4 bridge ctrl <- 0003 |
| PCI: 00:1c.4 subsystem <- 17aa/21db |
| PCI: 00:1c.4 cmd <- 106 |
| PCI: 00:1c.5 bridge ctrl <- 0003 |
| PCI: 00:1c.5 subsystem <- 17aa/21db |
| PCI: 00:1c.5 cmd <- 106 |
| PCI: 00:1d.0 subsystem <- 17aa/21db |
| PCI: 00:1d.0 cmd <- 102 |
| pch_decode_init |
| PCI: 00:1f.0 subsystem <- 8086/1c4f |
| PCI: 00:1f.0 cmd <- 107 |
| PCI: 00:1f.2 subsystem <- 17aa/21db |
| PCI: 00:1f.2 cmd <- 03 |
| PCI: 00:1f.3 subsystem <- 17aa/21db |
| PCI: 00:1f.3 cmd <- 103 |
| PCI: 00:1f.6 subsystem <- 17aa/21db |
| PCI: 00:1f.6 cmd <- 02 |
| PCI: 02:00.0 cmd <- 02 |
| PCI: 05:00.0 subsystem <- 17aa/21fa |
| PCI: 05:00.0 cmd <- 06 |
| PCI: 06:00.0 cmd <- 02 |
| done. |
| BS: BS_DEV_ENABLE times (us): entry 0 run 280 exit 0 |
| Found TPM ST33ZP24 by ST Microelectronics |
| TPM: Startup |
| TPM: command 0x99 returned 0x0 |
| TPM: Asserting physical presence |
| TPM: command 0x4000000a returned 0x0 |
| TPM: command 0x65 returned 0x0 |
| TPM: flags disable=0, deactivated=0, nvlocked=1 |
| TPM: setup succeeded |
| Initializing devices... |
| Root Device init ... |
| Root Device init finished in 2 usecs |
| CPU_CLUSTER: 0 init ... |
| MTRR: Physical address space: |
| 0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6 |
| 0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0 |
| 0x00000000000c0000 - 0x00000000c0000000 size 0xbff40000 type 6 |
| 0x00000000c0000000 - 0x00000000d0000000 size 0x10000000 type 0 |
| 0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1 |
| 0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0 |
| 0x0000000100000000 - 0x000000023d600000 size 0x13d600000 type 6 |
| MTRR: Fixed MSR 0x250 0x0606060606060606 |
| MTRR: Fixed MSR 0x258 0x0606060606060606 |
| MTRR: Fixed MSR 0x259 0x0000000000000000 |
| MTRR: Fixed MSR 0x268 0x0606060606060606 |
| MTRR: Fixed MSR 0x269 0x0606060606060606 |
| MTRR: Fixed MSR 0x26a 0x0606060606060606 |
| MTRR: Fixed MSR 0x26b 0x0606060606060606 |
| MTRR: Fixed MSR 0x26c 0x0606060606060606 |
| MTRR: Fixed MSR 0x26d 0x0606060606060606 |
| MTRR: Fixed MSR 0x26e 0x0606060606060606 |
| MTRR: Fixed MSR 0x26f 0x0606060606060606 |
| CPU physical address size: 36 bits |
| MTRR: default type WB/UC MTRR counts: 3/5. |
| MTRR: WB selected as default type. |
| MTRR: 0 base 0x00000000c0000000 mask 0x0000000ff0000000 type 0 |
| MTRR: 1 base 0x00000000d0000000 mask 0x0000000ff0000000 type 1 |
| MTRR: 2 base 0x00000000e0000000 mask 0x0000000fe0000000 type 0 |
| |
| MTRR check |
| Fixed MTRRs : Enabled |
| Variable MTRRs: Enabled |
| |
| CPU has 2 cores, 4 threads enabled. |
| Setting up SMI for CPU |
| Will perform SMM setup. |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'cpu_microcode_blob.bin' |
| CBFS: Found @ offset 14a80 size 6400 |
| microcode: sig=0x206a7 pf=0x10 revision=0x2e |
| CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz. |
| Loading module at 00030000 with entry 00030000. filesize: 0x170 memsize: 0x170 |
| Processing 16 relocs. Offset value of 0x00030000 |
| Attempting to start 3 APs |
| Waiting for 10ms after sending INIT. |
| Waiting for 1st SIPI to complete...done. |
| Waiting for 2nd SIPI to complete...AP: slot 1 apic_id 1. |
| done. |
| AP: slot 3 apic_id 2. |
| AP: slot 2 apic_id 3. |
| Loading module at 00038000 with entry 00038000. filesize: 0x1a8 memsize: 0x1a8 |
| Processing 13 relocs. Offset value of 0x00038000 |
| SMM Module: stub loaded at 00038000. Will call bff9ee34(00000000) |
| Installing SMM handler to 0xc0000000 |
| Loading module at c0010000 with entry c0010481. filesize: 0x1b90 memsize: 0x5bb8 |
| Processing 74 relocs. Offset value of 0xc0010000 |
| Loading module at c0008000 with entry c0008000. filesize: 0x1a8 memsize: 0x1a8 |
| Processing 13 relocs. Offset value of 0xc0008000 |
| SMM Module: placing jmp sequence at c0007c00 rel16 0x03fd |
| SMM Module: placing jmp sequence at c0007800 rel16 0x07fd |
| SMM Module: placing jmp sequence at c0007400 rel16 0x0bfd |
| SMM Module: stub loaded at c0008000. Will call c0010481(00000000) |
| Initializing Southbridge SMI... |
| |
| New SMBASE 0xc0000000 |
| In relocation handler: cpu 0 |
| New SMBASE=0xc0000000 IEDBASE=0xc0400000 |
| Writing SMRR. base = 0xc0000006, mask=0xff800800 |
| Relocation complete. |
| microcode: Update skipped, already up-to-date |
| New SMBASE 0xbffffc00 |
| In relocation handler: cpu 1 |
| New SMBASE=0xbffffc00 IEDBASE=0xc0400000 |
| Writing SMRR. base = 0xc0000006, mask=0xff800800 |
| Relocation complete. |
| microcode: Update skipped, already up-to-date |
| New SMBASE 0xbffff400 |
| In relocation handler: cpu 3 |
| New SMBASE=0xbffff400 IEDBASE=0xc0400000 |
| Writing SMRR. base = 0xc0000006, mask=0xff800800 |
| Relocation complete. |
| microcode: Update skipped, already up-to-date |
| New SMBASE 0xbffff800 |
| In relocation handler: cpu 2 |
| New SMBASE=0xbffff800 IEDBASE=0xc0400000 |
| Writing SMRR. base = 0xc0000006, mask=0xff800800 |
| Relocation complete. |
| microcode: Update skipped, already up-to-date |
| Initializing CPU #0 |
| CPU: vendor Intel device 206a7 |
| CPU: family 06, model 2a, stepping 07 |
| Enabling cache |
| CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz. |
| CPU: platform id 4 |
| CPU: cpuid(1) 0x206a7 |
| CPU: AES supported |
| CPU: TXT supported |
| CPU: VT supported |
| Setting up local APIC... |
| apic_id: 0x00 done. |
| VMX status: enabled |
| IA32_FEATURE_CONTROL status: locked |
| model_x06ax: energy policy set to 6 |
| model_x06ax: frequency set to 2800 |
| Turbo is available but hidden |
| Turbo has been enabled |
| CPU #0 initialized |
| Initializing CPU #1 |
| Initializing CPU #3 |
| Initializing CPU #2 |
| CPU: vendor Intel device 206a7 |
| CPU: family 06, model 2a, stepping 07 |
| CPU: vendor Intel device 206a7 |
| CPU: family 06, model 2a, stepping 07 |
| Enabling cache |
| CPU: vendor Intel device 206a7 |
| CPU: family 06, model 2a, stepping 07 |
| Enabling cache |
| CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz. |
| Enabling cache |
| CPU: platform id 4 |
| CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz. |
| CPU: cpuid(1) 0x206a7 |
| CPU: platform id 4 |
| CPU: AES supported |
| CPU: TXT supported |
| CPU: VT supported |
| CPU: cpuid(1) 0x206a7 |
| Setting up local APIC... |
| CPU: AES supported |
| CPU: TXT supported |
| CPU: VT supported |
| apic_id: 0x02 done. |
| Setting up local APIC... |
| VMX status: enabled |
| apic_id: 0x03 done. |
| IA32_FEATURE_CONTROL status: locked |
| VMX status: enabled |
| CPU: Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz. |
| IA32_FEATURE_CONTROL status: locked |
| CPU: platform id 4 |
| CPU: cpuid(1) 0x206a7 |
| CPU: AES supported |
| CPU: TXT supported |
| CPU: VT supported |
| model_x06ax: energy policy set to 6 |
| Setting up local APIC... |
| model_x06ax: frequency set to 2800 |
| apic_id: 0x01 done. |
| CPU #3 initialized |
| model_x06ax: energy policy set to 6 |
| VMX status: enabled |
| model_x06ax: frequency set to 2800 |
| CPU #2 initialized |
| IA32_FEATURE_CONTROL status: locked |
| model_x06ax: energy policy set to 6 |
| model_x06ax: frequency set to 2800 |
| CPU #1 initialized |
| bsp_do_flight_plan done after 9 msecs. |
| Initializing southbridge SMI... |
| SMI_STS: |
| GPE0_STS: GPIO15 GPIO14 GPIO11 GPIO9 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 |
| ALT_GP_SMI_STS: GPI14 GPI13 GPI11 GPI10 GPI9 GPI7 GPI6 GPI5 GPI4 GPI3 GPI1 GPI0 |
| TCO_STS: |
| Locking SMM. |
| CPU_CLUSTER: 0 init finished in 25488 usecs |
| PCI: 00:00.0 init ... |
| Disabling PEG12. |
| Disabling PEG11. |
| Disabling PEG10. |
| Disabling PEG60. |
| Disabling Device 7. |
| Disabling PEG IO clock. |
| Set BIOS_RESET_CPL |
| CPU TDP: 35 Watts |
| PCI: 00:00.0 init finished in 1024 usecs |
| PCI: 00:02.0 init ... |
| GT Power Management Init |
| SNB GT2 Power Meter Weights |
| GT Power Management Init (post VBIOS) |
| |
| [0.123831] CONFIG => |
| [0.123832] (Primary => |
| [0.123833] (Port => Internal, |
| [0.123833] Framebuffer => |
| [0.123834] (Width => 640, |
| [0.123835] Height => 400, |
| [0.123836] Start_X => 0, |
| [0.123837] Start_Y => 0, |
| [0.123838] Stride => 1, |
| [0.123839] V_Stride => 1, |
| [0.123840] Tiling => Linear , |
| [0.123841] Rotation => No_Rotation, |
| [0.123842] Offset => 0xffffffff, |
| [0.123843] BPC => 8), |
| [0.123844] Mode => |
| [0.123844] (Dotclock => 75200000, |
| [0.123846] H_Visible => 1366, |
| [0.123847] H_Sync_Begin => 1414, |
| [0.123848] H_Sync_End => 1478, |
| [0.123849] H_Total => 1582, |
| [0.123850] V_Visible => 768, |
| [0.123851] V_Sync_Begin => 772, |
| [0.123852] V_Sync_End => 779, |
| [0.123853] V_Total => 792, |
| [0.123854] H_Sync_Active_High => True, |
| [0.123855] V_Sync_Active_High => False, |
| [0.123856] BPC => 5)), |
| [0.123857] Secondary => |
| [0.123857] (Port => Disabled, |
| [0.123858] Framebuffer => |
| [0.123858] (Width => 1, |
| [0.123860] Height => 1, |
| [0.123861] Start_X => 0, |
| [0.123862] Start_Y => 0, |
| [0.123863] Stride => 1, |
| [0.123864] V_Stride => 1, |
| [0.123865] Tiling => Linear , |
| [0.123866] Rotation => No_Rotation, |
| [0.123867] Offset => 0x00000000, |
| [0.123868] BPC => 8), |
| [0.123868] Mode => |
| [0.123869] (Dotclock => 19200000, |
| [0.123870] H_Visible => 1, |
| [0.123871] H_Sync_Begin => 1, |
| [0.123872] H_Sync_End => 1, |
| [0.123873] H_Total => 1, |
| [0.123874] V_Visible => 1, |
| [0.123875] V_Sync_Begin => 1, |
| [0.123876] V_Sync_End => 1, |
| [0.123877] V_Total => 1, |
| [0.123878] H_Sync_Active_High => False, |
| [0.123879] V_Sync_Active_High => False, |
| [0.123880] BPC => 5)), |
| [0.123881] Tertiary => |
| [0.123881] (Port => Disabled, |
| [0.123882] Framebuffer => |
| [0.123882] (Width => 1, |
| [0.123883] Height => 1, |
| [0.123884] Start_X => 0, |
| [0.123885] Start_Y => 0, |
| [0.123886] Stride => 1, |
| [0.123887] V_Stride => 1, |
| [0.123888] Tiling => Linear , |
| [0.123889] Rotation => No_Rotation, |
| [0.123890] Offset => 0x00000000, |
| [0.123891] BPC => 8), |
| [0.123891] Mode => |
| [0.123892] (Dotclock => 19200000, |
| [0.123893] H_Visible => 1, |
| [0.123894] H_Sync_Begin => 1, |
| [0.123895] H_Sync_End => 1, |
| [0.123896] H_Total => 1, |
| [0.123897] V_Visible => 1, |
| [0.123898] V_Sync_Begin => 1, |
| [0.123899] V_Sync_End => 1, |
| [0.123900] V_Total => 1, |
| [0.123901] H_Sync_Active_High => False, |
| [0.123902] V_Sync_Active_High => False, |
| [0.123903] BPC => 5))); |
| PCI: 00:02.0 init finished in 72665 usecs |
| PCI: 00:04.0 init ... |
| PCI: 00:04.0 init finished in 0 usecs |
| PCI: 00:19.0 init ... |
| PCI: 00:19.0 init finished in 0 usecs |
| PCI: 00:1a.0 init ... |
| EHCI: Setting up controller.. done. |
| PCI: 00:1a.0 init finished in 13 usecs |
| PCI: 00:1b.0 init ... |
| Azalia: base = e1728000 |
| Azalia: codec_mask = 09 |
| Azalia: Initializing codec #3 |
| Azalia: codec viddid: 80862805 |
| Azalia: verb_size: 16 |
| Azalia: verb loaded. |
| Azalia: Initializing codec #0 |
| Azalia: codec viddid: 14f1506e |
| Azalia: verb_size: 52 |
| Azalia: verb loaded. |
| PCI: 00:1b.0 init finished in 4972 usecs |
| PCI: 00:1c.0 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.0 init finished in 8 usecs |
| PCI: 00:1c.1 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.1 init finished in 8 usecs |
| PCI: 00:1c.2 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.2 init finished in 10 usecs |
| PCI: 00:1c.3 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.3 init finished in 11 usecs |
| PCI: 00:1c.4 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.4 init finished in 8 usecs |
| PCI: 00:1c.5 init ... |
| Initializing PCH PCIe bridge. |
| PCI: 00:1c.5 init finished in 8 usecs |
| PCI: 00:1d.0 init ... |
| EHCI: Setting up controller.. done. |
| PCI: 00:1d.0 init finished in 13 usecs |
| PCI: 00:1f.0 init ... |
| pch: lpc_init |
| PCH: detected QM67, device id: 0x1c4f, rev id 0x5 |
| IOAPIC: Initializing IOAPIC at 0xfec00000 |
| IOAPIC: Bootstrap Processor Local APIC = 0x00 |
| IOAPIC: ID = 0x02 |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| Set power off after power failure. |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| NMI sources enabled. |
| CougarPoint PM init |
| RTC: failed = 0x0 |
| RTC Init |
| Disabling ACPI via APMC: |
| done. |
| pch_spi_init |
| PCI: 00:1f.0 init finished in 900 usecs |
| PCI: 00:1f.2 init ... |
| SATA: Initializing... |
| FMAP: area COREBOOT found @ 610200 (2031104 bytes) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| SATA: Controller in AHCI mode. |
| ABAR: e172e000 |
| PCI: 00:1f.2 init finished in 354 usecs |
| PCI: 00:1f.3 init ... |
| PCI: 00:1f.3 init finished in 7 usecs |
| PCI: 00:1f.6 init ... |
| PCI: 00:1f.6 init finished in 0 usecs |
| PCI: 02:00.0 init ... |
| PCI: 02:00.0 init finished in 0 usecs |
| PCI: 05:00.0 init ... |
| PCI: 05:00.0 init finished in 14 usecs |
| PCI: 06:00.0 init ... |
| PCI: 06:00.0 init finished in 0 usecs |
| PNP: 00ff.2 init ... |
| PNP: 00ff.2 init finished in 0 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:54 init ... |
| I2C: 01:54 init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:55 init ... |
| I2C: 01:55 init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:56 init ... |
| I2C: 01:56 init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:57 init ... |
| I2C: 01:57 init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:5c init ... |
| Locking EEPROM RFID |
| init EEPROM done |
| I2C: 01:5c init finished in 27364 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:5d init ... |
| I2C: 01:5d init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:5e init ... |
| I2C: 01:5e init finished in 1 usecs |
| smbus: PCI: 00:1f.3[0]->I2C: 01:5f init ... |
| I2C: 01:5f init finished in 1 usecs |
| Devices initialized |
| BS: BS_DEV_INIT times (us): entry 15663 run 133033 exit 0 |
| Finalize devices... |
| PCI: 00:1f.0 final |
| Devices finalized |
| BS: BS_POST_DEVICE times (us): entry 0 run 5 exit 0 |
| BS: BS_OS_RESUME_CHECK times (us): entry 0 run 2 exit 0 |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'fallback/dsdt.aml' |
| CBFS: Found @ offset 3c880 size 388f |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'fallback/slic' |
| CBFS: 'fallback/slic' not found. |
| ACPI: Writing ACPI tables at bff42000. |
| ACPI: * FACS |
| ACPI: * DSDT |
| ACPI: * FADT |
| ACPI: added table 1/32, length now 40 |
| ACPI: * SSDT |
| Found 1 CPU(s) with 4 core(s) each. |
| PSS: 2801MHz power 35000 control 0x2300 status 0x2300 |
| PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00 |
| PSS: 2400MHz power 28615 control 0x1800 status 0x1800 |
| PSS: 2000MHz power 22765 control 0x1400 status 0x1400 |
| PSS: 1600MHz power 17346 control 0x1000 status 0x1000 |
| PSS: 1200MHz power 12373 control 0xc00 status 0xc00 |
| PSS: 800MHz power 7830 control 0x800 status 0x800 |
| PSS: 2801MHz power 35000 control 0x2300 status 0x2300 |
| PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00 |
| PSS: 2400MHz power 28615 control 0x1800 status 0x1800 |
| PSS: 2000MHz power 22765 control 0x1400 status 0x1400 |
| PSS: 1600MHz power 17346 control 0x1000 status 0x1000 |
| PSS: 1200MHz power 12373 control 0xc00 status 0xc00 |
| PSS: 800MHz power 7830 control 0x800 status 0x800 |
| PSS: 2801MHz power 35000 control 0x2300 status 0x2300 |
| PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00 |
| PSS: 2400MHz power 28615 control 0x1800 status 0x1800 |
| PSS: 2000MHz power 22765 control 0x1400 status 0x1400 |
| PSS: 1600MHz power 17346 control 0x1000 status 0x1000 |
| PSS: 1200MHz power 12373 control 0xc00 status 0xc00 |
| PSS: 800MHz power 7830 control 0x800 status 0x800 |
| PSS: 2801MHz power 35000 control 0x2300 status 0x2300 |
| PSS: 2800MHz power 35000 control 0x1c00 status 0x1c00 |
| PSS: 2400MHz power 28615 control 0x1800 status 0x1800 |
| PSS: 2000MHz power 22765 control 0x1400 status 0x1400 |
| PSS: 1600MHz power 17346 control 0x1000 status 0x1000 |
| PSS: 1200MHz power 12373 control 0xc00 status 0xc00 |
| PSS: 800MHz power 7830 control 0x800 status 0x800 |
| Generating ACPI PIRQ entries |
| \_SB.PCI0.LPCB.TPM: LPC TPM PNP: 0c31.0 |
| ACPI: * H8 |
| H8: BDC detection not implemented. Assuming BDC installed |
| H8: WWAN not installed |
| ACPI: added table 2/32, length now 44 |
| ACPI: * MCFG |
| ACPI: added table 3/32, length now 48 |
| ACPI: * TCPA |
| TCPA log created at bff31000 |
| ACPI: added table 4/32, length now 52 |
| ACPI: * MADT |
| ACPI: added table 5/32, length now 56 |
| current = bff47800 |
| ACPI: * DMAR |
| ACPI: added table 6/32, length now 60 |
| current = bff478d0 |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'vbt.bin' |
| CBFS: Found @ offset 37280 size 578 |
| Found a VBT of 3985 bytes after decompression |
| GMA: Found VBT in CBFS |
| GMA: Found valid VBT in CBFS |
| ACPI: * HPET |
| ACPI: added table 7/32, length now 64 |
| ACPI: done. |
| ACPI tables: 30992 bytes. |
| smbios_write_tables: bff30000 |
| Create SMBIOS type 17 |
| SMBIOS tables: 788 bytes. |
| Writing table forward entry at 0x00000500 |
| Wrote coreboot table at: 00000500, 0x10 bytes, checksum dfe7 |
| Writing coreboot table at 0xbff66000 |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'cmos_layout.bin' |
| CBFS: Found @ offset 37840 size 738 |
| 0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES |
| 1. 0000000000001000-000000000009ffff: RAM |
| 2. 00000000000a0000-00000000000fffff: RESERVED |
| 3. 0000000000100000-000000001fffffff: RAM |
| 4. 0000000020000000-00000000201fffff: RESERVED |
| 5. 0000000020200000-000000003fffffff: RAM |
| 6. 0000000040000000-00000000401fffff: RESERVED |
| 7. 0000000040200000-00000000bff2ffff: RAM |
| 8. 00000000bff30000-00000000bff7efff: CONFIGURATION TABLES |
| 9. 00000000bff7f000-00000000bffcdfff: RAMSTAGE |
| 10. 00000000bffce000-00000000bfffffff: CONFIGURATION TABLES |
| 11. 00000000c0000000-00000000c29fffff: RESERVED |
| 12. 00000000f0000000-00000000f3ffffff: RESERVED |
| 13. 00000000fed40000-00000000fed44fff: RESERVED |
| 14. 00000000fed90000-00000000fed91fff: RESERVED |
| 15. 0000000100000000-000000023d5fffff: RAM |
| Manufacturer: c2 |
| SF: Detected MX25L6405D with sector size 0x1000, total 0x800000 |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| Wrote coreboot table at: bff66000, 0xb00 bytes, checksum 2e30 |
| coreboot table: 2840 bytes. |
| IMD ROOT 0. bffff000 00001000 |
| IMD SMALL 1. bfffe000 00001000 |
| CONSOLE 2. bffde000 00020000 |
| TIME STAMP 3. bffdd000 00000910 |
| ROMSTG STCK 4. bffd8000 00005000 |
| AFTER CAR 5. bffce000 0000a000 |
| RAMSTAGE 6. bff7e000 00050000 |
| SMM BACKUP 7. bff6e000 00010000 |
| COREBOOT 8. bff66000 00008000 |
| ACPI 9. bff42000 00024000 |
| ACPI GNVS 10. bff41000 00001000 |
| TCPA TCGLOG11. bff31000 00010000 |
| SMBIOS 12. bff30000 00000800 |
| IMD small region: |
| IMD ROOT 0. bfffec00 00000400 |
| USBDEBUG 1. bfffeba0 00000050 |
| MEM INFO 2. bfffe9e0 000001a9 |
| ROMSTAGE 3. bfffe9c0 00000004 |
| COREBOOTFWD 4. bfffe980 00000028 |
| BS: BS_WRITE_TABLES times (us): entry 0 run 26367 exit 0 |
| CBFS: 'Master Header Locator' located CBFS at [610200:800000) |
| CBFS: Locating 'fallback/payload' |
| CBFS: Found @ offset 40180 size 6399c |
| Checking segment from ROM address 0xffe503b8 |
| Checking segment from ROM address 0xffe503d4 |
| Checking segment from ROM address 0xffe503f0 |
| Loading segment from ROM address 0xffe503b8 |
| code (compression=1) |
| New segment dstaddr 0x00008200 memsize 0x1b988 srcaddr 0xffe5040c filesize 0x99fd |
| Loading Segment: addr: 0x00008200 memsz: 0x000000000001b988 filesz: 0x00000000000099fd |
| using LZMA |
| Clearing Segment: addr: 0x000000000001c143 memsz: 0x0000000000007a45 |
| Loading segment from ROM address 0xffe503d4 |
| code (compression=1) |
| New segment dstaddr 0x00100000 memsize 0x125694 srcaddr 0xffe59e09 filesize 0x59f4b |
| Loading Segment: addr: 0x00100000 memsz: 0x0000000000125694 filesz: 0x0000000000059f4b |
| using LZMA |
| Loading segment from ROM address 0xffe503f0 |
| Entry Point 0x00008200 |
| BS: BS_PAYLOAD_LOAD times (us): entry 0 run 146300 exit 0 |
| ICH-NM10-PCH: watchdog disabled |
| Jumping to boot code at 00008200(bff66000) |
| error: no suitable video mode found. |
|
error: file `/boot/grub/i386-coreboot/jpeg.mod' not found. |
|
error: file `/boot/grub/i386-coreboot/gfxterm_background.mod' not found. |
|
error: file `/dejavusansmono.pf2' not found. |
|
error: file `/boot/grub/layouts/usqwerty.gkb' not found. |
|
GNU GRUB version 2.02 |
|
|
|
+----------------------------------------------------------------------------+||||||||||||||||||||||||+----------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. |
|
Press enter to boot the selected OS, `e' to edit the commands |
|
before booting or `c' for a command-line. *Load Operating System (incl. fully encrypted disks) [o] ? Search ISOLINUX menu (AHCI) [a] ? Search ISOLINUX menu (USB) [u] ? Search ISOLINUX menu (CD/DVD) [d] ? Load test configuration (grubtest.cfg) inside of CBFS [t] ? Search for GRUB2 configuration on external media [s] ? Poweroff [p] ? Reboot [r] ? ? ? ? ? The highlighted entry will be executed automatically in 1s. error: file `/boot/grub/fonts/unicode.pf2' not found. |
|
error: no suitable video mode found. |
|
GNU GRUB version 2.02 |
|
|
|
+----------------------------------------------------------------------------+||||||||||||||||||||||+----------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. |
|
Press enter to boot the selected OS, `e' to edit the commands |
|
before booting or `c' for a command-line. ESC to return |
|
previous menu. *Gentoo GNU/Linux ? Advanced options for Gentoo GNU/Linux ? MemTest86 ? Memtest86+ ? ? ? ? ? ? ? ? The highlighted entry will be executed automatically in 5s. error: file `/boot/grub/i386-coreboot/all_video.mod' not found. |
|
Loading Linux 5.1.5-gentoo ... |
|
Loading initial ramdisk ... |
|
|
|
Press any key to continue... |
|
|