blob: f32bdb49841272609288bfa4324784592301397c [file] [log] [blame]
/*
* This file is part of the flashrom project.
*
* Copyright (C) 2015 Joseph C. Lehner <joseph.c.lehner@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#if defined(__i386__) || defined(__x86_64__)
#include <string.h>
#include <stdlib.h>
#include "flash.h"
#include "programmer.h"
#include "hwaccess.h"
#define MAX_ROM_DECODE (32 * 1024)
#define ADDR_MASK (MAX_ROM_DECODE - 1)
/*
* In the absence of any public docs on the PDC2026x family, this programmer was created through a mix of
* reverse-engineering and trial and error.
*
* The only device tested is an Ultra100 controller, but the logic for programming the other 2026x controllers
* is the same, so it should, in theory, work for those as well.
*
* While the tested Ultra100 controller used a 128 kB MX29F001T chip, A16 and A15 showed continuity to ground,
* thus limiting the the programmer on this card to 32 kB. Without other controllers to test this programmer on,
* this is currently a hard limit. Note that ROM files for these controllers are 16 kB only.
*
* Since flashrom does not support accessing flash chips larger than the size limit of the programmer (the
* tested Ultra100 uses a 128 kB MX29F001T chip), the chip size is hackishly adjusted in atapromise_limit_chip.
*/
static uint32_t io_base_addr = 0;
static uint32_t rom_base_addr = 0;
static uint8_t *atapromise_bar = NULL;
static size_t rom_size = 0;
const struct dev_entry ata_promise[] = {
{0x105a, 0x4d38, NT, "Promise", "PDC20262 (FastTrak66/Ultra66)"},
{0x105a, 0x0d30, NT, "Promise", "PDC20265 (FastTrak100 Lite/Ultra100)"},
{0x105a, 0x4d30, OK, "Promise", "PDC20267 (FastTrak100/Ultra100)"},
{0},
};
static void atapromise_chip_writeb(const struct flashctx *flash, uint8_t val, chipaddr addr);
static uint8_t atapromise_chip_readb(const struct flashctx *flash, const chipaddr addr);
static const struct par_master par_master_atapromise = {
.chip_readb = atapromise_chip_readb,
.chip_readw = fallback_chip_readw,
.chip_readl = fallback_chip_readl,
.chip_readn = fallback_chip_readn,
.chip_writeb = atapromise_chip_writeb,
.chip_writew = fallback_chip_writew,
.chip_writel = fallback_chip_writel,
.chip_writen = fallback_chip_writen,
};
void *atapromise_map(const char *descr, uintptr_t phys_addr, size_t len)
{
/* In case fallback_map ever returns something other than NULL. */
return NULL;
}
static void atapromise_limit_chip(struct flashchip *chip)
{
unsigned int i, size;
unsigned int usable_erasers = 0;
size = chip->total_size * 1024;
/* Chip is small enough or already limited. */
if (size <= rom_size)
return;
/* Undefine all block_erasers that don't operate on the whole chip,
* and adjust the eraseblock size of those which do.
*/
for (i = 0; i < NUM_ERASEFUNCTIONS; ++i) {
if (chip->block_erasers[i].eraseblocks[0].size != size) {
chip->block_erasers[i].eraseblocks[0].count = 0;
chip->block_erasers[i].block_erase = NULL;
} else {
chip->block_erasers[i].eraseblocks[0].size = rom_size;
usable_erasers++;
}
}
if (usable_erasers) {
chip->total_size = rom_size / 1024;
if (chip->page_size > rom_size)
chip->page_size = rom_size;
} else {
msg_pdbg("Failed to adjust size of chip \"%s\" (%d kB).\n", chip->name, chip->total_size);
}
}
int atapromise_init(void)
{
struct pci_dev *dev = NULL;
if (rget_io_perms())
return 1;
dev = pcidev_init(ata_promise, PCI_BASE_ADDRESS_4);
if (!dev)
return 1;
io_base_addr = pcidev_readbar(dev, PCI_BASE_ADDRESS_4) & 0xfffe;
if (!io_base_addr) {
return 1;
}
/* Not exactly sure what this does, because flashing seems to work
* well without it. However, PTIFLASH does it, so we do it too.
*/
OUTB(1, io_base_addr + 0x10);
rom_base_addr = pcidev_readbar(dev, PCI_BASE_ADDRESS_5);
if (!rom_base_addr) {
msg_pdbg("Failed to read BAR5\n");
return 1;
}
rom_size = dev->rom_size > MAX_ROM_DECODE ? MAX_ROM_DECODE : dev->rom_size;
atapromise_bar = (uint8_t*)rphysmap("Promise", rom_base_addr, rom_size);
if (atapromise_bar == ERROR_PTR) {
return 1;
}
max_rom_decode.parallel = rom_size;
register_par_master(&par_master_atapromise, BUS_PARALLEL, NULL);
msg_pwarn("Do not use this device as a generic programmer. It will leave anything outside\n"
"the first %zu kB of the flash chip in an undefined state. It works fine for the\n"
"purpose of updating the firmware of this device (padding may necessary).\n",
rom_size / 1024);
return 0;
}
static void atapromise_chip_writeb(const struct flashctx *flash, uint8_t val, chipaddr addr)
{
uint32_t data;
atapromise_limit_chip(flash->chip);
data = (rom_base_addr + (addr & ADDR_MASK)) << 8 | val;
OUTL(data, io_base_addr + 0x14);
}
static uint8_t atapromise_chip_readb(const struct flashctx *flash, const chipaddr addr)
{
atapromise_limit_chip(flash->chip);
return pci_mmio_readb(atapromise_bar + (addr & ADDR_MASK));
}
#else
#error PCI port I/O access is not supported on this architecture yet.
#endif