src/mainboard/gigabyte/ma785gmt/romstage.c

/*
 * This file is part of the coreboot project.
 *
 * Copyright (C) 2010 Wang Qing Pei <wangqingpei@gmail.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
 */

//#define SYSTEM_TYPE 0	/* SERVER */
#define SYSTEM_TYPE 1	/* DESKTOP */
//#define SYSTEM_TYPE 2	/* MOBILE */

#include <stdint.h>
#include <string.h>
#include <device/pci_def.h>
#include <device/pci_ids.h>
#include <arch/io.h>
#include <device/pnp_def.h>
#include <cpu/x86/lapic.h>
#include <console/console.h>
#include <cpu/amd/model_10xxx_rev.h>
#include <northbridge/amd/amdfam10/raminit.h>
#include <northbridge/amd/amdfam10/amdfam10.h>
#include <lib.h>
#include <cpu/x86/lapic.h>
#include "northbridge/amd/amdfam10/reset_test.c"
#include <console/loglevel.h>
#include <cpu/x86/bist.h>
#include <superio/ite/common/ite.h>
#include <superio/ite/it8718f/it8718f.h>
#include <cpu/amd/mtrr.h>
#include "northbridge/amd/amdfam10/setup_resource_map.c"
#include "southbridge/amd/rs780/early_setup.c"
#include <southbridge/amd/sb700/sb700.h>
#include <southbridge/amd/sb700/smbus.h>
#include "northbridge/amd/amdfam10/debug.c"

#define SERIAL_DEV PNP_DEV(0x2e, IT8718F_SP1)
#define GPIO_DEV PNP_DEV(0x2e, IT8718F_GPIO)

static void activate_spd_rom(const struct mem_controller *ctrl) { }

static int spd_read_byte(u32 device, u32 address)
{
	return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
}

#include <northbridge/amd/amdfam10/amdfam10.h>
#include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c"
#include "northbridge/amd/amdfam10/pci.c"
#include "resourcemap.c"
#include "cpu/amd/quadcore/quadcore.c"
#include <cpu/amd/microcode.h>

#include "cpu/amd/model_10xxx/init_cpus.c"
#include "northbridge/amd/amdfam10/early_ht.c"
#include <spd.h>

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
	u32 bsp_apicid = 0, val;
	msr_t msr;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		sb7xx_51xx_pci_port80();
	}

	post_code(0x30);

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
		/* All cores run this but the BSP(node0,core0) is the only core that returns. */
	}

	post_code(0x32);

	enable_rs780_dev8();
	sb7xx_51xx_lpc_init();

	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	it8718f_disable_reboot(GPIO_DEV);
	console_init();

//	dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	// Load MPB
	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR();
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	   It would be nice to fixup prink spinlocks for ROM XIP mode.
	   I think it could be done by putting the spinlock flag in the cache
	   of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores();
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

	post_code(0x38);

	/* run _early_setup before soft-reset. */
	rs780_early_setup();
	sb7xx_51xx_early_setup();

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	   need to be done once.*/
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {			// BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);	// BSP is node 0
	}

	post_code(0x3A);

	/* show final fid and vid */
	msr=rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif

	rs780_htinit();

	/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
	if (!warm_reset_detect(0)) {
		printk(BIOS_INFO, "...WARM RESET...\n\n\n");
		soft_reset();
		die("After soft_reset_x - shouldn't see this message!!!\n");
	}

	post_code(0x3B);

	/* It's the time to set ctrl in sysinfo now; */
	printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	post_code(0x40);

//	die("Die Before MCT init.");

	printk(BIOS_DEBUG, "raminit_amdmct()\n");
	raminit_amdmct(sysinfo);
	cbmem_initialize_empty();
	post_code(0x41);

/*
	dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
*/

//	die("After MCT init before CAR disabled.");

	rs780_before_pci_init();
	sb7xx_51xx_before_pci_init();

	post_code(0x42);
	post_cache_as_ram();	// BSP switch stack to ram, copy then execute LB.
	post_code(0x43);	// Should never see this post code.
}

/**
 * BOOL AMD_CB_ManualBUIDSwapList(u8 Node, u8 Link, u8 **List)
 * Description:
 *	This routine is called every time a non-coherent chain is processed.
 *	BUID assignment may be controlled explicitly on a non-coherent chain. Provide a
 *	swap list. The first part of the list controls the BUID assignment and the
 *	second part of the list provides the device to device linking.  Device orientation
 *	can be detected automatically, or explicitly.  See documentation for more details.
 *
 *	Automatic non-coherent init assigns BUIDs starting at 1 and incrementing sequentially
 *	based on each device's unit count.
 *
 * Parameters:
 *	@param[in]  node   = The node on which this chain is located
 *	@param[in]  link   = The link on the host for this chain
 *	@param[out] List   = supply a pointer to a list
 */
BOOL AMD_CB_ManualBUIDSwapList (u8 node, u8 link, const u8 **List)
{
	static const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF };
	/* If the BUID was adjusted in early_ht we need to do the manual override */
	if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) {
		printk(BIOS_DEBUG, "AMD_CB_ManualBUIDSwapList()\n");
		if ((node == 0) && (link == 0)) {	/* BSP SB link */
			*List = swaplist;
			return 1;
		}
	}

	return 0;
}