fix newly introduced printk_foo warnings..
Interesting enough, console_printk was only used in a single place and
duplicated a large part of console.h which is included in the same place.
Thus, just drop console_printk.c and we're one down with console complexity
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
diff --git a/src/southbridge/amd/rs780/rs780_gfx.c b/src/southbridge/amd/rs780/rs780_gfx.c
index 2ec0683..066dc60 100644
--- a/src/southbridge/amd/rs780/rs780_gfx.c
+++ b/src/southbridge/amd/rs780/rs780_gfx.c
@@ -55,7 +55,7 @@
static void clkind_write(device_t dev, u32 index, u32 data)
{
u32 gfx_bar2 = pci_read_config32(dev, 0x18) & ~0xF;
- /* printk(BIOS_INFO, "gfx bar 2 %02x\n", gfx_bar2); */
+ /* printk(BIOS_DEBUG, "gfx bar 2 %02x\n", gfx_bar2); */
*(u32*)(gfx_bar2+CLK_CNTL_INDEX) = index | 1<<7;
*(u32*)(gfx_bar2+CLK_CNTL_DATA) = data;
@@ -67,7 +67,7 @@
*/
static void rs780_gfx_read_resources(device_t dev)
{
- printk(BIOS_INFO, "rs780_gfx_read_resources.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_read_resources.\n");
/* The initial value of 0x24 is 0xFFFFFFFF, which is confusing.
Even if we write 0xFFFFFFFF into it, it will be 0xFFF00000,
@@ -307,7 +307,7 @@
deviceid = pci_read_config16(dev, PCI_DEVICE_ID);
vendorid = pci_read_config16(dev, PCI_VENDOR_ID);
- printk(BIOS_INFO, "internal_gfx_pci_dev_init device=%x, vendor=%x.\n",
+ printk(BIOS_DEBUG, "internal_gfx_pci_dev_init device=%x, vendor=%x.\n",
deviceid, vendorid);
command = pci_read_config16(dev, 0x04);
@@ -583,10 +583,10 @@
u32 FB_Start, FB_End;
#endif
- printk(BIOS_INFO, "rs780_internal_gfx_enable dev = 0x%p, nb_dev = 0x%p.\n", dev, nb_dev);
+ printk(BIOS_DEBUG, "rs780_internal_gfx_enable dev = 0x%p, nb_dev = 0x%p.\n", dev, nb_dev);
sysmem = rdmsr(0xc001001a);
- printk(BIOS_INFO, "sysmem = %x_%x\n", sysmem.hi, sysmem.lo);
+ printk(BIOS_DEBUG, "sysmem = %x_%x\n", sysmem.hi, sysmem.lo);
/* The system top memory in 780. */
pci_write_config32(nb_dev, 0x90, sysmem.lo);
@@ -824,12 +824,12 @@
struct southbridge_amd_rs780_config *cfg =
(struct southbridge_amd_rs780_config *)nb_dev->chip_info;
- printk(BIOS_INFO, "rs780_gfx_init single_port_configuration.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init single_port_configuration.\n");
/* step 12 training, releases hold training for GFX port 0 (device 2) */
PcieReleasePortTraining(nb_dev, dev, 2);
result = PcieTrainPort(nb_dev, dev, 2);
- printk(BIOS_INFO, "rs780_gfx_init single_port_configuration step12.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init single_port_configuration step12.\n");
/* step 13 Power Down Control */
/* step 13.1 Enables powering down transmitter and receiver pads along with PLL macros. */
@@ -866,11 +866,11 @@
break;
}
}
- printk(BIOS_INFO, "rs780_gfx_init single_port_configuration step13.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init single_port_configuration step13.\n");
/* step 14 Reset Enumeration Timer, disables the shortening of the enumeration timer */
set_pcie_enable_bits(dev, 0x70, 1 << 19, 1 << 19);
- printk(BIOS_INFO, "rs780_gfx_init single_port_configuration step14.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init single_port_configuration step14.\n");
}
static void dual_port_configuration(device_t nb_dev, device_t dev)
@@ -980,7 +980,7 @@
struct southbridge_amd_rs780_config *cfg =
(struct southbridge_amd_rs780_config *)nb_dev->chip_info;
- printk(BIOS_INFO, "rs780_gfx_init, nb_dev=0x%p, dev=0x%p, port=0x%x.\n",
+ printk(BIOS_DEBUG, "rs780_gfx_init, nb_dev=0x%p, dev=0x%p, port=0x%x.\n",
nb_dev, dev, port);
/* GFX Core Initialization */
@@ -1003,7 +1003,7 @@
set_nbmisc_enable_bits(nb_dev, 0x28, 3 << 6 | 3 << 8 | 3 << 10,
1 << 6 | 1 << 8 | 1 << 10);
reg32 = nbmisc_read_index(nb_dev, 0x28);
- printk(BIOS_INFO, "misc 28 = %x\n", reg32);
+ printk(BIOS_DEBUG, "misc 28 = %x\n", reg32);
/* 5.9.1.6.Selects the single ended GFX REFCLK to be the source for core logic. */
set_nbmisc_enable_bits(nb_dev, 0x6C, 1 << 31, 1 << 31);
@@ -1021,7 +1021,7 @@
set_nbmisc_enable_bits(nb_dev, 0x28, 3 << 6 | 3 << 8 | 3 << 10,
0);
reg32 = nbmisc_read_index(nb_dev, 0x28);
- printk(BIOS_INFO, "misc 28 = %x\n", reg32);
+ printk(BIOS_DEBUG, "misc 28 = %x\n", reg32);
/* 5.9.1.6.Selects the single ended GFX REFCLK to be the source for core logic. */
set_nbmisc_enable_bits(nb_dev, 0x6C, 1 << 31, 0 << 31);
@@ -1062,7 +1062,7 @@
/* release hold training for device 2. GFX initialization is done. */
set_nbmisc_enable_bits(nb_dev, 0x8, 1 << 4, 0 << 4);
dynamic_link_width_control(nb_dev, dev, cfg->gfx_link_width);
- printk(BIOS_INFO, "rs780_gfx_init step7.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step7.\n");
return;
}
@@ -1070,11 +1070,11 @@
/* 5.9.12.1 sets RCB timeout to be 25ms */
/* 5.9.12.2. RCB Cpl timeout on link down. */
set_pcie_enable_bits(dev, 0x70, 7 << 16 | 1 << 19, 4 << 16 | 1 << 19);
- printk(BIOS_INFO, "rs780_gfx_init step5.9.12.1.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step5.9.12.1.\n");
/* step 5.9.12.3 disables slave ordering logic */
set_pcie_enable_bits(nb_dev, 0x20, 1 << 8, 1 << 8);
- printk(BIOS_INFO, "rs780_gfx_init step5.9.12.3.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step5.9.12.3.\n");
/* step 5.9.12.4 sets DMA payload size to 64 bytes */
set_pcie_enable_bits(nb_dev, 0x10, 7 << 10, 4 << 10);
@@ -1096,7 +1096,7 @@
/* 5.9.12.9 CMGOOD_OVERRIDE for end point initiated lane degradation. */
set_nbmisc_enable_bits(nb_dev, 0x6a, 1 << 17, 1 << 17);
- printk(BIOS_INFO, "rs780_gfx_init step5.9.12.9.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step5.9.12.9.\n");
/* 5.9.12.10 Sets the timer in Config state from 20us to */
/* 5.9.12.11 De-asserts RX_EN in L0s. */
@@ -1169,15 +1169,14 @@
if (cfg->gfx_lane_reversal) {
set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 2, 1 << 2);
}
- printk_info("rs780_gfx_init step1.\n");
- printk_info("rs780_gfx_init step2.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step1.\n");
- printk_info("device = %x\n", dev->path.pci.devfn >> 3);
- if((dev->path.pci.devfn >> 3) == 2)
+ printk(BIOS_DEBUG, "device = %x\n", dev->path.pci.devfn >> 3);
+ if((dev->path.pci.devfn >> 3) == 2) {
single_port_configuration(nb_dev, dev);
- else{
+ } else {
set_nbmisc_enable_bits(nb_dev, 0xc, 0, 0x2 << 2); /* hide the GFX bridge. */
- printk_info("If dev3.., single port. Do nothing.\n");
+ printk(BIOS_INFO, "Single port. Do nothing.\n"); // If dev3
}
break;
@@ -1187,17 +1186,17 @@
set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 2, 1 << 2);
set_nbmisc_enable_bits(nb_dev, 0x33, 1 << 3, 1 << 3);
}
- printk_info("rs780_gfx_init step1.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step1.\n");
/* step 1.1, dual-slot gfx configuration (only need if CMOS option is enabled) */
/* AMD calls the configuration CrossFire */
set_nbmisc_enable_bits(nb_dev, 0x0, 0xf << 8, 5 << 8);
- printk_info("rs780_gfx_init step2.\n");
+ printk(BIOS_DEBUG, "rs780_gfx_init step2.\n");
- printk_info("device = %x\n", dev->path.pci.devfn >> 3);
+ printk(BIOS_DEBUG, "device = %x\n", dev->path.pci.devfn >> 3);
dual_port_configuration(nb_dev, dev);
break;
default:
- printk(BIOS_INFO, "Incorrect configuration of external gfx slot.\n");
+ printk(BIOS_INFO, "Incorrect configuration of external GFX slot.\n");
break;
}
}
diff --git a/src/southbridge/intel/i82801dx/i82801dx_lpc.c b/src/southbridge/intel/i82801dx/i82801dx_lpc.c
index c57bf09..652d6d0 100644
--- a/src/southbridge/intel/i82801dx/i82801dx_lpc.c
+++ b/src/southbridge/intel/i82801dx/i82801dx_lpc.c
@@ -133,7 +133,7 @@
reg8 &= ~(1 << 3); /* minimum asssertion is 1 to 2 RTCCLK */
pci_write_config8(dev, GEN_PMCON_3, reg8);
- printk_info("Set power %s after power failure.\n", state);
+ printk(BIOS_INFO, "Set power %s after power failure.\n", state);
/* Set up NMI on errors. */
reg8 = inb(0x61);
@@ -147,10 +147,10 @@
nmi_option = NMI_OFF;
get_option(&nmi_option, "nmi");
if (nmi_option) {
- printk_info ("NMI sources enabled.\n");
+ printk(BIOS_INFO, "NMI sources enabled.\n");
reg8 &= ~(1 << 7); /* Set NMI. */
} else {
- printk_info ("NMI sources disabled.\n");
+ printk(BIOS_INFO, "NMI sources disabled.\n");
reg8 |= ( 1 << 7); /* Disable NMI. */
}
outb(reg8, 0x70);
@@ -232,7 +232,7 @@
u32 reg32, hpet, val;
/* Set HPET base address and enable it */
- printk_debug("Enabling HPET at 0x%x\n", HPET_ADDR);
+ printk(BIOS_DEBUG, "Enabling HPET at 0x%x\n", HPET_ADDR);
reg32 = pci_read_config32(dev, GEN_CNTL);
/*
* Bit 17 is HPET enable bit.
@@ -253,9 +253,9 @@
val &= 0x7;
if ((val & 0x4) && (hpet == (val & 0x3))) {
- printk_debug("HPET enabled at 0x%x\n", HPET_ADDR);
+ printk(BIOS_INFO, "HPET enabled at 0x%x\n", HPET_ADDR);
} else {
- printk_err("HPET was not enabled correctly\n");
+ printk(BIOS_WARNING, "HPET was not enabled correctly\n");
reg32 &= ~(1 << 17); /* Clear Enable */
pci_write_config32(dev, GEN_CNTL, reg32);
}