mb/google/volteer: Update I2C5 bus freq and devicetree.
Update lindar gpio settings for Synaptics trackpad no function issue.
Update I2C5 bus freq to 400kHz.
Improve Goodix Touchscreen power on sequence.
BUG=b:160013582
BRANCH=firmware-volteer-13521.B
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device. Verify trackpad function workable.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I8c1ab6bab1f9de187e2a78ead7b5bbaf758f5fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
diff --git a/src/mainboard/google/volteer/variants/lindar/overridetree.cb b/src/mainboard/google/volteer/variants/lindar/overridetree.cb
index 2e61071..277ba60 100644
--- a/src/mainboard/google/volteer/variants/lindar/overridetree.cb
+++ b/src/mainboard/google/volteer/variants/lindar/overridetree.cb
@@ -9,6 +9,41 @@
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)" # USB3/2 Type A port A0
register "SaGv" = "SaGv_Disabled"
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT |
+ #| GSPI0 | cr50 TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| | before memory is up |
+ #| GSPI1 | Fingerprint MCU |
+ #| I2C0 | Audio |
+ #| I2C1 | Touchscreen |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
+ .gspi[0] = {
+ .speed_mhz = 1,
+ .early_init = 1,
+ },
+ .i2c[0] = {
+ .speed = I2C_SPEED_FAST,
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 163,
+ .scl_hcnt = 75,
+ .sda_hold = 36,
+ },
+ },
+ }"
# I2C Port Config
register "SerialIoI2cMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
@@ -69,8 +104,8 @@
# Parameter T2 >= 1ms
register "generic.reset_off_delay_ms" = "3"
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)"
- # Parameter T1 >= 10ms
- register "generic.enable_delay_ms" = "12"
+ # Parameter T1 >= 20ms
+ register "generic.enable_delay_ms" = "20"
register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)"
# Parameter T4 >= 1ms
register "generic.stop_off_delay_ms" = "1"