mb/google/nissa/variant/sundance: Update devicetree settings
Based on schematic and gpio table of sundance, generate overridetree.cb
settings for sundance.
BUG=b:328505938
TEST=FW_NAME=sundance emerge-nissa coreboot chromeos-bootimage
Change-Id: I857be7bc7f98281cac57fef85bf9f3cef2ec14e9
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
diff --git a/src/mainboard/google/brya/Kconfig b/src/mainboard/google/brya/Kconfig
index 160d12a..732a9ea 100644
--- a/src/mainboard/google/brya/Kconfig
+++ b/src/mainboard/google/brya/Kconfig
@@ -384,6 +384,7 @@
config BOARD_GOOGLE_SUNDANCE
select BOARD_GOOGLE_BASEBOARD_NISSA
+ select DRIVERS_GENERIC_GPIO_KEYS
config BOARD_GOOGLE_QUANDISO
select BOARD_GOOGLE_BASEBOARD_NISSA
diff --git a/src/mainboard/google/brya/variants/sundance/overridetree.cb b/src/mainboard/google/brya/variants/sundance/overridetree.cb
index 4f2c04a..30c93e4 100644
--- a/src/mainboard/google/brya/variants/sundance/overridetree.cb
+++ b/src/mainboard/google/brya/variants/sundance/overridetree.cb
@@ -1,6 +1,346 @@
chip soc/intel/alderlake
+ # Acoustic settings
+ register "acoustic_noise_mitigation" = "1"
+ register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8"
+ register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8"
+ register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1"
+ register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1"
+ register "PreWake" = "100"
- device domain 0 on
- end
+ register "sagv" = "SaGv_Enabled"
+ # EMMC Tx CMD Delay
+ # Refer to EDS-Vol2-42.3.7.
+ # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39.
+ # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39.
+ register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505"
+
+ # EMMC TX DATA Delay 1
+ # Refer to EDS-Vol2-42.3.8.
+ # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78.
+ # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79.
+ register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909"
+
+ # EMMC TX DATA Delay 2
+ # Refer to EDS-Vol2-42.3.9.
+ # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79.
+ # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
+ # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79.
+ # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79.
+ register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828"
+
+ # EMMC RX CMD/DATA Delay 1
+ # Refer to EDS-Vol2-42.3.10.
+ # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119.
+ # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
+ # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119.
+ # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119.
+ register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B"
+
+ # EMMC RX CMD/DATA Delay 2
+ # Refer to EDS-Vol2-42.3.12.
+ # [17:16] stands for Rx Clock before Output Buffer,
+ # 00: Rx clock after output buffer,
+ # 01: Rx clock before output buffer,
+ # 10: Automatic selection based on working mode.
+ # 11: Reserved
+ # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39.
+ # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79.
+ register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023"
+
+ # EMMC Rx Strobe Delay
+ # Refer to EDS-Vol2-42.3.11.
+ # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39.
+ # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
+ register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515"
+
+ # SOC Aux orientation override:
+ # This is a bitfield that corresponds to up to 4 TCSS ports.
+ # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
+ # TcssAuxOri = 0101b
+ # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports
+ # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the
+ # motherboard to USBC connector
+ register "tcss_aux_ori" = "5"
+
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+ register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
+
+ register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0
+ register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C1
+ register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # WWAN
+ register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WFC Camera
+ register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN
+ register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
+
+ register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 port for WWAN
+
+ # Configure external V1P05/Vnn/VnnSx Rails for Sundance
+ register "ext_fivr_settings" = "{
+ .configure_ext_fivr = 1,
+ .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
+ .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
+ .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
+ .v1p05_voltage_mv = 1050,
+ .vnn_voltage_mv = 780,
+ .vnn_sx_voltage_mv = 1050,
+ .v1p05_icc_max_ma = 500,
+ .vnn_icc_max_ma = 500,
+ }"
+
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C1 | Touchscreen |
+ #| I2C3 | Audio |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST_PLUS,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST_PLUS,
+ .scl_lcnt = 55,
+ .scl_hcnt = 30,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[3] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ }"
+
+ device domain 0 on
+ device ref i2c1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""ELAN901C""
+ register "generic.desc" = ""ELAN Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.detect" = "1"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "20"
+ register "generic.reset_off_delay_ms" = "2"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_delay_ms" = "280"
+ register "generic.stop_off_delay_ms" = "2"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 10 on end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""PARA3406""
+ register "generic.desc" = ""Parade Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.detect" = "1"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "20"
+ register "generic.reset_off_delay_ms" = "2"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_delay_ms" = "280"
+ register "generic.stop_off_delay_ms" = "2"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 24 on end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""GTCH7503""
+ register "generic.desc" = ""G2TOUCH Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.detect" = "1"
+ register "generic.reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "50"
+ register "generic.enable_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 40 on end
+ end
+ end
+ device ref i2c3 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ chip drivers/generic/alc1015
+ register "hid" = ""RTL1019""
+ register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ device generic 0 on end
+ end
+ end
+ device ref i2c5 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "wake" = "GPE0_DW2_14"
+ register "detect" = "1"
+ device i2c 15 on end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""SYNA0000""
+ register "generic.cid" = ""ACPI0C50""
+ register "generic.desc" = ""Synaptics Touchpad""
+ register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "generic.wake" = "GPE0_DW2_14"
+ register "generic.detect" = "1"
+ register "hid_desc_reg_offset" = "0x20"
+ device i2c 0x2c on end
+ end
+ end
+ device ref pcie_rp4 on
+ # PCIe 4 WLAN
+ register "pch_pcie_rp[PCH_RP(4)]" = "{
+ .clk_src = 2,
+ .clk_req = 2,
+ .flags = PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip drivers/wifi/generic
+ register "wake" = "GPE0_DW1_03"
+ register "add_acpi_dma_property" = "true"
+ device pci 00.0 on end
+ end
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ use conn1 as mux_conn[1]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port2 as usb2_port
+ use tcss_usb3_port2 as usb3_port
+ device generic 1 alias conn1 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C1 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
+ device ref tcss_usb3_port2 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C1 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port5 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 UFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""CNVi Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port10 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb3_port3 on end
+ end
+ end
+ end
+ end
+ end
end