mb/google/brya: Update devicetree setting for lisbon
update devicetree setting per the schematic
BUG=b:246657849
TEST=emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I4268a5b43690a22bb703337fed84b83c45da4ad2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
diff --git a/src/mainboard/google/brya/variants/lisbon/overridetree.cb b/src/mainboard/google/brya/variants/lisbon/overridetree.cb
index 4f2c04a..a2a4043 100644
--- a/src/mainboard/google/brya/variants/lisbon/overridetree.cb
+++ b/src/mainboard/google/brya/variants/lisbon/overridetree.cb
@@ -1,6 +1,311 @@
+fw_config
+ field AUDIO 0 2
+ option AUDIO_UNKNOWN 0
+ option ALC5682IVS_I2S 1
+ end
+end
+
chip soc/intel/alderlake
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| GSPI1 | NC |
+ #| I2C0 | Audio |
+ #| I2C1 | cr50 TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C3 | NC |
+ #| I2C5 | NC |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 650,
+ .fall_time_ns = 400,
+ .data_hold_time_ns = 50,
+ },
+ .i2c[1] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 600,
+ .fall_time_ns = 400,
+ .data_hold_time_ns = 50,
+ },
+ }"
- device domain 0 on
- end
+ register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2 Port 1
+ register "usb2_ports[2]" = "USB2_PORT_EMPTY" # Disable USB2 Port 2
+ register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable USB2 Port 3
+ register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 4
+ register "usb3_ports[0]" = "{
+ .enable = 1,
+ .ocpin = OC_SKIP,
+ .tx_de_emp = 0x2B,
+ .tx_downscale_amp = 0x00,
+ }" # Type-A port A0
+
+ register "serial_io_gspi_mode" = "{
+ [PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
+ [PchSerialIoIndexGSPI1] = PchSerialIoDisabled,
+ }"
+
+ register "ddi_ports_config" = "{
+ [DDI_PORT_A] = DDI_ENABLE_HPD,
+ [DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC,
+ [DDI_PORT_1] = DDI_ENABLE_HPD,
+ [DDI_PORT_3] = DDI_ENABLE_HPD | DDI_ENABLE_DDC,
+ }"
+
+ device domain 0 on
+ device ref dtt on
+ chip drivers/intel/dptf
+ ## sensor information
+ register "options.tsr[0].desc" = ""DRAM""
+ register "options.tsr[1].desc" = ""Charger""
+
+ # TODO: below values are initial reference values only
+ ## Active Policy
+ register "policies.active" = "{
+ [0] = {
+ .target = DPTF_CPU,
+ .thresholds = {
+ TEMP_PCT(85, 90),
+ TEMP_PCT(80, 80),
+ TEMP_PCT(75, 70),
+ }
+ }
+ }"
+
+ ## Passive Policy
+ register "policies.passive" = "{
+ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
+ [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
+ [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
+ }"
+
+ ## Critical Policy
+ register "policies.critical" = "{
+ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
+ [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
+ [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
+ }"
+
+ register "controls.power_limits" = "{
+ .pl1 = {
+ .min_power = 3000,
+ .max_power = 15000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 200,
+ },
+ .pl2 = {
+ .min_power = 55000,
+ .max_power = 55000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 1000,
+ }
+ }"
+
+ ## Charger Performance Control (Control, mA)
+ register "controls.charger_perf" = "{
+ [0] = { 255, 1700 },
+ [1] = { 24, 1500 },
+ [2] = { 16, 1000 },
+ [3] = { 8, 500 }
+ }"
+
+ ## Fan Performance Control (Percent, Speed, Noise, Power)
+ register "controls.fan_perf" = "{
+ [0] = { 90, 6700, 220, 2200, },
+ [1] = { 80, 5800, 180, 1800, },
+ [2] = { 70, 5000, 145, 1450, },
+ [3] = { 60, 4900, 115, 1150, },
+ [4] = { 50, 3838, 90, 900, },
+ [5] = { 40, 2904, 55, 550, },
+ [6] = { 30, 2337, 30, 300, },
+ [7] = { 20, 1608, 15, 150, },
+ [8] = { 10, 800, 10, 100, },
+ [9] = { 0, 0, 0, 50, }
+ }"
+
+ ## Fan options
+ register "options.fan.fine_grained_control" = "1"
+ register "options.fan.step_size" = "2"
+
+ device generic 0 alias dptf_policy on end
+ end
+ end
+ device ref pcie4_0 on
+ # Enable CPU PCIE RP 1 using CLK 0
+ register "cpu_pcie_rp[CPU_RP(1)]" = "{
+ .clk_req = 0,
+ .clk_src = 0,
+ .flags = PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ end
+ device ref tcss_dma0 on
+ chip drivers/intel/usb4/retimer
+ register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
+ use tcss_usb3_port1 as dfp[0].typec_port
+ device generic 0 on end
+ end
+ end
+ device ref cnvi_wifi on
+ chip drivers/wifi/generic
+ register "wake" = "GPE0_PME_B0"
+ device generic 0 on end
+ end
+ end
+ device ref i2c0 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on
+ probe AUDIO ALC5682IVS_I2S
+ end
+ end
+ end #I2C0
+ device ref i2c1 on
+ chip drivers/i2c/tpm
+ register "hid" = ""GOOG0005""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
+ device i2c 50 on end
+ end
+ end
+ device ref pcie_rp7 on
+ chip drivers/net
+ register "wake" = "GPE0_DW0_07"
+ register "led_feature" = "0xe0"
+ register "customized_led0" = "0x23f"
+ register "customized_led2" = "0x028"
+ register "enable_aspm_l1_2" = "1"
+ device pci 00.0 on end
+ end
+ end # RTL8111 Ethernet NIC
+ device ref pcie_rp8 on
+ chip soc/intel/common/block/pcie/rtd3
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
+ register "srcclk_pin" = "3"
+ device generic 0 on end
+ end
+ end #PCIE8 SD card
+ device ref gspi1 off end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A3 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(5, 1))"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A2 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(6, 1))"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))"
+ device ref usb2_port9 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port10 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))"
+ device ref usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A1 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb3_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A2 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(6, 1))"
+ device ref usb3_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A3 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(5, 1))"
+ device ref usb3_port4 on end
+ end
+ end
+ end
+ end
+ end
end