Unify setting 82801a/b/c/d IOAPIC ID
Remove obscure local copy of writing the ioapic registers.
Change-Id: I133e710639ff57c6a0ac925e30efce2ebc43b856
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2532
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
diff --git a/src/southbridge/intel/i82801ax/Kconfig b/src/southbridge/intel/i82801ax/Kconfig
index 70734a7a..71ae016 100644
--- a/src/southbridge/intel/i82801ax/Kconfig
+++ b/src/southbridge/intel/i82801ax/Kconfig
@@ -19,6 +19,7 @@
config SOUTHBRIDGE_INTEL_I82801AX
bool
+ select IOAPIC
select HAVE_HARD_RESET
select USE_WATCHDOG_ON_BOOT
diff --git a/src/southbridge/intel/i82801ax/lpc.c b/src/southbridge/intel/i82801ax/lpc.c
index c9404ed..1d296f4 100644
--- a/src/southbridge/intel/i82801ax/lpc.c
+++ b/src/southbridge/intel/i82801ax/lpc.c
@@ -70,17 +70,30 @@
* Use the defined IRQ values above or set mainboard
* specific IRQ values in your devicetree.cb.
*/
-static void i82801ax_enable_apic(struct device *dev)
-{
- u32 reg32;
- volatile u32 *ioapic_index = (volatile u32 *)IO_APIC_ADDR;
- volatile u32 *ioapic_data = (volatile u32 *)(IO_APIC_ADDR + 0x10);
+
+/**
+ * Enable ACPI I/O range.
+ *
+ * @param dev PCI device with ACPI and PM BAR's
+ */
+static void i82801ax_enable_acpi(struct device *dev)
+{
/* Set ACPI base address (I/O space). */
pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
/* Enable ACPI I/O range decode and ACPI power management. */
pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
+}
+
+/**
+ * Set miscellanous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801ax_enable_ioapic(struct device *dev)
+{
+ u32 reg32;
reg32 = pci_read_config32(dev, GEN_CNTL);
reg32 |= (1 << 13); /* Coprocessor error enable (COPR_ERR_EN) */
@@ -90,18 +103,7 @@
pci_write_config32(dev, GEN_CNTL, reg32);
printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
- *ioapic_index = 0;
- *ioapic_data = (1 << 25);
-
- *ioapic_index = 0;
- reg32 = *ioapic_data;
- printk(BIOS_DEBUG, "Southbridge APIC ID = %x\n", reg32);
- if (reg32 != (1 << 25))
- die("APIC Error\n");
-
- /* TODO: From i82801ca, needed/useful on other ICH? */
- *ioapic_index = 3; /* Select Boot Configuration register. */
- *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
+ set_ioapic_id(IO_APIC_ADDR, 0x02);
}
static void i82801ax_enable_serial_irqs(struct device *dev)
@@ -219,8 +221,9 @@
/* Set the value for PCI command register. */
pci_write_config16(dev, PCI_COMMAND, 0x000f);
+ i82801ax_enable_acpi(dev);
/* IO APIC initialization. */
- i82801ax_enable_apic(dev);
+ i82801ax_enable_ioapic(dev);
i82801ax_enable_serial_irqs(dev);
diff --git a/src/southbridge/intel/i82801bx/Kconfig b/src/southbridge/intel/i82801bx/Kconfig
index 00cb5bf..3d725d4 100644
--- a/src/southbridge/intel/i82801bx/Kconfig
+++ b/src/southbridge/intel/i82801bx/Kconfig
@@ -19,6 +19,7 @@
config SOUTHBRIDGE_INTEL_I82801BX
bool
+ select IOAPIC
select HAVE_HARD_RESET
select USE_WATCHDOG_ON_BOOT
diff --git a/src/southbridge/intel/i82801bx/lpc.c b/src/southbridge/intel/i82801bx/lpc.c
index 0ff44e6..0533afb 100644
--- a/src/southbridge/intel/i82801bx/lpc.c
+++ b/src/southbridge/intel/i82801bx/lpc.c
@@ -72,17 +72,29 @@
* Use the defined IRQ values above or set mainboard
* specific IRQ values in your devicetree.cb.
*/
-static void i82801bx_enable_apic(struct device *dev)
-{
- uint32_t reg32;
- volatile uint32_t *ioapic_index = (volatile uint32_t *)IO_APIC_ADDR;
- volatile uint32_t *ioapic_data = (volatile uint32_t *)(IO_APIC_ADDR + 0x10);
+/**
+ * Enable ACPI I/O range.
+ *
+ * @param dev PCI device with ACPI and PM BAR's
+ */
+static void i82801bx_enable_acpi(struct device *dev)
+{
/* Set ACPI base address (I/O space). */
pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
/* Enable ACPI I/O range decode and ACPI power management. */
pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
+}
+
+/**
+ * Set miscellanous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801bx_enable_ioapic(struct device *dev)
+{
+ u32 reg32;
reg32 = pci_read_config32(dev, GEN_CNTL);
reg32 |= (1 << 13); /* Coprocessor error enable (COPR_ERR_EN) */
@@ -92,18 +104,7 @@
pci_write_config32(dev, GEN_CNTL, reg32);
printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
- *ioapic_index = 0;
- *ioapic_data = (1 << 25);
-
- *ioapic_index = 0;
- reg32 = *ioapic_data;
- printk(BIOS_DEBUG, "Southbridge APIC ID = %x\n", reg32);
- if (reg32 != (1 << 25))
- die("APIC Error\n");
-
- /* TODO: From i82801ca, needed/useful on other ICH? */
- *ioapic_index = 3; /* Select Boot Configuration register. */
- *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
+ set_ioapic_id(IO_APIC_ADDR, 0x02);
}
static void i82801bx_enable_serial_irqs(struct device *dev)
@@ -237,8 +238,10 @@
/* Set the value for PCI command register. */
pci_write_config16(dev, PCI_COMMAND, 0x000f);
+ i82801bx_enable_acpi(dev);
+
/* IO APIC initialization. */
- i82801bx_enable_apic(dev);
+ i82801bx_enable_ioapic(dev);
i82801bx_enable_serial_irqs(dev);
diff --git a/src/southbridge/intel/i82801cx/Kconfig b/src/southbridge/intel/i82801cx/Kconfig
index 17e90e8..3e01cb81 100644
--- a/src/southbridge/intel/i82801cx/Kconfig
+++ b/src/southbridge/intel/i82801cx/Kconfig
@@ -1,4 +1,4 @@
config SOUTHBRIDGE_INTEL_I82801CX
bool
+ select IOAPIC
select HAVE_HARD_RESET
-
diff --git a/src/southbridge/intel/i82801cx/lpc.c b/src/southbridge/intel/i82801cx/lpc.c
index a1ffb8f..79998bc 100644
--- a/src/southbridge/intel/i82801cx/lpc.c
+++ b/src/southbridge/intel/i82801cx/lpc.c
@@ -24,34 +24,24 @@
#define MAINBOARD_POWER_ON 1
-static void i82801cx_enable_ioapic( struct device *dev)
+/**
+ * Set miscellanous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801cx_enable_ioapic(struct device *dev)
{
- uint32_t dword;
- volatile uint32_t* ioapic_index = (volatile uint32_t*)IO_APIC_ADDR;
- volatile uint32_t* ioapic_data = (volatile uint32_t*)(IO_APIC_ADDR + 0x10);
+ u32 reg32;
- dword = pci_read_config32(dev, GEN_CNTL);
- dword |= (3 << 7); /* enable ioapic & disable SMBus interrupts */
- dword |= (1 <<13); /* coprocessor error enable */
- dword |= (1 << 1); /* delay transaction enable */
- dword |= (1 << 2); /* DMA collection buf enable */
- pci_write_config32(dev, GEN_CNTL, dword);
- printk(BIOS_DEBUG, "ioapic southbridge enabled %x\n",dword);
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ reg32 |= (1 << 13); /* Coprocessor error enable (COPR_ERR_EN) */
+ reg32 |= (3 << 7); /* IOAPIC enable (APIC_EN) */
+ reg32 |= (1 << 2); /* DMA collection buffer enable (DCB_EN) */
+ reg32 |= (1 << 1); /* Delayed transaction enable (DTE) */
+ pci_write_config32(dev, GEN_CNTL, reg32);
+ printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
- // Must program the APIC's ID before using it
-
- *ioapic_index = 0; // Select APIC ID register
- *ioapic_data = (2<<24);
-
- // Hang if the ID didn't take (chip not present?)
- *ioapic_index = 0;
- dword = *ioapic_data;
- printk(BIOS_DEBUG, "Southbridge apic id = %x\n", (dword>>24) & 0xF);
- if(dword != (2<<24))
- die("");
-
- *ioapic_index = 3; // Select Boot Configuration register
- *ioapic_data = 1; // Use Processor System Bus to deliver interrupts
+ set_ioapic_id(IO_APIC_ADDR, 0x02);
}
// This is how interrupts are received from the Super I/O chip
diff --git a/src/southbridge/intel/i82801dx/i82801dx.h b/src/southbridge/intel/i82801dx/i82801dx.h
index d9e4d38..2da7759 100644
--- a/src/southbridge/intel/i82801dx/i82801dx.h
+++ b/src/southbridge/intel/i82801dx/i82801dx.h
@@ -82,6 +82,7 @@
#define PMBASE_ADDR 0x0400
#define DEFAULT_PMBASE PMBASE_ADDR
#define ACPI_CNTL 0x44
+#define ACPI_EN (1 << 4)
#define BIOS_CNTL 0x4E
#define GPIO_BASE 0x58
#define GPIO_CNTL 0x5C
diff --git a/src/southbridge/intel/i82801dx/lpc.c b/src/southbridge/intel/i82801dx/lpc.c
index fbf8e12..0644569 100644
--- a/src/southbridge/intel/i82801dx/lpc.c
+++ b/src/southbridge/intel/i82801dx/lpc.c
@@ -36,37 +36,38 @@
typedef struct southbridge_intel_i82801dx_config config_t;
-static void i82801dx_enable_ioapic(struct device *dev)
+/**
+ * Enable ACPI I/O range.
+ *
+ * @param dev PCI device with ACPI and PM BAR's
+ */
+static void i82801dx_enable_acpi(struct device *dev)
{
- u32 reg32;
- volatile u32 *ioapic_index = (volatile u32 *)(IO_APIC_ADDR);
- volatile u32 *ioapic_data = (volatile u32 *)(IO_APIC_ADDR + 0x10);
-
/* Set ACPI base address (I/O space). */
pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
- /* Enable ACPI I/O and power management. */
- pci_write_config8(dev, ACPI_CNTL, 0x10);
+ /* Enable ACPI I/O range decode and ACPI power management. */
+ pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
+}
+
+/**
+ * Set miscellanous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801dx_enable_ioapic(struct device *dev)
+{
+ u32 reg32;
reg32 = pci_read_config32(dev, GEN_CNTL);
- reg32 |= (3 << 7); /* Enable IOAPIC */
- reg32 |= (1 << 13); /* Coprocessor error enable */
- reg32 |= (1 << 1); /* Delayed transaction enable */
- reg32 |= (1 << 2); /* DMA collection buffer enable */
+ reg32 |= (1 << 13); /* Coprocessor error enable (COPR_ERR_EN) */
+ reg32 |= (3 << 7); /* IOAPIC enable (APIC_EN) */
+ reg32 |= (1 << 2); /* DMA collection buffer enable (DCB_EN) */
+ reg32 |= (1 << 1); /* Delayed transaction enable (DTE) */
pci_write_config32(dev, GEN_CNTL, reg32);
printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
- *ioapic_index = 0;
- *ioapic_data = (1 << 25);
-
- *ioapic_index = 0;
- reg32 = *ioapic_data;
- printk(BIOS_DEBUG, "Southbridge APIC ID = %x\n", reg32);
- if (reg32 != (1 << 25))
- die("APIC Error\n");
-
- *ioapic_index = 3; /* Select Boot Configuration register. */
- *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
+ set_ioapic_id(IO_APIC_ADDR, 0x02);
}
static void i82801dx_enable_serial_irqs(struct device *dev)
@@ -267,6 +268,7 @@
/* Set the value for PCI command register. */
pci_write_config16(dev, PCI_COMMAND, 0x000f);
+ i82801dx_enable_acpi(dev);
/* IO APIC initialization. */
i82801dx_enable_ioapic(dev);